Similar Questions

• SETUP-EPRINT PRINTER COMMUNICATION FAILURE

  LaserJet CP1025nw - I used to print my eprint software, but after updating firmware, everything went wrong. print the status page, no IP address and no network. Printer was uninstalled, reinstalled again. connected to the router; got the new IP address. checked to be in the same network with the router and the laptop; HP Connect recorded for eprint; eneterd assigns the code and adds the device to my account eprint. tried to print when the usb cable is attached works very well.

  The problem is when I try to install the eprint application it shows my printer with the correct IP address but then in the next step it keep saying "communication failure". I disabled windows firewall and no proxy is installed; always impossible to communicate. I have two laptops; working with windows 7 and the other with windows 8. Both has the same problem. I tried all the solutions I found on the HP site but without success. It made me desperate. It is the last solution for me before leaving this printer to buy a new one.

  Hi BAKJAF,

  Welcome to the Forums of HP's Support.  I understand you get a connection error message when you try to activate the web services of your printer, regardless of which computer you are using to enable web services.

  Please define Manual of the printer an IP address manually and DNS servers.  The steps are in the

  Document of the printer is not maintaining the wireless connection .  Look in the Windows section for "three Solution: the printer of the assign a static IP address.  The manual preferred DNS server please use 8.8.8.8 and 8.8.4.4 use for replacing manual DNS server.

  Once you have configured the IP address manually and manual DNS servers please try to enable web services.

  Please let me know how it goes.

• Cannot install the program, the error message: Server error 145905 [invalid header] communications failure

  Original title: communication failure 145905 [invalid header]

  When you try to install a program I always get this error each time message: Server error 145905 communication failure [invalid header] would appreciate any help that anyone can provide. Thank you.

  Hello

  That is the application that you are trying to install?

  I suggest you follow these methods and check.

  Method 1: Run the hotfix to correct the following problems with programs that cannot be installed or uninstalled

  http://support.Microsoft.com/mats/Program_Install_and_Uninstall/

  Method 2: Perform the clean boot, try to install application.

  Follow the suggestions of this link.

  http://support.Microsoft.com/kb/310353

  NOTE: Once you check the functionality, follow the suggestions under steps to configure Windows to use a Normal startup state.

  If the problem is specific to the program, I suggest you please contact the manufacturer of the program for utilities.
   

  I hope this helps!

• "A communication failure has occurred" when you transfer the file in Simulator

  I'm under Blackberry MDS Services 4.1.2 and using device Blackberry 9530 Simulator Simulator.  v4.7.0.75

  -Only the Blackberry browser is an option on this Simulator.

  -The Web page is a form that has an input file browse that selects an image file on the Simulator.  The form sends, but after 20-30 seconds, it seems to start timing and finally returns the error message below.

  -The same Web page works on a real device of Blackberry 9530 Storm without error.

  Error:

  A communication failure occurred with the chosen Mobile Data Service. The server may be busy, please try again later.  If the problem persists, contact your administrator.

  http://www.w3.org/1999/xhtml">
  
  
    
    
  
  
  
  
    
    
  
  
  
  
  Upload
  
  
  * Required field.
  
  
  
  smith, john
  
  
  1111 JAMES DR, New York, NY, 44444
  
  
  9234HH111111 (Property)
  
  
  Effective 02/14/2009
  
  
  
    
  
  
  
  
  File *
  
  
    
  
  
  
  
  Type *
  
  
  
    
  PHOTOGRAPH
    
    
  CLUE REPORT
    
    
  OYSC BUNDLE
    
    
  NY VEH INSPEC
    
    
  AGT FILES
    
  
  
  
  
  
  Desc
  
  
  
  
  
  
  
   
  
  
    
  
  
  
  
  
  
  
  
  ©2009 Insurance Company. All rights reserved.
  
  
  
  

  Support or ideas are appreciated.  Thanks in advance.

  Blueinc good tip.  I noticed that you were using the MDS of the JDE 4.7.0:

  C:\Program search in Motion\BlackBerry JDE 4.7.0\MDS

  I had been using the MDS for the stand-alone package of RIM:

  C:\Program 4.1.2\MDS search Motion\BlackBerry Email and MDS Services Simulator

  As soon as I tried the JDE 4.7.0 MDS, it worked without making any changes of rimpublic.property!

  So it seems that the bug is with 'BlackBerry email and MDS Services 4.1.2 simulators' MDS.  Thanks for pointing me the finger inadvertently in the right direction!

  Would be nice if RIM could fix the own MDS.

• Active due to Communication failure to the Audio System of the TV speakers

  Hi, I own a Sony LED W804a and also home theater BDV E880. I connected two receivers, my Apple TV and home theater HDMI ports to TV... Everything worked fine, but all of a sudden my TV screen started showing the following message 'Active due to the failure of Communication of the TV speakers Audio System'. After this message, audio is played through the TV speakers. Please note that during startup, television displays the message as 'Active Audio System', but later displays the previous message stated, and the audio comes through the TV speakers. Please help how to solve this problem. I made sure that the settings are made so that the audio output, I chose Audio System NOT the TV speakers. Also when I try to Bravia Sync between these two devices, the TV seems that certain signals to detect devices connected, but then it says no devices listed. TV and home theater, I kept on the Bravia sync options.
  Help, please...

  Could be as simple as a bad cable... what type of audio system?

• Communication failure USRP 2952R after loading image

  Background

  I recently started working with the NOR-2952R (X 310) and I'm trying to contact her on the 1 GB NETWORK card on a Linux server.  I am very familiar with the USRP N-210 and I'm looking to use it in a similar way.

  Problem

  My host uses UHD 003.007.001 so when I first performed a uhd_usrp_probe, I got the standard incompatibility message shown below, so I reimagee with the X 310 bit file comes from uhd_images_downloader.  The little-used file was usrp_x310_fpga_HGS.bit.

  Error: RuntimeError: number of firmware compatibility 0x3 WAITED, but had 0x4.0

  After loading the new image, I received x 300 errors of communication/fw as follows:

  [user@host ~] $ / usr/bin/uhd_usrp_probe - addr = 192.168.10.2 args
  
  Linux; GNU C++ version 4.4.7 20120313 (Red Hat 4.4.7 - 4); Boost_104100; UHD_003.007.001 - 0-unknown
  
  UHD error:
  
      x 300 failure communication fw #1
  
      EnvironmentError: IOError: x 300 poke32 fw - answer has expired
  UHD error:
  
      x 300 failure communication fw #1
  
      EnvironmentError: IOError: x 300 peek32 fw - answer has expired

  After a repair this problem for a few hours, I think I have bricked my device and I train using the JTAG interface to reimage the appliance.

  Question

  What is the right image to load for the UHD 003.007.001 driver and how to fix the failures of communication?  My server using a Broadcom NIC and I saw another post, suggesting that users had issues with Realtek NIC.

  Thank you.

  As a follow-up, my camera was indeed bricks by a corrupt charge.  I initially loaded (and subsequently recovered) my camera with the command below.

  [user@host ~] $ sudo/usr/bin/usrp_x3xx_fpga_burner - addr 192.168.10.2 - fpga-path /usr/share/uhd/images/usrp_x310_fpga_HGS.bit

  I was able to retrieve my device via JTAG with the same bit file and persisted in my image with the same command above.

  Go Hoos.

• LDAP failures between Windows 2008R2 AD domain controllers.

  Is there a failure rate tolerable for LDAP queries between domain controllers? We are seeing rates of non-response (retransmit packets) between domain controllers because the port 3268 for Global catalog LDAP fails about 3% of the time. What is a rate normal or tolerated in AD?

  Hi Gonzolean,

  Thanks for posting on Microsoft Community.

  This question might be the best answer by TECHNET forums. They have experts who can
  solve this problem. Then I suggest you to post on the TECHNET forums.

  https://social.technet.microsoft.com/Forums/en-US/home?forum=windowsserver2008r2management%2Cwindowsserver2008r2highavailability%2Cwindowsserver2008r2virtualization&filter=alltypes&sort=relevancedesc&brandIgnore=True&filter=alltypes&searchTerm=ldap

  In the future if you have problems with Windows. Not to contact us. We will be happy to help you.

• Communication problem between the FPGA VI and VI host-PC

  Dear Sir

  I am trying to establish a communication between a FPGA a PC host using the FPGA FIFO.

  The communication still has a few problems and I do not know what cause them.

  LabVIEW gives me the following reason "transfer has not completed within a stated time period, or in the specified number of retries."

  What is the problem with my labview program? How can I solve this?

  The project are attached.

  Best regards

  Beurms Jasper

  Hello, Jasper.

  Based on your feedback that a good approach might be to use DMA FIFO of the FPGA on the RT controller and use the network stream to send all on the network.

  Please note that (based on your original code), may also be useful to take a look at the use of DMA FIFO with interlacing.

  PS: I mention this because there is a limit on how many DMA FIFOs, you can use onach RIOtarget.

• Communication problem between the listener and OEM

  Hi all
  I got my OEM running and communicates with the database without any problem until I had a problem with the other guests and to kill some OEM process and listener, now it does not communicate with the listener.
  
  I rebooted my PC and tried to leave in the hope that it worked as it had been, but the result is on the contrary. Somehow, the communication is corrupt. Currently, I can start the OEM help

  emtcl start dbconsole

  but when I try to start the listener from the browser of Net Services Administration: connection to the host, it keeps from without success.
  
  What follows is the trace file of the Manager, who got warnings and errors that I don't understand

  emagent.trc:
  
  SQL = "                                                                   OCISessionGet"...
  LOGIN = dbsnmp/<PW>@(DESCRIPTION=(ADDRESS=(PROTOCOL=TCP)(HOST=firefly.snowdrop.com)(PORT=1521))(CONNECT_DATA=(SID=inara)))
  2011-06-14 17:22:42,398 Thread-421710160 ERROR vpxoci: ORA-12541: TNS:no listener
  2011-06-14 17:22:42,398 Thread-421710160 WARN  vpxoci: Login 0x68d100 failed, error=ORA-12541: TNS:no listener
  2011-06-14 17:22:42,398 Thread-421710160 WARN  TargetManager: Exception in computing dynamic properties of {inara.snowdrop.com, oracle_database },GetDbBlockSize::ORA-12541: TNS:no listener
  2011-06-14 17:22:42,400 Thread-424859984 ERROR TargetManager: nmeetm.c : Target inara.snowdrop.com has a failed critical dynamic property
  2011-06-14 17:22:42,403 Thread-424859984 WARN  upload: Upload manager has no Failure script: disabled
  2011-06-14 17:22:42,403 Thread-424859984 WARN  upload: Amount of upload data will be recalculated due to reload.enabling collections and regenerating metadata.
  2011-06-14 17:22:42,403 Thread-424859984 WARN  TargetManager: Regenerating all Metadata
  2011-06-14 17:22:42,470 Thread-424859984 WARN  upload: Truncating value of "SHORT_NAME" from "Average Synchronous Single-Block Read Latency (ms)" to "Average Synchronous Single-Block Read La"
  2011-06-14 17:22:42,471 Thread-424859984 WARN  upload: Truncating value of "SHORT_NAME" from "Average Synchronous Single-Block Read Latency (ms)" to "Average Synchronous Single-Block Read La"
  2011-06-14 17:22:42,568 Thread-424859984 WARN  upload: Truncating value of "COLUMN_LABEL" from "Total messages processed per queue per subscriber per minute in the last interval" to "Total messages processed per queue per subscriber per minute in "
  2011-06-14 17:22:42,568 Thread-424859984 WARN  upload: Truncating value of "COLUMN_LABEL" from "Total messages received per queue per subscriber per minute in the last interval" to "Total messages received per queue per subscriber per minute in t"
  2011-06-14 17:22:42,568 Thread-424859984 WARN  upload: Truncating value of "COLUMN_LABEL" from "Messages processed per queue (%) per subscriber per minute in the last interval" to "Messages processed per queue (%) per subscriber per minute in th"
  2011-06-14 17:22:42,568 Thread-424859984 WARN  upload: Truncating value of "COLUMN_LABEL" from "Age of the first message in persistent queue per subscriber (seconds)" to "Age of the first message in persistent queue per subscriber (sec"
  2011-06-14 17:22:42,568 Thread-424859984 WARN  upload: Truncating value of "COLUMN_LABEL" from "Age of the first message in the buffered queue per queue (seconds)" to "Age of the first message in the buffered queue per queue (second"
  2011-06-14 17:22:42,584 Thread-424859984 WARN  collector: enable collector
  2011-06-14 17:22:42,588 Thread-424859984 WARN  collector: Regenerating all DefaultColls
  2011-06-14 17:22:43,715 Thread-421710160 ERROR upload: Exceeded max. amount of upload data: 212 files, 200.680481 MB Data. 88.62% of disk used. Disabling collections.
  2011-06-14 17:22:43,715 Thread-421710160 WARN  collector: Disable collector
  2011-06-14 17:22:46,814 Thread-421710160 ERROR pingManager: nmepm_pingReposURL: Did not receive a response header from repository
  2011-06-14 17:22:46,929 Thread-421710160 ERROR pingManager: nmepm_pingReposURL: Did not receive a response header from repository
  2011-06-14 17:23:16,099 Thread-435099984 ERROR command: nmejcn: received no status header from repository at https://firefly.snowdrop.com:5500/em/upload/
  2011-06-14 17:23:17,071 Thread-415410512 ERROR pingManager: nmepm_pingReposURL: Did not receive a response header from repository
  2011-06-14 17:23:17,201 Thread-415410512 ERROR pingManager: nmepm_pingReposURL: Did not receive a response header from repository
  2011-06-14 17:24:17,230 Thread-424859984 WARN  ssl: <nmehlssl.c:nmehlssl_readcb>: nmehl_read_sock timed out, rsf = -5, setting read timeout flag
  2011-06-14 17:24:17,230 Thread-424859984 WARN  ssl.io: fd=14: nmehlssl_read, nzos_Read error = 28862 readTimed Out = 1
  2011-06-14 17:24:17,230 Thread-424859984 WARN  http: <nmehl.c>:<nmehl_readline>: nmehlssl_read() timed out
  2011-06-14 17:24:17,230 Thread-424859984 ERROR pingManager: nmepm_pingReposURL: Error in request response. code = 400. text = 
  2011-06-14 17:24:47,355 Thread-424859984 WARN  ssl: <nmehlssl.c:nmehlssl_readcb>: nmehl_read_sock timed out, rsf = -5, setting read timeout flag
  2011-06-14 17:24:47,355 Thread-424859984 WARN  ssl.io: fd=7: nmehlssl_read, nzos_Read error = 28862 readTimed Out = 1
  2011-06-14 17:24:47,355 Thread-424859984 WARN  http: <nmehl.c>:<nmehl_readline>: nmehlssl_read() timed out
  2011-06-14 17:24:47,355 Thread-424859984 ERROR pingManager: nmepm_pingReposURL: Error in request response. code = 400. text = 
  2011-06-14 17:25:47,446 Thread-315353424 WARN  ssl: <nmehlssl.c:nmehlssl_readcb>: nmehl_read_sock timed out, rsf = -5, setting read timeout flag
  2011-06-14 17:25:47,446 Thread-315353424 WARN  ssl.io: fd=7: nmehlssl_read, nzos_Read error = 28862 readTimed Out = 1
  2011-06-14 17:25:47,446 Thread-315353424 WARN  http: <nmehl.c>:<nmehl_readline>: nmehlssl_read() timed out
  2011-06-14 17:25:47,446 Thread-315353424 ERROR pingManager: nmepm_pingReposURL: Error in request response. code = 400. text = 

  and here is the content of the file log listener

  14-JUN-2011 17:28:39 * <unknown connect data> * (ADDRESS=(PROTOCOL=tcp)(HOST=192.168.1.5)(PORT=54171)) * establish * <unknown sid> * 12525
  TNS-12525: TNS:listener has not received client's request in time allowed
   TNS-12535: TNS:operation timed out
    TNS-12606: TNS: Application timeout occurred
  14-JUN-2011 17:28:39 * (CONNECT_DATA=(CID=(PROGRAM=)(HOST=__jdbc__)(USER=oracle))(SERVICE_NAME=inara.snowdrop.com)) * (ADDRESS=(PROTOCOL=tcp)(HOST=192.168.1.5)(PORT=54168)) * establish * inara.snowdrop.com * 0
  14-JUN-2011 17:28:39 * (CONNECT_DATA=(CID=(PROGRAM=)(HOST=__jdbc__)(USER=oracle))(SERVICE_NAME=inara.snowdrop.com)) * (ADDRESS=(PROTOCOL=tcp)(HOST=192.168.1.5)(PORT=54166)) * establish * inara.snowdrop.com * 0
  14-JUN-2011 17:28:39 * (CONNECT_DATA=(CID=(PROGRAM=)(HOST=__jdbc__)(USER=oracle))(SERVICE_NAME=inara.snowdrop.com)) * (ADDRESS=(PROTOCOL=tcp)(HOST=192.168.1.5)(PORT=54165)) * establish * inara.snowdrop.com * 0
  14-JUN-2011 17:28:39 * (CONNECT_DATA=(CID=(PROGRAM=)(HOST=__jdbc__)(USER=oracle))(SERVICE_NAME=inara.snowdrop.com)) * (ADDRESS=(PROTOCOL=tcp)(HOST=192.168.1.5)(PORT=54158)) * establish * inara.snowdrop.com * 0
  Tue Jun 14 17:28:59 2011
  14-JUN-2011 17:28:59 * (CONNECT_DATA=(CID=(PROGRAM=)(HOST=__jdbc__)(USER=oracle))(SERVICE_NAME=inara.snowdrop.com)) * (ADDRESS=(PROTOCOL=tcp)(HOST=192.168.1.5)(PORT=54161)) * establish * inara.snowdrop.com * 0
  14-JUN-2011 17:28:59 * service_update * inara * 0
  14-JUN-2011 17:28:59 * service_update * inara * 0

  Could someone give me a pointer on how to solve this?
  
  Kind regards
  Val

  Hi Valerie,

  ... not easy to distance :-(

  The tnsping should work - I have known nothing that this command was suspended. I've never known such problems in GC...

  "But perhaps article ID ' unable to connect to the database: connection failure may be due to a slow network, or the presence of an intermediate firewall" setting up data in the grid control [1074643.1 ID] "MOS might be useful.

• Communication problem between asynchronous process BPMN

  Hello, I have problems with communication between the two BPMN processes with an interface assynchronous.
  
  
  I have a main process BPMN (process a) and on the inside, I send task to call a second method BPMN (B). The two processes are inside the same project JDev.
  
  B BPM process was created using the JDev Assistant. I chose an asynchronous service and set the input and output variables. In the process of creating, I checked the start and end events (on the implementation tab) and the two are defined corretcly. In the process composite.xml B has 2 operations on Services exposed (left) side.
  
  A process, within the implementation of Task tab send, I selected:
  Type of conversation: lance
  Properties
  -Implementation: appeal process
  -Process: I can browse and select B processes
  -Node: Nothing appears on the LOV.
  
  If instead of the send task I use a Service task I can select the node (node B process starts).
  
  I use versions 11.1.1.4 JDev and SOA/BPM.
  
  
  Can you help me? I'm doing something wrong?
  
  Thanks for your help.
  
  Published by: 861727 on May 26, 2011-09:12

  There is a known issue in 11.1.1.4 when calling another process (in the same project) using the send/receive activity. As you noted the start for the process called node is not displayed. The workaround is to use the event to throw the Message and Catch event Message. They have the same semantics of async as send/receive activity. You would use Service call since it is synchronous.

• T310 without IDRAC6 warns of IDRAC communication failure, unable to access the BMC configuration

  Hello

  I got through my company a T310 which has no IDRAC6 Express card or the company.

  The LCD screen remains white/black constantly (tried with a spare one, same result) and when starting, it signals a failure of communication IDRAC6, which is normal since there is no card, then it restarts once more before entering Windows very well. He never offers me to enter a BMC configuration utility. I tried to reset the settings of the default BIOS nothing helps. OMSA reports no problem. Also updated the BIOS to the latest version 1.8.2 without modification. Fan is very noisy and I understand that by updating the BMC firmware, I have a chance to correct it, but I can't get into any configuration of the BMC.

  In my view, there was a map iDRAC6 before, but it is no longer, so don't know how to clear this error. I read that an iDRAC6 Express card is OPTIONAL, so it shouldn't bother me on this subject.

  ==> I want to erase those mistakes to POST, being able to update BMC firmware (or iDRAC) so that I can get the fan to operate at acceptable noise levels.

  (1) how do the server to understand that there is no. IDRAC whatsoever and give me access to the BMC during POST configuration utility?

  (2) is it normal that the remains of white LCD Panel at any time? Start button / stop works very well, just none of the buttons works, never get any color/light. Is it possible that it is controlled by the IDRAC/BMC, which, in its current mess, can't drive? I understand that the LCD comes with the option Connect hot (not sure why btw), so that I think it should work regardless of the IDRAC are there or not.

  I'm ready to buy an IDRAC6 Express card if there is a good chance that he will address this problem by eliminating the communication error and perhaps give me access to the config of the IDRAC. But I would really like to understand what's happening before you spend more money on it.

  Thank you!

  Max

  Hi Max,.

  The question might actually be caused by a problem of motherboard, a functional PowerEdge server without IDRAC should not show the error message, more if the Ctrl + E option is not displayed during POST, it indicates an abnormal start of BMC.

  Are what OS you running on the system? I don't know if you're aware, but the BMC update can be applied to the level of the OS, which are available here:

  http://Dell.to/HIBoTI

  If the system is still under warranty, I highly recommend asking for you assistance and support if a motherboard replacement is required.

  Thank you.

  Best regards

  DC Lim

  Reference Dell | Outreach services social - business

  Follow @DellCaresPro on Twitter: www.twitter.com/DellCaresPro

• Bluetooth data transfer between two laptops

  I have the model of laptop (5200-701) and it built in (PA3121U-1BTM) Bluetooth device & softwrare version is (1.02.17). It works well, but I could not transfer any file document or movies to any other computer that has Bluetooth technology, do not, weather me Bluetooth software device that supports it or not. Also please tell me what software version update me if available Bluetooth device?

  Hello

  If you want to check this page http://aps.toshiba-tro.de/bluetooth/

  Good bye

• SQL and shared Variable communication failure when you run an .exe application

  Salvation OR engineers,

  I'm faced with a problem. I have already tried almost everything under my bottom to solve, but I just couldn't get over it.

  I have a VI on my PC accessing a SQL database via the connection string and some share of variables in a server. Both shared variables and the SQL database are on the same server. There is a firewall between this server and my PC and the server is located in a DMZ environment.

  Design Labview environment, everything works fine. Even when I run the .exe on this computer file, everything works fine. But, when I created an application and install it on another computer, it just doesn't work.

  I'm using Labview 2013.

  Someone of you can help me with this bug?

  Thanks in advance!

  Hello world

  Back to share with you the solution:

  The problem was with the "SQL Native Client". Windows 7 doesn't have it as a default installation, if the application could not find the OLE DB provider for ODBC drivers. After installation, the connection has been established.

  As the server was within a demilitarized zone, I had to open some specific ports as follows:

  UDP/1434

  TCP / / 2343,49163

  59110-59115

  In fact, I have not experienced problems with the OAS. The error was generated when you try to connect to the database and sent to the rest of the code through the cluster of the error.

  Thanks for the support!

  Best regards to everyone.

  Luiz

• Wireless network problem: disconnects randomly anywhere between 1 and 4 hours.

  I have a wireless network problem, it disconnects randomly anywhere between 1 h and 4 h. The network consists of a Samsung 4 G hotspot and a Linksys AE1000. The signal strength is excellent, the AE1000 is 1 ft of the computer and 1 ft of the HotSpot.  The computer is a Dell Dimension 2400. Any ideas?

  Hi Jack,

  Problem solved.  I did 2 assumptions about the original problem.  I assumed that the 2 Tech that I spoke made the hurt their product. Battery saver has been activated on the hotspot.

  Thanks again

  Greg

• HP 15-r033 tx: USB, bluetooth, communication controller drivers bus controllers simple pci

  

  Hello:

  You need these drivers...

  Bluetooth:

  http://h20566.www2.HP.com/hpsc/SWD/public/detail?swItemId=ob_130390_1

  PCI:

  http://h10025.www1.HP.com/ewfrf/wc/softwareDownloadIndex?softwareitem=ob-130094-1&cc=us&DLC=en&LC=en&OS=4063&productOid=7308901&sw_lang=

  USB:

  http://h10025.www1.HP.com/ewfrf/wc/softwareDownloadIndex?softwareitem=ob-134312-1&cc=us&DLC=en&LC=en&OS=4063&productOid=7308901&sw_lang=