Blank beeps

Similar Questions

• Satellite U400 - screen is blank and gives a beep

  Hello

  I tried to turn on my laptop and the screen is just blank, battery is fine all LEDs light up but it does not start. It beeps every 2-4 minutes.

  Some can help or advise please

  Hey,.

  Generally these codes beeps mean that a hardware malfunction has been detected if you changed something on the hardware configuration?

  If you have installed both memory modules, you must test it with the single module only. Sometimes it happens that the RAM modules are faulty then try it with a module only. Maybe it helps :)

• Blank screen, no beeps or error codes.

  HI I have a HP 2000 nopebook PC and its gives me a black screen no beeps or error codes. I can hear the sounds of start-up and see the screen illuminates upward and then darkens. When I plug in an external moniter happens.  I tested the memory, the inverter, I tried to drain the battery and even tried to update the graphics card and still nothing.

  Help, please!

  Yes! You are right. The laptop did work normal without any problems, but your laptop screen has gone bad and needs a replacement. HP will provide a screen for your laptop of replacement if warranty is active, you can check your warranty here to check the status

  Hope this helps, for other queries in response to the post and feel free to join us again

  * Click on the star of CONGRATULATIONS on the left to say thank you *.

  Make it easier for others to find solutions by checking a response "Accept as Solution" if it solves your problem.

  Thank you

  K N R K

  Although I am an employee of HP, I speak for myself and not for HP

• strange monitor beep sound and blank when I installed the graphics card XFX Radeon HD 7870

  OK, so I removed my GTX 555 after that I bought a brand new XFX HD 7870, installed and activated on the pc.
  The monitor was empty and the pc tower was 5 beep sounds, then pause and repeat, over and over again until I turned off. When I replaced the GTX 555, all was well again, so I know this isn't the other components.
  Any suggestions?

  See http://products.xfxforce.com/en-gb/Graphics_Cards/AMD_Radeon%E2%84%A2_HD_7870/FX-787A-CDFC.

  You will need an adapter and you may need a new power supply.  Note the minimum requirement of the PSU of 500w.

• HP Z620 workstation: HP Z620 Workstation - WS displays video & Fans Spin loudly or fails - red light with 8 beeps

  Hello
  
  I have a HP Z620 workstation.

  My processor is an Intel Xeon E5-2660 SR0KK 2.2 GHZ 20 MB 8 GT/s LGA 2011 8 - Core CPU.  More correctly, it's a category of Xeon E5-26xx (dual processor), 8 cores, frequency 2.2 GHz, turbo 5/5/6/6/7/7/8/8, 8 × 256 KB L3 cache 20 MB L2 cache, 95 W TDP, Socket LGA 2011, i/o bus 2 × 8.0 GT/s QPI, × 4 memory DDR3-1600, release date 6 March 2012, CM8062107184801 part number.  This is version 1, not version 2, which is good because the card in my system startup block date 20/12/2011.

  I am using Kingston ValueRAM 16 GB Kit (2x8GB) DDR3 1333 MHz DIMM Desktop Server Memory.   (J'ai également essayer écarter un problème de mémoire utilisé FUREUR de Kingston HyperX 8 GB Kit (2x4Go) 1333 MHz DDR3 CL9 DIMM - black (HX313C9FBK2/8)) as well as herself, to see if that makes a difference.)

  I don't know how to identify my system board other than the one she reads only numbers as "FMB-1102" and "PBLNV0GCY4N0TF" and "such as #618264-001 REV 0 G'.  He has "hp (copyright symbol) 2012 ' and"E93839"and"FXN1"written on it as well.  (After some searching I guess it's card mother 618264-001.  Which differ a card system like 619559-001 - a model later?)
  
  My graphics card is a XFX R7 240 780 MHz 4 GB DDR3 HDMI DVI VGA graphics card.  (I also try out a video card problem used an EVGA Nvidia GeForce GT 620 1 GB DDR3 SDRAM PCI Express 2.0 x 16 video card to see if it would make a difference.)
  
  Regarding the power supply, the power supply standard HP Z620 computer PC 800W Power Supply S10-800P1A 623194-002 717019-001.  (I have more than one and who have tried also.)

  With respect to the hard drive, I have formatted and reused a WD Blue 500 GB Desktop hard drive - 7200 RPM SATA 6 Gb / s, 16 MB Cache 3.5 inches - WD5000AAKX.

  My problem:

  1 regardless of what video card I use, if I use the FURY of Kingston HyperX 8 GB Kit (2x4gb) 1333 MHz DDR3 CL9 DIMM - black (HX313C9FBK2/8) memory and starts, I get a blue light, no beeps, no code of message I can say.  However, no tension of the video card (fans not spin) and no power is supplied to the drive hard (do not load and run).  I get a blank screen and can see nothing.  Back fans begin to turn in very strong and turbo mode.

  2 regardless of what video card I use, if I use the Kingston ValueRAM 16 GB Kit (2x8GB) DDR3 1333 MHz DIMM Desktop Memory Server, I get a red light and eight beeps which means a kind of ROM BIOS/CMOS-problem problem problem.  To this end, I tried pressing the button Clear CMOS without result.  I removed the CMOS battery for a sufficient period of time and again.  Nothing changes this situation.  It only happens when I put this special memory in the computer.  If I stick a USB Thumb Drive with file BIOS (BIN) in it which is 3. XX or higher, it will boot to the BIOS on a limited basis.  I also had to understand that I couldn't do anything with a USB keyboard, I could only select options using a PS/2 keyboard - maybe it crashes on some USB devices at this point?

  3. I understand that if I let the rider of recovery from crisis on the 2nd and 3rd pins rather than pins 1 and 2, that it will load from a backup and I can actually do things.   On this basis, I was able to install Windows 10 education 64-bit and a host of programs and otherwise, use the computer normally.  But I can't start unless I have keep that crisis rider of recovery set to pins 2 and 3 and so he can start in the operating system normally by pressing F1.

  4. I while on Windows, updated the BIOS to the latest version, HP Z420/Z620 Workstations system BIOS 3.90 Rev.A (August 8, 2016) using sp77058.exe (19 MB).  I've also updated other drivers as I could with the HP SoftPaq Download Manager (SDM).  None of this changes the problem at initial boot upward.  At the start he complains front chassis fan does not turn, but this is not a problem I have printing allows to stop a boot to the top, it would give just a warning and still boot normally.

  Well my computer works and does that as long as I keep this crisis recovery jumper on.  But I feel that I should be able to solve the problem and he can begin without interference and without resorting to a measure as drastic.  Suggestions anyone?

  Thanks in advance for your time.

  MR. J.

  Juggerknight,

  Keep the rider of recovery of block starting on pins 2 and 3 of E15.  It's 'off' because the 3 pin is not connected.  Put the jumper to pins 2 to 3 "parks" the rider.  Put the jumper on pins 1-2 active boot block recovery mode, and the system does not start with the jumper in this position 'on '.  (You have already discovered this)

  In addition, do not mix unbuffered and registered in the same system memory.  Use either one or the other.

• Satellite Pro 6100 - code beep at startup

  Hi all

  Just picked up a 6100 Pro of the Satellite with a few problems.

  It lights up, he pointed out the HARD drive and I can hear the disk activity. However, the screen remains blank and a single beep can be learned after 20 sec. White screen, as I understand it, is probably the issue of Council power raging in the SP6xxx series. However, the beep I do not understand.

  I know that 2 beeps or 3 beeps is incompatibility of memory but no one knows which denotes the beep?

  Ta

  Hey Buddy,

  To be honest it's not easy to say what the cause of the problem because it could be everything and Satellite Pro 6100 is old enough for laptop.

  You have two memory modules RAM? If so remove a module. Always try a module only at the same time and test it in the slot of RAM A and B. A module is may be defective or a slot.

  If this is not the case, there seems to be a problem with the motherboard or the CPU itself. If you can exchange these things, try it yourself as a repair would be too expensive for this good old classic I think.
  Second hand spare parts you can get it on eBay s worth a try! ;)

• Annoying beep of Satellite P10 873

  Hi, im this annoying beep intermittently from my toshiba, ive had more than 3 years and over the last 3 months or so this started beep to sound.

  It looks like a number being pressed on a pad of phone, very loud sound and the most annoying numbering and occurs randomly.

  Some days I don't hear it at all.
  I searched on through all the settings for modems, and system sounds.

  Control Panel and programs to no result and ive heard when nothing is connected to the pc to avoid externel gadgets

  Also I searched this problem a few times and there is no apparent answer, my supermulti drive cannot read CD more but it can burn, it is said that every cd I put in that is a blank CD - r, it reads the dvd but cannot burn DVDs and it will not read ram dvd more all solutions outside a new drive?

  It looks like a serious hardware issue... you spilled some liquid top? Such a sound comes from a key that is pressed constantly, this may also occur when keys are stuck because of some dirt in the keyboard or liquid that has dried and is today a sort of 'super-key-glue' that allows keys get stuck.

  Did you notice that some keys are "suspended"?
  Regarding your disk: have you ever tried a few updated firmware? And this is surely more interesting: what programs burning or cd player for the applications you have installed?

  welcome them

• New installed graphics cards makes beep sound and no response from the monitor

  Hello.

  I have a hp pro 3300 micro Tower. I installed a new card from nvidia quadrophonic 420 graphics.

  When I start the pc I hear 4 beeps and then nothing. The screen is blank

  eager to help

  D

  Hello:

  4 beeps is a problem with the power supply.

• 3 beeps on startup satellite A200

  Hello

  I have a Satellite A200 E-530 (Core2duo T5300) began to my laptop went blank when turn on and it emits 3 beeps and a few beeps 2 times. I have check the Rams are quite good.

  I found that the cpu fan is not moving and turn it on and sometimes the fan will start to move slowly until some time the fan will spin until it goes to full speed and when I turn and turn the beep disappear and the laptop back to normal.

  But after a few days and never happens again anywhere.

  Some experts may give some ideas what is happening on my laptop, it is about 3 to 4 years of age.

  Thank you

  Have you ever cleaned?
  Your laptop is hot after a short period of time?

• Equium A60 will not start - get a beep code

  Hello

  This laptop has problems with ATI (even those included on the recovery disk) display drivers. He created a blue screen on a dll file.

  After reading around, I found that it was recommended to upgrade the bios, after going to the appropriate section of the Web site, I downloaded the flash tool from windows for the laptop bios.

  I ran and it opened, returned to the laptop and the screen is blank, a blue ring around the power button is on, but no display.

  I left it for a period of time see if it would to restart or something, but nothing has happened, it would not be the button turn off so I unplugged the power and removed the battery.

  To again turn on the laptop, it only stays on for about 3 seconds then turns off again.
  I get the beep code: short break, Long, short break, beep, beep beep, then it turns off.
  The caps lock and numlock keys are turned on.
  The DVD drive light blinks.

  But other than that, no display etc.
  Ive tried the battery leaving aside for awhile.

  Anyone have any ideas why flash bios toshiba own this would cause? Also what can I do about it? in any case to recover the bios etc via a recovery mode?

  Thanks in advance.

  PSA67E

  Hello

  Well, unfortunately for me it looks like a hardware failure.
  Maybe the motherboard is broken.
  These problems may occur if you use a bad BIOS or the incorrect BIOS update procedure.

  Please check this document FAQ How to upgrade the BIOS:
  IOS http://eu.Computers.Toshiba-Europe.com/cgi-bin/ToshibaCSG/FAQ.jsp?z=234&service=eu&from=faq_selection&CFID=B & FID = TRO0000000b07

  Unfortunately if there is something wrong with the hardware you should ask Toshiba service for assistance.

• Error beeps

  I've had my Touchsmart 11 for about 2 years now. Never any problems. Over the last month or so most of the time when I start it, it gives 3 beeps long, followed by 2 short beeps. It is this sequence 3 times and will not start. The screen remains blank. I tried searching the Internet, but did not find the corresponding sequence of beeps anywhere.

  It's very annoying. I must repeat that a few times before it finally starts.  Sometimes I have to do 6, 7 0r 8 times before starting. The sequence is exactly the same 3 long beeps, 2 short beeps and it happen exactly 2 times more. I haven't added any software or devices in the system.

  Would appreciate any input on this.

  Hello @amin00,

  Thank you for posting!

  If you still get the ringtone, even after the relocation and replacement of the strip of memory, then you can consider contacting the HP support by phone for additional options.

  Please use the following http://www.hp.com/contacthp and create a folder for your question and contact HP. If you do not live in the United States / Canada, please click on the link below to get contact information for your region.
  http://WWW8.HP.com/us/en/contact-HP/WW-phone-assist.html

  Good luck!

• Lenovo M91p desktop does not boot with the new graphics card (Blank don't screen no BIOS)

  Hi all

  I recently bought a Lenovo M91p thinkcenter Desktop as an upgrade to my old PC i3.

  Old Spec is as follows:

  • Coolermaster Thunder 600W power supply
  • Card mother Intel DH55HC
  • Processor i3
  • Graphics HIS HD Radeon 7950
  • 8 GB RAM
  • HARD DRIVE 500 GB

  I transferred my HD supply and Power 500 GB old to new Lenovo desktop and everything starts very well.

  Then I installed 2 x 2 GB extra in the Lenovo M91p (which in fact 8GB) and updated the disk of 500 GB to 1 TB.

  So my new spec is as follows:

  • Coolermaster Thunder 600W power supply
  • Card mother Lenovo Q67
  • I7 2600 3.4 Ghz CPU
  • 8 GB RAM
  • 1 to and 500 GB HARD drive

  Everything Booted fine. Then I tried to install my old graphics (HIS 7950 graphics Radeon HD card) card. I got was a blank screen, no beeps, no BIOS... Nothing.

  At first, I thought that my diet was not enough... So I tested a 750W power supply in the pc. Still nothing.

  Then I thought that the motherboards BIOS was outdated... Updated... Still nothing. I even tried to update the firmware of the graphics card. Nothing.

  The graphics card works because I tested it in my old machine and it worked 100%.

  However, I took my graphics card to my provider and he tests it on another of his pieces... Did not work there either.

  My PC BIOS is not supported for secure boot, in case anyone wants to know.

  I am out of ideas now... Anyone able to help?

  There is a white list of graphics cards that will recognize the BIOS. The 7950 HD is a map of 180w, well beyond what the power plant can provide (and case/sufficient cooling fans for) and not a single one is that Lenovo would provide support for the BIOS.

  Use the search engine above to see what cards other owners have used successfully in their M91p.

• DV8210us won't start no-4 beeps

  I have a HP Pavilion DV8210us.  I press the power button.  The buttons light up.  The screen is blank.  I hear 4 beeps constantly.  The system is out of warranty if HP was no help.  Any help would be appreciated!

  try to remove a memory module (the smallest) and beginning of pressing for a test. If it starts... Large. If this isn't the case, test the other stick in the same way.

  Best regards
  ERICO

• four beeps at startup

  I have an old laptop R50e of 3.5 year are no longer under warranty.

  When I boot it battery or power, I get four regularly spaced beeps and nothing else. The screen is blank and the fan is running. This happened this morning. I had used last yesterday evening and gracefully close.

  Thanks in advance for any help.

  zekela, welcome to the forum,

  According to the hardware maintenance manual for your R50e, (pdf p.74), four short beeps and an average of the white screen that your motherboard is dead. You find all error descriptions in the manual.

• I get a blank screen just before the connection with a single visible cursor

  Currently, my computer will load where the login screen should appear, but instead merely display a white screen with the mouse cursor in the middle that I can move around.

  I tried restoring the system manually at a point in time that he began to arrive. That did not work. I tried a restore of the system manually to a time past, does not work well before it began. I tried to have my computer to do in the repair option to "restore to the last known good configuration" and that did not work. I ran various programs that look for malware, spyware and viruses many times and found a few things, but nothing of this has solved the problem. I tried to check all my drivers and they say all work and all drivers say they do not need an update. I tried the system repair tool and he found nothing wrong, even with the memory to check tool that finds nothing wrong. If I press SHIFT 5 times to the white screen with the cursor, I'll hear the keys to self-retaining beep, but no prompt.

  One thing that happened was that I was once in the blank screen and I pushed to escape and I noticed that the cursor has turned to an hourglass. Then I tried Ctrl alt delete and which opens a command prompt and from this command prompt it allowed me to go to the usual login screen. Then, my computer work as it did just before this problem (a warning would pop-up Windows saying that it stopped a program that you try to start itself without permission and who would be come like every minute or so). But since then I havnt been able to reproduce this same result to load or by opening the command prompt.

  And safe mode works very well.

  I was reading around online and there was something that said they had the same problem and download internet explorerer 7 helped. as well as a similar problem which was fixed when IE8 was downloaded an update of windows. the guy deleted and it was fine since.

  I tried to download the latest version of Internet Explorer, but it cannot be loaded without rebooting, and I can't enter the normal screen that opens after the cut to finalize it. I always still try to remove it as well as the update of windows.

  Another difference I noticed is in the loading bar than before windows starts as the login screen. It used to be thick green blocks that crossed with the windows logo. Now, it's a block really thin yellowish green (which reminds me of the life blocks Mega Man in his health bar if that helps lol) and no windows logo because it does it (if it says copywrite along the bottom windows corporation).

  If anyone has more aid in addition to the info windows give a repair tool, please help. Thank you.

  Hi chase11,

  Support for Windows Live One Care stopped if you need to uninstall it and move to another antivirus/antispyware/security protection. OneCare online scanners are always available.

  Here the Site of OneCare Live:

  http://OneCare.live.com/standard/EN-US/3/default.htm

  Help and Support
  http://OneCare.live.com/standard/EN-US/3/helpsupport/default.htm

  Use the methods of uninstalling suggested here or by Windows Live OneCare.

  List of tools to clean/uninstall anti-malware programs
  http://answers.Microsoft.com/en-us/protect/Forum/protect_start/list-of-anti-malware-program-cleanupuninstall/407bf6da-C05D-4546-8788-0aa4c25a1f91

  How to uninstall Windows Live OneCare
  http://OneCare.live.com/standard/en-us/install/uninstall.htm

  See also this thread for more information about uninstalling Windows Live OneCare - it is a
  chore however it must be done.
  http://social.answers.Microsoft.com/forums/en-us/msestart/thread/407bf6da-C05D-4546-8788-0aa4c25a1f91/

  ===============================================================

  Here's what I use and recommend: (these are all free and very effective versions.)

  Avast and Prevx proved extremely reliable and compatible with all I have
  launched on them. Microsoft Security Essentials and Prevx have also proven to be very
  reliable and compatible. Use MSE or Avast and Prevx, Prevx 3 but not all.

  Avast Home free - stop any shields is not necessary except leave the file system, Web,.
  Operational network (Script and behavior are also recommended in Ver 6 +).

  Prevx - Home - free

  Windows Firewall

  Windows Defender (is not necessary if you use MSE)

  Protected IE - mode

  IE 8 - SmartScreen filter WE (IE 7 phishing filter)

  I also IE always start with asset if filter InPrivate IE 8.
  (It may temporarily turn off with the little icon to the left of the + bottom
  right of IE)

  Two versions of Avast are available 6.x and 4.8 x

  Avast - home - free - 6.x stop shields you do not use (except files, Web, network, &)
  Shields of behavior) - double click on the icon in the Notification area - real time Orange - click on the
  Shield that you want to stop - STOP. To stop the Orange icon to show an error indicator-
  Click on the Orange icon - top right - settings - click on the status bar - uncheck shields you
  disabled - click OK
  http://www.avast.com/free-antivirus-download

  Avast 4.8 x - home - free - stop shields, you don't need except leaving Standard, Web,.
  and the network running. (Double-click the blue icon - look OK. - upper left - Shields details
  Finish those you don't use).
  http://www.avast.com/free-antivirus-download#TAB4

  Or use Microsoft Security Essentials - free
  http://www.Microsoft.com/Security_Essentials/

  Prevx works well alongside MSE or Avast

  Prevx - home - free small, fast, exceptional protection CLOUD, working with other security
  programs. It is a single scanner, VERY EFFICIENT, if it finds something come back here
  or use Google to see how to remove.
  http://www.prevx.com/   <-->
  http://info.prevx.com/downloadcsi.asp  <-->

  Choice of PCmag editor - Prevx-
  http://www.PCMag.com/Article2/0, 2817,2346862,00.asp

  Also get Malwarebytes - free - use as scanner only. If you ever think malware and that
  would be unusual with Avast and occasional Prevx running with the exception of a low level cookie
  (not much), to UPDATE and then run it as a scanner. I have a lot of scanners and they
  never find anything of note that I started to use this configuration.
  http://www.Malwarebytes.org/products/malwarebytes_free

  I hope this helps.

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle="" -="" mark="" twain="" said="" it="">