Cannot access at the beginning of the BIOS to the top
Hello
My son has a laptop Lenovo G580. Since last night to the commissioning the keyboard does not work. I can't access BIOS setup F2 or F12 on this machine to check the setting. I can not even access F8 to run mode without failure. The laptop has windows 8 OS. I ran the Lenovo Solution Center and I got some errors:
- Checkup: Manager bus devices (support of virtual storage) StorLIb with disabilities.
- Analysis of equipment has detected one or more failures. Result code: WHD01V01G-Bj8C9E
If I use an external keyboard, I can only access some windows functions.
I don't know if the problem is the keyboard, HARD drive, the operating system has been corrupted.
The application software only I can open without problem is Google Chrome. Yet I can not type anything using the laptop keyboard or external keyboard.
Help, please.
Thank you.
Shervin
Hello
You should check with Lenovo's Support or a real computer store (the one that made his own in shop
service on Lenovo laptops).
Support from Lenovo and downloads
http://www-307.IBM.com/PC/support/site.WSS/homeLenovo.do
Lenovo forums
http://forums.Lenovo.com/ I hope this helps.
Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle="" -="" mark="" twain="" said="" it="">->
Tags: Windows
Similar Questions
-
Cannot open email in Hotmail via Firefox. I have Vista installed on the pc and Windows 7 on the laptop, but cannot access all the features of Hotmail. I tried to clear the cache and restart Firefox, but I still cannot use Hotmail.
Not this problem when I go to Internet Explorer.
Hello, it was noted that the foxit pdf plugin is causing this issue. You can disable this plugin in firefox > addons > plugin until what foxit offers a patch/update for the plugin.
-
Windows cannot access and the bios options are not displayed in the bios options
Windows cannot access the bios options are not displayed in the bios options, I don't know what the problem is. I've used the laptop and turned on and when I start windows again, there is a usb modem in the usb port (it contains the setup of windows, ubuntu, mac files). That's all that's happened with me, and I get the error in the photos. I have windows 8 x 64 and fujitsu lh532 core i5
Hello
Thanks for posting your query in Microsoft Community.
- Why are you trying to access BIOS?
In case you have problems with Windows 8, you can come back with more information, and we will be happy to answer your query.
To access BIOS, we recommend that you contact your computer manufacturer help you make changes in the BIOS.
Warning: Change BIOS / semiconductor (CMOS) to complementary metal oxide settings can cause serious problems that may prevent your computer from starting properly. Microsoft cannot guarantee that problems resulting from the configuration of the BIOS/CMOS settings can be solved. Changes to settings are at your own risk.
Hope this information is useful. Please feel free to answer in the case where you are facing in the future other problems with Windows.
-
ASA 5505 VPN established, cannot access inside the network
Hi, I recently got an ASA 5505, and I spent weeks to find a way to set up a VPN on it.
After a few days, I finally found the solution to connect to my ASA with a VPN client yet and cannot access devices that are connected to the ASA.
Here is my config:
ASA Version 8.2 (5)
!
hostname asa01
domain kevinasa01.net
activate 8Ry2YjIyt7RRXU24 encrypted password
2KFQnbNIdI.2KYOU encrypted passwd
names of
!
interface Ethernet0/0
switchport access vlan 2
!
interface Ethernet0/1
!
interface Ethernet0/2
!
interface Ethernet0/3
switchport access vlan 5
!
interface Ethernet0/4
!
interface Ethernet0/5
!
interface Ethernet0/6
!
interface Ethernet0/7
!
interface Vlan1
nameif inside
security-level 100
IP 192.168.1.1 255.255.255.0
!
interface Vlan2
nameif outside
security-level 0
IP address dhcp setroute
!
interface Vlan5
No nameif
security-level 50
IP 172.16.1.1 255.255.255.0
!
passive FTP mode
DNS server-group DefaultDNS
domain kevinasa01.net
permit same-security-traffic intra-interface
Remote_Kevin_splitTunnelAcl list standard access allowed 192.168.1.0 255.255.255.0
inside_nat0_outbound to access ip 192.168.1.0 scope list allow 255.255.255.0 192.168.254.0 255.255.255.240
inside_nat0_outbound list of allowed ip extended access all 192.168.254.0 255.255.255.0
inside_nat0_outbound list of allowed ip extended access entire 192.168.1.0 255.255.255.0
sheep - in extended Access-list allow IP 192.168.254.0 255.255.255.0 192.168.1.0 255.255.255.0
access extensive list ip 192.168.254.0 outside_access_in allow 255.255.255.0 any
access extensive list ip 192.168.254.0 inside_access_in allow 255.255.255.0 any
pager lines 24
asdm of logging of information
Outside 1500 MTU
Within 1500 MTU
pool pool 192.168.254.1 - 192.168.254.10 255.255.255.0 IP mask
ICMP unreachable rate-limit 1 burst-size 1
don't allow no asdm history
ARP timeout 14400
Global 1 interface (outside)
NAT (outside) 1 192.168.254.0 255.255.255.0
NAT (inside) 0 access-list sheep - in
NAT (inside) 1 192.168.1.0 255.255.255.0
NAT (inside) 1 0.0.0.0 0.0.0.0
Access-group outside_access_in in interface outside
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
Floating conn timeout 0:00:00
dynamic-access-policy-registration DfltAccessPolicy
Enable http server
http 192.168.1.0 255.255.255.0 inside
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown cold start
Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac
Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac
Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac
Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac
Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac
Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac
life crypto ipsec security association seconds 28800
Crypto ipsec kilobytes of life - safety 4608000 association
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs Group1 set
Crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 value transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5
outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
outside_map interface card crypto outside
crypto ISAKMP allow outside
crypto ISAKMP policy 10
preshared authentication
3des encryption
sha hash
Group 2
life 86400
Telnet timeout 5
SSH timeout 5
Console timeout 0
management-access inside
dhcpd outside auto_config
!
dhcpd address 192.168.1.5 - 192.168.1.36 inside
dhcpd allow inside
!a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
WebVPN
internal Remote_Kevin group strategy
attributes of Group Policy Remote_Kevin
value of server DNS 192.168.1.12 192.168.1.13
VPN - connections 3
Protocol-tunnel-VPN IPSec
Split-tunnel-policy tunnelspecified
value of Split-tunnel-network-list Remote_Kevin_splitTunnelAcl
kevinasa01.NET value by default-field
username kevin mz6JxJib/sQqvsw9 password encrypted privilege 0
username kevin attributes
VPN-group-policy Remote_Kevin
type tunnel-group Remote_Kevin remote access
attributes global-tunnel-group Remote_Kevin
address-pool
Group Policy - by default-Remote_Kevin
IPSec-attributes tunnel-group Remote_Kevin
pre-shared key *.
!
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns preset_dns_map
parameters
maximum message length automatic of customer
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the preset_dns_map dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
inspect the rsh
inspect the rtsp
inspect esmtp
inspect sqlnet
inspect the skinny
inspect sunrpc
inspect xdmcp
inspect the sip
inspect the netbios
inspect the tftp
Review the ip options
inspect the icmp
inspect the icmp error
!
global service-policy global_policy
context of prompt hostname
no remote anonymous reporting call
Cryptochecksum:2bb1da52d1993eb9b13c2f6dc97c16cd
: endThank you
Hello
I read your message quickly through my cell phone. I don't know why you have spent your config twice. Maybe a typo issue.
I see the acl sheep in the wrong way. I mean 192.168.254 are your pool VPN and 192.168.1.0 your local LAN.
The acl must be:
sheep - in extended access-list permit ip 192.168.1.0 255.255.255.0 192.168.254.0 255.255.255.0
For nat (inside), you have 2 lines:
NAT (inside) 1 192.168.1.0 255.255.255.0 ==> it is redundant as the 1 below does the same thing with more networks if there is inside side. You can delete it.
NAT (inside) 1 0.0.0.0 0.0.0.0Why are you doing this nat (outside)?
NAT (outside) 1 192.168.254.0 255.255.255.0
Here are the first questions that I have seen by reading through my mobile. Let's change this and let me know. I'll take a look later with a computer (tonight or tomorrow)
Thank you.
PS: Please do not forget to rate and score as good response if this solves your problem.
-
I have problems to access the resources within the network when connecting with the Cisco VPN client for a version of 8.4 (3) operation of the IOS Cisco ASA 5510. I tried all new NAT 8.4 orders but cannot access the network interior. I can see traffic in newspapers when ping. I can only assume I have NAT evil or it's because the inside interface of the ASA is on the 24th of the same subnet as the network interior? Please see config below, any suggestion would be appreciated. I configured a VPN site to another in this same 5510 and it works well
Thank you
interface Ethernet0/0
Speed 100
full duplex
nameif outside
security-level 0
IP x.x.x.x 255.255.255.240
!
interface Ethernet0/1
Speed 100
full duplex
nameif inside
security-level 100
IP 10.88.10.254 255.255.255.0
!
interface Management0/0
Shutdown
nameif management
security-level 0
no ip address
!
permit same-security-traffic inter-interface
permit same-security-traffic intra-interface
network of the PAT_to_Outside_ClassA object
10.88.0.0 subnet 255.255.0.0
network of the PAT_to_Outside_ClassB object
subnet 172.16.0.0 255.240.0.0
network of the PAT_to_Outside_ClassC object
Subnet 192.168.0.0 255.255.240.0
network of the LocalNetwork object
10.88.0.0 subnet 255.255.0.0
network of the RemoteNetwork1 object
Subnet 192.168.0.0 255.255.0.0
network of the RemoteNetwork2 object
172.16.10.0 subnet 255.255.255.0
network of the RemoteNetwork3 object
10.86.0.0 subnet 255.255.0.0
network of the RemoteNetwork4 object
10.250.1.0 subnet 255.255.255.0
network of the NatExempt object
10.88.10.0 subnet 255.255.255.0
the Site_to_SiteVPN1 object-group network
object-network 192.168.4.0 255.255.254.0
object-network 172.16.10.0 255.255.255.0
object-network 10.0.0.0 255.0.0.0
outside_access_in deny ip extended access list a whole
inside_access_in of access allowed any ip an extended list
11 extended access-list allow ip 10.250.1.0 255.255.255.0 any
outside_1_cryptomap to access extended list ip 10.88.0.0 255.255.0.0 allow object-group Site_to_SiteVPN1
mask 10.250.1.1 - 10.250.1.254 255.255.255.0 IP local pool Admin_Pool
NAT static NatExempt NatExempt of the source (indoor, outdoor)
NAT (inside, outside) static source any any static destination RemoteNetwork4 RemoteNetwork4-route search
NAT static LocalNetwork LocalNetwork destination (indoor, outdoor) static source RemoteNetwork1 RemoteNetwork1
NAT static LocalNetwork LocalNetwork destination (indoor, outdoor) static source RemoteNetwork2 RemoteNetwork2
NAT static LocalNetwork LocalNetwork destination (indoor, outdoor) static source RemoteNetwork3 RemoteNetwork3
NAT (inside, outside) static source LocalNetwork LocalNetwork static destination RemoteNetwork4 RemoteNetwork4-route search
!
network of the PAT_to_Outside_ClassA object
NAT dynamic interface (indoor, outdoor)
network of the PAT_to_Outside_ClassB object
NAT dynamic interface (indoor, outdoor)
network of the PAT_to_Outside_ClassC object
NAT dynamic interface (indoor, outdoor)
Access-group outside_access_in in interface outside
inside_access_in access to the interface inside group
Route outside 0.0.0.0 0.0.0.0 x.x.x.x 1
dynamic-access-policy-registration DfltAccessPolicy
Sysopt connection timewait
Service resetoutside
Crypto ipsec transform-set ikev1 ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-esp - aes esp-md5-hmac
Crypto ipsec transform-set esp-ikev1 esp-md5-hmac bh-series
Crypto ipsec transform-set ikev1 esp ESP-DES-MD5-esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-3DES-MD5-esp-3des esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-DES-SHA esp - esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-128-SHA aes - esp esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
Crypto ipsec transform-set ikev1 SHA-ESP-3DES esp-3des esp-sha-hmac
Crypto-map dynamic dynmap 10 set pfs
Crypto-map dynamic dynmap 10 set transform-set bh - set ikev1
life together - the association of security crypto dynamic-map dynmap 10 28800 seconds
Crypto-map dynamic dynmap 10 kilobytes of life together - the association of safety 4608000
Crypto-map dynamic dynmap 10 the value reverse-road
card crypto mymap 1 match address outside_1_cryptomap
card crypto mymap 1 set counterpart x.x.x.x
card crypto mymap 1 set transform-set ESP-AES-256-SHA ikev1
card crypto mymap 86400 seconds, 1 lifetime of security association set
map mymap 1 set security-association life crypto kilobytes 4608000
map mymap 100-isakmp ipsec crypto dynamic dynmap
mymap outside crypto map interface
crypto isakmp identity address
Crypto isakmp nat-traversal 30
Crypto ikev1 allow outside
IKEv1 crypto ipsec-over-tcp port 10000
IKEv1 crypto policy 5
preshared authentication
3des encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 10
preshared authentication
3des encryption
sha hash
Group 1
life 86400
IKEv1 crypto policy 50
preshared authentication
the Encryption
md5 hash
Group 2
life 86400
IKEv1 crypto policy 60
preshared authentication
aes-256 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 70
preshared authentication
aes-256 encryption
sha hash
Group 1
life 86400
IKEv1 crypto policy 90
preshared authentication
aes encryption
sha hash
Group 2
life 86400
Telnet timeout 5
Console timeout 0
management-access inside
a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
WebVPN
internal BACKDOORVPN group policy
BACKDOORVPN group policy attributes
value of VPN-filter 11
Ikev1 VPN-tunnel-Protocol
Split-tunnel-policy tunnelall
BH.UK value by default-field
type tunnel-group BACKDOORVPN remote access
attributes global-tunnel-group BACKDOORVPN
address pool Admin_Pool
Group Policy - by default-BACKDOORVPN
IPSec-attributes tunnel-group BACKDOORVPN
IKEv1 pre-shared-key *.
tunnel-group x.x.x.x type ipsec-l2l
tunnel-group ipsec-attributes x.x.x.x
IKEv1 pre-shared-key *.
!
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns preset_dns_map
parameters
maximum message length automatic of customer
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the preset_dns_map dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
inspect the rsh
inspect the rtsp
inspect esmtp
inspect sqlnet
inspect the skinny
inspect sunrpc
inspect xdmcp
inspect the sip
inspect the netbios
inspect the tftp
Review the ip options
!
global service-policy global_policy
Excellent.
Evaluate the useful ticket.
Thank you
Rizwan James
-
ASA 5505 VPN cannot access inside the host
I have access remote VPN configuration on an ASA 5505, but cannot access the host or the AAS when I connect through the VPN. I can connect with the Cisco VPN client and the VPN is on on the SAA and it shows that I am connected. I have the correct Ip address, but I can't ping or you connect to one of the internal addresses. I can't find what I'm missing. I have the VPN without going through the ACL interface. Because I can connect but not going anywhere I'm sure I missed something.
framework for configuration below
interface Vlan1
nameif inside
security-level 100
10.1.1.1 IP address 255.255.255.0
IP local pool xxxx 10.1.1.50 - 10.1.1.55 mask 255.255.255.0
Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
Crypto-map dynamic outside_dyn_map 20 set pfs
Crypto-map dynamic outside_dyn_map 20 the value transform-set ESP-3DES-SHA
PFS set 40 crypto dynamic-map outside_dyn_map
Crypto-map dynamic outside_dyn_map 40 value transform-set ESP-3DES-SHA
Crypto-map dynamic inside_dyn_map 20 set pfs
Crypto-map dynamic inside_dyn_map 20 the value transform-set ESP-3DES-SHA
map outside_map 65535-isakmp ipsec crypto dynamic outside_dyn_map
outside_map interface card crypto outside
map inside_map 65535-isakmp ipsec crypto dynamic inside_dyn_map
inside crypto map inside_map interface
crypto ISAKMP allow inside
crypto ISAKMP allow outside
crypto ISAKMP policy 10
preshared authentication
3des encryption
sha hash
Group 2
life 86400
global service-policy global_policy
XXXXXXX strategy of Group internal
attributes of the strategy group xxxxxxx
banner value xxxxx Site Recovery
WINS server no
24.xxx.xxx.xx value of DNS server
VPN-access-hour no
VPN - connections 3
VPN-idle-timeout 30
VPN-session-timeout no
VPN-filter no
Protocol-tunnel-VPN IPSec
Split-tunnel-policy tunnelall
by default no
disable secure authentication unit
disable authentication of the user
user-authentication-idle-timeout no
disable the IP-phone-bypass
disable the leap-bypass
disable the NEM
disable the NAC
NAC-sq-period 300
NAC-reval-period 36000
NAC-by default-acl no
the address value xxxxxx pools
enable Smartcard-Removal-disconnect
the firewall client no
WebVPN
url-entry functions
Free VPN of CNA no
No vpn-addr-assign aaa
No dhcp vpn-addr-assign
tunnel-group xxxx type ipsec-ra
tunnel-group xxxx general attributes
xxxx address pool
Group Policy - by default-xxxx
blountdr group of tunnel ipsec-attributes
pre-shared-key *.
Missing nat exemption for vpn clients. Add the following and you should be good to go.
inside_nat0_outbound list of allowed ip extended access any 192.168.10.0 255.255.255.0
NAT (inside) 0-list of access inside_nat0_outbound
-
PIX501 customer VPN - cannot access inside the network with VPN Session
What follows is based on the config on the attached link:
PIX Ver 6.2 (3) - VPN Client 3.3.6(A) - Windows XP Client PC
We can establish the VPN to the PIX501 session, but we cannot access the network private behind the pix.
Here is the config - I can't determine why it does not work, we are desperate to get there as soon as POSSIBLE!
We have the same problem with the customer 4.0.3(c)
Thanks in advance for any help!
=======================================
AKCPIX00 # sh run
: Saved
:
6.2 (3) version PIX
ethernet0 nameif outside security0
nameif ethernet1 inside the security100
hostname AKCPIX00
domain.com domain name
fixup protocol ftp 21
fixup protocol http 80
fixup protocol h323 h225 1720
fixup protocol h323 ras 1718-1719
fixup protocol they 389
fixup protocol rsh 514
fixup protocol rtsp 554
fixup protocol smtp 25
fixup protocol sqlnet 1521
fixup protocol sip 5060
fixup protocol 2000 skinny
fixup protocol sip udp 5060
names of
access-list 101 permit ip 192.168.1.0 255.255.255.0 10.0.0.0 255.255.255.0
pager lines 24
interface ethernet0 10baset
interface ethernet1 10full
Outside 1500 MTU
Within 1500 MTU
external IP address #. #. #. # 255.255.240.0
IP address inside 192.168.1.5 255.255.255.0
alarm action IP verification of information
alarm action attack IP audit
IP local pool akcpool 10.0.0.1 - 10.0.0.10
history of PDM activate
ARP timeout 14400
Global 1 interface (outside)
(Inside) NAT 0-list of access 101
NAT (inside) 1 0.0.0.0 0.0.0.0 0 0
Route outside 0.0.0.0 0.0.0.0 #. #. #. # 1
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0: 10:00 udp 0:02:00 CPP 0: h323 from 10:00 0:05:00 sip 0:30:00 sip_media 0:02:00
Timeout, uauth 0:05:00 absolute
GANYMEDE + Protocol Ganymede + AAA-server
RADIUS Protocol RADIUS AAA server
AAA-server local LOCAL Protocol
the ssh LOCAL console AAA authentication
No snmp server location
No snmp Server contact
SNMP-Server Community public
No trap to activate snmp Server
enable floodguard
Permitted connection ipsec sysopt
No sysopt route dnat
Crypto ipsec transform-set esp - esp-md5-hmac RIGHT
Crypto-map dynamic dynmap 10 transform-set RIGHT
map mymap 10-isakmp ipsec crypto dynamic dynmap
mymap outside crypto map interface
ISAKMP allows outside
part of pre authentication ISAKMP policy 10
encryption of ISAKMP policy 10
ISAKMP policy 10 md5 hash
10 2 ISAKMP policy group
ISAKMP life duration strategy 10 86400
vpngroup address akcpool pool akcgroup
vpngroup dns 192.168.1.10 Server akcgroup
vpngroup akcgroup by default-domain domain.com
vpngroup split tunnel 101 akcgroup
vpngroup idle 1800 akcgroup-time
vpngroup password akcgroup *.
vpngroup idle 1800 akc-time
Telnet timeout 5
SSH #. #. #. # 255.255.255.255 outside
SSH timeout 15
dhcpd address 192.168.1.100 - 192.168.1.130 inside
dhcpd dns 192.168.1.10
dhcpd lease 3600
dhcpd ping_timeout 750
dhcpd allow inside
Terminal width 80
Cryptochecksum:XXXXX
: end
AKCPIX00 #.
Config looks good - just as domestic mine to my local network. The only thing I can think is that you may have entered commands in the wrong order - which means, you could have isakmp or encryption before the config map was complete. Write memory, then reloading the pix is a way to reset everything. If you do not want downtime:
mymap outside crypto map interface
ISAKMP allows outside
Enter these two commands should be enough to reset the ipsec and isakmp.
-
Cannot access on the desktop, the laptop readers.
I have two computers running Win 7 Ultimate. 1 desktop and 1 laptop. I'm running through a Netgear wireless router. Office is hard wired to the router via an ethernet connection. The laptop has a wireless connection. I also have a cable for color laser printer to the router via an ethernet connection.
The laptop can see the desktop and can access the printer and some of the hard disks on the desktop. The laptop can detect and access G: and H: drives on the desktop but not C: D: E: and Z: drives. G: and H: drives are located on an external USB disk door. The other drives are connected internally to the desktop. Trying to access drives unaccessable to the desktop, I get the following error message.
"Windows cannot access \\DESKTOP\Desktop C:. You are not allowed to access \\DESKTOP\Desktop c. contact your network administrator to request access. »
The office displays the icon of the laptop in the network, but I get the same error message when I try to access the laptop, but the laptop is overridden to desktop in the above error message. The error code is: 0 x 80070035.
All readers have enabled file sharing and permissions set for everyone. In fact each player is set up exactly the same thing, and both computers are set up exactly the same except for the name of the computer (eg. Mobile - Office).
Does anyone have any suggestions?
Thanks for any help.
Ed Wood
Hello Edawood,
I suggest check to ensure that all services of collective housing began and then retry the connection:Open the services menu by clicking Start and then type "services.msc" then on enter.
Locate the following services in the list:
· DNS client
· Function Discovery Provider Host
· Function Discovery Resource Publication
· Peer networking grouping
· HomeGroup provider
· HomeGroup listener
· SSDP Discovery
· UPnP device host
Sure they were launched and retry the connection.
To start the service, double click on it and press the 'start' button in the dialog box that appears.
-
cannot access shares the local computer
Hi-
Win7 64 bit. I use homegroup, and I have this Win7PC on my local network with XP and Vista PC. I can see the 2 other PCs on the Win7 PC and get to their shared folders. None of them access to the part of it. I have the name of workgroup defined correctly on all (including this PC Win7).
In addition, oddly enough, on the WIn7 PC, in WIndows Explorer, I can navigate to C:\Users\Public BUT if I try to go into WIndows Explorer, then fall below computer - C: to the network and open it, I see the other 2 PC and the local PC. The WIn7 PC is called "kirk". So, in network - Kirk, IF I open it I see 'users' share. BUT if I click on it, I get the error:
\\kirk\users is not accessible. You might not have permission to use this network resource.
I am logged in as administrator (on Kirk).
So, to rephrase, I am connected to a Win7 PC as an administrator. I can navigate to C:\Users\Public in WIndows Explorer.
BUT if I go to "Network Neighborhood" in WIndows Explorer (it's actually just "network") I see the local PC named Kirk. If I click on it, I see 'User' (share). I can't go to see 'public '.
To make things more awkward, I could access it until a few days ago and I has not installed anything new, although WIn7 can be updated automatically.
Help!
Thank you
Kelly
Hi-
Thanks for the list of things. There was a lot of good links in there. I went through everything without the blinkers "it worked before" and "I won't change anything" on each link there is, I've lived and all checked. The only one I had to do something opened ports in my firewall mcafee.
Nothing helps.
This PC is named kirk and I still don't see files shared this PC itself in windows Explorer - network\kirk. for me, very odd, I am connected to kirk as an administrator. I open Explorer windows on kirk. I can see c:\users\public in windows Explorer, but I do not see network\\kirk\users
so, I thought, let's start over.
I went to the center of network share and changed "active network" of the type "work network" type "home network" and it is now.
working group name has not changed so it's always "the Star", so I can see all the other no WIn7 PC and PC WIn7 himself can see that it is me in network neighborhood.
I'll reboot and be sure to x 2. very weird.
Thanks for your help!
Kelly
-
My MSN Premium or constantly stop itself or takes forever to finally adjust to I can use it. I tried to go to the Microsoft Fix It, with the help of MSN Premium and I get a message saying that it cannot connect with the program that I use. I have Windows 7. If I connect to my Hotmail account, I have no problem there, but MSN Premium is something that I pay for, want to use it, but doesn't seem to work as well.
Hi Nancy,.
Because the problem is with MSN premium I suggest you to contact MSN support for help.
https://support.MSN.com/default.aspx?scrx=1
I hope that helps!
-
Cannot access inside the ASDM on PIX
Hi all:
I can't access the ASDM on the PIX when I type in
Any advice would be appreciated.
Hold on, I'm reading a release on bail of ADMS, which may have a fix for this problem.
[edit]
CSCsv12681 Details of bug
Symptom:
During the loading of ASDM, a dialog box appears that says:
"Failed to load ASDM. Click OK to exit ASDM.
Sockets without link not implemented. "
This happens when you use Java 6 Update 10 or later.
Conditions:
ASDM version 5.0 or later running on ASA, PIX or FWSM and using Java 6
Update 10 or later.
Workaround solution:
Use Java 6 Update 7.
1 found-In
5.0 (8)
5.1 (2)
5.2 (4)
6.1 (5)
4,0000 F
1.0000 F
Fixed in
6.2 (0.70)
6.2 (0.71)
6.1 (1.55) F
5.2 (4.51)
6.1 (5.51)
You can use this version based on report above.
ASDM - 61551.bin
-
VPN: Fulltunnel cannot access on the internet
Hi group!
We have an Asa 5505 in our basket.
I want to connect our office via vpn to our Asa. It should be a fulltunnel, because in our office many ports are blocked by our provider and I want to use our rack-public interface and therethore a split tunnel is not really good.
But if I accumulate a fulltunnel I have no connection to the gateway. (Inside) rack servers can access outside.
I have attached our config. Thanks in advantage!
Gerd
Could not properly read your config, pourrait you reattach config in a readable format, but I see that your vpn pool is 192.168.0.0/24.
To access internet of RA in fulltunnel you need two statements, try adding these two declarations, and let us know how it works.
permit same-security-traffic intra-interface
NAT (outsisde) 1 192.168.0.0 255.255.255.0
Rgds
-Jorge
-
VPN clients cannot access to the vlan
Hello
I just changed my flat lan to a virtual LAN environment multi, but now I need help to get to my VPN back working again as the VPN user can access servers that are not on the vlan 'door '. I've read enough to know that it is probably associated with NAT, but I'm not sure where to put this information.
Does go in the NAT, associated with the E0 interface (outgoing internet gateway), to the vlan10 (vlan router is actually on) or can I create a new one and apply it to the crypto ipsec and isakmp side of things that use VPN users?
My network is configured as such...
VPN client - Router1811 - split trunk - C3550 - 12G - shared - resources multiple C3550s - servers/Wstns
The router subnet 192.168.10.0 as all switches, VLAN is set up through the 12 G and all other switches as vtp "vtp clients", including the router. The user can get to the 10 subnet and any server on it, but not to the"farm" on the subnet 192.168.11.0.
I noticed Federico has been working on something very similar to this... but any help would be appreciated.
Thank you, Don
Hi Don,
Please mark this discussion as resolved if there is no other problem with this VPN.
See you soon,.
Nash.
-
Received an invitation for Enterprise Dashboard. He accepted and following the procedures outlined. Now, I get "access denied" errors Read the other discussions in the forum about it but can't find a solution. When I try to accept the invitation again, its said to another user agreed. Any ideas on how I can fix this and connect to Enterprise Dashboard? Thank you in advance. (Federal official stuck using the Explorer 11)
Looks that you have been invited as an end user rather than as an admin, in which case you don't need to log on the dashboard (this is only for admins). To use the right software connect when prompted.
-
My Datacenter configured as follows:1. physical switch connected to 3 physical server.
vCenter Server IP: 192.168.10.10
two physical hosts ESXi: IP: 192.168.10.11/12.
2. my laptop connected to the physical network, IP: 192.168,10.100.
3. my two physical hosts configured with a Standard vSwitcher0, VMNIC0, portgroup MYLAN uplink vLan ID = 162, vmk0 vLan ID = 162.
4. I created two nested ESXi vHost on the two physical host, assigned 192.168.10,101/102 IP, gateway 192.168.10.1
5 standard vSwitch0 on two vHost, only NETWORK VM portgroup with ID vLan by default = 0.
6. I have create computer virtual the virtual server nested and assigned to the VM using VM NETWORK, also assigned the IP address: 192.168.10.201, gateway 192.168.10.1
But my VM, I cannot ping 192.168.10.1, also I can not ping the virtual machine (x.x.x.201) from my laptop.
I can ping my vHost nested two of my laptop, can also connect to the console of the virtual computer through my vHost nest.
my virtual world, my network is configured as it IS (external swith marking).
my world physical host, my network is configured as a VST (virtual switch tagging).
My Setup must in principle be correct, but it does not work.
I am a newcomer to the world of VMWare nested. I'm appreciated for any suggestions and help.
The vSwitch on the physical host must be configured to allow the promiscuous mode and forged passes.
Maybe you are looking for
-
I have a new mac book pro, I need to copy my stuff from my old mac pro book
Hi all, I just splashed the money and got myself a new mac book pro, without the DVD player. Now I would like to transfer all my stuff from my old book of mac pro, the easiest way and fastest possible. while I was in the store to spend my money, the
-
Satellite P100-221 - where can I buy it?
HelloI'm looking for a shop in London with Satellite P100-221. Do you know where I can buy this model?
-
What compactDAQ for optical encoder module
If I have an optical encoder with a resolution of half a plan on using it for the speed or position and degree, can anyone recommend a CompactDAQ/CompactRIO module? LabVIEW would be fast enough to keep up if Let's say your device runs at 50 rpm?
-
Need help recovering data of the target in real time. Using NI 9233
I have a cRio-9012 with 9233 module. I have recently setup of the software for the computer and the target. I have also gone through and set up the "NI 9233 start-up scan mode" to use on my controller. However I couldn't really get the execution of v
-
8600 premium: prem Usless 8600
Probably one of the worst printers never had at this point ive... I have a black cartridge full again in this useless machine and it keeps realize that his depleted despite printing a full page of black every time I told it to print something. Then p