Blue screen after startup

Similar Questions

• Satellite L300D c000021a (PSLC8E) blue screen on startup after win7 64 bit

  Hello

  The error code on a blue screen after startup (after loading win7 logo) is:
  STOP: c000021a {fatal system error}

  Installed Win7 Ultimate x 64.

  My bios version is 1.80

  Someone has any idea how to solve this problem?

  Thanks for help

  Have you tried to install the original preinstalled Toshiba system using the recovery disk to check if the same BSOD error appear?
  If this is not the case, do.
  This BSOD can be linked either hardware or software problem and good work and pre-configured system could clarify the situation.

• Pavilion DV6 3055tx blue screen after RAM Upgraderei

  The product name and number: HP Pavilion dv6 3055tx

   

  Pre-installed RAM: 3 GB
  

  Operating system: Windows 7 Home Basic 64 Bit (90 days)

   

  Error message (if any): blue screen on startup of the BONE
  

  All changes to your system until the problem occurred: RAM upgrade

   

  In the title of the topic, include a brief and accurate description of the problem and your product information: I use this product for a long time... Good...

   

  One day, I thought to upgrade my RAM, so I ordered "CRS 4 GB LT_CMS04GX3M1A1600C11"

   

  Corsair 4 GB DDR3 RAM simplified eBay India

   

  After I received the product, I open the back panel and removed the 1 GB RAM Samsung and Corsair inserted one I ordered.

   

  After this, I restarted my system

   

  When starting Windows came to loading blue screen suddenly comes and laptop restarting

   

  Then a black screen comes with 1. Launch the tool to restart System 2. Start Windows normally

   

  I gave my chance for both, but the same blue screen.

   

  After that, I removed the two Rams and inserted as a single Corsair

   

  Same blue screen

   

  Then I open BIOS and it says 4096 MB installed memory

   

  After that, I inserted the 2 GB with it means Total two-channel 6 GB

   

  But again Blue Screen and BIOS saying 6144 MB

   

  What is the problem?

   

  Please help me solve the problem.

   

  The eBay seller is ready to replace the RAM, but I want to know if this could be a compatibility issue.

   

  Thank you... Waiting for a good answer

  Hello:

  I can't find any specs on that you bought it from memory.

  Your PC will run from 8 GB of memory, but you must be careful as to what memory you select.

  You must get the PC3-10600 (1333 MHz) memory and it must be of low density.

  You can't get PC3-10660 or PC3-10666 memory and cheap will be high density and will not work in any case in your laptop.

  You can see this related posts with someone who had the same problem, and when he bought the good memory, his problem was gone.

  http://h30434.www3.HP.com/T5/hardware-upgrades-replacements/dv6t-3000-RAM-upgrade/m-p/2492127#M17965

  I think you bought PC3-12800 memory and this is probably the high density - two bad things.

• Get blue screen after Windows KB968389 updates

  I got the blue screen after that almost each update of Windows, but later is the following:

  Internet Explorer 8 for Windows Vista for x 64-based systems (25/08/09)
  Update for Windows Vista for x 64-based systems (KB968389) (11/08/09)

  I have a new Dell laptop Studio 15.  Do the system restore still does not work, or do not put the machine in Mode without failure.  I'm tired of spending hours trying to get my machine up and running

  Hello

  Certainly Support Dell help you change things anymore they can claim it was something
  you did it.

  Dell support
  http://support.Dell.com/

  Dell forums
  http://en.community.Dell.com/forums/

  My thoughts are that it is a driver problem. Try to update your drivers, and then stop the updated driver in Windows Updates.

  -----------------------------------------

  This is my generic how updates of appropriate driver:

  For drivers, visit manufacturer of emergency system and of the manufacturer of the device that are the most common.
  Control Panel - Device Manager - Display Adapter - note the brand and complete model of your
  video card - double - tab of the driver - write version information. Now click on UPdate Driver (this
  cannot do anything as MS is far behind the certification of drivers) - then do a right click - Uninstall - REBOOT
  This will refresh the driver stack.

  Repeat this for network - card (NIC), Wifi network, sound, mouse, and keyboard if 3rd party with their
  own the software and drivers and all other main drivers that you have.

  Now go to the site of the manufacturer of system (Dell, HP, Toshiba as examples) (restoration) and then of the manufacturer of the device
  (Realtek, Intel, Nvidia, ATI, for example) and get their latest versions. (Look for the BIOS, Chipset and software)
  updates on the site of the manufacturer of the system here.)

  Download - SAVE - go to where you put them - right click - RUN AD ADMIN - REBOOT after each installation.

  Always check in the Device Manager - tab drivers version you install actually shows up. This
  because some restore drivers before the most recent is installed (particularly that audio drivers) so install a
  pilot - reboot - check that it is installed and repeat if necessary.

  Repeat to the manufacturers - BTW on device at the DO NOT RUN THEIR SCANNER - manually check by model.

  Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
  http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htm

  How to install a device driver in Vista Device Manager
  http://www.Vistax64.com/tutorials/193584-Device-Manager-install-driver.html

  If you update the drivers manually, then it's a good idea to disable the facilities of driver in the Windows updates,
  This leaves ONE of Windows updates, but it will not install the drivers who are generally older and cause
  questions. If updates offers a new driver and then hide it (right click on it) and then go look for new ones
  manually if you wish.

  How to disable automatic driver Installation in Windows Vista - drivers
  http://www.AddictiveTips.com/Windows-Tips/how-to-disable-automatic-driver-installation-in-Windows-Vista/
  http://TechNet.Microsoft.com/en-us/library/cc730606 (WS.10) .aspx

  ----------------------------------------------------------

  My generic blue screen troubleshooting if necessary:

  Here are a few ways to possibly fix the blue screen issue. If you could give the info from the blue screen that would be
  Help. Such as ITC and 4 others entered at the bottom left. And any other information such as STOP error
  codes and info like IRQL_NOT_LESS_OR_EQUAL or PAGE_FAULT_IN_NONPAGED_AREA and similar messages.

  As examples:

  BCCode: 116
  BCP1: 87BC9510
  BCP2: 8C013D80
  BCP3: 00000000
  BCP4: 00000002

  or in this format:

  Stop: 0 x 00000000 (oxoooooooo oxoooooooo oxoooooooo oxooooooooo)
  Tcpip.sys - address blocking 0 x 0 00000000 000000000 DateStamp 0 x 000000000

  It is an excellent tool for displaying the blue screen error information

  BlueScreenView scans all your minidump files created during 'blue screen of death' crashes, and displays the
  information on all accidents of a table - free
  http://www.NirSoft.NET/utils/blue_screen_view.html

  BlueScreens many are caused by old or damaged drivers, video drivers in particular, but there are other causes.

  You can follow these steps in the Safe Mode if necessary or the command prompt Vista DVD or Options of recovery if your
  system installed by the manufacturer.

  This tells you how to access the System Recovery Options and/or a Vista DVD
  http://windowshelp.Microsoft.com/Windows/en-us/help/326b756b-1601-435e-99D0-1585439470351033.mspx

  You can try a system restore to a point before the problem started when one exists.

  How to make a Vista system restore
  http://www.Vistax64.com/tutorials/76905-System-Restore-how.html

  -----------------------------------------------------

  Start - type this in the search box-> find COMMAND at the top and RIGHT CLICK – RUN AS ADMIN

  Enter this at the command prompt - sfc/scannow

  How to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe) program
  generates in Windows Vista cbs.log
  http://support.Microsoft.com/kb/928228

  The log can give you the answer if there is a corrupted driver. (Says not all possible driver problems).

  Also run CheckDisk, so we cannot exclude as much as possible of the corruption.
  How to run the check disk at startup in Vista
  http://www.Vistax64.com/tutorials/67612-check-disk-Chkdsk.html

  ------------------------------------------------------------------

  Often drivers up-to-date will help, usually video, sound, network card (NIC), WiFi, 3rd party keyboard and
  smile, as well as of other major device drivers.

  Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
  http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htm

  How to install a device driver in Vista Device Manager
  http://www.Vistax64.com/tutorials/193584-Device-Manager-install-driver.html

  How to disable automatic driver Installation in Windows Vista - drivers
  http://www.AddictiveTips.com/Windows-Tips/how-to-disable-automatic-driver-installation-in-Windows-Vista/
  http://TechNet.Microsoft.com/en-us/library/cc730606 (WS.10) .aspx

  ------------------------------------------------------------------
  How to fix BlueScreen (STOP) errors that cause Windows Vista to shut down or restart unexpectedly
  http://support.Microsoft.com/kb/958233

  Troubleshooting, STOP error blue screen Vista
  http://www.chicagotech.NET/Vista/vistabluescreen.htm

  Understanding and decoding BSOD (blue screen of death) Messages
  http://www.Taranfx.com/blog/?p=692

  Windows - troubleshooting blue screen errors
  http://KB.wisc.edu/page.php?id=7033

  ------------------------------------------------------------------

  In some cases, it may be necessary.

  The Options or Vista recovery disk Startup Repair

  How to do a startup repair
  http://www.Vistax64.com/tutorials/91467-startup-repair.html

  This tells you how to access the System Recovery Options and/or a Vista DVD
  http://windowshelp.Microsoft.com/Windows/en-us/help/326b756b-1601-435e-99D0-1585439470351033.mspx

  I hope this helps.

  Rob - bicycle - Mark Twain said it is good.

• Startup VAIO problem - unknown blue screen at startup

  I have a Sony PCG - 71913L microcomputer model. It does not start. I tried both startup option, but even in this case, it is showing a blue screen after restart! can someone give me a solution please. I don't have the CD with me right away. Thank you.

  Hi shabnamshaila,

  ·         Did you do changes on the computer before the show?

  ·         What is the exact error message?

  Follow these methods.

  Method 1: Unplug all external devices (except the mouse and keyboard) and check if you are able to boot to the desktop.

  Method 2: If this isn't the case, you need a Windows XP CD to troubleshoot more far. When you have the Windows XP CD follow the steps form the article.

  How do I recover from a corrupted registry that prevents Windows XP startup

  http://support.Microsoft.com/kb/307545

• Unable to start - blue screen after Windows update

  original title; on dell dimension C521... blue screen after Windows update last night 3/9...3:00am...running Vista

  Can not even go in safe mode

  Hello

  try to do a startup repair or a system restore before the update using the Startup Repair disk if you don't have a vista dvd microsoft

  the link below is how to download and get a vista disk startup repair, which you can start from the

  http://NeoSmart.net/blog/2008/Windows-Vista-recovery-disc-download/

  Here's how to use startup repair system restore command prompt, etc. to bleepingcomputers link below

  http://www.bleepingcomputer.com/tutorials/tutorial148.html

  to boot from the dvd drive to be able to you will see a way to get into the bios Setup at the bottom of the screen or command menu start

  It would be F2 or delete etc to enter the BIOS or F12 etc. for the start menu

  Change boot order it do dvd drive 1st in the boot order

  If you can make the above change how you receive updates to find the update problem

  When right-clicking on it UAC prompt you hide it

  http://www.bleepingcomputer.com/tutorials/tutorial140.html

  Choose one of these settings:

  Download updates but let me choose whether to install them - if you select this option, Windows will download the updates on your computer, but not install them automatically. If you want to install updates, then you must install them manually. You should only select this option if you have a reason to not install updates automatically. Only advanced users should use this option.

  Check for updates but let me choose whether to download and install them - if you select this option, you'll be alerted when there are new updates available for download and install. You can then choose to download and install the updates that you want. This option should really be reserved for people who know exactly which updates they need, or those who have little access to the Internet.

• Blue screen on startup, the system restore / repair did not work?

  Hi, I get a blue screen on startup and cannot start windows - with the error code x0000007E.

  I followed the steps on http://support.microsoft.com/kb/958233#StartupRepair however runs the repair does not work, and did the system restore.

  Will be saved my files / is there a way to fix this? Thank you!

  Hello

  You can save your files by putting the drive in another computer as a 2nd disk (best) or external
  Drive USB enclosure and then backup to removable media such as CD, DVD or other USB drives.
  Of course a real store of the computer or the manufacturer of your system can help to recover the files.

  Or you can use a boot Ubuntu CD to back up data.

  Use Ubuntu Live CD to backup files from your Windows computer dead
  http://www.howtogeek.com/HOWTO/Windows-Vista/use-Ubuntu-Live-CD-to-backup-files-from-your-dead-Windows-computer

  --------------------------------------------------------------

  Check this thread for more information using BlueScreenView, MyEventViewer and other methods
  to troubleshoot the BlueScreens - top 3 responses (+ 1 other).

  http://social.answers.Microsoft.com/forums/en-us/vistarepair/thread/3deab2fa-4000-4136-8c78-a3d22b1db009

  We can analyze the minidumps if make you it available to the SkyDrive or another file
  sharing sites.

  ZIP or download the content of the C:\Windows\minidump

  Use SkyDrive download collected files and after shot/screenshot.
  http://social.technet.Microsoft.com/forums/en-us/w7itproui/thread/4fc10639-02dB-4665-993a-08d865088d65

  -------------------------------------------------------------------------

  Also this, so you can see the probable bluescreens.

  Windows Vista restarts automatically if your computer encounters an error that requires him to plant.
  (also Windows 7)
  http://www.winvistatips.com/disable-automatic-restart-T84.html

  ===========================================================

  The system has RAID? If so, it's also very suspicious.

  This error is usually a driver problem and display adapter (video) driver is the most suspicious if she
  may be others. Antivirus/antispyware/security programs, equipment (heat) and major software problems
  can also cause the error. When you get to the section of the driver to use the Troubleshoot utility my generic
  methods in the next message and then return to the if necessary troubleshooting tool.

  Have you recently added hardware or drivers updated? Don't forget to look in Control Panel - Windows
  Updates to see if all drivers have been updated it. Other donor opportunities include the antivirus/anti-
  spyware/security programs.

  When you get to the pilot and sections of the memory of the troubleshooter check the following message to
  update drivers and memory test and then return to the troubleshooter if necessary.

  BCCode: 7F 0x0000007E which is also 0x1000007E

  Cause

  SYSTEM_THREAD_EXCEPTION_NOT_HANDLED bug control is a very common bug control. TO
  interpret, you must identify which exception has been generated.

  Common exception codes are:

  • 0xc0000005: STATUS_ACCESS_VIOLATION indicates a memory access violation has occurred.

  For a complete list of exception codes, see the Ntstatus.h file located in theinc directory
  the Microsoft Windows Driver Kit (WDK).

  Solve the problem

  If you do not have to debug this problem, you must use certain basic troubleshooting techniques.

  • Make sure you have enough disk space.
  • If a driver is identified in the bug check message, disable the driver or check with the
  • Reference of the manufacturer for driver updates.
  • Try changing video cards.
  • Check with your hardware vendor for updates to the BIOS.
  • Disable the BIOS memory options such as implementing caching or shading.

  If you plan to debug this problem, you may find it difficult to get a stack trace. Parameter 2
  (the address of the exception) must identify the driver or function that caused the problem.

  If the exception code 0 x 80000003 occurs, a hard-coded breakpoint or assertion was hit, but the system
  has been launched with the /nodebug. switch. This problem should occur infrequently. If it occurs repeatedly,
  Make sure that a kernel debugger is connected and the system is booted with the Switch/DEBUG .

  In case of exception code 0 x 80000002, the trap frame provides additional information.

  If you do not know the specific cause of the exception, consider the following questions:

  • Hardware incompatibility. Make sure all new hardware that is installed is listed in the
  • List of Microsoft Windows Marketplace tested products.
  • Service driver or defective peripheral system. A service driver or defective peripheral system can be
  • responsible for this error. Hardware problems, such as the incompatibilities of the BIOS, memory, conflicts
  • and IRQ conflicts can also generate this error.

  If a driver is listed by name in the bug check message, disable or remove that driver. Disable
  or remove drivers or services that have been recently added. If the error occurs during startup
  sequence and the system partition is formatted with the NTFS file system, you may be able to use safe
  Mode to rename or to delete the faulty driver. If the driver is used as part of the system startup procedure
  in Safe Mode, you must start the computer by using the Recovery Console to access the file.

  If the problem is associated with Win32k.sys, the source of the error may be a third remote
  control program. If this software is installed, you can remove the boot of the computer service
  by using the Recovery Console, and then by removing the offending system service file.

  Check the system log in Event Viewer for additional error messages that might help identify the
  device or the driver that generated the bug check 0x7E.

  You can also disable memory cache BIOS may try to resolve the error. You should also
  Run the diagnostics of material, especially the scanner memory, which provides the manufacturer of the system.
  For more information about these procedures, see the manual of your computer.

  The error that generates this message may occur after the first reboot during Windows Setup, or
  Once the installation is complete. A possible cause of the error is lack of disk space for installation and system
  BIOS incompatibilities. For problems during the installation of Windows that are associated with the absence of disc
  space, reduce the number of files on the disk drive hard target. Find and delete any temporary
  the files that you do not have to have files hidden Internet, backup application and.chkfiles files that
  contain fragments of file saved to disk scans. You can also use another hard drive with more drive
  free space for the installation. You can solve the problems of BIOS by upgrading the version of the system BIOS.

  BCCode: 7F 0x00000007E who is also a 0x1000007E<-- read="" this="">
  * 1141.html? order = votes http://www.faultwire.com/solutions-fatal_error/System-thread-exception-not-HANDLED-0x0000007E-

  ----------------------------------------------------------------------------------------------------------------------

  Look in the Event Viewer to see if something is reported on those.
  http://www.computerperformance.co.UK/Vista/vista_event_viewer.htm

  MyEventViewer - free - a simple alternative in the standard event viewer
  Windows. TIP - Options - Advanced filter allows you to see a time rather
  of the entire file.
  http://www.NirSoft.NET/utils/my_event_viewer.html

  Here are a few ways to possibly fix the blue screen issue. If you could give the blue screen
  info that would help. Such as ITC and 4 others entered at the bottom left. And all others
  error information such as codes of STOP and info like IRQL_NOT_LESS_OR_EQUAL or PAGE_FAULT_IN_NONPAGED_AREA and similar messages.

  As examples:

  BCCode: 116
  BCP1: 87BC9510
  BCP2: 8C013D80
  BCP3: 00000000
  BCP4: 00000002

  or in this format:

  Stop: 0 x 00000000 (oxoooooooo oxoooooooo oxoooooooo oxooooooooo)
  Tcpip.sys - address blocking 0 x 0 00000000 000000000 DateStamp 0 x 000000000

  It is an excellent tool for displaying the blue screen error information

  BlueScreenView scans all your minidump files created during ' blue screen of the.
  death ' crashes and displays information about all accidents of a table.
  Free
  http://www.NirSoft.NET/utils/blue_screen_view.html

  BlueScreens many are caused by drivers of old or damaged, in particular the video drivers
  However, there are other causes.

  You can do mode if necessary safe or the Vista DVD command prompt or
  Options recovery if your system is installed by the manufacturer.

  This tells you how to access the System Recovery Options and/or a Vista DVD
  http://windowshelp.Microsoft.com/Windows/en-us/help/326b756b-1601-435e-99D0-1585439470351033.mspx

  You can try a system restore to a point before the problem started when one exists.

  How to make a Vista system restore
  http://www.Vistax64.com/tutorials/76905-System-Restore-how.html

  -------------------------------------------------------------------------

  Start - type this into the search-> find COMMAND to top box and RIGHT CLICK-
  RUN AS ADMIN

  Enter this at the command prompt - sfc/scannow

  How to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe)
  program generates in Windows Vista cbs.log
  http://support.Microsoft.com/kb/928228

  The log can give you the answer if there is a corrupted driver. (Does not work
  tell all possible driver issues).

  Also run CheckDisk, so we cannot exclude as much as possible of the corruption.

  How to run the check disk at startup in Vista
  http://www.Vistax64.com/tutorials/67612-check-disk-Chkdsk.html

  -------------------------------------------------------------------------

  Often drivers up-to-date will help, usually video, sound, network card (NIC), WiFi, part 3
  keyboard and mouse, as well as of other major device drivers.

  Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
  http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htm

  How to install a device driver in Vista Device Manager
  http://www.Vistax64.com/tutorials/193584-Device-Manager-install-driver.html

  How to disable automatic driver Installation in Windows Vista - drivers
  http://www.AddictiveTips.com/Windows-Tips/how-to-disable-automatic-driver-installation-in-Windows-Vista/
  http://TechNet.Microsoft.com/en-us/library/cc730606 (WS.10) .aspx

  -------------------------------------------------------------------------

  How to fix BlueScreen (STOP) errors that cause Windows Vista to shut down or restart
  quit unexpectedly
  http://support.Microsoft.com/kb/958233

  Troubleshooting, STOP error blue screen Vista
  http://www.chicagotech.NET/Vista/vistabluescreen.htm

  Understanding and decoding BSOD (blue screen of death) Messages
  http://www.Taranfx.com/blog/?p=692

  Windows - troubleshooting blue screen errors
  http://KB.wisc.edu/page.php?id=7033

  -------------------------------------------------------------------------

  In some cases, it may be necessary.

  The Options or Vista recovery disk Startup Repair

  How to do a startup repair
  http://www.Vistax64.com/tutorials/91467-startup-repair.html

  This tells you how to access the System Recovery Options and/or a Vista DVD
  http://windowshelp.Microsoft.com/Windows/en-us/help/326b756b-1601-435e-99D0-1585439470351033.mspx

  I hope this helps.

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle="" -="" mark="" twain="" said="" it="">

• Help with restarting the laptop HP pavilion g6 auto blue screen after installing VMWare Workstation 7/8

  Hello, I have a HP Pavilion g6-1a52nr Notebook PC (running Windows 7 64 bit) which is in a reboot loop. This happened after I installed VMWare Workstation 7 (in the installation process there is no occurs.but error after installing that I try to reboot the machine, and then the following error has occurred).
  Now whenever the notebook starts up, it seems to be in a reboot loop after the windows logo then get a blue screen.
  When I connect to the system using vmware safemode also working.but in normal mode it displays a blue screen after logiin screen shows.

  By turning on the restart automatic system failure off I was able to read it as the Blue error message that says:
  -

  Signature of the problem:
  Problem event name: BlueScreen
  OS version: 6.1.7601.2.1.0.256.1
  Locale ID: 1033

  More information about the problem:
  BCCode: 1000007e
  BCP1: FFFFFFFFC0000005
  BCP2: FFFFF88006EFF443
  BCP3: FFFFF88003399D68
  BCP4: FFFFF880033995C0
  OS version: 6_1_7601
  Service Pack: 1_0
  Product: 256_1

  Files helping to describe the problem:
  C:\Windows\Minidump\031212-28672-01.dmp
  C:\Users\user\AppData\Local\Temp\WER-62072-0.SysData.XML

  Read our privacy statement online:
  http://go.Microsoft.com/fwlink/?LinkId=104288 & clcid = 0 x 0409

  If the online privacy statement is not available, please read our offline privacy statement:
  C:\Windows\system32\en-US\erofflps.txt

  
  -
  Can someone give me advice on how to solve and prevent this problem?

  
  Thank you

  you have the HP-tools installed?
  They often conflict with VMware.
  Try disabling the startup of the HP-tools

• Equium A60 blue screen after updating XP Home SP2

  I have a Toshiba Equium A60-692. I have updated to XP SP2 and now get up a blue screen at startup with the message that ATI driver ati2dvg is entered in a continuous loop. The Microsoft error report says it is because of incompatible drivers, but I have the latest driver from Toshiba.

  Anyone have any ideas?

  Hi Laura,

  Did you install CD driver "Tools & Utilities" that you got with your laptop?

• Satellite L450D - 13 X - blue screen after BIOS update

  I have the blue screen after BIOS update. Satellite L450D - 13 X worked ok before that ideas?

  Is there contact information for Support TOSHIBA?

  Hey,.

  > Is there any TOSHIBA support contact information?
  No, becaue, must contact an authorized service provider. Guys can help on any hardware and software problems and can also order spare parts from Toshiba.

  Here is a list of aspic, where you can look closer:
  http://EU.computers.Toshiba-Europe.com/innovation/generic/ASP_SUPPORT

  Good luck! :)
  ?

• 8530p blue screen after the awakening of the mode standby.

  Hello.

  Windows 7 Enterprise 32-bit. (EDITED)

  A user has a problem as his computer blue screens after he was awakened to "sleep" mode and the other thing is this problem is intermittent.

  The error message I saw said that it was a KERNEL_DATA_INPAGE_ERROR STOP error message is 0x0000007A and the second parameter was 0xC000009D.

  According to http://msdn.microsoft.com/en-us/library/ff559211 (v = vs. 85) .aspx this type of error indicates - "0xC000009D or STATUS_DEVICE_NOT_CONNECTED, indicates defective wiring or in bulk, termination or that the controller does not see the hard drive."

  Hard disk, I ran the tests integrated in the BIOS, online tool check the system of HP for laptop PC (http://h20239.www2.hp.com/techcenter/HP_SystemCheck/hp_syscheck.htm) and same Seagates own Seatool because there is a Seagate drive in the machine. All these tests said nothing about a problem with the hard drive.

  The online tool, said there is no update available on the BIOS drivers.

  I even had the user to remove the hard drive and put it back to make sure he wasn't a wire loose, bad connection or something like that.

  I phoned helpdesk of HP where I live and I told him this and he said that it is most likely a software problem.

  So so I need help to find out what software might be behind this error.

  I can't provide shocks either, given the error and blue screen also says "dump of physical memory failed with status 0xC0000010.".

  So is it a known software that could be the cause of these problems?

  EDIT: As pointed out by erico, I forgot the information about this operating system. That's why I added this information at the top of my first post.

  Sorry I have not responded earlier.

  It seems that the problem is solved since the user had no blue screens for over a week now.

  The solution was quite simple: reinstall on a new hard drive, even if each test drive, I ran on the subject, said the old drive was ok. This includes BIOS integrated HP and test online, chkdsk in Windows 7 and Seagate tool own Seatool.

  Best regards

  Ljungan.

• Get windows error blue screen after installation Service

  I'm getting error " PAGE_FAULT_IN_NONPAGED_AREA_ (nischifk.sys)" blue screen after installing the VISION acquisition software in my OS Windows 10.

  I tried to install GO twice and got the same error.

  Awating for your valuable review

  Hi piZviZ,

  Sorry to hear about installation problems going TO that appeal to you. I guess you use going TO February 2014 or slightly earlier - can you confirm? There was a problem with one of the components, NEITHER FlexRIO going to understand which caused this exact problem on systems with a UEFI BIOS. We have since fixed the problem. If that were the problem, here are a few options:

  (1) install GO without Support IMAQ i/o for all cards of the R series (1473R, 8237R, etc.). This means that the affected FlexRIO component will not be installed.

  (2) update to a newer version of GO - I think that going TO August 2014 f1 shoots in the FlexRIO patched component that could solve the problem. If you choose to upgrade, I would recommend just upgrading to the last GO, if you are capable of: going TO August 2015 f1

  (3) keep the version of going TO you and patch the component FlexRIO: How can I get a blue screen after installation OR FlexRIO 13.1?, NI FlexRIO 13.2.0 Patch détails

  I recommend just update to the latest going TO if possible.

  Kind regards

  Joseph

• Blue screen after the recent updates of security for Windows XP SP3.

  I got following error messages "Blue screen" after the latest updates from Microsoft:

  0X0000007E (0X8053355E, 0XBA4CB50C, 0 X 80000003, $0XBA CB208). I tired to run in all modes of SECURITY but still had the same problem. I ran Dell diagnostics and it came with no error in memory or hard drive. I have a Dell Inspiron B130 w/2 MB of RAM. Does anyone have a solution? The laptop came with no CD boot.

  @Jazzman1962 and flowie,

  I suggest you follow the steps mentioned by 'LThibx' in the http://social.answers.microsoft.com/Forums/en-US/vistawu/thread/73cea559-ebbd-4274-96bc-e292b69f2fd1thread.

  -------------------------------------------------------------------
  Naveen
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

• Blue screen after installation KB2393802 / KB890830

  Windows 7 Ultimate

  I received today a handful of updates. He finished in a blue screen after reboot. Only with the restoration of the point system that I was able to start in the normal way of restoration. I installed every update one by one and was able to isolate the problem. Each of these two updates (KB2393802/KB890830) which brings back me to the blue screen. I also tried to download and install these updates manually, but had no success.

  My impression is also that other side to this problem if you for example search KB2393802 on google.

  Is it a known Microsoft issue and if there is a fix available for this?

  Any hint is appreciated.

  Cheers, mikeych

  Hello. Has been able to solve the problem. Update some hardware (e.g. video) drivers and the system once again stable. No more appeart to blue screen after installing the MS updates again.

• Blue screen after installing security update KB2419640

  After I installed Windows 7 security update KB2419640, I get a blue screen after reboot and finally do a system restore.  Can someone explain how to get this update to work? I have tried several times now and it installs by is kind of lonely. Don't know what else to do.

  TIA

  See this post in the Windows Update forum: http://social.answers.microsoft.com/Forums/en-US/vistawu/thread/10eb9b57-aada-4c49-acf1-b81f016b1ed0

  JS
  http://www.PAGESTART.com

  Never be afraid to ask. This forum has some of the best people in the world to help.