Can TV 32DL933B - I connect the SKY via RF?

Similar Questions

• Satellite A60 - impossible to connect the camera via firewire (IEEE)

  Hello

  Have problems with the dv camera connection to
  laptop computer via cardbus IEEE (firewire)
  It seems to be connected, but none noticed and not take at all.

  I think the problem is with the drivers - but what exactly should I install?

  Thank you

  I don't know which cam you use but when the cam is connected and recognized correctly, it will be listed in the Device Manager. So, do you need some software to have access to the material recorded. By using this software you can record the film on the computers HARD drive.

  Later, you can create DVD or do something else. I have more old digital camcorder tape 8 of 8mm inside. I connect the cam with firewire cable too. When the cam is activated, it is recognized and I can copy films of the tape to the computer s portable HARD drive. For this I use Ulead Movie Maker software.

  What exactly do you do with your cam?

• Connect the printer via the home router

  I have LaserJet CP1525, who has a wireless option... recently I moved my router on the different floor and can not connect to my my wireless home network option trough ethernet cable/router...tried on the printer, but "failed to connect".

  any ideas? Thank you

  Hi BoleczekNieduzy,

  Welcome to the HP Forums.

  I see that you have any questions, set up the printer on the network cable and even the wireless network.
  I will do my best to help you with this problem.

  Cycle power to the router.

  First, we must restore the defaults on the printer.

  Press the OK button on the printer, go to the service, and then select restore default settings.

  Print a printer configuration page to make sure that the IP address and SSID are erased.

  Print a Configuration report.

  Select the method.

  Uninstall the printer software.
  Insert the software CD into the CD drive.
  Follow the on-screen instructions.

  When you are prompted, select the connection through the wireless network.

  If you're still having problems, restore the default values and follow this method:

  Connect the printer to the router with an Ethernet cable.
  Wait about 1 minute and the printer must have a valid IP address.
  Print the configuration page to get the IP address of the printer.
  Type the IP address in the address bar of Internet Explorer which should open the printer's built-in web services page.
  Installing wireless over here now.
  Click the networking, wireless on the left, fill in information about the network and apply the settings.
  After the confirmation, then disconnect the Ethernet cable.
  Now you should have a flashing light on the printer in 1 minute wireless about.

  Run the installation again.

  I have provided a document to configure the wireless connection, or you can follow my different methods provided.

  Installation of the software of the printer on a wireless network or network (Ethernet) cable.

  If the Wireless does not always connect, to view these settings on the router.

  You have a double router broadband?
  If it is set to 5 GHZ network, you may need to change to 2.4 GHZ. (rename the 5 GHz or turn it off)
  The WPA key setting must be on AES to work properly not TKIP.
  If it is set to the 64-bit encryption, then change it to 128-bit.
  Multi flow must be enabled.
  Router firewall must be open for printer ports.
  If you have Mac filtering give you printer hardware to meet the needs of the configuration page.

  Please let me know if this is not the problem.

  Have a great day.
  Thank you.

• Unable to connect the client via vsphere ESX host

  Dear team,

  Once I tried to connect to client host via vsphere ESX I m getting following error.

  

  VCenter version: 4.1.0 345043

  vSphere client: 4.1.0 345043

  ESX Version: 4.1.0 721871

  You help me on the same request.

  concerning

  Mr. VMware

  It is usually advisable, but not an obligation, to have the build of your version of vCenter client correspondence.

  You can see the Interopabilty matrix for supported configurations

  http://PartnerWeb.VMware.com/comp_guide2/SIM/interop_matrix.php

• Connect the scanner via TimeCapsule

  I have a Canon LiDE 120 Cancan scanner.  I want to connect to my local network using port USB TimeMachine.  My laser printer works this way, but the utility OS 'Printers and Scanners' preferences won't find the scanner.

  Is it possible a scanner by the TC/airport network for all my computers can "see"?  If so would appreciate any advice on the installation program.

  Note: even if directly connected to a computer the button 'share (printer) on the network' disappears when a scanner is selected.

  Thank you

  Not with a USB scanner. The time Capsule does not support that.

  (144525)

• How can I enable 'analysis of the computer' via the printer software?

  I just purchased a HP Deskjet Ink Advantage 3525, everything works, but when I want to scan something it tells me to activate "computer scan" through the software of the printer. I was wondering how you do it...

  I have a mac os x lion (10.7.5)

  I would be very happy if someone could respond as soon as possible because I need the scanner to make a portfolio of University.

  Hey yunkiflower,

  Please take a look through the information in the document below.

  How to perform a scan: OS X v10.7

  It will give you the information to learn how to perform scans with your printer and the combination of the OS.  I hope this helps.

• Qosmio G30: Can I use component video software plug-in to connect the Gamecube or PS2?

  The Qosmio G30 has a VIDEO-IN bit for the red/white/yellow wires... So I wondered if this meant that I could connect my PS2/Gamecube/similar to television, playing games on my laptop, save me money when I move to College :)

  Indeed, if I pretend that I'll put up a set - top box for the TELEVISION, the Gamecube appears under "Video Composite", I just can't save like a channel or anything at this point...

  Someone help? Would be very grateful...
  Thankee.

  Hello
  The s-video-in port can be used to connect and to import data from the external device such as an analog video camera or VCR. Imported video can be edited or written on a DVD disc.
  Video port can be used to connect the external device such as a game console

  I think you should also consult the user manual because you will find the full description on unique ports and use.

• Satellite L650-11F - how to connect to LCD via an HDMI cable?

  Hello world

  I have the Satellite L650-11F with ATI 5650 and HDMI port and I want to connect the laptop via HDMI lcd screen so that I have some office using 2 * ATI Catalyst * and * software HydraVision, but ATI sites said that Toshiba notebook is not supported (Please check with your mobile phone OEM for support of the drivers for these laptops).

  So, how can I connect my laptop to LCD screen to get 2 workstation?

  Sorry for my bad English :)

  Hi thebluewriter,

  I think you need to check only the other discussions of the forum on the connection for laptop LCD screen. You will find enough about it!

  In any case, most recent display driver you can download on the official website of Toshiba, but usually it s preinstalled on your laptop.
  If you are using a HDMI cable, use just FN + F5 key combination to switch between monitors. All that s! :)

• Connecting two routers via a static route

  I have a relatively simple configuration involving a Wireless-N Router and a wireless-B router (several years).  The N wireless router is connected to the internet (via DSL modem) and accepts several DHCP clients without problem.  Wireless - b router is connected to the Wireless-N router.  To do this, I connected the WAN port on the router wireless - b to a port on the router Wireless N ethernet (did not use the uplink). I have a PC connected to the router wireless - b, so I want him to be able to hit the internet, but also be accessible to DHCP clients on the Wireless N router.  The PC connects to the internet successfully, but it does not find clients on the network supported by the Wireless-N router.  It's about my setup:

  B 192.168.55.1 wireless router (LAN) 192.168.56.102 (WAN)

  PC 192.168.55.10 (active dhcp)

  Wireless N 192.168.56.1 (LAN) x.x.x.x (internet)

  (several clients dhcp... 192.168.56.100...)

  I've added a static route in the hope that a computer on the network of the Wireless N router would be able to hit the PC, but nothing helped. I've added a static route as such, on the Wireless-N router, which was the only way that that would enable the web interface:

  Destination LAN 192.168.55.0

  Subnet mask 255.255.255.0

  Gateway 192.168.56.102

  I tried to place the router without wireless - B gateway mode, then router and changed mode, then return.  I can connect to the web interface of the router wireless - b from the PC, and I can connect to the internet from the PC.  Also, the PC is able to reach customers on Wireless N, but the reverse is not true, i.e. clients on Wireless N can't find clients on the wireless - B network. Also, I turned on the port forwarding on the router wireless - B so that it points to the PC, in the hope he would lead all traffic to the PC, but still cannot access PC.  How to configure both routers (or both set up as access point?) so that clients on the Wireless N Router can talk to customers on the wireless router - B?  For now, all customers are on DHCP, but finally, I would like to create static entries for at least two or three of them.

  Thanks in advance

  Are Linksys routers teas? If so what model is router B? It may not supported for a DHCP client port forwarding. Even if you can get the port forwarding to work for a client on router B, it will not work for several clients.

  In addition, if you have the option in router B, disable the SPI Firewall. It is the cause of the problem, in my opinion. If you do this, you should port forward.

  Is there a reason that you connect the routers via the WAN port on the router B? You could uplink using an ethernet port on the B to an ethernet port on the N and avoid all this... You can always configure router B as a point of wireless access for specific customers.

• Connect the airport time capsule to telstra NBN

  Grateful for the help with the required parameters to set up my time capsule airport with Telstra NBN via Telstra condition max modem router gateway, I want to use the TC as my router and for backups, I understand that I need to be able to use the TC as a router and connect the TC via an ethernet cable to the gateway I need to put the door in Bridge mode, thanks in advance

  Double post.

• Satellite P100-160 - how to connect the camcorder?

  Hi all!

  Can anyone can advise, try to connect the Sony camcorder with 4 pin i.link, but can't seem to connect the two devices.

  I have AC power on the camera, tried to use the other movie maker, adobe, etc. no joy.
  is thinking why is this?
  Thank you

  Hello!

  As Garrett Satellite P100 supports the firewire port.

  Normally, the port is always on and you need an application that does not recognize your camcorder correctly. You can then copy the videos on your laptop.

  Good bye

• Can I watch the sky go app on my TV by connecting my I pad2 using the AV adapter digital Apple 30-pin

  Can I watch the sky go app on my ipad 2 via my hd tv by connecting iPad to my tv via digital of 30 pins of Apple

  AV adapter?

  Apple says you can show what on your screen. (?)

  http://www.Apple.com/shop/product/MD098AM/A/Apple-Digital-AV-adapter

  did you read the comments?

• My iPhone can connect to the computer via Wifi instead of cable? Because I figured that my head of the telephone cable i have problem if the computer cannot detect my folder after plugging in the cable.

  My iPhone can connect to the computer via Wifi instead of cable? Because I figured that my head of the telephone cable i have problem if the computer cannot detect my folder after plugging in the cable.

  Sync your iPhone, iPad or iPod touch with iTunes using a WiFi - Apple...

• My Macbook 2012 mid pro with thunderbolt is connected to the tv via a Macally MDHDMI adapter.  Visuals are delivered as planned but no audio.  Can anyone suggest why no noise please?  And maybe a fix?  See you soon...

  My Macbook 2012 mid pro with thunderbolt is connected to the tv via a Macally MDHDMI adapter.  Visuals are delivered as planned but no audio.
  Can anyone suggest why no noise please?  And maybe a fix?
  See you soon...

  Have you checked system-> Sound-> output preferences to see if you can select the HDMI output?

• You will need to plug Sony IEEE 1394 camcorder to an iMac. It would connect to the thunderbolt via an adapter port? I have a cable of firewire 800 and wanting to know how to get the video of my iMac. Thanks for any help you can give :)

  I borrowed a camcorder tape Sony that has an IEEE 1394 (ilink Sony) and eager to download video from my iMac.

  It would connect to the thunderbolt via an adapter port?

  I have a cable of firewire 800 and wanting to know how to get the video from my iMac via this cable.

  Appreciate any help you can give :)

  You want a Thunderbolt Apple FireWire adapter. Here is a link (to the US store):

  http://www.Apple.com/shop/product/MD464LL/A/Apple-Thunderbolt-to-FireWire-ADAPTE r? FNODE = 8 b & fs = f % 3Dadapter % 26fh %3 D 4595% 252B45b0

  Sorry, I don't know what software you need to play your video, once you get the cable work.