Black vertical rectangular box on my screen

Similar Questions

• Satellite 1410-303: black vertical banner on the far right of the screen

  Hi all

  I had to format my Satellite 1410 303, and then I added also 256 MB of RAM so the total is now 512 MB. It works fine but the problem is that now I have a black vertical bar, which covers about one inch from the far right of the screen and when you move the mouse it the "offsets" to the right, but the black bar monitor remains in place. Very annoying.

  Also, since I formatted the laptop, I do not have the controls in Toshiba or utility, so I can't change the width of the screen, or perform any other work related operations.

  Your help is very appreciated.

  As a first step, it will be interesting to know something about the pre-installed OS and drivers. I assume that you used your own CD of facilities and the recovery media not original. Am I right about that?

  What drivers you have installed, in particular display driver?

• Black vertical line on screen

  My Dell laptop has a black vertical band that is approximately 1 inch wide that appears and then disappears near the area of the Start button.  It goes off the left side of the screen.

  Please notify.

  Connect an external monitor - if the fault does not show, it's the Billboard that is bad - you will need a new.

  If it appears to the outside, you have a bad video chip or card - replace the card mother or video card, depending on your system has.

• Whenever I start my computer a black rectangular box appears and says "C:\windows\system32\cmd.exe".

  * Original title: popup?

  Whenever I start my computer, a black rectangular box appears and says "C:\windows\system32\cmd.exe" immediately after a grey box appears saying "Windows cannot find"C:\Users\Amber\AppData\Local\browser extensions\client.exe". Make sure you typed the name correctly and then try again.

  Hello

  It seems to be a left over Malware boot entry that was removed from your security programs.

  Download, install, update and scan your system with the free version of Malwarebytes AntiMalware:

  http://www.Malwarebytes.org/products/malwarebytes_free

  It is a very good program to scan your system to remove adware, etc.:

  http://www.bleepingcomputer.com/download/adwcleaner/

  AdwCleaner is a program that finds and removes the Adware, toolbars, potentially unwanted programs (PUP) and browser hijackers from your computer.  Using AdwCleaner you can easily more of these types of programs for a better user experience on your computer delete and while browsing the web.

  @@@@@@@@@@@@@@@@@@@@@@@@@@@@@@

  If the problem persists after scanning, take these startup entries:

  "How to use the System Configuration tool in Windows 8/8.1.

  http://www.7tutorials.com/how-use-system-configuration-tool-all-its-awesomeness

  "With the help of Configuration (msconfig) system.

  http://Windows.Microsoft.com/en-us/Windows/using-system-configuration#1TC=Windows-8

  You can also use this free program to do, too:

  "Autoruns for Windows V12.03"

  http://TechNet.Microsoft.com/en-us/sysinternals/bb963902.aspx

  See you soon.

• Black horizontal lines on the LCD screen at a specific time during the start and stop

  Hi, I am currently using a Presario CQ61 Notebook PC.  My problem, as indicated in the title, are black lines on the LCD screen, apparently when the screen is reset or enclose itself turned off during the start and stop only. From the judgment, he produced a split second her stops the hard drive, after that the screen is black. The lines and then quickly disappear. At startup, lines appear after the Windows logo has passed and the screen went from black to start loading the login screen.

  The LCD is in perfect condition, all using the PC. No line, no discoloration, etc.. Nothing extraordinary either. The problem does occur only during these two periods, specifically. I am also unable to note the lines when I'm looking directly at the screen. I have to be standing next to the PC, at an angle.

  Now, I had this PC for a considerable amount of time, however, I never paid much attention to the screen when starting upwards or stop, so this could definitely be something that the laptop has done since I bought it. I also read on similar problems, and it could be an outdated video driver or BIOS.

  I want to just make sure that it is not a major problem. Thank you all!

  Hello

  You have a few options in my opinion please try these steps can help you solve your problem.

  1) click Start, type msconfig.exe in the start search box and press ENTER to start the System Configuration utility. Under the Services tab, click to select the hide all Microsoft services check box, and then go to tap Start , click on disable all. Click apply OK restart the device.

  (2) please visit the HP website and update the Bios and graphics drivers on the unit.

  Let us know how it goes!

  * Although I am an employee of HP, I speak for myself and not for HP.

  Click the White Star Kudos to say thank you *.

  Please check accept as Solution if it solves your problem *.

  Concerning

  Maton

• Since the upgrade to 8.0, when navigation between screens, my computer screen becomes black for 1 second before the screen is redrawn. This happens regularly and is a major nuisance. It simulates a power failure. It does not happen with IE.

  Since the upgrade to 8.0, when navigation between screens, my computer screen becomes black for 1 second before the screen is redrawn. This happens regularly and is a major nuisance. It simulates a power failure. It does not happen with IE.

  Here I answer to my problem: I upgraded my graphics card and the problem seems to have disappeared.

• Blue vertical line appear on the screen of the series M Satellite

  I had a blue vertical line appear on my screen its about inch thick and is at - it start, can someone tell me if I can get rid of him? Thank you.

  Hello

  If this blue line is present from the first second after turning on the laptop that I presume it's because of the faulty graphics card. To be sure try to connect an external display to see the same thing will happen. If Yes, it is the evidence that this line occurs due to faulty hardware.

• HP Officejet Pro 8600 more black vertical line when copy or scan

  HP Officejet Pro 8600 more black vertical line when copy or scan everything in the middle of the page

  Hi Clementstl,

  I understand that you have a 8600 Pro Officejet which puts a black vertical line in the center of your copies/scans. I'm sorry to hear you had to deal with this, but I will certainly do my best to help you solve this problem.

  I recommend the rest of this document of vertical stripes, lines or streaks in the Copies, faxes or Scans as it should be in a position to help to cross that line. The most common cause is a small spot of something on the glass of the scanner, so just make sure that when you're cleaning use you as much elbow grease you can collect

  Just to clarify a little further, if the problem only seems to occur when you use the automatic document feeder, you'll want to focus your attention on the small strip of glass that he uses on the left side. If it only occurs when you use the flat glass, you want to concentrate on the large piece of glass he uses.

  Hope this helps, have a nice day!

• Satellite P30 - three vertical lines appeared on the screen

  I have a problem with the display on my p30 110 three vertical lines appeared on the screen, the pc has been scanned with three different antivirus programs and seems to be clean any suggestions would be helpful

  Hello

  These problems usually occur due to a malfunction of the equipment.
  But have you tried to update the graphics driver. If this isn't the case, so I recommend to do.
  The update may solve some problems.

  However, if vertical lines persists then you should ask Toshiba service for assistance.
  He must check the laptop.

• DeskJet 3835: Black vertical lines when scanning - Deskjet 3835

  Hello

  Whenever I scan using the document feeder, there are black vertical lines showing on the picture. This happens with the dish however. The printer is the 3835 Deskjet all in one set. Receive your answer. Thank you.

  The lines that you describe would generally caused by a small file specifications (or some spec) on the thin glass to the left of the bed main scanner.  Open the scanner cover and clean the thin glass.  It can help to shine a bright light which is held at a slight angle to the bed of the front.  This would be to highlight the areas to be cleaned.

• OfficeJet pro 8600 black vertical lines of print when copying

  I got a new of OfficeJet Pro 8600 a couple of weeks, and it worked fine until today, when I tried to copy something. I can always print from my pc and scan without problem, but when I try to copy a document (if I load it into the tray or put it on the scanner) the page comes out covered with black vertical lines of different sizes. It seems that this isn't the ink or the scanner since I can print from my pc and analysis very well.

  Help, please!

  This unit is plugged into a wall outlet directly? If this isn't the case, then try to connect the unit to a wall outlet directly.

  The 8600 Officejet Pro has built in the surge protector and double this feature may cause some problems.

  Also, try to reset the printer hard:
  * Unplug the unit while the printer is on
  Disconnect the other end of the power cable from the wall socket direct
  * Wait 30 seconds
  * Plug the unit to the top

  Let me know if it helps.

• a pink vertical line appeared on my screen

  A thin pink vertical line appeared on my screen. How can I get rid of him. I tried the obvious bases.

  You probably have a line of dead or stuck pixels on your LCD screen. There are programs that carry out the display of this bike through various display models and some people recommend massaging where the pixel stuck watch manually.

  Video exercise programs show some real promise, but I'm not sure a lot of the other supposed fixed. Personally, I think that many of these patches are as a cure for sneezing that they are no longer for the laugh of the person who provided the remedy in the interest of the person in arrears by sneezing. In addition, if the pixel has become unstuck, you can always ask success.

  Use Bing or Google to find dead pixel and you will get a multitude of solutions thrown your way. Exercise video display may be worth trying.

• All-in-one HP Office Pro 8610: black vertical line on the scans

  I have a black vertical line down my scans and copies that are feeding by automatic feeding (8610 Office Pro HP all in one)

  As I read a few issues on the forum, I could solve this problem by opening the top loader and wipe the glass with a "lens Wipe" wipe Strip

• When I right click to create a shortcut or print, a blue rectangular box remains on my desk with the words it contains what I right clicked to do.

  When I right click to create a shortcut or in block letters or what I do from the dropdown menu, a blue rectangular box with the words it contains, stays on my desk.  The only way I can get rid of it is by restarting the computer.  Anyone know how to fix this; or it could be the cause?

  Hello
  • What were the changes made before the problem occurred?
  • How long you have been facing this problem?

  You can follow the procedure below:

  Stage I.
  Check to see if the problem exists in Safe Mode, if the computer works as expected in mode without failure, then we can solve the problem in the clean boot state.
  a. refer to the article below for the procedure safe mode in Windows XP
  A description of the options to start in Windows XP Mode
  http://support.Microsoft.com/kb/315222

  Stage II.
  You need to perform a clean boot to find the program that is causing and then disable or remove. If the computer starts successfully in safe mode and then set the computer to start with clean boot safe mode.
  How to configure Windows XP to start in a "clean boot" State
  http://support.Microsoft.com/kb/310353/en-us
  Note: When you are finished troubleshooting, follow the steps as explained in the article to reset the computer to start as usual.

   

• Vertical bars, thin, white full screen of WMP11

  With the help of Dell Dimension 4700, 3 GB RAM, EVGA GeForce 8400 GS with 512 MB, Windows XP SP3, SoundSpectrum G-Force 3.9.4.

  When I open WMP11, then select show improvements, then close show improvements, then go to the mode full screen... There's a mess of thin, white vertical bars.  This is equivalent to any visualization I select, or if no view is selected.

  No matter what I do - short of closing and reopening of WMP - him reappear the white vertical bars in mode full-screen.

  Is this a known problem with WMP11?  No matter what known fix?  I searched 'vertical bars' in music and its Forum and found nothing.  Thank you very much!

  I had the same problem, and before that I played with it too much I did research. These messages have helped me do a bit of that research. I also think that it may be useful to mention that I have a Radeon 5700 series, I use my TV 32 inches as my screen via the HDMI connection available on the vid card. Levels at 1600 x 900 is enabled. I am a COMPUTER professional and nothing of what I read seemed logical as to the root causes of this issue. I use this workstation for all and everything under the Sun, audio recording and mixing, capture video and administration of editing systems, encoding, gaming, etc. Basically, I make the most of my very competent and versatile Windows operating system. Sometimes, the simplest thing is the answer. In my case, it seemed that this was the case. I can't say I've done work for everyone, but it worked for me. That said, here's what I did to fix the problem. (I did all that, although not in full screen, still playing album The Roots Things Fall Apart I was listening too when I arrived in this issue)

  1. I disabled the visualization.
  2. I have a right-click on the screen and selected More Options...
  3. Click the Plug-ins tab. You should see the list of categories on the left and the right corresponding sub categories list.
  4. My category of visualization has been selected by default. On the right will be the list of visualizations that you have installed. (I have only the defaultAlchemy,Bars and wavesandbattery installed) When you have a view selected, you should see a section in this same window just below the list of categories.
  5. It should be a Properties button available when a specific view is selected.
  6. I tried to use properties for all the visualizations except battery and I got a message that says that this plug-in does has no properties that you can set.
  7. When I went into the properties of the battery there are 2 settings I could adjust. Screen size under full screen settings and the off-screen buffer size under Player settings.
  8. Only, I've adjusted setting the screen size to match my resolution (1600 x 900). I did adjust the other settings.
  9. I clicked OK to close this window. I clicked on apply and thenOK in the window main options.
  10. I activated the visualization of my preference. (Battery is being my favorite)
  11. I went full-screen, and the white bars. Visualization worked perfectly.
  12. I tried the other visualizations and got the same result with each of them.

  Hope that this clear and the most important is useful.

  http://www.Speedtest.net/result/888894683.PNG

  http://www.Pingtest.net/result/20846112.PNG