Similar Questions

• How can I use internal clock case OR USB - 6259 BNC for the acquisition of digital data in my own big software?

  I want to integrate the ANSI C sample program ReadDigPort - ExtClk.c in my own big package.

  I want to use the internal clock of the BNC NI USB-6259 (.. 80 kHz 120 kHz).

  In the document:
  High speed M: Series Multifunction DAQ for USB - 16-bit, up to 1.25 MECH built-in BNC connectivity. / s,.
  is written:
  Or sample DI source clock: Any PFI, RTSI, HAVE sample or convert clock, AO, Ctr n out internal and many other signals sample clock
  The digital subsystem doesn't have its own dedicated internal synchronization engine. Therefore, a sample clock must be provided another subsystem on the device or from an external source.

  How can I use internal clock case OR USB - 6259 BNC for the acquisition of digital data in my own big software?
  With what other subsystem on the device can generate a source of the clock? How?

  It is possible to set a clock on an internal counter (for example ' Dev1/ctr0"):
  Creates channels to generate digital impulses that define the freq and dutyCycle and adds the channel of the task that you specify with taskHandle.
  DAQmxCreateCOPulseChanFreq (taskHandle, "Dev1/ctr0" units, clockName, idleState,
  initialDelay, freq, the duty cycle); works

  But it is not possible to drive this internal clock to a terminal (for example "/ PFI0/Dev1"):
  DAQmxErrChk (DAQmxCreateCOPulseChanFreq (taskHandle, "/ PFI0/Dev1", clockName, units, idleState, '))
  initialDelay, freq, the duty cycle); does not work: error DAQmx: measurements: type I/O of the physical channel does not match the type of I/O required for the virtual channel you create. Name of the physical channel: PFI0. Name of the virtual channel: clock

  The sample clock source can be derived from an external terminal (for example "/ PFI0/Dev1"):
  Sets the source of the sample clock, the sample clock rate and the number of samples to acquire or generate.
  DAQmxCfgSampClkTiming (taskHandle, "/ PFI0/Dev1", maximumExpectedSamplingRate, DAQmx_Val_Rising, ")
  DAQmx_Val_ContSamps, bufferSize); works. Acquire or generate samples until you stop the task

  But it is not possible to derive the internal counter of the clock (for example ' Dev1/ctr0"):
  DAQmxCfgSampClkTiming (taskHandle, "Dev1/ctr0", maximumExpectedSamplingRate, DAQmx_Val_Rising,
  DAQmx_Val_ContSamps, bufferSize); does not work. Error: Acquire or generate samples until you stop the task: make sure that the name of the terminal is valid for the specified device. See Measurement & Automation explore valid names of terminals. Property: Property of DAQmx_SampClk_Src: DAQmx_SampClk_ActiveEdgeSource device: Terminal Source Dev1: Dev1/ctr0

  Hi datafriend,

  using what it says is correct:

  Or sample DI source clock: Any PFI, RTSI, HAVE sample or convert clock, AO, Ctr n out internal and many other signals sample clock
  The digital subsystem doesn't have its own dedicated internal synchronization engine. Therefore, a sample clock must be provided another subsystem on the device or from an external source.

  This means that if you do not use an external signal as clock you can use the sample clock to HAVE it on board or at the output of the internal counter.

  There are also 2 ANSI C examples in this regard:

  http://zone.NI.com/DevZone/CDA/EPD/p/ID/4485

  http://zone.NI.com/DevZone/CDA/EPD/p/ID/4488

  So in both cases you have to use a fictitious task you need only for the generation of the internal clock (HAVE or CTR)

• How can I use notifications to send data from different sources for the same chart?

  Hello

  I use the model of 'Continuous measurement and logging' project comes with LV 2013.

  It is extremenly helpful in understanding the messaging between the acquisition, graphic and loops of newspaper. (Thank you NEITHER!)

  I ran into a snag though.

  I want to change so that my graphic loop receives notifications of data from two sources of acquisition by the declarant.

  I have trouble getting the data from the two sources to display on one graph.

  I've isolated the problem in the attached vi.

  Here's what happens:

  1. I create 2 parallel loops data and send the data to a third parallel loop with the notifiers.

  2. the third loop receives data from one of the loops because one of the authors of just receiving notifications is to expire instead of receive data.

  Can anyone suggest how can I fix?

  Thank you.

  -Matt

  Here's my modification of your VI. I put notes on the block diagram to explain the changes. He uses a queue for data transfer to avoid data loss. It uses a notifier to stop loops. All local variables and value property nodes have been eliminated.

  The way loops are arrested probably let some data in the queue. No more of one or two iterations of each of the loops of data acquisition. If you need ensure that all data has been displayed (or recorded in a real application), then you must stop acquiring loop first and read the queue until you know it's empty and both other loops stopped. Then stop the render loop and release the queue and the notifier.

  Lynn

• How to use my iPhone as a TV remote control

  Can how I use my iPhone as a TV remote control

  I do not have a generic answer

  You may need to start with your content provider-

  Some like FLAT offer this possibility in their app where you can use the iPhone as a remote control for the part of the satellite TV - do all the normal things a remote

  http://www.tomsguide.com/us/use-iPhone-as-remote, news - 21201.html

• Using Droid Turbo as a TV remote control

  Did someone using their Droid Turbo as a remote control for their TV? If so, what App do you use, and how does it work?

  Thank you

  I do not think that the turbo has an IR blaster, so it does not work like a TV remote in this case.

• Can I attach my Android phone to Sony Internet TV?

  Hello

  I just bought the Sony Internet TV of 32 inches. My internet connection is through my cell provider so I use my wireless phone as a hot spot for my computer. It is extremely fast and works very well. I expect to do the same thing with my internet tv but, unfortunately, the TV does not recognize the signal. Can someone help me solve this problem? I don't want to go back to the tv but will if I can't find a solution.
  Thank you!

  Thank you for your message. Engineering conducted a quick test in our laboratory, with a couple of Mifi hotspots and there is no questions; they worked very well.

• Can I use my iPhone 6 bought in Hong Kong in the Canada?

  Can I use my iPhone 6s bought in Hong Kong in the Canada?

  Your question can mean two things:

  1. Can I use my iPhone to the Canada?  I'll be there for a short period of time and wish to use there, but continue to keep my current (based in Hong Kong) cellular service provider.  I know I'm paying expensive roaming charges for my use of telephone and cellular data.
  2. Can I use my iPhone to the Canada?  I bought it in Hong Kong, but will live in the Canada and wish to use a Canadian cell phone company, once I am there.

  The answer to (1) is certainly!

  The answer to (2) is I'm not sure, but I do not.  To have any hope of answer (2) 'Yes', you at least should:

  • Have the cellular carrier based in Hong Kong to unlock iPhone (I don't think that they do so at all - I know that they would not be if the iPhone has begun on the Japan.)
  • Have the cellular company Canadian base to use methods of transmission and/or frequencies (e.g. GSM) accepts the iPhone from Hong Kong.

• Can I use a Gen 4 and Gen 3 ATV on the same network?

  Can I use a Gen 4 and Gen 3 ATV on the same network?

  Yes.

• can you use a deskjet 970cse in black only mode when the color cartridge dries up

  can you use a deskjet 970cse in black only mode when the color cartridge dries up? Thank you, Jerry

  banhien information is very accurate. I would just add a bit of it. Because this printer uses a tricolor cartridge and a black, it should be one of the printers that will print with just the black cartridge installed. It is called print in backup mode. I should happen automatically when you remove the color cartridge and try printing. A message will arrive on the printer or the computer and ask you if you want to print in backup mode. Say yes, and it should let you print. Hope that helps.

• How to convert an mp3 file to a file rtext? Can I use windows media player to play mp3 and have the recigition speech to convert to text?

  Can I use windows media player to play mp3 and have the recigition speech to convert to text?

  You can get on a conversion of 70% in reading a file in Windows Media Player using something like Dragon Naturally Speaking to convert. If you set the playback speed to slow in Windows Media Player to play > play speed, you will get a better result. The best option is to download the file to an audio transcription service, but which generally costs 0, 50-1, 00 per minute of audio.

• Can I use Draw on my desktop? Is it only the mobile app?

  Can I use Draw on my desktop? Is it only the mobile app?

  Hi EyeArt,

  Draw is a mobile application only.

  Hope that helps.

  Sue.

• can I use photoshop on a pc and a mac with the same license?

  can I use photoshop on a pc and a mac with the same license?

  Yes, just install the application of cc, https://creative.adobe.com/products/creative-cloud on each computer desktop and use it to install your programs cc.

• Hi, I would like to use one of your images on a product for the purpose of illustration, for example, it will be used to show where people can place their own image on a badge. Standard license would allow this?

  Hi, I would like to use one of your images on a product for the purpose of illustration, for example, it will be used to show where people can place their own image on a badge. Standard license would allow this?

  Hello

  Yes. It totally depends on what application you use.

  See pricing and membership creative cloud plans | Adobe Creative Cloud for plans and prices.

  Kind regards

  Sheena

• Hi, I'm on a PC running windows 10. I just started using Lightroom CC and wildfire and feature drop for the sorting of the pictures in collections has stopped working. can someone suggest something please?

  Hi, I'm on a PC running windows 10. I just started using Lightroom CC and wildfire and feature drop for the sorting of the pictures in collections has stopped working. can someone suggest something please?

  Your catalog backup and reset the preferences as mentioned wobertc

  Press the shift and Option on Mac, or the shift and Alt PC (windows) keys. Select Reset preferences

  

  ~ Assani

• During upgrade Adobe Creative Suite CS4 ME in Adobe Creative Suite CS5.5 Design Premium, I get an error saying that the serial number is not an eligible product, please try another. I used to be able to get a code for the customer service, but I can't

  During upgrade Adobe Creative Suite CS4 ME in Adobe Creative Suite CS5.5 Design Premium, I get an error saying that the serial number is not an eligible product, please try another. I used to be able to get a code for the customer service, but I can't chat. Please advise!

  MoeGhazal I have reviewed your account and it seems that you have upgraded to a volume license CS4 Design Premium for an upgrade of retail Design Premium 5.5.

  I also shows that you have made two purchases of CS5.5 Design Premium, but the second purchase was cancelled.  Make sure that you use the serial number that ends in 7886.

  If you are using the correct serial number, then it is likely, that the installer won't recognize your serial number of volume license CS4 as being valid for upgrade.  If you can contact our support team you can be traversed through an unlocking procedure to allow you to proceed with the installation.  You can contact our team of support directly in Contact with the customer.  You can try to install a web browser, you have not previously used.  It of probably a toolbar or other software applications affect your ability to access the media cat successfully.

  If you are unable to reach our support team, then please check your account information is accurate.  If you can please then update this discussion after the confirmation of this so I can ask a member of our support team contact you directly.

  I would recommend again reaching out directly if possible it will be the most effective method to resolve your current error.