BSOD loading phone

Similar Questions

• Satellite C660 - Windows 7 64 bit BSOD after upgrade RAM

  Hi guys

  my laptop Specs: Satellite C660-1JG
  -Genuine Windows® 7 Home Premium 64-bit (pre-installed, Toshiba-HDD recovery)
  -Intel® Celeron® Processor T3500
  -2048 MB of RAM DDR3 (800 MHz).

  recently I increase my RAM to 4 GB (2 + 2 GB), since its installation, as soon windows7 64 bit beginning of loading, finished with BSOD. load BSOD Windows sometimes very well, but in a minute or two appears. I can confirm that it does not read the total RAM of 4 GB, I checked while the laptop was about 2 to 3 minutes ON. then I go out 1 RAM stick laptop is fine, no BSOD!

  so question raises if the RAM is at fault, incompatibility etc, but I have the dual boot OS and other OS is Ubuntu 11. who reads the 3.84 GB RAM and without crashing or BSOD or any question.

  Then I installed Windos 7 32 bit to see if that still has problems with 4 GB of RAM, but NO, 32 bit reads RAM 4 GB (usable 2.8 GB). without crashing or BSOD with 32, only problem with windows 64-bit version!
  I checked the specification it says Max RAM 4 GB Ram and yes it supports 4 GB RAM with Linux and win7 32-bit.

  I tried to update BIOS version 1.20 (currently on 1.40), but still got error: Firmware has no support of Flash (AFUWINGUI).
  I was wondering if any of you can guide me to the right direction.
  Thanks in advance
  Concerning

  I can't say for sure, but perhaps BSOD due to a compatibility issue.
  What RAM you bought as add-on (brand and specification)?

• Where can I find what kind of phone charges are compatible with the CMF?

  I've recently updated one of our CME to CME v10.0 systems

  I noticed that even if CMEv10 the Firmware support page shows how compatible phone for my 7911 phones is 9-2-1TH1-13,

  My 7911 running load phone 8-4-3-16 that all seem to be save and it works very well.

  So I must conclude that 7911 phone charging 8-4-3-16 is compatible with GCE v10.0

  Where can I go to find out what kind of phone charge versions are compatible with GUY or perhaps, at least, where I can find loads what kind of phone are no longer supported by a version of the CME?

  Hi Jared,

  Specific versions of CMF are tested with the versions listed on the doc "requirements" as you mentioned (linked below), but are not limited to these versions of firmware. The phone charges/firmware is completely independent of the CME/IOS version. And it is often appropriate to upgrade or downgrade the firmware of the phone on CME levels and is fully supported :)

   
  http://www.Cisco.com/en/us/docs/voice_ip_comm/cucme/requirements/guide/c...

  I would look at the upgrade of the firmware 8-4-3 for the 7911 BUT you need go to an intermediate version of the midpoint as 8-5-2 at first because of the "important notes" below;

  Questions for SCCP firmware update

  Note for all the firmware updates SCCP firmware version versions prior to 8.3 (3) for version 8.5 (3) or higher, you must first upgrade your firmware to version 8.5 (2). Once you have upgraded to version 8.5 (2), you can upgrade your IP phone to version 8.5 (3) or later.

  http://www.Cisco.com/en/us/docs/voice_ip_comm/cuipph/firmware/8_5_3/English/release/notes/7900_853.html#wp57602

  See you soon!

  Rob

• HP MIni 110 - Bios has no option of disk hard sata/IDE

  Hello

  My HP Mini (Win xp home ELCPC HP) can not load in windows because there missing files during startup. So I decided to repair the windows.

  However, I have some problems to load WIn XP Home CD SP2 (not ELCPC HP) at the start. I used closure of IDE - USB hard disk by replacing with CD-ROM instead of hard disk because HP Mini has no optical drive

  The CD has been loaded, but when halfway incoming to the windows installation, I got the BSOD after F6, pilots and BSOD loading to the 'Setup starts windows..".

  The error message was something like this:

  "Search for viruses on your computer. Remove any newly installed hard disk or hard disk controllers. Check hard drive are correctly installed and configured. Use CHKDSK /F to check for hard drive corruption, and then restart your computer.

  Technical information:
  "Stop: 0x0000007B (0xF7A22524, 0 x 0000034, 0x00000000, 0x00000000)"

  I browsed the site and found this recommendation to change from SATA HDD to IDE in BIOS. Strange thing is that I don't see this option in the BIOS. There is nothing a lot of option in the bios. I could only change the boot sequence, tool running, put in place under tension the password. That's all.

  No idea how to change the SATA to IDE hard drive in HP Mini 110? I would really appreciate your suggestion.

  I tried to restore but F11 / F10 takes me nowhere. Nothing happen after pressing these buttons. I wonder why the factory never create a copy for me restore my system if windows problem. I bought Win XP Home and Office, but no backup copy of the preload is created for the user when he is out of the factory. However, I am a little disappointed.

  In any case, would like to hear from any of you on the issues.

  See you soon!

  Have you tried the F6 key to go to Roxio BackOn Track to retrieve?

   

  http://support.HP.com/us-en/document/c01805426

• CCP on Windows 10

  I had a strange question of the CCP after upgrade to Windows 10.  It connected to my SO - 01 G Docomo Z3 as it should.  But after trying to change contact or make a systematic backup, it does not work.  No contact can be loaded phone.  Backup app come normally but without jobs shown previous backup.  Also when click on back up, all normal, choice of backup have shown normally, but after having clicked then the file name, then and error com upward as home of capture.

  What is happening or PCC is not fully compatible with Win 10?  With Win 8.1, no problem what so ever!

  Try to re - start Z3 was no help.

  Thanks for any help!

  

  This problem is solved.  All of this because of the right administrator work incorrectly.  Windows all just dumb question.
  Thank you all who read this.

• Cannot connect the phone to the computer with usb (BSoD)

  When I put the usb cable to the computer immediately make a weird noise (such as electricity) and automatically "beeps" once, freezes and after 5 sec BSOD appears. I have LG P970 and Xp pro sp3 32-bit. I have a fix that worked for a while but then the problem happens again.  WHAT SHOULD I DO?
  Had the same thing with usb internet modem but I managed to fix that.
  Sorry for the grammar :)
  Can I just stopped bsod because my pc just can't burn down it's way to powerless. If you need more info, let me know that I am here 24-7, cause I need to send a file from phone to the pc in 2 days. so please help...

  We need the DMP file because it contains the single record of the sequence of events that led to the accident, what drivers have been loaded, and what has been loaded.

  If you are overclocking STOP

  You may be able to get the DMP files without crashing by booting in SafeMode (F8) with networking.

  Please follow these instructions to collect data against crashes and upload them here, to your Skydrive or a service such as Rapidshare file sharing.

  http://www.SysNative.com/forums/showthread.php/68-blue-screen-of-death-%28BSOD%29-posting-instructions-Windows-8-7-amp-Vista?p=303&viewfull=1#post303

  http://SysNative.com/0x8/BSOD_Windows7_Vista_v2.64_jcgriff2_.exe

  To allow us to help you with symptoms BSOD on your computer, download the contents of your folder "\Windows\Minidump".

  The procedure:

  * Copy the contents of \Windows\Minidump to another location (temporary) somewhere on your machine.
  * Zip up the contents of this folder
  Please, upload to skydrive or a file sharing service and put a link to them in your next post.

  Go to start > search/run > cmd > msinfo32 and include it in the upload

  To ensure the minidumps are enabled:

  * Click Start, in the search box, type: sysdm.cpl, press ENTER.
  * On the Advanced tab, click Startup and recovery... Settings button.
  * Make sure that automatically restart is unchecked.
  * Under the writing debugging information header, select image partial memory (256 KB) in the list box drop-down (varies from 256kb).
  * Ensure to that small Dump Directory is listed as % systemroot%\Minidump.
  * OK your way out.
  * Reboot if changes have been made.

  http://www.SysNative.com/forums/showthread.php/325-BSODs-but-no-dump-files

  http://www.osronline.com/article.cfm?article=545

  Please also go to start > run > msinfo32 and record the results.  Send it with the DMP files, thank you.

• How can I say ios10 music playing ONLY what is loaded on the phone?

  How can I say ios10 music playing ONLY what is loaded on the phone? There was a way under ios9, but I can't find anything on ios10. When I shuffle a kind (like ROCK that has only 4 artists, I chose it), I want to shuffle only what is loaded on the phone, not what's on my mac (in the cloud)... I load only a few artists both because of space constraints. I have over 200GB of music on my mac...

  I don't want to see the playlists and artists who are not loaded on the phone either, but I can't find how to solve either!

  Launch the music application and go to the library > music downloaded. This shows that what is stored locally on the phone.

• Not charging with cell phones but computers to load adapter

  Hello

  I have iPhone 6 more.  I am having some problems. My phone will not charge with laptops, computers desktop or Mac Book. But she sees a power adapter. I tested with another official cable and also does not work. I tunes sync also does not work.

  Please help me solve this problem.

  Thank you

  Hello Win Htut Aung,

  I understand that you have had problems of load on several different computers and I want to help you get the issue resolved and isolated. Just for you help determine the cause could you let us know if your devices are still perceived by your computers, USB devices or iTunes?

  If not you can try the steps outlined in this article: If iTunes does not your iPad, iPhone or iPod

  If the problem persists, let us know. The entire community is here to help.
  Best regards

• How to sync Gmail contacts with phone (able to import, unable to synchronize), contact load very slowly when I search.

  I can't synchronize my contacts with my Gmail account as android. Secondly, when I search contacts to get in touch with app to make a call, the result of research takes time to load. I want to search strict to be dispalyed fast. In addition, is their not deleate temporaty files phone system, as I did in my office to speed up its performance. When I try search for updates of error massage is appear saying - their was an error then cheking for updates.
  Details of the phone that I use: -.
  Phone model:-Intex cloud fx
  Software:-Intex_cloud_FX_V07

  Hmm OK, I searched the menu contacts and I see there is an import contacts button there. I guess that sync's like import and export again and again. So it can be done simply not automated at present.

• my phone is stuck on the load screen

  I was just on my phone and it glitches so I pressed the home page and lock button to restart and now it is stuck on the load with the apple logo screen, and I can't do anything else that turn it off but when I turn back goes back to the load up screen.

  Put your iPhone into recovery mode as described here.  You may try to go into recovery mode more than once to succeed.

  If you are unable to update or restore your iPhone, iPad or iPod touch - Apple supports

• Phone loads slowly

  Hello

  I had my phone 2-4 months. last night, it wouldn't load properly maintained will fresh off and back on. today when I put it in charge, he went and several times when he showed afterwards it began to charge the charge went down instead of to the top. I'm now using any other charger put it takes hours to load

  How do load you?

  Connect directly into a wall outlet with the manufactured (OEM) Original Apple equipment adapter with the right, or you use some other adapter 3rd part, in the wall? in a car? connected to a computer? another device? Chained with other devices to load from a single source? The phone turned off, is it running?

• My phone symbol does not appear, but my phone is in charge of the load.

  SO, I charge my iPhone 6 s with a different charging cable because I lost one that comes with the iPhone. I used this and other cables of loading for some time and my phone has worked well. There are a few days but my cool phone but there is no indication of this load. Green lightning does not appear and when you put asleep it still won't appear. Also, it does not sound perception but again once he is in charge. I also tried to use my iPhone charger 6 friends who is that material w / and charger Apple real but he still has the same problem. It is impossible to know its support besides waiting for the percentage to go upward. And it is updated to 9.3.3 help

  Hello

  Try following the steps here, including remove all debris from the charge socket:

  If your iPhone, iPad or iPod touch won't charge - Apple Support

• My iPhone does not load unless the cable is placed just to the right and the phone is still completely. Advice?

  Hey everybody. Since a few days, I have had a hard time charging my iPhone. It all started when my phone onto my computer. He suddenly began to vibrate, and the charging symbol flickered on and outside. Since then, I had to mess with the power cord plugged into the phone until it starts to load. Once it starts to load and remains always completely, is perfectly fresh. The problem is that I do a lot of work and outdoor recreation such as hiking, and I need to charge my phone on the road sometimes. But once I'm start moving the phone around, it does not load until I have reposition it. My phone had not been dropped, smashed, splashed with water, or something serious in several days or even several weeks before acting. This could be a software problem? I cleaned the inside of the charge socket and the charge lead works fine with other devices. I also restored the phone to factory settings and then restore a backup. Any advice would be appreciated.

  Clean the hole of the support and review it with a bright light. You must get it squeaky clean and without bending the rather delicate pins. And make sure that the bent pins.

• Satellite M60-164 - BSOD during the windows loading screen

  On startup, I get the blue screen of death during the windows loading screen.

  I don't have a recovery cd, only a cd of OS (windows xp SP1a), which shows the option to repair but prompts then insert the recovery cd, how and where can I get one of these!

  No matter what help get a restore for Toshiba Satellite M60-164 Pro cd would be much appreciated!

  I think I know why you get a BSOD.
  You said that you have installed the Win XP SP1a.

  You must Win XP SP2!

  If you wish, you can create a CD Win XP SP2 clean! How? It's very easy. You need the tool freeware nLite (google for it and how to use it).

  Using the nLite application you could create a new XP CD and could include SP2 in this CD. You can then use this disk to start!

  By the way; The Toshiba recovery disc can be ordered from the ASP

• I recently bought an iPhone 6s I have loaded with my iTunes support information (old phone an iPhone 5). Problem is that I now have a replica on both phones I have an Apple ID - how to change the apple on the new ID

  I recently bought an iPhone 6s I have loaded with my iTunes support information (old phone an iPhone 5). Problem is that I now have a replica on both phones I have an Apple ID - how to change the apple on the new ID

  What do you mean by 'repetition '?

  You use two phones? Or did you give the old phone to someone else? If you use two phones, one ID on both Apple is probably than most people. Before you give or sell an iOS device, you must sign in iCloud in settings > iCloud and restore the device as good as new.