C++ = > LV: array, pointer and memory problem

Similar Questions

• Toshiba A50-frequency of 106:FSB Bus and memory problem

  Hello
  I have a problem with my new Toshiba A50-106. There are Celeron M 1, 5 GHz inside. That all specifications for this processor FSB speed should be 4x100MHz and for my memory bus speed should be 2 x 133, but when I check in SiSoft Sandra 2004 I see 4x187MHz (748 MHz) FSB and the speed of the Bus of Mem 2x249MHz (4 98 MHz). I can't fix it myself, because there is no such option in the BIOS and there is no standard software from Toshiba.
  Consequence of this is the problem of the temperature of my cpu. It is on average 54 c in an idle state.
  Perhaps you have had the same problem or knows what is in him and you can help me.
  What is a temperature average of your Celeron M?

  Thank you in advance,
  Michael

  Hi michael,.

  to your first question, have you run Sandra 2004 in battery mode because in battery mode CPU manages to set the speed of the FSB and memory also bus speed!

  So, try once more on AC power mode and let me know the results.

  Also, you should check these results with different bechmarking systems because these programs work differently.

  @ temperature problem: there is problem o with 54 HP. The home page of intel, said a 125 C is the maximum and then the CPU stops automatically!

  Rudi Bye

• New PPr upgrade and memory problems now

  I upgraded my version of PPr CC 2015 20 days ago and I went back to make a project that I had previously worked on and made more than 3 weeks. Now, it will not be made and the computer is just running out of memory and encoding is abandoned. I am on Windows 7 with a 2 years old i7 processor and have been able to use the first Pro CC 2015 without problem until the upgrade to the latest version that came out about 20 days ago. Are there bugs that are being developed here? Thanks for any info. I had the project made out by removing all effects to make sure it was a memory problem and quite sure the file render out with effects off the coast. However, I could make with effects on before this update.

  Thanks for you response Brian.

  Can you remove the effects of light and then give it a shot? Effects of light seem to be common with those who have reported this problem.

  Thank you

  Regalo

• Performance and memory problem

  Location:
  
  Have a mapping in Informatica (SDE), who joins about 15 tables from the OLTP database to create the staging table. This process joins the tables such as accounts, orders, and control elements. Great process that joins with very large tables. The process has been running in about 18 minutes, a change has been made.
  
  Change:
  
  Added three additional tables in the join (account tables and references) to pull 5 new fields. Two of these paintings are large enough with the third being small.
  
  
  Question:
  
  Now, the process that was running in about 18 minutes is more than 8 hours to run. If I take the SQL mapping code and run it in SQL Developer, it runs less than a minute.
  
  Possible cause:
  
  Don't know what the problem is that suddenly caused the process to change so dramatically. One thought is that the addition of three new tables in the join can be maxing some Informatica cache in temporary memory (storage). Looking at the workflow and I noticed that the size of the buffer of DTM has been set to 36 m. Not sure if this aspect will have to be increased, or if there is another parameter that we need change. Any insight and help would be greatly appreciated.
  
  Thank you...

  Better find an Informatica forum with expert tool specific.

  See you soon
  David

• Diagnostics Windows network, the error reads 'Problem with wireless adapter or access point' and fails to solve the problem.

  «Problem with access point or wireless adapter»

  Hi, I just bought a new laptop & I have the extreme difficulty to stay connected to the internet. When I run Windows Network Diagnostics, error reads 'Problem with wireless adapter or access point' and fails to solve the problem. Help, please... Thank you, Maria

  HI Maria,

  ·         What operating system is installed on your computer?

  ·         You have installed the latest drivers for wireless network card?

  Follow the suggestions below for a possible solution:

  Method 1: Start your computer in a clean boot state in order to check if the applications of third parties or startup items is the origin of the problem.

  How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7

  http://support.Microsoft.com/kb/929135

   

  Note: After troubleshooting, make sure that you configure the computer to start as usual as mentioned in step 7 in the above article.

  Method 2: See these articles for solve wireless problems:

  Why can't I connect to the Internet?

  http://Windows.Microsoft.com/en-us/Windows7/why-can-t-I-connect-to-the-Internet

   

  How can I troubleshoot network card?

  http://Windows.Microsoft.com/en-us/Windows7/fix-network-adapter-problems

   

  Windows wireless and wired network connection problems

  http://Windows.Microsoft.com/en-us/Windows/help/wired-and-wireless-network-connection-problems-in-Windows

  Let us know if that helps.

• Function of memory in the loop control and Simulation - problem of the ODE Solver

  Hello

  I'm correctly using the control loop & simulation to simulate the behavior of what is essentially a shock absorber-spring-mass system. In the process of change in time (dt) is used to integrate an arbitrary value. I use a rack depending on memory to store the time, to calculate the change of time (dt).

  The simulation is quite complex, because of the precision required, not all the ODE solvers can all support. Currently I use the Adams-Moulton method, this works very well for the simulation. However, it cannot detect the change in time, the change is constantly zero. This problem has auto market by using an another ODE Solver, but then the simulation has been messed up instead (even when I listen to the step sizes and tolerances). So I'm pretty confident that Adams-Moulton is one of solver ODE best suited to the problem at hand.

  Is there another way to store the previous hour and use it calculate lag, that the use of the memory function? Everyone knows about these problems before?

  I did a lot of research of error using the probe, but I'm sure that there is a problem with the ODE Solver and memory function. See the image below, showing basic how is calculated the change in time.

  I'm pretty new to LabVIEW, so if there is something else I missed I would be happy to hear it.

  PS! I set the tolerance minimum step of size/relative and absolute for the Adams-Moulton to simulate the behavior of the system properly.

  Problem solved!

  It turns out that the ODE Solver has struggled because of two "table 2D find" used functions. This was created for the interpolation/extrapolation, which caused a problem constantly and the ODE Solver could not resolve correctly, so the functions of memory doesn't work does not correctly or the other.

  By increasing the table manually, I could use closest method instead, with also good results as interpolation.

• I looked under system restore points and the earlier it had was on March 27, which was still after that I got problems

  Good so my computer has some corrupted files... I looked under the system (Yes, including the section 5 days ago) restore points, and the earlier it had was on March 27, which was still after that I got problems... I want a later date... Help, please.

  Hello

  If there is no previous restore points until 27 March, including even more that 5 days more then they just do not exist

  and you can not do something which

  Follow these steps instead:

  Run the sfc/scannow command.

  http://support.Microsoft.com/kb/929833

  Use the (SFC.exe) System File Checker tool to determine which file is causing the problem and then replace the file. To do this, follow these steps:

  1. Open an elevated command prompt. To do this, click Start, click principally madeprograms,Accessories, right-clickguest, and then clickrun as administrator. If you are prompted for an administrator password or a confirmation, type the password, or clickallow.
  2. Type the following command and press ENTER:
     sfc/scannow

     The sfc/scannow command analyzes all protected system files and replaces incorrect versions with appropriate Microsoft versions

  If SFC detects the main problems it can't fix you may need to borrow a Microsoft dvd vista not an acer, HP etc. recovery disk and do a repair installation

  read the below tutorial on how to perform a repair installation

  http://www.Vistax64.com/tutorials/88236-repair-install-Vista.html

• Memory problems and questions related to the process

  Does this look just for you, because the modified memory does little until after I had computer problems and had to do a factory reset

  The operating system is Windows 7 64-bit edition SP1

  I disabled SuperFetch is told by the way, if this help anyone on this issue.

  Resource monitor

  

  Windows process

  

  Services

  

  

  

  Performance

  

  Hello

  When your computer doesn't have enough memory for all the actions it is trying to perform, Windows and your programs can stop working. To help prevent information loss, Windows will inform you when your computer is low on memory. You can also learn to recognize the signs of low memory and take measures to prevent the problem. Insufficient memory problems occur when your computer is running out of RAM and becomes virtual memory. This can happen when you run more programs that the RAM memory installed on the computer is designed to support. Low-memory problems can also occur when a program free up memory that it needs more. This problem is called memory overuse or a memory leak.

  You can consult the following Microsoft articles and check if it helps.

  Diagnosing memory problems on your computer

  http://Windows.Microsoft.com/en-AU/Windows7/diagnosing-memory-problems-on-your-computer

  Prevention of problems of memory

  http://Windows.Microsoft.com/en-AU/Windows/preventing-low-memory-problems#1TC=Windows-7

  You may receive an "Out of Memory" error message because of the limitation of in Windows Vista or Windows 7 desktop heap

  http://support.Microsoft.com/kb/947246

  Note: This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base: http://windows.microsoft.com/en-US/windows7/Back-up-the-registry

  I hope this helps.

  Please post back with the State of the question and we will be happy to help you further.

• PC freezes and Hardrive memory problems

  I have a hp g62 with windows 7 Home Edition on it

  Sometimes it blocks for awhile and then he unfrezzes then goes over and over again and I need a program to optimize my PC

  next lot of my windows files take a lot of space on my hard drive

  im a gamer and I need to have good performance and memory without it freezing and I had to remove a game 11FR because windows Scott files take a lot of space

  Here is my card and details they are (FORMAT HTML)

  http://sdrv.Ms/Kspugd

  the specification of two files are somewhat the same thing but better to check both

  Thank you

  Well, as a first step, you use two utilities questionable; SlimWare & IObit, if you used either to "optimize" your system or use the driver verifier, who knows what problems you have caused to your system.

  Uninstall both, before using an "undo" option, if programs have such.

  Visit the HP support for your model, then get the correct drivers

  Your C drive has enough free space (238 gb), victory uses 62 GB (which includes your libraries)

  Graphics of your laptop computer may not support some modern games, the game machine to will specify what graphics are needed.

• How to load a pointer data memory in table

  I'm trying to interface to a DLL used to manage a piece of hardware. The DLL is written in c. uses _stdcall and the Import Wizard has hooked up with success of most screws in a library; many of them work everything just as it is. I have also played with the knot of library function call and think that most of the time, I got the hang of it. I ran successfully for the odd Windows API call (e.g., MessageBox). However, I am a newcomer in Labview. My problem is related to a DLL function that requires a pointer to a block of memory, in which he then dealt with the material (in the form of table of UINTs) data. I want to display these data in Labview, through a table I guess. I think I found everything I need to do in terms of creating a table and hanging until the node of library function call with an input pointer.

  I hope this would work IF the block of memory has been fully completed until the function has returned. HOWEVER, this is not how the DLL function. It creates a thread that exert to put data in the memory block after the function in the DLL. Extra features are available for face to discover if the data transfer is complete. I guess this is enough to refute the marshaling of data in Labview, unless there is some special commands for this purpose.

  I thought maybe I should allocate the memory using the Windows API (LocalAlloc LPTR flagged so I get a pointer) and I wrote a little VI that allocates and releases the memory that seems to work. This way I can release memory when the transfer is complete. MY PROBLEM is, given the pointer to the block of memory, as returned by LocallAlloc, how can I get Labview to read the memory in an array of integers.

  I am now a little stuck and would like to receive advice on one, how to convert the block of memory, or on a way to approach things btter.

  TIA

  SteveJM wrote:

  So I have a working solution, which is basically the same idea as your suggestion, but uses the Windows API. I took the trouble to mention it, but when I looked more closely at 'MoveBlock', 'DSNewPtrt' etc, I realized that they are a static C library. This means that using them requires that you have a C development system and knowledge how to build DLLs on that. As it happens that causes me a problem, but it seemed like a hammer in this case because the routines you need are already in the kernel32.dll module. [Yes that makes specific Windows, but then you would need rebuild your dll for each operating system in any case].

  This paragraph is completely inaccurate.  These functions are integrated into the runtime LabVIEW, without which your LabVIEW code will not work.  You have the guarantee that if you can run your LabVIEW code, or in the development environment or as a compiled application, these functions are available.  No need for a C development system (if that were the case, don't you think someone would have mentioned in one of the many messages on this forum on the use of MoveBlock?).

  SteveJM wrote:

  It is true that you need to find a way to pass the pointer to the destination of reference. In other words, using a "handful" I guess. One of the difficulties is that the documentation for Labview is rather imprecise on what happening coming in and out of the function call. Unfortunately, the meaning of "Handle" is very dependent on context, so documentation should be much more detailed. If you select 'Manage' rather than "Pointer table" minimum size box disappears implying that Labview will take a pointer to a pointer to a format of Labview. It would then allow the size information in the allocation of the table and set the offset pointer approprately when passing a pointer to the function that would fill the memory. If the size of the table was large enough, it might be useful to tweak with this to avoid the copy useless (and allocation), but I don't have time now, unless I find the best literature which explicitly explains this gathering takes place for each option in the dialog box.

  All the help you need is available.  Set up a call library function node to pass by handle, close the configuration dialog box, right-click on the function call library node and choose Create .c file...  You will get a draft of C with all structs defined for you, and you will see that the handful of LabVIEW table includes size information.  There is no "triage."  He is just passing pointers autour (and a few and Word-permutation of bytes due to problems of "endianness").  When you pass an array of pointer to array value, you get what you expect - LabVIEW dereferences the handle once and passes the pointer of table.  It's exactly like a C function call.  Nothing unusual occurs when the call is returned (with the exception, even once, "endianness" switch if necessary).  That said, it's a bad idea to do what you want to do with a handle, because LabVIEW is allowed to move the table when he likes and has no way to know that some other functions still has this memory block to stay where he is.

• When connecting on MacMini, password is auto-complete with a myriad of points and is not the right password

  When connecting on MacMini after I click on the user, the password field is auto-complete with a myriad of points and is not the right password.

  There suddenly / maybe after the most recent update 2015-008, which I installed it on 8 January 2016.

  I need to delete points, usually I can remove them by double clicking on it and pressing the delete key, but they will not simply remove by clicking in the field and using the delete key, as would be normal. Sometimes it takes a few tries to remove the points, and then I can connect.

  Does my keyboard or a virus, my usb port, the update of security or something else...?

  I use this computer without problem for a few years.

  Thank you, Kathy

  osX version 10.9.5 processor 2.3 GHz intel core 17

  First try another KB

  Next

  -Try to reset memory NVRAM/PRAM and SMC

  MacIntel: Reset of the controller (SMC) system management

  Subject of memory NVRAM and PRAM

  -Try to start safe mode

  OS x: what is Safe Boot, Safe Mode?

  -Start to recovery and repair the startup disk

  OS X: on OS X Recovery - Apple Support

  -If it is repairable reinstall the OSX

  How to reinstall OS X on your Mac - Apple Support

  -If you do not have a backup using disk utility to restore the internal drive to an external drive, so that you can try to recover the data.

  Format the boot disk and then do a fresh install of Mac OS x

• Computer says disk C and F are weak and memory Windows is very low. and I have the same thing in so many programs.

  I have windows xp home edition, he received from a friend. Tells me disk C and F are close to full. Make cleaning disc, but not enough. AND says the window is very low on storage space. Don't know what to delete and keep programs are

  http://Windows.Microsoft.com/en-us/Windows-Vista/preventing-low-memory-problems

  Read what you and answer a few questions about your system:

  1. What is your current antivirus?

  2.

  Click Start, run and enter in the box:

  Msinfo32

  Click OK, and when the system info summary appears, click on edit, select all (Ctrl-A), copy (Ctrl-C) and paste (Ctrl-V) the information back here in your next reply.

  You can change the personal information.

  3. look in disk management, how many partitions? How much free space on each?

  4. optimize your pc:

  Stanley Zhang tips

  Search for malware:

  Download, install, execute, update and perform analyses complete system with the two following applications:

  ·                                 MalwareBytes (FREE)

  ·                                 SuperAntiSpyware (FREE)

  Remove anything they find. Reboot when necessary. (You can uninstall one or both when finished.)

  Search online with eSet Online Scanner.

  The less you have to run all the time, most things you want to run will perform:

  Use Autoruns to understand this all starts when your computer's / when you log in. Look for whatever it is you do not know usingGoogle (or ask here.) You can hopefully figure out if there are things from when your computer does (or connect) you don't not need and then configure them (through their own built-in mechanisms is the preferred method) so they do not - start using your resources without reason.

  You can download and use Process Explorer to see exactly what is taking your time processor/CPU and memory. This can help you to identify applications that you might want to consider alternatives for and get rid of all together.

  Do a house cleaning and the dust of this hard drive:

  You can free up disk space (will also help get rid of the things that you do not use) through the following steps:

  Windows XP should take between 4.5 and 9 GB * with * an Office suite, editing Photo software, alternative Internet browser (s), various Internet plugins and a host of other things installed.

  If you are comfortable with the stability of your system, you can delete the uninstall of patches which has installed Windows XP...
  http://www3.TELUS.NET/dandemar/spack.htm
  (Especially of interest here - #4)
  (Variant: http://www.dougknox.com/xp/utils/xp_hotfix_backup.htm )

  You can run disk - integrated into Windows XP - cleanup to erase everything except your last restore point and yet more 'free '... files cleaning

  How to use disk cleanup
  http://support.Microsoft.com/kb/310312

  You can disable hibernation if it is enabled and you do not...

  When you Hibernate your computer, Windows saves the contents of the system memory in the hiberfil.sys file. As a result, the size of the hiberfil.sys file will always be equal to the amount of physical memory in your system. If you don't use the Hibernate feature and want to reclaim the space used by Windows for the hiberfil.sys file, perform the following steps:

  -Start the Control Panel Power Options applet (go to start, settings, Control Panel, and then click Power Options).
  -Select the Hibernate tab, uncheck "Activate the hibernation", and then click OK. Although you might think otherwise, selecting never under "Hibernate" option on the power management tab does not delete the hiberfil.sys file.
  -Windows remove the "Hibernate" option on the power management tab and delete the hiberfil.sys file.

  You can control the amount of space your system restore can use...

  1. Click Start, right click my computer and then click Properties.
  2. click on the System Restore tab.
  3. highlight one of your readers (or C: If you only) and click on the button "settings".
  4 change the percentage of disk space you want to allow... I suggest moving the slider until you have about 1 GB (1024 MB or close to that...)
  5. click on OK. Then click OK again.

  You can control the amount of space used may or may not temporary Internet files...

  Empty the temporary Internet files and reduce the size, that it stores a size between 64 MB and 128 MB...

  -Open a copy of Microsoft Internet Explorer.
  -Select TOOLS - Internet Options.
  -On the general tab in the section 'Temporary Internet files', follow these steps:
  -Click on 'Delete the Cookies' (click OK)
  -Click on "Settings" and change the "amount of disk space to use: ' something between 64 MB and 128 MB. (There may be many more now.)
  -Click OK.
  -Click on 'Delete files', then select "Delete all offline content" (the box), and then click OK. (If you had a LOT, it can take 2 to 10 minutes or more).
  -Once it's done, click OK, close Internet Explorer, open Internet Explorer.

  You can use an application that scans your system for the log files and temporary files and use it to get rid of those who:

  CCleaner (free!)
  http://www.CCleaner.com/
  (just disk cleanup - do not play with the part of the registry for the moment)

  Other ways to free up space...

  SequoiaView
  http://www.win.Tue.nl/SequoiaView/

  JDiskReport
  http://www.jgoodies.com/freeware/JDiskReport/index.html

  Those who can help you discover visually where all space is used. Then, you can determine what to do.

  After that - you want to check any physical errors and fix everything for efficient access"

  CHKDSK
  How to scan your disks for errors* will take time and a reboot.

  Defragment
  How to defragment your hard drives* will take time

  Cleaning the components of update on your Windows XP computer

  While probably not 100% necessary-, it is probably a good idea at this time to ensure that you continue to get the updates you need. This will help you ensure that your system update is ready to do it for you.

  Download and run the MSRT tool manually:
  http://www.Microsoft.com/security/malwareremove/default.mspx
  (Ignore the details and download the tool to download and save to your desktop, run it.)

  Reset.

  Download/install the latest program Windows installation (for your operating system):
  (Windows XP 32-bit: WindowsXP-KB942288-v3 - x 86 .exe )
  (Download and save it to your desktop, run it.)

  Reset.

  and...

  Download the latest version of Windows Update (x 86) agent here:
  http://go.Microsoft.com/fwlink/?LinkId=91237
  ... and save it to the root of your C:\ drive. After you register on theroot of the C:\ drive, follow these steps:

  Close all Internet Explorer Windows and other applications.

  AutoScan--> RUN and type:
  %SystemDrive%\windowsupdateagent30-x86.exe /WUFORCE
  --> Click OK.

  (If asked, select 'Run'). --> Click on NEXT--> select 'I agree' and click NEXT--> where he completed the installation, click "Finish"...

  Reset.

  Now reset your Windows with this FixIt components update (you * NOT * use the aggressive version):
  How to reset the Windows Update components?

  Reset.

  Now that your system is generally free of malicious software (assuming you have an AntiVirus application), you've cleaned the "additional applications" that could be running and picking up your precious memory and the processor, you have authorized out of valuable and makes disk space as there are no problems with the drive itself and your Windows Update components are updates and should work fine - it is only only one other thing youpouvez wish to make:

  Get and install the hardware device last drivers for your system hardware/system manufacturers support and/or download web site.

• HP/Compaq nc6400 laptop: HP/compaq nc6400 Windows 10 and graphic problem, erasing text in areas of immersive shell.

  I have a laptop nc 6400 product number: RB518UT #ABA uses an ATI mobility Radeon x 1300 graphics card, as well as Intel (r) mobile express chipset available 965 G. I chose to use Classic desktop windows at the moment and no problem at all now. I don't know about Vsync or 2D with any partbut I disabled it Aero, windows 'themes' clear the text, mosaic with not a spec left shaows WHEREAS I could think of and still the text clears using my own slider like gum or disappears and leavesablank. Alsooccasionaly gibberish are more black lines not only any official language, but today I thought that almost a nonsense post script type to some... in some mobile tiles that can refresh, but even that does not work as it always has... I am at a loss I need a decent graphics that I use photoshop and dreamweaver allt/times a day and at least they need to exploit as much as possible. I had no problem with their execution on this computer for the past 4 years or more. It has been now 4 OS on this big machine that has not had any problems over the past 7 years. He 4gig memory and 750 GB hard drive and lack of wellis touchscreen but... not worry Windows when they checked all this to check.  I am beyond my capabilities and need help. Even if I need to build my own divers I Although it will not be the fastest answer, but I can see the need to know how the alter pilots an asset right about now.  Please you all the

  suggestions will be an asset, as I am a "what to do now the level of frustration"and would like that much more about the reason for it. " I was just as lucky as my machine has never had issues that were close to that sort of thing.

  TY for any help, answers, all possible assistance, you may think.  I hope that I have provided a clear problem, and most of the information you need. I never used a service like other instances, that raising any issues that others have as well.  Always helping if I wasn't sure but never as difficult a question as is happening now.

  Ty for any possible assistance or suggestions that can point me in the right direction.

  egcorrell

  Hello:

  The only suggestion I can offer would be manually install the graphics driver Vista support for your laptop and driver, page and see if it works...

  BTW, the nc6400 has the mobile Intel 945 chipset, not the 965.  The 6910p has the 965 chipset.

  Download and run this driver... You will probably get an error of unsupported operating system.

  http://h20565.www2.HP.com/hpsc/SWD/public/detail?sp4ts.Oid=1847705&swItemId=ob_59975_1&swEnvOid=2103#tab1

  Conclusion of any windows error.

  Go to Device Manager and click on the video controller (or Microsoft based Display Adapter) who need drivers.

  Click the driver tab.

  Click on set to update driver.

  Select her browse my computer for driver software option and navigate to the folder of the driver that was created when you ran the file.

  This file will be located in C:\SWSetup\sp38833.

  Make sure that the include subfolders is selected and see if the pilot goes like this.

  Then restart.

  If your nc6400 has this problem with the SMSC Infrared driver with the! Marc, I went into the BIOS, found the menu of Ports and disabled the infrared port, saved and restarted.

  That got rid of the problem of device.

  I don't know of anyone who uses the infrared port anyway.

• Jumping mouse pointer and Vista "busy circle" using WMP

  When I plug in a "memory stick" SanDisk, WMP trying to 'sync', 'something something '.  The mouse pointer and the Vista 'busy circle' jumping around.  I disabled the auto-start, I deleted the box "Start synchronization when the device connects" and I tried all the options in Sync Center.  WMP recognizes the different sizes of "memory sticks" and each is full.  Sometimes, the "memory sticks" shows in the library list.  I ended up the sync on a partnership, but this command is grayed out on the other.  The side "edit" of WMP sometimes shows the "memory stick" he said here drag the items to synchronize.  Sometimes the side "edit" of WMP says "connect the device.  Once in about 50 tries, WMP actually synchronize with the "memory stick".  I use the memory sticks for data transfer and storage only.  I NEVER want anything to synchronize!  I'm from the old (old, old, old read) school, so if I want something copied, I will use the copy command.  I've seen similar problems here and tried the solutions provided, unfortunately, nothing seems to work.  HELP PLEASE!
  TYVM!

  After the cohabitation on maybe 10 different forums, I came across an apparent solution.
  Apparently, the "guilty" is the Portable device enumerator Service.
  When I disabled it, my problems went away.

  Follow this step to turn off the service.

  1. click Start and type services.msc in the start search box and press on enter.

  2. scroll through the list and select the service.

  3. right click on the service and choose the Propertiesoption.

  4. you can change the Startup type to disable or the status of the service to stop.

  Good luck to all!
  Ed

• Memory problem, PAGE_FAULT_IN_NONPAGED_AREA 0 x 00000050!

  Hello!

  So I have two sticks of memory, one is broken and the other one works fine. I tested the one broken in the PC because I thought it wasn't beoken at the time. So after a few hours of use PC everything has stopped working, got BSOD etc. I unplugged the a RAM that is now broken and after ive got BSOD with the following code PAGE_FAULT_IN_NONPAGED_AREA 0 x 00000050! PAGE_FAULT_IN_NONPAGED_AREA bug control has a value of 0 x 00000050. This indicates that invalid system memory was referenced.
  How can I fix? I used 4 x 2 GB ram ddr3, atm, I use a stick of ram to 4 GB.
  Would love your help, thank you!

  Hello

  Well the two sticks could be bad. Don't forget to test the memory very carefully. See memory
  Test methods in the next message.

  ==========================================================

  Resolve errors stop (blue screen) in Windows 7 - has a section for if you can or cannot start Windows.
  http://Windows.Microsoft.com/en-us/Windows7/resolving-stop-blue-screen-errors-in-Windows-7

  For BlueScreen troubleshooting methods using BlueScreenView and MyEventViewer see my
  answers if this thread - top 3 RESPONSES (+ 1 other).

  http://answers.Microsoft.com/en-us/Windows/Forum/Windows_7-system/sometimes-i-get-a-blue-screen-when-using-IE-8/c675b7b8-795f-474d-a1c4-6b77b3fcd990

  We can analyze the minidumps if make you it available to the SkyDrive or another file
  sharing sites (such as MediaFire). If you have problems to download the copy of minidumps
  for the office or in the Documents folder and download them from there.

  ZIP or download the content of the C:\Windows\minidump

  Use SkyDrive to upload collected files
  http://social.technet.Microsoft.com/forums/en-us/w7itproui/thread/4fc10639-02dB-4665-993a-08d865088d65

  --------------------------------------------------------------------------------------------------

  BCCode: 50 0 x 00000050

  References to Vista also apply to Windows 7.

  Have you recently added any hardware? Have you updated a driver just before
  These began? (Check control panel - updates of Windows to see if all drivers
  have been updated it there all the time, it started) main likely culprits are video
  pilot, other great drivers, memory and antivirus/antispyware/security products
  could be faulty as well as reader questions.

  Use the troubleshooter below and refer to the following message for pilots and
  memory when you get these sections and then return of the disease.
  game needed.

  BCCode: 50 0 x 00000050

  Bug Check 0 x 50: PAGE_FAULT_IN_NONPAGED_AREA

  PAGE_FAULT_IN_NONPAGED_AREA bug control has a value of 0 x 00000050. This indicates that invalid system memory was referenced.

  Important info if you received a STOP Code

  If you received a blue error screen, or a stop code, the computer stopped abruptly to protect against data loss. A hardware device, its driver or software might have caused this error. If your copy of Windows is shipped with your computer, contact your computer manufacturer. If you have purchased
  Windows separately from your computer, Microsoft provides support. To find contact information for Microsoft or the manufacturer of your computer, Contact Support.

  If you have experience with computers and try to recover from this error, follow the steps in the Microsoft article solution STOP (blue screen) errors in Windows.

  These actions could prevent a mistake like this does not happen:

  1. Download and install updates for your computer from Windows Update device drivers.
  2. Scan your computer for computer viruses.
  3. Check your hard drive for errors.

  PAGE_FAULT_IN_NONPAGED_AREA parameters

  The following settings are displayed on the blue screen.

  Parameter	Description
  1	The referenced memory address
  2	0: Read operation 1: Write operation

  3

  Address that referenced memory (if known)

  4

  Reserved

  If the driver responsible for the error can be identified, its name is printed on the blue screen and stored in memory location (PUNICODE_STRING) KiBugCheckDriver.

  Cause

  Bug control 0 x 50 usually occurs after the installation of a faulty hardware or installation failure of material (usually associated with defective RAM, either main memory, L2 RAM or RAM video cache).

  Another common cause is a defective system service installation.

  Antivirus software can also trigger this error, as can a corrupted NTFS volume.

  Resolution

  
  Fix a defective hardware problem: if the material has been added to the system recently, remove it to see if the error recurs. If the hardware failure existing, remove or replace the faulty component. You must run the diagnostics of material provided by the manufacturer of the system. For more information about these procedures, see the manual of your computer.

  
  Fix a defective system service: disable the service and confirm that this resolves the error. If so, contact the manufacturer of the system service on a possible update. If the error occurs during the system startup, restart your computer, and then press F8 to menu mode characters that displays the choice of operating system. In the Windows Advanced Options menu that results, select the last known good Configuration option. This option is most effective when a pilot or a service is added at a time.

  
  A problem of antivirus software: disable the program and confirm that this resolves the error. If this is the case, contact the manufacturer of the program about a possible update.

  
  Fix a corrupted NTFS volume: run Chkdsk /f /r to detect and repair disk errors. You must reboot the system before the start of the analysis of disk on a system partition. If the SCSI hard disk, check the problems between the SCSI controller and the drive.

  Finally, check the system log in Event Viewer for additional error messages that might help determine the device or driver that generated the error. Disable the cache in memory of the BIOS might also resolve it.

  Remarks

  In general, this address is in the released memory or simply not valid.

  This cannot be protected by a try - except Manager - it can only be protected by a probe.

  BCCode: 50 0 x 00000050<-- read="" this="">
  * 1095.html? order = votes http://www.faultwire.com/solutions-fatal_error/page-fault-in-NONPAGED-Area-0x00000050-

  =========================================

  Look in the Event Viewer to see if something is reported on those.
  http://www.computerperformance.co.UK/Vista/vista_event_viewer.htm

  MyEventViewer - free - a simple alternative in the standard Windows Event Viewer.
  TIP - Options - Advanced filter allows you to see a period of time instead of the entire file.
  http://www.NirSoft.NET/utils/my_event_viewer.html

  -------------------------------------------------------------------------

  Here are a few ways to possibly fix the blue screen issue. If you could give the blue screen
  info that would help. Such as ITC and 4 others entered at the bottom left. And all others
  error information such as codes of STOP and info like IRQL_NOT_LESS_OR_EQUAL or PAGE_FAULT_IN_NONPAGED_AREA and similar messages.

  As examples:

  BCCode: 116
  BCP1: 87BC9510
  BCP2: 8C013D80
  BCP3: 00000000
  BCP4: 00000002

  or in this format:

  Stop: 0 x 00000000 (oxoooooooo oxoooooooo oxoooooooo oxooooooooo)
  Tcpip.sys - address blocking 0 x 0 00000000 000000000 DateStamp 0 x 000000000

  It is an excellent tool for displaying the blue screen error information

  BlueScreenView scans all your minidump files created during 'blue screen of death '.
  hangs and displays information about all accidents of a table - free
  http://www.NirSoft.NET/utils/blue_screen_view.html

  BlueScreens many are caused by old or damaged, in particular the video drivers drivers however
  There are other causes.

  You can do mode if necessary safe or the Vista DVD command prompt or
  Options recovery if your system is installed by the manufacturer.

  How to start on the System Recovery Options in Windows 7
  http://www.SevenForums.com/tutorials/668-system-recovery-options.html

  You can try a system restore to a point before the problem started when one exists.

  How to do a system restore in Windows 7
  http://www.SevenForums.com/tutorials/700-system-restore.html

  -------------------------------------------------------------------------

  Start - type this in the search box-> find COMMAND at the top and RIGHT CLICK – RUN AS ADMIN

  Enter this at the command prompt - sfc/scannow

  How to fix the system files of Windows 7 with the System File Checker
  http://www.SevenForums.com/tutorials/1538-SFC-SCANNOW-Command-System-File-Checker.html

  How to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe)
  program generates cbs.log Windows Vista (and Windows 7)
  http://support.Microsoft.com/kb/928228

  The log can give you the answer if there is a corrupted driver. (Says not all possible
  driver problems).

  Also run CheckDisk, so we cannot exclude as much as possible of the corruption.

  How to run the check disk at startup in Windows 7
  http://www.SevenForums.com/tutorials/433-disk-check.html

  -------------------------------------------------------------------------

  Often drivers up-to-date will help, usually video, sound, network card (NIC), WiFi, part 3
  keyboard and mouse, as well as of other major device drivers.

  Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
  http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htm

  Installation and update of drivers under Windows 7 (updated drivers manually using the methods above
  It is preferable to ensure that the latest drivers from the manufacturer of system and device manufacturers are located)
  http://www.SevenForums.com/tutorials/43216-installing-updating-drivers-7-a.html

  Stop Windows 7 to automatically install device drivers
  http://helpdeskgeek.com/Windows-7/stop-Windows-7-from-automatically-installing-device-drivers/

  How to disable automatic driver Installation in Windows 7 / Vista
  http://www.AddictiveTips.com/Windows-Tips/how-to-disable-automatic-driver-installation-in-Windows-Vista/

  Turn off Windows Update Device Driver search prompt in Windows 7 / Vista (for professionals,
  Ultimate and Enterprise)
  http://www.AddictiveTips.com/Windows-tips/disable-Windows-Update-device-driver-search-prompt/

  -------------------------------------------------------------------------

  How to fix BlueScreen (STOP) errors that cause Windows Vista to shut down or restart
  quit unexpectedly
  http://support.Microsoft.com/kb/958233

  Troubleshooting Vista Blue Screen, error of JUDGMENT (and Windows 7)
  http://www.chicagotech.NET/Vista/vistabluescreen.htm

  Understanding and decoding BSOD (blue screen of death) Messages
  http://www.Taranfx.com/blog/?p=692

  Windows - troubleshooting blue screen errors
  http://KB.wisc.edu/page.php?id=7033

  -------------------------------------------------------------------------

  In some cases, it may be necessary.

  Startup Options recovery or Windows 7 disk repair

  How to run a startup repair in Windows 7
  http://www.SevenForums.com/tutorials/681-startup-repair.html

  How to start on the System Recovery Options in Windows 7
  http://www.SevenForums.com/tutorials/668-system-recovery-options.html

  How to create a Windows 7 system repair disc
  http://www.SevenForums.com/tutorials/2083-system-repair-disc-create.html

  How to do a repair installation to repair Windows 7
  http://www.SevenForums.com/tutorials/3413-repair-install.html

  I hope this helps.

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle=""><- mark="" twain="" said="" it="">