cannot detect external display

Similar Questions

• My Aspire V7 582PG cannot detect external monitors

  I recently bought an Aspire V7 582PG, put in a new SSD and then installed Windows 8. The laptop works well, except that it cannot detect external monitors (in Control Panel, I get "Has not detected a different view".) I tried with 2 monitors (different models) that are known to work, via HDMI and VGA.

  I thought it might be a driver problem. Device Manager > 'Graphics cards' show 'Display card base Microsoft' and 'NVidia GEForce GT 750 M. The two drivers are up-to-date. 'Monitors' shows 'generic PnP monitor", which is also updated.

  Then I went to http://us.acer.com/ac/en/US/content/drivers to download the driver for my model. The only one who had the relevant air was:

  Monitor

  ELANTECH

  The HID monitor drivers

  1.1.5

  Installer here: http://global-download.acer.com/GDFiles/Driver/Monitor/Monitor_ELANTECH_1.1.5_W8x64_A.zip?acerid=635...

  But when I unzip and run the Setup window closes a few seconds; I think it hangs, rather than installing correctly.

  Any suggestions?

  My Acer tabs they need additional drivers to recognize the HDMI port.

  I think having unzipped in a directory and open a DOS window with admin rights and run the application inside that. At least if an error occurs, you should be able to see. Sometimes just doubleclicking opens and closes a window so fast that you do not see the error.

  Also in looking at support for a 'ultra' V7, I see several drivers for the chipset VGA and monitor. All may be required for the video display to work.

  You see multiple devices when you press Windows-P?

• detected external display suddenly stopped working - displays black screen

  original title: detected external display suddenly stopped working

  Hello

  I have searched in several forums, but have not been able to completely solve this problem.  It has been set provisionally and has not yet.
  This system I have:
  HP TouchSmart tx2 tablet pc with Windows Vista Service Pack 2 x 64-bit (Home Premium)
  AMD Turion (tm) X 2 Ultra Dual-Core Mobile ZM - 82, 2.2 GHz
  ATI Radeon HD 3200 graphics card
  I have been working for more than a year with a monitor flat screen Dell ST2310 external monitor and works very well with the setting "use external display only.  From one minute to the next two screen went black so I forced a restart and again the same problem.  I decided to manually disconnect the external monitor by unplugging the VGA cable from the laptop that turns on automatically to the main display as it would if I am disconnected display.  When I connected the VGA cable again the same question in the two screens were entirely black.  I unplugged once more the VGA cable if I could change the settings in Windows mobility.  I plugged back in the VGA cable after changing the settings of "external display only" to 'mirror' devices and after playing for a bit, with the Windows Mobility Center, I had the external display to work again my regular settings: "external display only.  This solution lasted a day and now works in the main screen and the external screen is completely black.
  I tried in vain to solutions:
  -Change VGA cables continues to experience the same issue.

  -Tested according to the specifications and Dell monitor Monitor works fine if the backlight is not the problem.
  -Records update for ATI Radeon HD 3200 graphics card and driver generic PnP Monitor and Dell ST2310.
  -Uninstalled ATI Catalyst Manager and re install now as AMD Vision Engine Control Center.
  -Checked AMD Vision Engine Control Center recognizes the connected external display.
  -Uninstalled the driver Dell ST2310 and re installed the driver.
  -On the screen settings have tried to extend the desktop on the external screen (second)
  Now, this is what's going on and don't know how to fix it:

  -Windows Mobility Center detects a monitor external, even when the VGA cable is disconnected.

  -When it detects the external display it sometimes detects it as DELL ST2310, sometimes as a generic Non - PnP monitor.

  -Sometimes under "Monitor" in the Device Manager, there are several monitors generic Non - PnP contained also the Dell ST2310 and generic PnP monitor.

  -When the external monitor is connected, the screen is completely black and does not work even after changing the settings Windows Mobility or Fn F4.
  Help!

  Hello
   
  I also suggest you to update the BIOS. Visit the manufacturer for more information.
  http://Windows.Microsoft.com/en-us/Windows-Vista/BIOS-frequently-asked-questions
   
  WARNING:
  BIOS change / semiconductor (CMOS) to complementary metal oxide settings can cause serious problems that may prevent your computer from starting properly. Microsoft cannot guarantee that problems resulting from the configuration of the BIOS/CMOS settings can be solved. Changes to settings are at your own risk.
   
  See also: http://h10010.www1.hp.com/ewfrf/wc/document?docname=c01881110&tmp_track_link=ot_recdoc/c00678157/en_us/c01881110/loc:4 & cc = us & dlc = en & lc = en & product = 352607 #N624
   
  Thank you

• ACER Travelmate 5760 with Windows 10, cannot detect the external projector

  I have an ACER Travelmate 5760. I have upgraded to Windows 10, because Microsoft is launching a few checks and said that I would be able to upgrade. But now, the laptop cannot detect an external projector or monitor. Is there a driver that I need to improve?

  Thank you

  Winifred

  When you connect your projector, if you press the windows logo key + p, are you able to select expand and check if the projector work?

  also, if you right-click on your desktop and choose the settings display, is the acknowledged projector?

  How to connect the projector?

  on the drivers, you try to uninstall the real Intel VGA driver and reboot with your laptop connect on the web and let windows update find new drivers as appropriate.

• When I cut my computer on it comes up telling me that the battery cannot be detected or displayed.

  original title: battery problem

  To all,

  When I cut my computer on it comes up telling me that the battery cannot be detected or displayed.

  I unplugged the battery taken power and put it back it, that did not work,

  The battery is fully charged and when I check the battery in the control panel for the strength of the battery, the system is telling me, it is fully charged and there is nothing wrong with my battery.

  Then I ask why I get this error when I start my computer.

  Can anyone help me on how can I do to fix it.

  Thank you

  Russell Froedge

  Hello

  Check with support from the manufacturer of their books online and the drivers and their forums system
  (as applicable) for known issues. Some manufacturer issued BIOS and other updates to help the battery
  problems.

  Control Panel control - plan change Options - power plans - power - advanced settings
  Parameters for the drainage and the use of parameters (this is how much to use and not how much or how)
  long to load).

  In fact, what causes a lot of wear on a battery empties it too low on several occasions. With today
  systems overload are not a problem.

  Here are some tips to help and troubleshoot battery issues.

  Old battery? Unplug the power to the computer - remove the battery and clean the contacts with a pencil
  eraser (do not use this, if your battery is fine slots - just clean up the edges of the knife which fit in)
  them and be careful). Batteries are old, or it could be a problem with the computer.
  Check with the support of the machine system, and many of them have on line forums.

  New Lithium-Ion type battery usually last longer if you do not unload then less than 30%
  However on a laptop that not extend their life a lot. Best is to use the a/c adapter
  When this is possible.

  I use the free version of BatteryBar to monitor my battery. Click on the green button on the
  Yellow box on the right side of the page to download the latest stable version.

  BatteryBar - free version available
  http://osirisdevelopment.com/BatteryBar/index.html

  Another good program

  Vista battery saver - free
  http://www.codeplex.com/vistabattery

  Problems with the lives of its use and the battery of power - Mr Fixit
  http://support.Microsoft.com/GP/windows_battery_power_settings

  You can also check with the manufacturer of system and forums that many use their own
  proprietary software to monitor the battery and they could be known problems with your battery.

  ============================================================

  Try this - to make a Restore Point

  How to create a Vista System Restore Point
  http://www.Vistax64.com/tutorials/76332-system-restore-point-create.html

  How to make a Vista system restore
  http://www.Vistax64.com/tutorials/76905-System-Restore-how.html

  Then Control Panel - Manager of devices - Batteries - Double click on each item - drivers - tab
  Update the drivers (which can do nothing) - then do a right click and UNINSTALL each.
  RESTART which will update the driver stacks.

  Problems with the lives of its use and the battery of power - Mr Fixit
  http://support.Microsoft.com/GP/windows_battery_power_settings

  I hope this helps.

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle=""><- mark="" twain="" said="" it="">

• Portege Z30 - A - 18 M - cannot set the native resolution on the external display

  Hello

  I tried to connect two different displays full HD to my Portege Z30 - A - 18 M and I was unable to set the native resolution - maximum resolution I can put for those is 1680 x 1050... I was not so surprised by the first that I had a few problems with a native resolution when I connect to the laptop computer Satellite I had before. But then the same thing happened when I tried the other view.

  I thought that this notebook can handle a higher resolution external... Is there a way to force the native resolution of the external display in Windows 7?
  Thank you!

  Just a question: have you plugged your Portege with HDMI cable and use only the HDMI option?
  With other words went from the desktop to the external display only computer?

  I don't have this machine, but I think you should be able to see the desktop on an external device to the HD full 1920 x 1080 resolution.

• Tecra S2 cannot switch to the external display

  With my Tecra S2 and when it is docked in the Port Replicator APR - III, I used to be able to connect my external (via DVI) display so that it was to automatically screen output to we by default, not only to the windows startup screen (Yes, I noticed the topic on the forum at the start of windows) but also when display login screen and beyond.

  Only problem now is that there is no more than anything, she now only sends the output to the external display when starting and then switches back to the computer screen displaying the screen Windows login and when you are connected to Windows.
  Also after commissioning and connection, FN + F5 does not at all, even when you switch to DVI, display does not illuminate.

  I feel that either the nVidia properties settings (double screen, unique, etc.) or the Mobile Extension Manager have something to do with it.
  Anyone who knows the answer / solution to this problem?
  Experts on the Mobile Extension Manager or several monitor in nVidia settings with of Toshiba Tecra?

  Thank you

  Arjen

  Hello

  Well, as I know it is not possible to set the external monitor as a default monitor.
  I use a Satellite phone and sometimes I plug it into the external monitor and use the extended desktop option.
  During notebook startup procedure the windows boot image will appear on the second screen, but the user name and the operating system appears on the screen of the laptop.
  I think you can use the external monitor but you can't set it as a default monitor and you can use it if the operating system has been released.

• kernel_task runaway (from 300 to 600%) CPU with 2 external displays

  I have a MacBook Pro (retina, mid-2012), and for a year and a half, I've had episodes fighter during the kernel_task suddenly begin to consume all processor CPU (from 300 to 600%), is the response of the system so slow it is impossible to use.  I experience these episodes throughout the front 1-2 years that the machine went from Yosemite El Capitan and now Sierra.

  Normally, I use my MacBook with two external displays, both at work and at home.  At work, I have two external screens of Lenovo, and at home, I have two screens Apple (Apple Cinema Display 27-inch and 27-inch Apple Thunderbolt Display). I discovered that this kernel_task high CPU usage can only be stopped by disconnecting one of the external screens.  After unplugging an external display, the kernel_task subsides immediately to normal (< 5%).  After a few minutes, I can reconnect the 2nd external screen and proceed normally (sometimes for days, sometimes for hours, sometimes for a few minutes) until the kernel_task pulls up to 300-600% again.  The use of the high CPU kernel_task never happens unless I have two external displays connected.

  Note that since I upgraded to MacOS Sierra fugue kernel_task CPU frequency has increased considerably: of 1 kernel_task runaway every several days to a runaway almost every 10 minutes or so.   I don't have a reason this frequency has increased, but the runaway condition seems to have worsened by the fact that the photoanalysisd daemon is running like crazy on my grand (72 000) library of Photos.

  Also note that I started in recovery mode and have re-installed MacOS Sierra, and it has no effect on the runaway kernel_task.

  Any ideas on how to fix this resumption of kernel_task of all my CPU?

  I have attached my EtreCheck system report below.  This report was captured with two attached external displays.  At halfway while generating a report, the kicks and started kernel_task hogging CPU again.

  EtreCheck version: 3.0.5 (309)

  Report generated 2016-09-25 14:24:02

  Download EtreCheck from https://etrecheck.com

  Time 07:59

  Performance: Below average

  Click the [Support] links to help with non-Apple products.

  Click [details] for more information on this line.

  Problem: Computer is too slow

  Description:

  Sometimes, while working with my MacBook connected to two external displays, the kernel_task pulls up to 600 to 800% CPU and stays there until I unplug at least one of the external screens.  After disconnecting, the kernal_task subsides immediately to normal (< 5%).  After a few minutes, I can plug the 2nd external screen and proceed normally (sometimes for days, sometimes for hours, sometimes for a few minutes) until the kernel_task pulls up to 600 to 800% again.  The use of the high CPU kernel_task never happens unless I have two external displays connected.

  Hardware Information: ⓘ

  MacBook Pro (retina, mid-2012)

  [Data sheet] - [User Guide] - [warranty & Service]

  MacBook Pro - model: MacBookPro10, 1

  1 2.6 GHz Intel Core i7 CPU: 4 strands

  16 GB RAM not extensible

  BANK 0/DIMM0

  OK 8 GB DDR3 1600 MHz

  BANK 1/DIMM0

  OK 8 GB DDR3 1600 MHz

  Bluetooth: Good - transfer/Airdrop2 taken in charge

  Wireless: en0: 802.11 a/b/g/n

  Battery: Health = Normal - Cycle count = 242

  Video information: ⓘ

  Graphics Intel HD 4000

  NVIDIA GeForce GT 650M - VRAM: 1024 MB

  Color LCD 3840 x 2400

  LED Cinema Display 2560 x 1440

  Thunderbolt Display 2560 x 1440

  Software: ⓘ

  macOS Sierra 10.12 (A 16, 323) - since the start time: about an hour

  Disc information: ⓘ

  APPLE SSD SM512E Disk0: (500,28 GB) (Solid State - TRIM: Yes)

  EFI (disk0s1) < not mounted >: 210 MB

  Recovery HD (disk0s3) < not mounted > [recovery]: 650 MB

  Boromir (disk1) /: 499,05 (Go 140,24 free)

  Storage of carrots: disk0s2 499.42 GB Online

  USB information: ⓘ

  Apple Inc. FaceTime HD camera (built-in)

  Apple Inc. Apple keyboard / Trackpad

  Apple Inc. BRCM20702 hub.

  Apple Inc. Bluetooth USB host controller.

  Apple Inc. Apple LED Cinema Display

  ISight Apple Display Inc.

  Apple Inc. Audio display

  Apple Inc. FaceTime HD camera (display)

  Apple Inc. Apple Thunderbolt Display

  Apple Inc. Audio display

  Lightning information: ⓘ

  Apple Inc. Thunderbolt_bus.

  Thunderbolt Inc. Apple display.

  Configuration files: ⓘ

  / etc/sudoers, 2299 but file size expected 1563

  Guardian: ⓘ

  Mac App Store and identified developers

  Kernel extensions: ⓘ

  / Applications/Beats Updater.app

  com.beatsbydre.BeatsDFUSupport [no charge] (2.1.0 - SDK 10.10 - 2015-10-29) [Support]

  /Applications/proxifier.app

  [no charge] com.initex.proxifier.macosx.kext (2.15.2b1 - SDK 10.7 - 2015-09-10) [Support]

  / System/Library/Extensions

  [no charge] com.makemkv.kext.daspi (1.5-2016-09-25) [Support]

  Startup items: ⓘ

  TiVoDesktop: Path: / Library/StartupItems/TiVoDesktop

  Startup items are obsolete in OS X Yosemite

  Launch system officers: ⓘ

  [no charge] 7 tasks Apple

  [loading] Apple 156 jobs

  [running] Apple 108 jobs

  Launch system demons: ⓘ

  [loaded] com.apple.jetsamproperties.Mac.plist (2016-08-25) [Support]

  [no charge] 41 tasks of Apple

  [loading] 153 jobs Apple

  tasks of Apple 109 [performance]

  Launch officers: ⓘ

  [cannot] com.adobe.ARMDCHelper.cc24aef4a1b90ed56a725c38014c95072f92651fb65e1bf9c8e43c37a2 3d420d.plist (2016-07-11) [Support]

  [loading] com.cisco.anyconnect.gui.plist (2014-06-10)

  com.DisplayLink.UserAgent.plist [no] (2012-08-14) [Support]

  [loading] com.google.keystone.agent.plist (2016-07-11) [Support]

  [loading] com.oracle.java.Java - Updater.plist (2013-01-04) [Support]

  Launch demons: ⓘ

  [loading] com.adobe.ARMDC.Communicator.plist (2016-07-11) [Support]

  [loading] com.adobe.ARMDC.SMJobBlessHelper.plist (2016-07-11) [Support]

  [loading] com.adobe.fpsaud.plist (2016-08-29) [Support]

  com.backblaze.bzserv.plist [running] (2016-07-11) [Support]

  com.Cisco.anyconnect.vpnagentd.plist [running] (2014-06-10) [Support]

  com.DisplayLink.usbnivolistener.plist [no] (2012-08-14) [Support]

  [loading] com.google.keystone.daemon.plist (2016-09-09) [Support]

  [loading] com.oracle.java.Helper - Tool.plist (2013-01-04) [Support]

  [loading] com.sharpcast.xfsmond.plist (2013-11-30) [Support]

  User launch officers: ⓘ

  com.backblaze.bzbmenu.plist [running] (2016-09-25) [Support]

  com.vladalexa.MagicPrefs.plist [running] (2016-09-25) [Support]

  Items in user login: ⓘ

  iTunesHelper Application (/ Applications/iTunes.app/Contents/MacOS/iTunesHelper.app)

  HWMonitor Application (/ Applications/HWMonitor.app)

  Hidden CPULed Application (/ Applications/CPULed.app)

  Application of hidden activity monitor (/ Applications/Utilities/Activity Monitor.app)

  Dropbox application (/ Applications/Dropbox.app)

  Hidden SizzlingKeys Application (/ Applications/SizzlingKeys.app)

  Beats Updater Application (/ Applications/bat Updater.app)

  Hidden NET Monitor Application (/ Applications/Net Monitor.app)

  Plug-ins Internet: ⓘ

  FlashPlayer - 10.6: 23.0.0.162 - SDK 10.9 (2016-09-15) [Support]

  QuickTime Plugin: 7.7.3 (2016-09-13)

  AdobePDFViewerNPAPI: 15.017.20053 - SDK 10.11 (2016-08-03) [Support]

  AdobePDFViewer: 15.017.20053 - SDK 10.11 (2016-08-03) [Support]

  Flash Player: 23.0.0.162 - SDK 10.9 (2016-09-15) [Support]

  Silverlight: 5.1.20913.0 - SDK 10.6 (2014-03-07) [Support]

  JavaAppletPlugin: Java 8 update 101 build 13 (2016-08-18) check the version of

  User Plug-ins internet: ⓘ

  WebEx64: SDK-1.0-10.10 (2016-01-23) [Support]

  Safari extensions: ⓘ

  Ghostery - GHOSTERY, Inc. - https://www.ghostery.com/ (2016-03-15)

  3rd party preference panes: ⓘ

  Backblaze backup (2016-07-11) [Support]

  Flash Player (2016-08-29) [Support]

  FUSE for OS X (OSXFUSE) (2013-11-30) [Support]

  Java (2016-08-18) [Support]

  MagicPrefs (2016-01-20) [Support]

  MenuMeters (2014-10-22) [Support]

  TiVo Desktop (2009-11-23) [Support]

  Time Machine: ⓘ

  Skip system files: No.

  Mobile backups: OFF

  Automatic backup: YES

  Volumes to back up:

  Boromir: Disc size: 499,05 GB disc used: 358,81 GB

  Destinations:

  Frodo Time Machine [Local]

  Total size: 999,86 GB

  Total number of backups: 40

  An older backup: 09/09/16, 02:09

  Last backup: 25/09/16, 11:49

  Backup disk size: too small

  Backup size GB 999,86 < (disc 358,81 GB X 3)

  Top of page process CPU: ⓘ

  345% kernel_task

  56% Information System

  44% cloudphotosd

  42% iTunesCacheExtension

  30% activity monitor

  Top of page process of memory: ⓘ

  1.44 GB kernel_task

  1.18 GB com.apple.WebKit.WebContent (6)

  786 MB mds_stores

  590 MB bztransmit

  Mdworker (18) 492 MB

  Virtual memory information: ⓘ

  256 MB of free RAM

  4 pm used GB RAM (5.96 GB being cached)

  768 KB used Swap

  Diagnostic information: ⓘ

  25 sep, 2016, ~/Library/Logs/DiagnosticReports/com.apple.WebKit.WebContent_2016-09-25-134618_ 13:46:18 [redacted] .crash

  System/Library/Frameworks/WebKit.Framework/versions/A/XPCServices/com. Apple.We bKit.WebContent.xpc/Contents/MacOS/com.apple.WebKit.WebContent

  25 sep, 2016, 13:19:15 /Library/Logs/DiagnosticReports/photolibraryd_2016-09-25-131915_[redacted].cpu_ resource.diag [details]

  /System/Library/PrivateFrameworks/PhotoLibraryPrivate.Framework/versions/A/Supp ort/photolibraryd

  25 sep, 2016, 13:06:44 test - passed

  September 22, 2016, 16:03:11 ~/Library/Logs/DiagnosticReports/Microsoft Word_2016-09-22-160311_ [redacted] .crash

  com.microsoft.Word - Applications / Microsoft Office 2008/Microsoft Word Word.app/Contents/MacOS/Microsoft

  Start safe mode, use this way and see if the problem is recurring

• How to calibrate an external display for macOS Sierra?

  Hi guys,.

  seems that on my Macbook Pro after the update everything is strong and displayed correctly.

  However, on the external monitor, a 24 "AOC who was as crisp and sharp as the laptop (kind of I know) the images and the text seems to be well screwed. two attached photos to see the differences between the screens - even cannot correctly read the external monitor

  any ideas on how to solve this problem? or is irreparable? I tried to calibrate the monitor, used the old calibration profiles, etc. looks like illegible

  Thanks in advance

  Hello justme12,
  Thank you for using communities of Apple Support.

  If I understand your post that the quality of the image on the external monitor is as clear and crisp as it used to be. I understand wanting to the external monitor to be as clear as possible. I recommend using the steps in this article to help resolve this problem:

  Get help with graphical problems on external displays connected to your Mac.

  Best regards.

• Qosmio X 870-116: use of Intel / nVidia GPU internal / external display

  Hello

  I have a Qosmio X 870-116 which have 2 video cards, an Intel onboard and a more powerful Nvidia.
  My problem, I did not how to pass my screen on the Intel card and I see my Nvidia for the display external.

  Someone has an idea to pass on to my first display nvidia card?

  Thank you

  Hello

  Something like this isn't possible.
  You cannot use two cards simultaneously for internal and external display.

  First of all, you can switch between the external and internal view using the Fn + F4 (or just F4) function key

  Secondly the nVidia Optimus technology optimize the performance of the laptop perfectly without a GPU nVidia and Intel graphics card.
  Switching is automatic and requires no reboot of s for laptop.

• Can I connect simultaneously on Toshiba laptop to 2 external displays?

  Hello

  I am interested to know that toshiba laptop currently on offer support 2 external monitors simultaneously (one normal and then as dekstop extended in windows). I'm looking to replace my old configuration of the laptop and a station connected to two external monitors with a resolution of 1280 x 1024.

  I was looking on toshiba websita to
  Portégé R700-15 q
  http://UK.computers.Toshiba-Europe.com/innovation/product/Portege-R700-15Q/1089286/toshibaShop/false/

  with Port Replicator Port PA3680U-1PRP then some other laptop port replicator who but not the case on the site I could find if any concrete model supports the dual use of the two (VGA and HDMI or VGA and DVI) port

  I was looking on the the user guide at http://www.csd.toshiba.com PA3680U-1PRP Port Replicator
  http://www.CSD.Toshiba.com/cgi-bin/TAIS/support/JSP/modelContent.jsp?CT=SB&OS=&category=&MOID=2756712& rpn = PA3680U & modelFilter = PA3680U-1PRP & SelCategorie = 2756711 & selFamily = 116319
  and in the troubelshouting part, I found this:

  Cannot display information to a
  DVD-D and RGB monitor to the
  same time

  Check that the cables connecting the monitors are firmly fixed on
  both ends. Some computer models don't support DVI and RGB output
  monitors simultaneously. See the documentation for your computer
  model.

  But even if you find on http://www.csd.toshiba.com the file pdf of detailed spec and user guides, there is no information on whether they take in charge simultant output to monitors or not and what is the maximum resolution supported for this.

  Thanks for any help

  Ian

  As far as I know it is not possible to connect two external displays. I know that you can only use a port. If you want to use two screens you probably external device as Toshiba Dynadock.

  Check it out.

• Windows Media Center - why it cannot detect TV?

  I used Qosmioplayer and it detects the TV from my Sky Digibox very well signal. However, I would like to record TV with my laptop and when I try to set up the TV using Windows Media Center, it cannot detect anything. I tried every possible permutation and the manual does not give pointers...

  Why the Qosmiplayer works for the entrance to Sky TV, but not the media library?

  Please help it's driving me crazy!

  I assume you are using a lead of areal coaxial standard to connect to your sky box? If so, you need to know which way the sky is coming in the. To do this, use the Qomsio drive to search for channels and when it detects the signal from Sky, it will tell you which way it is passed on. Something like channel 36. OK, now you have this information, start the machine and go into Media Center. You must manually add this channel. As Media center works with the EPG, all channels such as the skyinput must be added.

  So, in the main menu, go to

  Settings > TV > Guide > add missing channels > add channel

  Now enter the channel name you want displayed when viewing. IE SKY.

  Now you enter the channel number 36 IE that you got the Qosmio engine. This will now be held on the next available channel. IE 6/7/8 etc. Everything do you now is go to the channel and it appears at the entrance to heaven.

  Hope this helps

• Portege M400 - XP Setup cannot detect any HARD disk

  Hello world

  I have everything, what I can and can't try. During the Installation of Windows XP cannot detect any HARD disk.

  PORTEGE M400 PPM40E-0DG0253I
  BIOS 3.8

  Installation of Vista properly with RAID, but XP installation drivers won't work for all that. I try a lot of drivers (versions even for Vista), with integration of nLite, with SD-start 16-bit back, DriverPacks. I bought no change - disk-USB, the laptop cannot see HDD. I try also with the USB-SATA external enclosure, but this without success, but I can see the HARD drive

  Any ideas?

  Somehow you lack driver SATA.
  Very good description how to prepare the CD of facilities, you can find HERE.

  This Toshiba document could be useful for you:
  http://APS2.toshiba-tro.de/KB0/HTD9401AN0000R01.htm

  If you have any other questions please let us know.

  Good luck!

• Satellite A10: RGB Port is not installed - can not use external display

  Satellite A10 the RGB PORT is not installed & cannot be used as external display. I tried to install the communication or COM 1. interrupt code. What are the possible solutions?

  Hello

  What did you mean by "not installed"?
  Generally, you don't need to install anything. You don't need any drivers for this port 3.
  Windows XP drivers should work properly.

  Please check device manager if there are errors or yellow exclamation points.
  If the problem occurs for a short time, you can try to use the WinXP restore tool.
  This tool will reduce the BONE until the start.

• Satellite L40 - installation of XP cannot detect HARD drive

  Hi, Toshiba support

  I have Satellite L40 - 18Y (PSL48E-03702NAR) with Windows Vista

  I want to install Windows XP, but I can't because my HDD is SATA and installation of windows XP cannot detect the HARD drive.

  I know that I have to update my BIOS.
  I have 2 files on Toshiba drivers download

  I downloaded their extract them & try to update the BIOS one. After that, I log in the BIOS
  I can't find (HARD drive Mode) must Mode IDE.

  How can I solve this problem?

  Hello!

  > How can I solve this problem?
  I think you find hundreds of discussions in the forum about this please use the forum search!

  A BIOS update is not necessary to install Windows XP. You only need the SATA drivers you can find in the Intel Storage Manager driver package that can be downloaded on the Toshiba site. Pilots must be integrated during the XP installation with an external floppy drive or use you nLite to create a new installation disc.

  Anyway, check this link from Toshiba which is an order exact step by step installation:
  http://APS2.toshiba-tro.de/KB0/HTD9401AN0000R01.htm

  Good bye