BlackBerry MEP Code Z10 require for Z10

Similar Questions

• Smartphones blackBerry mep code is blocked

  Hello

  I have the bold 9650 unfortunately got hurt and enterd over mep code 10 times as result is blocked... now I'm worried wt to do I have hepatitis also lost his guaranteed card me plese help to find a solution simple and best...

  concerning

  After ten attempts have been used, you must get the RIM to unlock the device.

  There are two lanes and two only, to achieve this.

  * IF your unit is under warranty, contact your technical support service provider. Tell them that you have this problem that needs to be remounted at the RIM customer service level. I'll warn that most of the technical support people carrier assume first and think that you are talking about security of the release device, and you have to convince them of the contrary and explain clearly what you need. THEY will not be able to help you because the carriers themselves cannot unlock a device that had the code MEP attempts exhaustion and should (and you have to ask) to have the case escalated to a medium technical level RIM.
  * If your camera is out of warranty, contact directly the RIM. See the information to reach us from the Web site: http://ca.blackberry.com/contact/ the options that you want to select to talk to the BlackBerry customer service are 3 (for requests of information, orders, billing, e - RMA etc.) then 5 (e - RMA and warranty).

  Make sense? Good luck.

• BlackBerry Smartphones Mac OS required for Curve 8530

  Does anyone know what Mac operating system is required to link Curve 8530 an i - Mac using OS 10.4.11?

  Thanks a lot for any intervention on this issue...

  Bob.

  Check the system requirements for BlackBerry Desktop Manager for Mac - below

  • Mac OS X 10.5.5 or higher (only 32-bit mode is supported on Mac OS X 10.6)
  • BlackBerry® Device Software v4.2 or higher
  • Tunes v7.7.1 or later version

• BlackBerry Q10 remove PW required for unlocking phone

  Having to continually use a password from time to time to unlock the phone. Want to go back to NO password. How to reset the Q10 for this option?

  Now, I can answer my own question. Password requirement was caused by encrypting the data on the phone. Once I unencrypted data, the requirement of password could then be turned off.

• I get an error code, ""this device does not work properly because Windows cannot load the drivers required for this device. " (Code 31) "on the computer.

  My drive hard seagate is not recognized on my laptop, I can see it in the legacy of the laptop but has an exclamation deside it, there a message when I tried to solve the problems, error was not fixed, the device status is "this device does not work properly because Windows cannot load the drivers required for this device. (Code 31) »

  Is anyone know how can I access my hard drive again?

  Thank you

  Hello

  You has made changes to the system before the error appearing?  Cancel the changes.

  (1) in Device Manager > right click on the driver, and then select uninstall

  Reboot and Windows will reload the driver

  (2) remove the upper & lower filters that cause errors in Code 31

  http://pcsupport.about.com/od/driverssupport/HT/UpperFilters-LowerFilters.htm

  Access the manufacturer's Web site and search for updated driver

• Error of USB host - peripheral controller is not working properly because Windows cannot load the drivers required for this device. (Code 31)

  Original title - USB - IF xHCI USB Host Controller

  This device does not work properly because Windows cannot load the drivers required for this device. (Code 31)

  I have a permanent error on my computer and when I run the troubleshooter I get the above message.  It says Windows cannot load the driver.

  Hello

  USB devices remove all you can - restart the computer - is still there, the error? If it isn't
  It is related to one of the add-in devices that you removed. If she is still there, then, the question is
  either a device internal who can not remove or physically with the USB bus itself.
  If it was not there, add devices at a time until it is displayed - keep in mind that it is
  possible that there are two (or more) devices in conflict over the issue. Once you
  identified the check of the aircraft with the help of the manufacturer.

  1. to find the control panel - device - device - right-click on it - uninstall - Manager then
  Restart the computer to see if it clears.

  2. same place - double click on the device - driver tab - driver update - to see if that helps.

  3. check with the support of system manufacturer (manufacturer of motherboard for customized systems), their
  online documentation and drivers, diagnostics and ask questions in their forums on all known
  questions. Update the Bios and chipset or other USB drivers.

  =====================================

  If necessary, we will use these additional troubleshooting methods:

  How to fix Code 31 errors
  http://pcsupport.about.com/od/findbyerrormessage/a/code-31-error.htm

  I hope this helps.

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle=""><- mark="" twain="" said="" it="">

• My crashing after windows loading and I have this message - this device is not working properly because Windows cannot load the drivers required for this device. (Code 31)

  This device does not work properly because Windows cannot load the drivers required for this device. (Code 31)

  Hello

  Have you tried to update the drivers as suggested by Basith M?
  
  Method 1:
  You can run the fix provided in the link and check out them.
  Hardware devices do not work or are not detected in Windows
  http://support.Microsoft.com/GP/hardware_device_problems

  
  Method 2:
  You can also try the procedure described in the link to troubleshoot driver issues.
  Tips for solving common driver problems
  http://Windows.Microsoft.com/en-us/Windows-Vista/tips-for-fixing-common-driver-problems
  
  See also the proposal contained in the link and check.
  On a Windows Vista-based computer or on a Windows Server 2008-based computer, the Microsoft ISATAP map appears with a yellow exclamation mark next to it in Device Manager, and you also receive an error message
  http://support.Microsoft.com/kb/932520/en-us

• Installation of Windows Vista disc will not re - install. "files required for installation are not available" error 0x8007045D code

  My computer is slow, so I decided to format the C drive and re - install Vista with the installation disc. I did it once before and it worked. This time, however, I tried to install it and once he got to the 'Copy files' section and "Expanding files" error message came up saying: "Windows cannot install required files. Make sure all files required for installation are available, and restart the installation. Error code: 0x8007045D

  I tried to restart the computer, and restart the installation, but nothing does.

  I need your help please!

  It's an IO error.  Try to wipe the dvd with a soft cloth and then try again.  The drive itself may also need cleaning.

• Upgrade Vista to Windows 7 error: "Windows cannot copy files required for installation. The files may be damaged or missing. Error Code Ox80070017.

  I am upgrading of Windows Vista Home Premium (32-bit) for Windows 7 Home Premium (32 bit) - but getting stopped everytime I try, I end up with a dialog box stating: "Windows cannot copy files required for installation. The files may be damaged or missing. Make sure all files required for installation are available, and restart the installation. Error Code Ox80070017.

  What should I do to resolve this problem and allow full of Windows 7 installation? (my computer is a Compaq Presario V6000).

  Hello

  What installation media you are using?

  Method 1:

  Error 0 x 80070017 translates "CRC error" which means that the files that are copied from the disc are not making it to the hard drive with the same structure, which means that the 'original' the disk files are modified/changed/corrupted while being copied to the location of the 'destination' on your disk during Setup.

  This usually means a bad DVD, or an error reading on the DVD player.

  I suggest you follow the link and check.

  Upgrade Windows Vista to Windows 7

  http://Windows.Microsoft.com/en-us/Windows7/help/upgrading-from-Windows-Vista-to-Windows-7?T1=tab02

  Method 2:

  Temporarily disable the antivirus on the computer running software and check if you are able to install the software.

  Disable the anti-virus software

  http://Windows.Microsoft.com/en-us/Windows-Vista/disable-antivirus-software

  WARNING: Antivirus software can help protect your computer against viruses and other security threats. In most cases, you should not disable your antivirus software. If you need to disable temporarily to install other software, you must reactivate as soon as you are finished. If you are connected to the Internet or a network, while your antivirus software is disabled, your computer is vulnerable to attacks.

  Enable or disable Windows Firewall

  http://Windows.Microsoft.com/en-us/Windows-Vista/turn-Windows-Firewall-on-or-off

  WARNING: There may be loss of data through an analysis using firewall to eliminate the virus as appropriate

  Method 3:

  I also suggest you to follow the link and check.

  Check your hard drive for errors

  http://Windows.Microsoft.com/en-us/Windows-Vista/check-your-hard-disk-for-errors

  Important: When running chkdsk on the drive if bad sectors are found on the disk hard when chkdsk attempts to repair this area if all available on which data can be lost.

• This device does not work properly because Windows cannot load the drivers required for this device. (Code 31)

  Original title: this device does not work properly because Windows cannot load the drivers required for this device. (Code 31) in graphics AMD - 8151 HyperTransport (MC) AGP3.0 Tunnel

  This device does not work properly because Windows cannot load the drivers required for this device. (Code 31) in the graphics AMD - 8151 HyperTransport (MC) AGP3.0 Tunnel, what do I do to fix this help please.

  Jake

  Hey Jake,

  Follow these methods.

  Method 1: Follow these steps:

  (a) restart your computer if you have not already done so. There is always the possibility that the error Code 31 that you see was caused by a temporary problem with Device Manager. If so, a simple reboot can solve the Code 31.

  (b) have you install a device or a change in the Device Manager, just as the Code 31 error appeared? If so, it is very possible that the modification caused the Code 31 error.

  (c) cancel the change if you can restart the computer and then check again the error Code 31. Depending on the changes, some solutions may include:

  Remove or reconfigure newly installed unit.

  Restore a version prior to updating the driver.

  Use system restore to undo the Device Manager recent related changes.

  http://Windows.Microsoft.com/en-us/Windows-Vista/system-restore-frequently-asked-questions

  (d) to remove the registry values filters upper and lower. A common cause of errors in Code 31 is the corruption of two registry values in the class of the CD-ROM/DVD-ROM drive registry key.

  Note: This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click the following link. http://Windows.Microsoft.com/en-us/Windows-Vista/back-up-the-registry

  Method 2: Update the latest graphic drivers.

  Updated a hardware driver that is not working properly

  http://Windows.Microsoft.com/en-us/Windows-Vista/update-a-driver-for-hardware-that-isn ' t-work correctly

• Computer does not recognize network. -This device does not work properly because Windows cannot load the drivers required for this device. (Code 31)

  Hello!

  I have problems connecting to my network. I stay in a House (not my own) and I can't connect to the network in this House. When I choose the option 'connect to a network', nothing happens. I followed the instructions to display the "Device Manager" and watch the 'map', and he said:

  "This device does not work properly because Windows cannot load the drivers required for this device. (Code 31)

  Click on 'Search for solutions' to send data about this device to Microsoft and to see if there is a solution available. »

  When I click on this button, nothing happens... Should I simply wait for Microsoft to return to me - or is there something else I need to do?

  Thank you!

  Hello

  You must get the drivers latset for m computer support site.

  Delete the "false: entry in Device Manager and install the new drivers."

  Jack-MVP Windows Networking. WWW.EZLAN.NET

• Huawei Mobile Connect 3 G Modem this device does not work properly because Windows cannot load the drivers required for this device. (Code 31).

  System: Windows 7 Ultimate 64-bit. QC processor 2.5 Ghz, 4 GB RAM, Nvidia 9600GT. The work of modem very well until about a month. Uninstalles the device, I reinstalled it but the same messages. I've updated the driver and software, still nothing. In safe mode, the modem driver is loaded and the devicemanager reports that the device is functioning properly. Once the system is booted in normal mode divcemanager reports: this device does not work properly because Windows cannot load the drivers required for this device. (Code 31). Help, please. I check the settings for the 6to4 drivers and there is no problem.

  Thanx

  Hi rui2010,

   

  Place your machine in a clean boot State to see if another application is in conflict with the modem.

  If this fails, I recommend you reach out to the community Hauwei for assistance:

  http://Forum.Huawei.com/jive4/Forum.jspa?forumid=46&orderStr=9

   

  Aziz Nadeem - Microsoft Support

  [If this post was helpful, please click the button "Vote as helpful" (green triangle). If it can help solve your problem, click on the button 'Propose as answer' or 'mark as answer '. [By proposing / marking a post as answer or useful you help others find the answer more quickly.]

• BlackBerry App Facebook Z10 questions

  I had a job for years facebook app and I don't have much to complain, but now there's a lot going on with the app that I don't get. After updating the app, I was not able to use it. Now, acting as a kind of shortcut for my browser, calendar, and contacts Facebook, hub is gone and it is now useless as it is now a browser shortcut. How to fix, it downgrade to the previous or how long should I wait for an update that works?

  Exactly, the Facebook for BlackBerry app has been disabled due essentially to the fact that Facebook will not allow access to what is called the BlackBerry Facebook API. Fault of Facebook and the decision. BlackBerry has created the browser shortcut.

  Details here: update required for Facebook

  There is a solution to your Facebook contacts on the device BlackBerry10: How to get Facebook on BB10 contacts

• Windows cannot copy files required for installation. The files may be damaged or missing. Error code: 0 x 80070241.

  I had a lot of trouble trying to install the 64-bit version of windows 7 Home Premium on my 64-bit vista, and my question is multi-part. If it is relevant, it's my 2nd copy of windows 7 I have tried. Initially, I had the problem of not being able to run the installation on two copies with the error "'autorun.dll' could not be found or is damaged. Error code is [0x7E]. "However, I managed to get into with my 2nd copy installation after restarting my computer. Once in Setup, I got another error that stopped the installation that says "windows not could create an installation folder. Error code is 0 x 80070017. "Again, I rebooted my computer and started the installation again, this time following installation was decently through but stopped when I got the error"Windows cannot copy files required for installation. The files may be damaged or missing. Error code is 0 x 80070241. "I then backed up and restarted my computer and then tried to use the option to install custom but then got the error"E:\sources\autorun.dll is not designed to run on windows or it contains an error. Try to install the program using the original media, or contact your system administrator. "coupled with the error"the file 'autorun.dll' could not be loaded or is corrupt. Error code is 0xC1"again once I restarted and tried the custom option but got the error" Windows has no load the required file WinSetup.dll.» The file is possibly corrupted. To install windows, restart the installation. Error code is 0x3E6. "I restarted my computer and tried the custom triple option more and still have the error"Windows cannot copy files required for installation. The files may be damaged or missing. Error code is 0 x 80070241. »

  I understand that my problem is very complex, but it seems to be built around a missing or damaged file. Thanks if you can tell what's wrong or what to do.

  Tips for solving common problems when Windows 7 won't install troubleshooting

  1. start Windows Upgrade Advisor to see if there are known issues that might affect the installation and correct them.
  http://Windows.Microsoft.com/en-us/Windows/downloads/Upgrade-Advisor

  2 disable any security software, including anti-virus programs and firewalls.
  3 make sure that your computer has the BIOS and latest drivers.
  4. disconnect all external devices except the keyboard and mouse before installing.
  5. If your computer/motherboard integrated video use and remove the dedicated video card.
  6. If you have a large amount of RAM (memory), try to reduce the amount of RAM installed. 1 GB if 32-bit installation, 2 GB for 64-bit, then replace RAM if the upgrade was successful.
  7. If you have downloaded Windows 7 and it burned a DVD test burn again at the slowest speed possible. It is also possible the download may have errors, you can try to download it again.

  8. check your RAM (memory) to find errors. This can take some time.
  (A) Insert the Windows 7 DVD and restart the computer.
  (B) start from the Windows 7 DVD.
  (C) select your language, and then click Next.
  (D) click on "repair your computer" then select the operating system to fix it.
  (E) click on the link of the Memory Diagnostics in the system recovery menu.
  (F) the computer will restart and your memory is checked for errors.

  9 turn off startup programs:
  (A). Click Start, type MSCONFIG in the search box and press ENTER.
  OK the authorization of user account control and password if necessary
  If you are using XP: click Start, run, and type: MSCONFIG and click OK.
  (B) on the general tab, click Selective startup.
  (C) just below the selective startup, clear the checkbox "Load Startup items".
  (D) click the Services tab, check "Hide all Microsoft Services", and then click Disable all.
  (E) click OK, and then restart the computer.
  (F) try the upgrade again.

  (NOTE: If the upgrade fails and you continue to use your rear security software, then also go back into MSCONFIG and under the general Tower XP/Vista tab, click "Normal startup", and then click OK to exit.)

  Questions about installing Windows 7?
  FAQ - Frequently Asked Questions from Installation Windows 7 & responses

• BlackBerry Blackberry Balance on my Blackberry Limited Edition Z10 Z10

  Hi all

  How can I use my Blackberry on my Z10 balance?

  I think that I didn't have the balance of Blackberry on My Z10.

  Best regards

  Richard Kesuma

  Your BB10 device must be enabled on a server (Blackberry Enterprise Service) BES10 in order to have some balance BB.  It is not available otherwise.  If you are on a BES10 service from your company, see scientists responsible and let them know that it does not work on your device.