BlackBerry 8800 Smartphone keeps rebooting after installing v4.5.0.110

Similar Questions

• RESOLVED: Loop of reboot after installing new disks in RAID of PERC S100

  A customer has a Dell T110 (with a PERC S100 RAID controller) running Windows 2008 R2. The system has two disks: a reader not RAID (C :) running the operating system and a RAID1 drive (E :) sharing data with network folders.) We need to install again, larger disks for the RAID.

  I thought I could backup the data on the RAID drive existing (e), install new disks, built a new table in the S100 (VDM) virtual disk boot manager, boot into the operating system, create the new partition for the data replaced E: drive and copy the data back. This was not the case. After installing the new disks and the new array of construction (which is reported as "READY (R/W)" when starting, Windows starts all the way in "press CTRL-ALT-DEL to log". After two or three seconds, the system reboots. The same thing happens when I try to start safe mode. The system IS NOT automatically booted to the Recovery Console. He never seems to know that an error occurred and the system was not shut down normally.

  I booted into the Recovery Console, installed the drivers for the PERC S100 and run recovery to start without success. Also in the Recovery Console, I ran 'chkdsk /f E:\. ' (remarkably, the drive letter for the data drive remained the same), and no error has been reported. I also reinstalled drivers S100 of the recovery using DISM Console, but that changed nothing.

  I started to 8.1 Windows PE, installed drivers S100, formatted the virtual disk, copied the data which he, and everything works fine. The only problem is when I try to boot from the system drive (which has no problem) with the new installed disks.

  When I put the old records, the system boots normally with no reconfiguration required. The VDM to start automatically remembers the discs and the table. Nothing shows up in the logs event indicating that there was an error during startup. (Ntbtlog.txt) start-up newspaper, after several boots with the new drives in place, indicates that the system restarts at various times during loading drivers. There is nothing coherent in the startup log to indicate what the problem is.

  The only clue I have is that, during the startup, the VDM reports the virtual drive of origin as 'NORMAL (R/W)' and the new virtual disk as "READY (R/W)", but I'm not sure of the significance of this difference or if it suggests a solution.

  I can't find clues in all the newspapers about what may be the problem. If anyone has any suggestions, I will be grateful. I'll be especially grateful for the wacky suggestions.

  I ran it. Nothing appeared unusual. However, I does not solve the problem.

  I connect the new readers to the same SATA ports as the old records. When I connect one of them to the SATA port that had not been used as part of the original painting, the VDM S100 reported the original failed array, because readers were is more connected and showed the new table as a LOAN. The operating system then started normally.

  The trick, it seems that you should remove the old virtual disk before connecting the new disks on the same ports.

• Problem blackberry 8800 Smartphone blackBerry uninstalling programs

  I have a problem on blackberry 8800, I installed the new version of app world, the official website and I downloaded and installed xmplayer lite, I wanted to uninstall it and I went to options / advanced options and applications, choose the program to uninstall and choose Remove in the list of programs which are no longer exists, but instead is always present in the cell and works If I try to go into the options to uninstall, no longer appears in the list. How? I tried to put it and turn it back on and remove and replace the battery, thanks

  Go to Options-> advanced-> applications-> MENU-> MODULES and check if you can find. And then delete a from there and restart.

• BlackBerry Smartphones keep restarting after new update BBmessenger

  
  

  You are able to reboot your device in SafeMode as shown in KB17877?

  I guess, because it is taken in a reboot cycle, when you connect to the desktop software it does not have a stable connection to reinstall your software?

  If this is the case, remove the battery and keep it off when you connect to the desktop software. You will get a pop up that the device cannot connect and there should be buttons retry, update and cancel. Select Update and you will then be able to reinstall the latest version of the device software.

  When the load progresses, you will see a step that says "waiting for initialization of the devices '. At this point, insert the battery and recharging must complete.

• Software BlackBerry BB link keeps reminding to install the 4181 Update

  -Have been updated to the latest version 10.1.0.4181 by BlackBerry Link software, checking that the version on the device is the latest version. -A device to reboot several times. After plugin the USB port & link to BB running, he always reminds to install update. pls advise, thanks.

  Don' don'tknow if this will help, but I temporarily disabled the antivirus and firewall, ran a backup and synchronization in the link, then restarted the PC and re-connected the phone... went problem (in my case anyway )

• BlackBerry curve Smartphones 9320 200 after update error message

  My phone died now :-(

  When I connect my phone to the desktop software this morning he gave me an update message.  I've dutifully updated - and my phone is dead.   I removed all office cleaned of all other files and reloaded software but still not you connect phone to pc.  It simply keeps restart until the error 200 message once again!

  Any suggestions gratefully received.  It was working perfectly until the attempt of the last version of the software download.

  Hello and welcome to the community!

  Something was wrong with the update, and now a reload is necessary. The easiest way is, on a PC (you can not do on MAC):

  (1) make sure that you have a current backup and your BB complete... you can find the instructions at the link in my auto-sig below.

  2) uninstall all the BB OS packages from your PC,

  (3) make sure you have the BB Desktop Software already installed

  • http://us.BlackBerry.com/software/desktop.html

  (4) download and install on your computer, the BB OS package you want:

  • http://us.BlackBerry.com/support/downloads/download_sites.jsp
  • If all you want are the levels of BONE, it is first sorted by carrier - the carrier supports, your search will be fast. However, some carriers are much slower than others to release updates. To really get the package up-to-date OS for your BB, you need to dig through and find all businesses that support your specific model BB and then compare the BONE levels they support.

  5) remove all copies of the SELLER on your PC. XML... There will be at least one and maybe 2, and they will be located in the same way or to (it changes based on your version of Windows) these files:

  • C:\Program Files (x 86) \Common Files\Research In Motion\AppLoader
  • C:\Users\(your Windows username) \AppData\Roaming\Research In Motion\BlackBerry\Loader XML

  6 (a) to change your level of BB OS installed (at level or lower), you can run the Desktop software and connect your BB... the software should offer the operating system package you have installed on your PC.

  6 (b) or, for recharging your BB OS level installed as well to change, work around the Desktop software and use the CHARGER. EXE directly, through step 2 in this process:

  • http://supportforums.BlackBerry.com/T5/BlackBerry-device-software/how-to-reload-your-operating-syste...
  • Note Although written to "recharge" and the storm, it can be used to upgrade, downgrade or recharge any BB device model - depends on the operating system package you download and install on your PC.

  If, during the process of 6a or 6 b, your BB has an error '507', simply unplug the USB of the BB cord and reinsert it. do nothing else... This should allow the installation to continue.

  You can also study the use of BBSAK (bbsak.org) to perform the wipe what he is capable.

  You can also try the "skeleton OS Reload procedure" in an attempt to circumscribe the precise causal element:

  1. Load your OS "bare bones"... If everything is optional, do not install it.
  2. If the behavior is immediately, then try another OS with step 1
  3. If the behavior does not immediately, then run for as long as necessary to make you to be sure that the behavior will not occur.
  4. Add one more thing - no matter how tempting, one.
  5. If the behavior does not immediately present, and then runs for long enough to be sure he won't have the same problem
  6. Repeat steps 4 and 5 until all things are responsible or the behavior presents

  When the behavior shows up, you know the culprit... the last thing you have loaded.

  If the behavior doesn't re-present, then you know that step 1 or 2 cured it.

  If the behavior has anything, then you have probably a problem of material level for which no amount of OS or software can heal.

  You may also use these tips:

  • KB10144 How to force detect the BlackBerry smartphone using the Application Loader
  • KB27956 How to recover a BlackBerry smartphone from any State
  • http://CrackBerry.com/BlackBerry-101-lecture-12-how-reload-operating-system-nuked-BlackBerry

  Good luck and let us know!

• iMac late 2012 edition hangs on reboot after installing Sierra

  I installed on my iMac, edition end of 2012 Sierra, and now it crashes when rebooting and turns off (black screen).

  It has worked very well since the upgrade to Sierra yesterday, but this morning I rebooted and the iMac stop at Midway through the boot process. I turned on several times, but it keep crashing to half way through the implementation process and turns off the power (Black screen and power total power off).

  I reboot in Recovery mode, (key command-R during restart) and am currently OS X via my latest TimeMachine recovery upward. According to the screen, the restoration will take about 2 hours to complete.

  If someone has encountered this problem, and if so, will identify you the cause of the problem?

  No problem on my Mac Pro 2010 but usually this kind of problem can be traced back to the 3rd install party who tries to run at startup.

  If the problem persists try to start in safe mode

  Try safe mode if your Mac does not end commissioning - Apple Support

• Black screen with mouse pointer count on reboot after installing SP3

  I tried to install Service Pack 3 on a PC running XP Home Edition (new installation).

  Although Microsoft Update has finished installing SP3 and the computer reboots, I get the XP installation screen base with the message "Please wait...". ", which disappears after a few seconds, leaving me with a black screen with only the mouse pointer.

  The mouse pointer moves then the PC broke down, well that no matter how long I leave nothing happens.

  I tried to uninstall SP3 and do it again (when I Uninstall SP3, Windows starts very well) and also uninstall SP3 as well as my Antivirus and try the installation again. But whenever I'm just left whit black screen.

  Try to update with the custom option.  I had problems like this before.  Usually you are missing a driver or something of this kind that makes you hang.  To update while the custom option, with the exception of SP3.  Reboot several times the installation of updates with the "Custom" option  Once all updates have been installed except SP3, you can try SP3 and see what happens.  This usually takes care of it when I have the same problem. Serving the community one computer at a time www.therushvillecomputerguy.com please post a reply to let us know whether or not our response helped.

• HP Envy 4-1115dx-keep rebooting after restore

  Hello fields,

  I have this urge to Touchsmart HP 4-1115dx provided with Windows 8 is installed.

  As it came with 500 GB hard drive that I needed to 1 TB, so I replaced the HARD drive with steps below.

  1. made HP recovery via 32 GB Flash Drive of Windows 8 media player.

  2. She confirmed the 500 GB running recovery and it worked fine.
  3. now, I opened the laptop and replaced the hard drive.
  4A ran via USB on 1 TB hard recovery.

  Everything has been normal and all software (default HP), carried out with success, but in the end she has restarted and since then it keep restarting over and over again.

  It gave some error of RAID and I have remove this volume.

  I ran back and finished in the same place again and now again after restart window logon screen.

  Please help someone,

  Kind regards

  P. S.

  I install plain Windows 8, but I want to configure the recovery back?

  just tried again and it seems that the problem caused by the RAID Volume that I delete it earlier gave me a message to go by CTRL + I? If Yes can I do to this return wolume?

  They are smart enough to get money from customers, but there are other ways to solve it, and as I don't have an answer from someone to solve so I did it my way.

  You need following things and a bit of work to solve the

  • External drive WD at least 20 GB of free space
  • An additional computer / laptop to make bootable USB
  • BootCD Hiren CD or Acronis True ImageSoftware (first available for free and a second trial can do magic)

  Follow below steps and you "ll do work

  • Insert your hard drive in computer (that came with your laptop)
  • Reset or run recovery on your computer
  • After a successful Installation
  • Download Acronis True Image or use HIREN CD/USB to use acronis to---> make a bootable USB stick (you can make usb bootable of their trial version as well)
  • Restart your system and boot with Acronis Bootable USB or HIREN USB or a CD Hiren
  • Now make a BACKUP of your entire DRIVE DISC and save the image on your WD drive - remember all the disc not a few partitions (it takes an hour to complete.
  • When it's done to Shut Down the Laptop and connect your new hard drive to it
  • Yet once start from ACRONIS or HIREN and then run the RESTORE disc
  • Select WD hard drive image and let it run on any disk (even takes one hour)
  • When it's done, turn off your computer
  • Remove all USB and WD drive

  It is quick and your recovery disc and HP Recovery USB will work also on it

  Enjoy

• Windows 8 keeps rebooting after installation

  I need help.

  So, after the death of my hard drive, I picked up a new and installed windows 8 via a USB port.

  After having met a loop without end of installation, I arrived at the first marketing of the time. However, when I got the sign in the section, the pc crashed and restarted. Then it happened again and again and again.

  At one point, he gave me a Windows has not been loaded properly and gave me a lot of options. I tried auto repair, didn't work. And now it will not even to that screen more, have a "disk read error" every time the AutoFix runs and restarts.

  Any help that can be provided will be appreciated.

  Hello

  Thanks for posting your query on the Microsoft Community.

  According to the description, I understand that you can't start your computer, Windows 8 and it keeps restarting. I will certainly help you get this fixed number.

  I suggest you follow the advice given by Mann_Manohar answered December 29, 2014 in the below mentioned thread and check if this is useful:

  http://answers.Microsoft.com/en-us/Windows/Forum/windows8_1-update/a-disk-read-error-ocurred-message-on-boot-Windows/f1c2336d-3adf-4D37-AB35-beb4f10ea16d

  Note: changes to the BIOS/complementary metal oxide semiconductor (CMOS) settings can cause serious problems that may prevent your computer from starting properly. Microsoft cannot guarantee that problems resulting from the configuration of the BIOS/CMOS settings can be solved. Changes to settings are at your own risk.

  Hope this information is useful. Please come back to write to us if you need more help, we will be happy to help you.

• Tecra S1: BSOD & reboot after installing SP2

  After installation of SP2 for Windows XP on three Tecra S1 of the computer crashes whenever the power cord is out of the machines. Then it restarts and restarts until the machine stops completely.

  The error ocures on three Tecra S1. It seems that there is a conflict with the pre-installed Windows XP Pro and the drivers Toshiba and SP2.

  Someone at - it an idea how to solve this very annoying problem?

  Thank you

  Chris

  Hello Chris,
  the SP2 blocking ActiveX Toshiba Management Console modules, so you must install the fixed version TMC v3.5.2.
  However, to avoid any problem, after installation of SP2 on Tecra S1, you need to update:
  -Battery BT and utility (only for machines with BT)
  Management - Toshiba console
  -Toshiba Hotkey utility
  Utilities - Toshiba
  Energy saving - Toshiba
  Toshiba - mobile extensions

• BSOD on reboot after installing the patch MS10-046

  I installed the critical patch MS10-046 on a netbook under XP SP3. On reboot, bsod with error message:

  "The Shell32.dll image is possibly corrupt. The header checksum does not match the checksum calculated. »

  The only way to start was via a USB key. I ran checkdisk (chkdsk/r) on the disc, and it found no errors. Then I copied an older version of the shell32.dll (from installation files) file in the system32 folder and could restart normally. I reinstalled the patch with the same result (bsod on startup), once again replaced the shell32.dll file. Automatic updates is asking to install the patch, but I don't do that until knowing what is the question. (It is set to download but not install).

  The system running Avira antivir personal, but I have another machine with XP and Avira and no problem.

  Any ideas?

  Your computer may have TDSS, a rootkit.

  This rootkit expected that some parts of Windows in certain locations in memory. When Microsoft released (MS10-046), the location of the core Windows API driver who depends on TDSS changed places. When a machine is rebooted to apply the fix, the rootkit tries to modify the memory that is no longer part of Windows target.

  Result? Blue Screen of Death.

  It's in the news just now:

  http://www.InfoWorld.com/t/Windows/Microsofts-patch-Windows-shortcut-flaw-has-limitations-822

• BlackBerry 9800 smartphones keeps restarting

  My 9800 torch keeps restarting and never started working. any help?

  You should consider the update/reinstall your device operating system. Check the KB article below-

  KB03621  How to recharge a device and software applications on the smart phone BlackBerry with BlackBerry Desktop Software

• BlackBerry Pearl Smartphones any reboots

  What happened at another time... It was my fault.

  This time it happened after auto-off during the night.  She never turned on in the morning.

  I took out the battery for a few minutes.  Put again and he came.  Except everything was gone...

  Very well, I supported TI... but then he did it again later in the day.

  Now he likes turns on during a few seconds... I see the screen and white with the hourglass then it turned off and the red light comes on.

  I can't go beyond that...?

  It's a Perle 8130

  Little help

  Thank you

  If it is not detected may have to try to reload the operating system in one of the following ways:

  1. http://www.BlackBerry.com/BTSC/KB03485
  2. http://BlackBerryFAQ.NET/index.php/How_do_I_wipe_the_BlackBerry_using _Jl_Cmder % 3F

• BlackBerry 8800 Smartphone unpredictable drains battery

  Hi, my 8800 seems to be on a full charge for a few hours, then it will quickly drop the fridge for an hour or two, up to 50% or less.  Sometimes, a night after a charge full in the afternoon, the 8800 is dead in the morning.  What he receives from one day to the next is our BES Server e-mail.  The hourglass cursor move too and turns off constantly.

  Only applications turning are browser, home page, record calls and Messages - which are empty.  Operating system is V4.5 (later).

  Someone at - he of the clues as to what might be causing this battery drain (I tried 3 different batteries, all the original BB brand)

  Thanks in advance.

  I suggest that you try the "battery 3 x in a row, charged 100% to each cycle of time" on one of the batterys. Read the link above.

  PS: BeamBerry worked very well for me.