Cannot communicate with scanner hp virtual windows XP wireless.

Similar Questions

• CanoScan 88ooF error report, "cannot communicate with scanner.

  When I try to use my scanner I get the error report, "cannot communicate with scanner, make sure it is plugged and truned on.» When I go into Windows Device Manager I can see it, and when I click on the buttonn properties, it says that the device is functioning properly. I downloaded the latest version of the software driver etc and I uninstalled and re installed again but I still get the same error report.

  I use Windows 7, 64-bit version.

  

  Above is I get the error message.

  After two days of fruitless efforts, I found my own solution. I downloaded and installed VueScan x 64 and it works a treat. I think that the problem I've been is due to the fact that the scanner driver is 64-bit and the programs that install are 32-bit, even if the scanner driver works perfectly fine 2 bit programs do not see.

• Canon PIXMA MP160 error message 'cannot communicate with scanner.

  I have a Canon PIXMA MP160, who worked during the scanning of the printer on my computer. Now, I get an error message "cannot communicate with scanner. Installation scanner no longer works. The Canon site suggested looking in the Windows directory for a file named ' USBSCAN. SYS, but my research has not found it

  Installation scanner said that all the files are in place until it reaches the end.

  I received an update of windows on 31/10/2011. It works

• MG6120 - cannot scan error "cannot communicate with scanner.

  Hi, I have a Mac Book Pro with OS 10.10.5 (Yosemite).  I have the Canon MG6120 printer.  Since I updated to Yosemite, I'm more able to scan using the MP Navigator ex software  I get the following error message:

  "Cannot communicate with the scanner.

  Cable may be disconnected or scanner may be turned off.

  Check the status.

  Scanner driver will be closed.

  2.1.0.

  The only way I can scan is by using the touchpad on the printer and saving the scan on a USB key.

  I went to the page support and downloaded the latest drivers, but he has not made a difference.  I need to remove the printer and re - add again?

  You will appreciate greatly any help or advice.

  Thank you very much

  Alice Berman

  Hello.

  If the printer is used via the USB port, make sure that the printer is connected directly to your computer.  Avoid using USB hubs or extension to connect devices.

  If the printer is used with wireless, please proceed as follows to save your scanner to work wireless on Mac:

  1. click on the "Canon IJ Scan Utility" icon on the top of your screen and choose "display settings." (Located near the clock, looks like a scanner open with an arrow below). For the latest operating systems, the program can be located in the Canon Utilities listing applications.

  2. in the next screen, make sure that the network version of the printer is selected instead of "do not use". The network version will be a long series of numbers next to him.

  3. click on "Scan-of-operation-panel-settings".

  4. a new window should appear, make sure that the printer is selected, and then click OK.

  5. click OK to exit the utility.

  Once done, do the following:

  1. open the Application folder.

  2. open Canon Utilities.

  3. open MP Navigator.

  4. Once opened, click on the "Settings/preferences" button at the bottom.

  5. in the menu drop-down "Product name", select the Network Scanner.

  6. click OK at the bottom.

  Once done, try to scan from MP Navigator.

  If you continue to have difficulties, find more help contact us.

• Tecra P11 cannot communicate with scanner

  6 months ago, I replaced my old Tecra A3 with a P11. For almost all of this time, it was a lottery if the P11 would communicate with the scanner function (fine print) of my Canon MP170 printer/scanner. The only reliable method that I had was back system restore at the date of purchase--> do the scanning-> undo system restore. What a pain!

  This printer was showing it's age so I bought a new Epson. Same problem, the computer can talk with her to print but cannot communicate to scan. I changed the USB cables and ports, made what Epson has suggested, but to no avail. Tips last Epson a me summer "it must be a computer problem.

  Anyone else had a similar experience? More important still, you haven't solved the problem? I have no desire to return to the merrygoround of system restore.

  Hello

  It is really strange, and the whole is illogical for me.
  How it can work with the settings but not later? What happens during this time?

  Last month I bought the large HP device with printing, scanning and the adjustment function. I use it with my Tecra A11. The entire configuration was completed in 10 minutes. I ve tested with USB cable and also with wireless LAN functionality. No problem at all.

  In my opinion the most important is the pre-installed software that you get from the manufacturer.
  If Epson believe it must be computer you asked what that would be. I mean they should have sufficient experience with own products and they have tested the software they offer.

  Unfortunately I can't help you with this, but I will follow this thread to see what the problem was.

  If you will be able to find a solution please let us know.
  Good luck.

• N911a HP Officejet Pro 8600 error scanner cannot communicate with the computer.

  Original title: is anyone has the sweep of HP Officejet Pro 8600 n911a problems when you use Windows 7 Pro?

  Just bought this laptop of HP Pavilion dv6-7138us, and had the updated operating system upgraded to Windows 7 Pro, directed by Office Depot until I take possession.  The all-in-one HP Officejet Pro 8600 n911a (bought a few months ago) will be analyzed to this laptop.  I can't access "managing the scan of the computer."  When I try to open the scanner of the icon, the message begins with "scanner cannot communicate with the computer."  I was on the HP support forum, tried to uninstall and reinstall the driver, even tried to download the driver on the net, you run printing HP & scan doctor, tried all disconnect them reconnect restart options, all without success.  The functions of printer normally with this laptop and the printer function scanner AND correctly on other two laptops running Windows XP Pro.  Which makes me suspect that this is a problem Windows 7 Pro.  Could this be just?

  My apologies if this isn't the right forum for my problem.  Please redirect me if this is the case.

  Any real help will be GREATLY appreciated.  It's so frustrating!

  Thank you.

  Hello

  1. you have any security program installed on the computer?

  2 did you a recent software or changes to the material on the computer?

  Method 1:

  I suggest you to disable any anti-virus program and check if the problem persists.

  http://Windows.Microsoft.com/en-us/Windows7/disable-antivirus-software

  NOTE: Antivirus software can help protect your computer against viruses and other security threats. In most cases, you should not disable your antivirus software. If you need to disable temporarily to install other software, you must reactivate as soon as you are finished. If you are connected to the Internet or a network, while your antivirus software is disabled, your computer is vulnerable to attacks.

  Method 2:

  You can also run the printer Troubleshooter and check if it helps.

  Open the printer Troubleshooter

  http://Windows.Microsoft.com/en-us/Windows7/open-the-printer-Troubleshooter

  Method 3:

  I also suggest to try to run the System File Checker scan on the computer. The scan will replace all the Windows files corrupted with new ones.

  Click on the link mentioned below for further guidance on the scanning of the file system Checker

  http://support.Microsoft.com/kb/929833

  See also:

  "The computer cannot communicate with the scanning device" Error message in Windows Vista

  http://h10025.www1.HP.com/ewfrf/wc/document?CC=UK&DLC=NL&DocName=c00852756&LC=en

  I can't scan in Windows using the HP software

  http://h10025.www1.HP.com/ewfrf/wc/document?DocName=c02661093&tmp_task=solveCategory&cc=us&DLC=en&LC=en&product=4323659

  Hope this helps and let us know if you need more assistance. We will be happy to help.

• Windows cannot communicate with primary dns server

  Hey everybody.  I have a home network, wired PC, 1 wifi 1.  WiFi works fine.  wired network printers work well, other computers (laptops work fine both wired and wireless.)  I have a PC (VISTA), which now gives me the "windows cannot communicate with primary dns server.  This has happened a couple of times, but a reboot fixed things.  Once I had to change primary dns server from automatic to 208.67.222.222 (who got to this site), it worked.  Now, the same error, but nothing works.  I have tried in both directions between the DNS auto numbers listed here, also, have tried the following:

  ipconfig/flushdns
  ipconfig/registerdns
  netsh interface ip reset reset.log
  netsh int ip reset resetlog.txt

  and had windows try to reset the DNS of countless times.  Nothing works.  The upgrade to W7 eventually will correct this problem?  Another question, my wife insists on the use of AOL software (I know, I know), even if all that she uses to is by e-mail.  She says she loves interface.  A chance that caused this problem?

  Hello

  1. have there been recent changes to the system before the show?

  2. the problem occurs only with specific applications?

  Method 1:

  Follow the link and follow the steps proposed by Shekhar S and check if it helps.

  http://answers.Microsoft.com/en-us/Windows/Forum/Windows_7-networking/cant-communicate-with-primary-DNS-server/9043f785-2f4e-4CC1-ADF5-6ba5ca413749

  Method 2:

  Follow the link below and follow the steps. Check if it helps.

  Windows Vista cannot obtain an IP address from certain routers or some non-Microsoft DHCP servers

  http://support.Microsoft.com/kb/928233

  I also suggest you to run the command in the command prompt and check where the Windows Vista computer is pointing to DNS and DHCP.

  ipconfig/all

  Post back with the results in this thread.

  Let us know if it helps.

• The printer (Lexmark x 5470) cannot communicate with the computer (Windows Vista Home Premlum)

  The printer (Lexmark x 5470) cannot communicate with the computer (Windows Vista Home Premlum).  I tried these solutions below, but it still does not:

  1. ensure that the printer is powered.

  2 disconnected then reconnected the power cable from the printer.

  3 unplugged then replugged the USB cable.

  4 checked Windows Firewall setting to ensure the communication of the printer is not block.

  5. restarted my computer.

  Please help me solve this problem.

  Thank you!!!

  Have you just tried reinstallling your printer yet? Even if it was working before, file corruption or other problems can sometimes be cured by doing this?

• Photosmart 6520: printer/scanner cannot communicate with the computer

  Attempt to analysis I get the message that the scanner cannot communicate with the computer. I found a 'solution' of Provost. followed the instructions, i.e. cleaned-uninstalled, downloaded the recommended download, but when I tried to install it I get the message: this volume does not meet the requirements for this update. So now I find myself with a softwareless and so unusable printer. Help, please. OS is Snow Leopard 10.6.8

  I messed around with it a bit nd git to work, finally. So startrekker, I give you a thumbsup kudos.

• Unable to connect to the wireless network, Windows error cannot communicate with the device or the reaource (primary DNS server)

  Original title: internet connection problem

  Hey,.

  I use a wireless connection at home, it works very well in my android and apple gadget, but it does not work for my laptop. It is said:

  1. Windows cannot communicate with the device or the reaource (primary DNS server)

  2. the connection between the Internet and your access point, router or cable modem is broken

  3 problem with access point or wireless adapter

  I think it's an effects of virus or something?  Because yesterday it works really well. How can I fix? Thank you very much

  Hello Hildegard Lydia,

  You may experience this problem for a number of reasons. Some common problems that can cause these problems are: drivers damaged or incompatible, updates missing, network connection settings, hardware problems or software or TCP/IP can sometimes be damaged or corrupted.

  What is the brand and model of your computer?

  Please follow the steps mentioned below:

  Method 1: a component of the Internet connection on your computer is a package of instructions called TCP/IP. TCP/IP can sometimes become damaged or altered. If you can't connect to the Internet and you have tried all other methods to solve the problem, TCP/IP can be causing it.
  I suggest you try to reset the TCP/IP stack.
  http://support.Microsoft.com/kb/299357

  Method 2:

  I suggest that you refer to the following link:

  Why can't I find a wireless network?

  http://Windows.Microsoft.com/en-CA/Windows/cant-find-wireless-network#1TC=Windows-7

  Method 3:

  See the steps in the following link and check:

  Wireless and wired network problems

  http://Windows.Microsoft.com/en-CA/Windows/network-connection-problem-help#network-problems=Windows-7&V1H=win81tab1&V2H=win7tab1&V3H=winvistatab1&v4h=winxptab1

  Please an update on the status of the issue to help you further.

• Windows cannot communicate with the device he resourse (primary DNS server).

  Original title: primary dns.

  Help, please

  Windows cannot communicate with the device he resourse (primary DNS server)

  Please help me solve this problem

  If you see a 'FON' signal wifi on your PC and you have signed up to "FON", you should be able to connect to it.

  If you look on your BT router (or router you pay BT for the primary connection) on its homepage it should show something like "State of the Wifi BT. If it is active, you should be a member "FON", if it is not active then you need to register and agree.

  BT has their own support forum if you have not already tried it - https://community.bt.com/

  See the FAQ here - http://www.btfon.com/support to ensure that you are connected properly.

  in particular:

  How can I connect once I connect to the correct Wi - Fi network?

  Once you are connected to the correct wireless network, launch your browser. This should load the Fon login page. Select Fon among the three options on the login page, enter your e-mail address and password and sign in. Launch another browser and you are ready to access the Internet

• Many problems with Windows, Windows cannot communicate with the device or resource (primary DNS server)

  Many problems with Windows, Windows cannot communicate with the device or resource (primary DNS server), Internet Explorer browser does not.

  Hi Rachel,

  I understand that when you try to connect to the Internet, you get error "Windows cannot communicate with the device or resource (primary DNS server)", what other issues you are faced with Windows?

  • Using a cable or a wireless Internet connection?

  DNS (Domain Name System) translates the URL in IP (Internet Protocol) addresses (and vice versa). For example, if you type http://www.microsoft.com into the address bar in your web browser, your computer sends a request to a DNS server. The DNS server translates the URL to an IP address so that your computer can find the Microsoft web server.

  I suggest you to follow the methods in this article and check if it helps.
  http://support.Microsoft.com/kb/2779064/en-us

  Let us know if it helps.  If the problem persists, please answer, we will be happy to help you.

• When you use network troubleshooting in Windows, get message Windows cannot communicate with primary dns server

  Original Title2: Windows 7 - Internet
   
   
  Original title: can someone help me?
  I use a PC at home with Windows 7.  Whenever the failure at home, I have problems connecting to the Internet. Whenever I try to go on Youtube or another website, I get "Internet Explorer can not display the webpage." Now, my internet and router are configured correctly, then why is what is happening? I ran Diagnostics and got the "Windows cannot communicate with primary DNS server." I tried to reset the TCP/IP settings. It did not work and I did three times! I tried to check the properties of my network when I went to diagnose the problem, he threw some stuff on the property sheets open and close before you reopen the properties. If someone could give a foolproof solution for this annoying internet problem I would really appreciate it. Thank you.

  Hello

  Welcome to the Microsoft community!

  While using the network troubleshooter utility in Windows, you get message that Windows cannot communicate with primary DNS server.

  What is the exact message that you get when you try to check the settings of network domestic?

  I suggest you to change network settings:

  Step 1: change network settings of the router

  a. connect to your router (by typing 192.168.0.1 or 192.168.1.1 in the address bar) and connect. Check your user manual or documentation if you don't know the references of logon.
  b. make sure you are in Setup-> basic configuration category.
  c. scroll down until you see "DHCP Server" - if it is disabled, select 'enable '.
  d. enable DHCP if you want, you can change the number that starts the DHCP IP assigning. (This is optional)
  e. use the DNS servers provided by your ISP. There are many DNS servers out there. It is preferable to use your ISP if possible.
  f. scroll down and click 'Save Settings'.

  Note: The procedure may slightly vary with different routers. You can see the manual or contact ISP for assistance.

  Step 2: change in the computer network settings

  a. click on start and then Control Panel.
  b. go to the networking and sharing Center and then click on change adapter settings.
  c. right-click on connection to the Local network and select Properties.
  d. Select Internet Protocol Version 6, and then click Properties.
  e. Select obtain DNS server automatically an address and press Ok.
  f. Select obtain IP address automatically.
  g. Repeat steps for Internet Protocol version 4 as well.

  I hope this helps. If the problem persists, let know us and we would be happy to help you.

• Windows cannot communicate with devices or resources

  original title: novatel wireless ovation usb mc769

  Sometimes, using my wireless, novatel, this message will appear as a troubleshooting tool:

  WINDOWS CANNOT COMMUNICATE WITH THE DEVICES OR RESOURCES (MAIN DNS SERVER)

  What does that mean?  I have to update a program?

  Hello

  You can try to follow the steps mentioned by Shekhar S published on Tuesday, February 9, 2010 19:41 to fix the problem:

  http://social.answers.Microsoft.com/forums/en-us/w7network/thread/9043f785-2f4e-4CC1-ADF5-6ba5ca413749

• Host cannot communicate with all other nodes in the cluster virtual SAN allowed

  I get this error after you apply the latest patch:- http://kb.vmware.com/selfservice/microsites/search.do?language=en_US & cmd = displayKC & externalId = 2135115

  So all the hosts are now review: VMware ESXi, 6.0.0 3380124

  After the reboot, I get the error message on the host cannot communicate with all other nodes in the cluster active virtual san...

  However, the VSAN health check is green, 'get esxcli vsan cluster' shows all 6 members of the cluster ok... and if I reboot a crowd happens ok without the error... so if I reboot another host, it will come without the error... but then the host on which I rebooted before it displayed the error...?  So I can't ever get more than 1 host without the error after a reboot.

  I checked multicast that removes ok, in fact all of the checks in contradiction with the fact that why I get this error...

  Someone at - it ideas? Could this be the latest patch...

  Paul...

  Hello, this has been repeated here: 6.0 U1b - hosts cannot communicate thanks, Zach.