CAN Bus Analyzer

Similar Questions

• Satellite M100 - I can't analyze the CPU temperature

  I am a Toshiba Satellite M100 series owner (Core Duo T2300, X 1400, etc.). The problem is that I can't analyze the CPU temperature variations in such popular application such as Everest or Notebook Hardware Control. Also any other software provided by Toshiba and installed already on my HARD drive does not include some CPU diagnostics, including temperature changes!

  The only software that seems to work is the HWiNFO32 so there is a thermal probe inside which specifies that Centrino Duo processor temperature, but this software is not very user-friendly :(

  There is a request for Toshiba do something with this... I've updated the BIOS in my template for a version 1.70, but this does not change I could easily noticed (or is he?)  :(

  Hello

  In most cases applications can give you info on the hardware and the different settings but the temperature of the CPU in most cases is not visible. Toshiba has no tool or utility that can read or modify.

  BIOS update has absolutely no influence on it. Satellite M100 is one of the latest devices and I really don t understand why it is so important to you. Important in my opinion is the stability of the system, the operation of the equipment and no problem with the software you are using. Am I wrong?

• CAN bus off fast recovery and recovery slow modes

  Hello

  I know the busoff recovery procedure consists of monitoring the CAN bus up to 128 11 consecutive recessive bit sequences have been observed.

  But I want to know what is the bus fast recovery and slow the recovery.

  Thanks in advance.

  Kind regards

  Sagar Joshi

  Where you see the terms "broad recovery fast bus" and "slow bus off recovery". As far as I know, the spec CAN define only a single bus out of recovery.

• Absolute Log Timestamp Converter CAN bus

  I'm experimenting with the help of the CAN Bus Log Converter to convert raw CAN bus data to a TDMS file to Signal/value data for analysis.

  My understanding is that the timestamp to the Raw features store the absolute timestamp (I checked the timestamps in my CAN messages are absolute), but after passing through the CAN Bus Log Converter, the weather channel seems to show only in the relative time (well... a relative number of seconds).

  By looking at the properties of the group or channel, I have the following:

  Group:

  CANDateTimeStamp - 25/09/2015 10:19:16

  POUVEZ stamp - 6.36103091565499E + 10

  Time string:

  Display format: Digital (it takes not time?)

  Minimum: 0

  Maximum: 63.40234 etc.

  I just started using DIAdem angry and I am currently trying a few things while working through online training.

  Hi Sam,

  I'm curious, were you angry before you start using tiara or DIAdem because frustrated you?  The Bus Log Converter creates a relative time for each message channel, but includes the absolute DateTime offset until a string of human time date readable and a number of seconds tiara.  If you add this huge number you mentioned to all layer of time values, and then change the channel of the digital display time display, you will get the absolute DateTime values.

  Brad Turpin

  Tiara Product Support Engineer

  National Instruments

• Reset of the CAN bus without knowing the reference of the tasks

  Hello everyone,

  I use the API CAN channel to read data from a CAN bus while at the same time taking measures using other DAQ devices. When my VI throws an error after the CAN bus has been initialized and started, try to kick start my VI will force the init-start CAN VI throw an error because the channel is never allowed.

  Is there a way to clean a channel CAN without having a special reference to the wire? Otherwise, how could I solve this problem?

  Thank you!

  Erik

  Hi Erik,

  Is the error that you are experiencing from the same service on a regular basis?  If Yes, what can be done before adding them to the whole application of error handling, you can add a case structure, use the cluster of error in this function to act as the selector for the structure of the case and add a Clear Channel command to the real case of the structure, followed by an error handler.

  Now, that being said, I still recommend using throughout the application, management errors, especially if this will be distributed as an executable file.  But for purposes of development, it is perhaps the fastest way to implement a clear failure of the VI function so that it restarts correctly on the next iteration.

  Kind regards

  -Dave C

• The CAN bus activity: why can I not see my CAN bus activity using MAX and a NI USB-8473?

  I use an NI USB-8473 and Measurement & Automation Explorer on a CAN bus I know works.   He does not see as a traffic CAN bus.

  Any ideas on how to trouble shoot to find out why this material does detect any signals at all?

  DOH!

  We've all been there.  I'm glad you have work.

• CAN bus reading NI USB 6259

  I work in can bus monitoring and I have a box NI USB-6259. is it possible to read data with NI USB-6259 CanBus?

  Thank you very much..

• can you analyze and fix my xbox if necessary

  can you analyze and fix my xbox if needed. I don't have it if my internet or what, but some camp of halo. are so slow

  .

  No, your Xbox can't be analyzed. You can have the Internet or router problems.

  But, your question would probably get more responses in the Xbox forums: http://forums.xbox.com/

• CAN-BUS VIEWER

  Hello

  I use a module NI9862 with a CRIO9081 to retrieve data CAN from another device. I have properly the power module and configure the software with all drivers.

  My problem is that when I start the "BUS data viewer" under MAX, there is no data. But when I use PCAN with my camera, PCAN find tha CAN data correctly...

  Is there a special configuration under Max for the spectator BUS?

  (I put correctly rate and pilots the module...)

  Hi Vincent,.

  Have you tried to navigate to the settings > Interfaces and database settings and set the normal operation setting on subordinate if you CAN port is reserved and used by your application VeriStand when you try to monitor traffic?

• myRIO myHub CAN bus

  In the week OR this year, there was a company that made a device called myHub who connected on top of the myRIO and provided several USB ports (I think only 3) and a physical ethernet port.  This same company has also demonstrated a bus CAN add to communicate via the car standard CAN.

  I've done a lot of research, but I couldn't find these products, or the company that makes them.  Is there information from this company about these products and their availability?

  Hello

  I think you're looking for the X [MAY] card listed here developed by a company called Stratom.

  I hope this helps

• NI-CAN Bus Monitor still works, but no examples of LabVIEW

  I have a USB-8473 on a PC running Windows XP I'm trying to monitor transmissions CAN go to an external device. No matter what settings I select in the Measurent Explorer & Automation, the bus monitor never miss a message and is completely error-free. Using the example "CAN receive error Frames.vi" included with NI-CAN 2.6.2 I get almost 100% error for all settings. I use 125000 baud in MAX and in the VI.

  Configuration:

  USB-8473

  NI-CAN 2.6.2

  MAX 4.5.1

  LabVIEW 8.6

  Any Suggestions?

  Thank you

  Jim

  Do you know what your baud rate? You can use the BTR values to program the SJA1000 with the settings real bit rate baud. The current formula should be the online help.

• How can I analyze the flow on SF302 - 08 p

  Hello

  I have a SF302 switch - 08 p and I'm looking for an option to analyze all streams on it. I tried to enable netflow, but it seems that the product does not support because I can't access the stream ip like here: http://www.cisco.com/c/en/us/td/docs/ios-xml/ios/netflow/configuration/12-4t/nf-12-4t-book/cfg-nflow-data-expt.html

  Here is some information on the switch:

  switch08G4 #show version
  SW version 1.3.5.58 (date October 10, 2013 time 17:15:41)
  Start the version 1.0.0.4 (April 8, 2010 time 16:37:57)
  HW version V30
  switch08G4 terminal #configure
  switch08G4 (config) #interface range 1-8 FE
  switch08G4 (config-if-range) #ip
  ARP ARP configuration commands
  configuration DHCP DHCP services
  Guard-defined source enable IP Source Guard on the interface status
  switch08G4 (config-if-range) #ip infiltration flow
  % Unrecognized command

  Thank you for your answer

  Hi Emmanuel, this product does not support anything like Netflow. Your next bet is SNMP and who would probably not do what you want, if you are specifically looking for the Netflow feature sets.

  One thing I have a question, when you say "analyze the flow of all", does that mean that you want to capture all the traffic, you can record and read it again? The closest you can do with is doing a session on the monitor for a VLAN integer and launch wireshark there to capture the data. I'm not sure that's what you want, but if you want to capture all packets and save it somewhere, it's a way to do it, but a bad way to do it.

• The cRIO serial port can be used for the CAN bus communication?

  I would like to order a CVC with a CAN of network device and would like to know if this can be accomplished by using a serial port integrates the cRIO (OR cRIO-9024 in my case). Is it possible, or would need a C Series module CAN?

  You need a C Series module. Series and CAN use a DB9, but they do not have the same physical layer.

• CAN-bus interface on RIO Eval Board

  I am trying to use the interface on the assessment board sbRIO CAN. I installed the driver from RIO 101 shipped package, and the "Embeded CAN for sbRIO" functions are now on the range of functions. However when I place a CAN function on the block diagram, a popup appears, and Labview trying to locate a dll called rioembeddedlvapi.dll without success. It is possible to say "Ignore the point" and he gives up and puts the item on the block diagram.  Anyone know what is happening here, and whether or not it can just be ignored?  Thank you

  I was able to solve the problem on the RIO evaluation board to remove and reinstall the embedded RIO CAN package. Something must have been corrupted.

• Table error ' can not analyze the SQL query!

  Hi all

  I created a view on my database called VIEW_MEMBER_PARTIC_PROJECTS

  If I run a query showing the results of the view:

  SELECT * FROM VIEW_MEMBER_PARTIC_PROJECTS

  I get the following data

  Projects	Participants
  1	31 S
  2	41
  3	19
  4	3
  5	3
  6	1
  7	2

  Now, I wanted to represent this diagram in the APEX so I created a graphic region and entered the Source query generator and the manufacturer produces the following code

  Select null, label projects, value1 Participant link

  of "SCHEMANAME." "" VIEW_MEMBER_PARTIC_PROJECTS ".

  With this code, I get an error:

  Cannot parse the SQL query!

  Select the link null, label projects, value1 "SCHEMANAME Participant." "" VIEW_MEMBER_PARTIC_PROJECTS ".

  Some queries can be run when you run your application, if your query is syntactically correct, you can save your query without validation (see options below the source of the query).

  The code looks OK, but I do not see to save options as the error code is mentioned.

  No one knows how to fix this?

  Thank you

  JaReg wrote:

  I finally found the problem.

  I looked at the code for the view and changed the start of:

  CREATE OR REPLACE FORCE EDITIONABLE VIEW "SCHEMANAME." "" VIEW_MEMBER_PARTIC_PROJECTS "("Participant","Projects")

  AS

  TO

  CREATE OR REPLACE VIEW "SCHEMANAME." "" VIEW_REPEAT_PARATIC ".

  AS

  And that seemed to fix it. I'm not entirely sure why though.

  The view was created using the quoted identifiers for column names. This makes them sensitive and means that they must always be referenced using double quotes. In the absence of quotation marks, Oracle is not case insensitive and automatically converts all uppercase identifiers. The application of graph:

  Select the link null, label projects, value1 "SCHEMANAME Participant." "" VIEW_MEMBER_PARTIC_PROJECTS ".

  has therefore been interpreted by Oracle:

  SELECT THE LINK NULL, LABEL, VALUE1 "SCHEMANAME PARTICIPANT PROJECTS." "" VIEW_MEMBER_PARTIC_PROJECTS ".

  and PROJECTS and PARTICIPANT columns were not recognized because the columns defined for the view have been 'Participant' and 'projects '. The graphic request should have been:

  Select the link null, the label of "Projects", "Participant" value1 "SCHEMANAME." "" VIEW_MEMBER_PARTIC_PROJECTS ".

  As you have now discovered, quoted identifiers are a source of nothing but obscure bugs and should never be used for database objects. He also pointed out the reason why you should always use a standardized, form tiny, coding style as it is faster to type, easy to read and less prone to errors.