Cannot load a rules file in my application of HFM

Similar Questions

• blue screen after Ko 2840149, error - "STOP: c0000218 {Registry hive failure} the registry cannot load the hive (file): \systemroot\system32\config\SOFTWARE.

  After I installed security KB2840149 on a 2008 VM w/exchange server that is running on the machine of Hyper-v server 2008 I'm dead in the water w / E-mail down hard.  The virtual computer is in a reboot cycle bluescreening before I can get anywhere.  Tried the last well known - no effect.  Safe mode - so bluescreens.

  BlueScreen info:
  STOP: c0000218 {Registry hive failure}
  The registry cannot load the hive (file):
  \systemroot\system32\config\SOFTWARE
  or its log or alternation.
  It is damaged, missing, or not accessible in writing
  I saw that it was a patch of replacement for a patch that crashed a lot of PCs.  Since there is no history on this patch, I wanted to check in a see what is the best way to fix this on a virtual machine?

  Being not so deep on VM, I wasn't sure if there was a better way. But I just put the virtual machine to load 2008 iso and then made the standard repair for registry problems off the coast of the article below.

  Of http:

  If the Windows registry is slightly or moderately damaged, you may be able to restart the computer in safe mode and use system restore to restore the registry from the computer to the last known good configuration. However, if the Windows registry is seriously damaged, all types of logon will be prevented. Trying to connect to Windows causes the system fails, then restart. In this case, you will need to boot the system into the recovery instead of Windows Console. Once in the Recovery Console, you can use the Startup Repair tool. Startup Repair tool automates common diagnostic and repair of the installations of Windows tasks starts longer.

  (a) start your Windows Vista or Windows Server 2008 DVD
  (b) on the first Setup screen click Next
  (c) in the lower left corner of the screen, choose "repair your computer".
  (d) on the System Recovery Options screen, select your Windows installation and then click Next
  (e) click on "Command prompt".
  (f) go to X:\sources\recovery > startrep.exe
  (g) this will take some time but will look at any registry related issues.

• corrupted: WINDOWS\ SYSTEM32\ CONFIG\ SOFTWARE Stop: c0000218 {Registry file failure} the registry cannot load the hive (file): SystemRoo

  corrupt: WINDOWS- SYSTEM32- CONFIG- SOFTWARE Stop: c0000218 { file registry failure} the registry cannot load the hive (file): any on windows server 2003.  How can I fix this

  Hello, getin99

  For help on Windows Server, you need to create a new post on the TechNet forums at the following address: http://social.technet.microsoft.com/Forums/en-US/winservergen/threads

• The registry cannot load the hive (file): \systemroot\system32\conig\software or its log or replacing. It is damaged, missing, or not accessible in writing.

  My laptop does not start all of a sudden upward - it crosses the safe mode screen, acts as if it is loading windows (display the windows screen) then becomes to empty, followed by a very quick flash of the message on a blue screen: "the registry cannot load the hive (file): \systemroot\system32\config\software or its log or replacing."  It is damaged, missing, or not accessible in writing. "Then, he repeats the cycle.

  I looked towards the top of the error on the Microsoft Knowledge base, and the hotfix request using the recovery disk, I.  I wonder how I can get the interactive help on laptop computer file so that I can run so that it fixes the problem... (http://support.microsoft.com/kb/307545).

  Advice, that someone could give me so that I can at least get started again windows go down all the important data before reinstalling Windows would be much appreciated.

  Thank you

  Chris

  Hey Chris,

  Thank you for visiting the Windows Xp forum

  I was wondering if you run a retail or OEM of Windows version. If you are using an OEM version of windows, you will need to use the recovery options you have from the manufacturer of your computer. If you run a commercial version, feel free to follow the article in the knowledge base you have found.

  http://support.Microsoft.com/kb/307545 how to recover a corrupted registry

  I was also wondering if you have another computer to work? If so and you feel comfortable or know someone who can remove the hard drive from the computer and connect it to another computer. You can view the disk hard kit to join. Once the hard drive is connected, you can go in my computer and copy all the files to another hard disk.

  Georgio
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think

• Stop: 0xc0000218 {registry file failure} the registry cannot load the hive (file): \SystemRoot\System32\Config\Software is damaged, missing, or not accessible in writing.

  Original title: blue screen.

  My computer won't start even in safe mode... c000218 (failure of a registry file)

  Cannot load the hive (file): \systemroot\system32\config\SOFTWARE is damaged, missing, or not accessible in writing

  Hi rookiegeek,

  You did it of any material changes or software on the machine prior to this problem?

  The three possible causes of the problem are:

  (a) failure.

  corruption of file b) & defective hardware.

  (c) the problem can occur on shutdown.

  You can follow this link & check if the problem persists.

  Registry troubleshooting steps for advanced users

  Hope the helps of information. Please post back and we do know.

  Concerning
  Joel S
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

• Trying to access Windows XP on a Mac, receive stop error. failure of a file registry c000218 registry cannot load the hive (file)

  I have a Mac OSX, leopard, parallel 5 and Windows xp.   When I try to access Windows, either through boot camp or at the same time, I get the error message "stop. failure of a file registry c000218 registry cannot load the hive (file).  I bought Windows 7 but cannot get Windows Installer.

  The hard drive may be replaced . Or something is not compatible

• C0000218 {registry file failure} the regestry cannot load the hive (file)

  I have XP pro. on a Dell computer. Think that children may have picked up a few difficulties. When trying to boot into safe mode, I get "Stop: c0000218 {Registry file honor} the regestry cannot load the hive (file): \SystemRoot\System32\Config\Software or its log or replacing." It is damaged, missing, or not accessible in writing. »

  There is no disk that came with it, but I have anouther computer with the same windows. I tried to find a way to make a BOOT disk but cannot find a way. Is there a way to solve this problem with the windows disc?

  It's a pretty popular mistake these days and sometimes easy to get running, but you also want to figure out how it happened.  I always suspect Symantec/Norton products with this error, but we'll see.

  If you currently or have already had a whole isntalled Symantec/Norton products, what are the names and versions (if you know).

  Other variants are:

  STOP: c0000218 {Registry file failure}
  The registry cannot load the hive (file): \SystemRoot\System32\Config\SECURITY or its log or replacing. It is damaged, missing, or not accessible in writing.

  STOP: c0000218 {Registry file failure}
  The registry cannot load the hive (file): \SystemRoot\System32\Config\SOFTWARE or its log or replacing. It is damaged, missing, or not accessible in writing.

  STOP: c0000218 {Registry file failure}
  The registry cannot load the hive (file): \SystemRoot\System32\Config\SYSTEM or its log or replacing. It is damaged, missing, or not accessible in writing.

  I would start with a chkdsk/r since the recovery CD of Console you make (see below) and please answer a few questions...

  Maybe someday the dialog box 'ask a question' forums XP will ask these questions automatically when a new thread is started so I don't have to ask every time.  It might even be possible to solve a problem in a single response when enough information is provided.

  Please provide additional information on your system:

  Describe your current antivirus and software anti malware situation: McAfee, Symantec, Norton, Spybot, AVG, Avira!, MSE, Panda, Trend Micro, CA, Defender, ZoneAlarm, PC Tools, Comodo, etc..

  The question was preceded by a loss of power, aborted reboot or abnormal termination?  (this includes the plug pulling, buttons power, remove the battery, etc.)

  The afflicted system has a CD/DVD drive work?

  You have a true bootable XP installation CD (it is not the same as any recovery CD provided with your system)?

  Fill in the blank: my system was working fine until this happened: _.

  If the system works, what do you think might have changed since the last time it did not work properly?

  If you have no XP bootable media (or aren't sure you have) create a bootable XP Recovery CD of Console and do not forget.

  This is not the same as recovery disks that may have come to a store to purchase the system.

  You can make a bootable Recovery Console CD by downloading an ISO file and burn it to a CD.

  The ISO bootable image file you need to download is called:

  xp_rec_con. ISO

  Download the ISO from here:

  http://www.mediafire.com/?ueyyzfymmig

  Use a new CD and this simple and free program to burn your ISO file and create your bootable CD:

  http://www.ImgBurn.com/

  Here are some instructions for ImgBurn:

  http://Forum.ImgBurn.com/index.php?showtopic=61

  It would be a good idea to test your bootable CD on a computer running.

  You may need to adjust the computer BIOS settings to use the CD-ROM drive as the first device to boot instead of the hard drive.  These adjustments are made before Windows tries to load.  If you miss it, you will need to restart the system again.

  When you start on the CD, follow the instructions:

  Press any key to boot from CD...

  Installing Windows... going to pronounce.

  Press 'R' to enter the Recovery Console.

  Select the installation that you want to access (usually 1: C:\WINDOWS)

  You may be asked to enter the password (usually empty).

  You should be in the folder C:\WINDOWS.  It's the same as the

  C:\Windows folder that you see in Solution Explorer.

  The Recovery Console allows base as file commands: copy, rename, replace, delete, chkdsk, fixboot, fixmbr, cd, etc.

  For a list of the commands in the Recovery Console, type help at the prompt of commands or read on here XP Recovery Console:

  http://www.Microsoft.com/resources/documentation/Windows/XP/all/proddocs/en-us/recovery_console_cmds.mspx?mfr=true

  A good idea before you start things must first verify the integrity of your file system by using the chkdsk command.

  In the command prompt window, run the chkdsk command on the drive where Windows is installed to try to fix any problems on the afflicted player.

  Running chkdsk is fine, even if he finds no problem.  It won't hurt anything to run it.

  Assuming your boot drive is C, run the following command:

  CHKDSK C: /r

  Let chkdsk finish to correct the problems, he could find.

  It may take a long time for chkdsk complete or they seem to be "stuck".  Be patient.  If the HARD drive led blinks always, chkdsk is something.  Keep an eye on the amount of the percentage to be sure that it is still making progress.  It may even seem to go back sometime.

  You must run chkdsk/r again until it finds no error to correct.

  Remove the CD, and then type "exit" to exit the RC and restart the computer.

  You have not to set the BIOS to boot the disk HARD since the CD won't be.

  Do, or do not. There is no test.

  I decided to implement the points for a new puppy instead of a pony!

• SE error message: "the registry cannot load the hive (file) \systemroot\system32\config\software"when try to start on the original copy of Windows XP. "

  Original title: you're smarter then me. Help, please

  My windows xP home edition has crashed on my HP Pavilion a620n. Initially, I was able to get by using the original cd of the publishing house. Then it crashed again. Rebooted and pressed F8 and typed in my administrator id. This time, a cam of the screen saying that it was an ID of invaled. Re-checkeded my Id and it was OK. Put in my cd original and installed on a different partition. Problem is that I forgot to do a dual boot. Now I have two sessions of windows xp on the same partition. Am able to switch between them, but really need the original. When I click on the origianl happens with the registry cannot load the hive (file) \systemroot\system32\config\software.

  Is it possible to fix this?

  Thanks, it was a great help

• I have Canon Powershot G3X and cannot load the raw files in PSE13. Is a patch available?

  I have a Canon PowerShot G3X and cannot load the raw files in PSE13. A fix is available for this unit yet?

  Hi William,.

  Canon Powershot G3X supported by Camera raw version 9.1.1 and the latest camera 9.1 available with PSE 13.

  Devices supported by Camera Raw

  In the meantime, you can use the 9.1.1 DNG Converter to convert your raw images to DNG and then use it with PES 13.

  Windows

  Adobe - Adobe Camera Raw and DNG Converter: for Windows: Adobe DNG Converter 9.1.1

  Mac

  Adobe - Adobe Camera Raw and DNG Converter: for Macintosh: Adobe DNG Converter 9.1.1

  Let us know if it helps.

  ~ Mohit

• LoadFile() cannot load the local file?

  My program works OK in Director, also OK on the web, but can't work on local. It is said after post like Shockwave and HTML file when the Director runs the HTML code automatically, the DCR in HTML file works fail. I am looking for reason, find, this is because one sentence of the program:
  Member ("World"). LoadFile ("myModel.W3D", true, true)
  
  In Director, it works. myModel.W3D is 'file:///D:/MyDirectoty/myModel.W3D '. On the Web, that's OK too. At this time, myMode.W3D is actually "" http://www.myWebSite.com/MyProgramDirectory/myModel.W3D ". " But if I open the HTML published, the loadfile() cannot work. Why?
  
  It is because of security reasons, MacroMeadia let loadFile() cannot load the local file or there is a mistake in my program? How can I let my program works locally?
  

  Quote:
  Posted by: WrongAgain
  It is because of security reasons, MacroMeadia let loadFile() cannot load the local file or there is a mistake in my program? How can I let my program works locally?

  Bingo-test - this is a safety feature to prevent the shockwave files accessing your file system.
  You can disable this security feature by placing your project published in the folder called «DSWMedia» shockwave

  -Ben

• Registry cannot load the HIVE file; Need to fix WITHOUT the Recovery Console, computer will not play my Windows recovery disk.

  I need to fix my computer, I got the blue screen of death with the following error message. Registry cannot load the file \systemRoot\system32\config\SOFTWARE "HIVE".

  I read all the forums on how to solve this problem. I tried all the means which have been enumerated. None have worked so far because I can't get my CD player to load to run my Windows XP Pro disc to start the repair.

  Is there a way to fix this without the disc. I can't the computer after Windows XP display until he went blue. It's a computer original systemax, but I have since rebuilt it me with the new motherboard, hard disk, cdrom, dvdrom, ram, fans, cpu, etc... I just got a new monitor and hung up and blue screen of death appeared after that I turned the computer back on. I tried to fix this for 4 days now. Someone please HELP me.

  I got it fixed. THANK YOU SO MUCH for all your help!

• Error codes Vista 65535 and 0x8000fff when you try to load all the files, folders or applications

  I get these two error codes 65535 and 0x8000ff, I'm running Vista 32 bit, with only 1 GB of Ram and use a memory stick as a RAM boost option. System starts as usual, I can connect to the Web, but don't load all files, folders and applications. I have icons on the desktop, but like I said nothing loads. have you tried Live One Care safety scanner, downloads, but used to run, just get the codes above, no matter what I try. In desperation I tried a complete reinstall, still did not work and can not find the productkey.

  Thanks for the reply, we, ve decided that the hard drive is shot to pieces, and will install and old windows xp disc i've got. to solve the problem.

• load the PDF file inside the application (Android and Ipad)

  You want to open the PDF file inside the application. I try this code, his work in the PC but when I publish, in the form of APK file it does not work in my android device

  package {}

  to import flash.display.SimpleButton;

  import flash.events.MouseEvent;

  import flash.events.Event;

  import flash.html.HTMLLoader;

  import flash.net.URLRequest;

  public class bpdf extends SimpleButton {}

  public void bpdf() {}

  the constructor code

  this.addEventListener (MouseEvent.MOUSE_DOWN, downF);

  }

  private void downF(e:Event):void {}

  var htm:HTMLLoader = new HTMLLoader();

  htm. Load (new URLRequest ("test.pdf"));

  htm. Width = 200;

  htm. Height = 300;

  htm.x = 50;

  htm.y = 20;

  this.parent.addChild (htm);

  Create a close button for htm and Add (for this.parent) and its listener here

  }

  function onCloseEvent(e:Event) {}

  If (!.) HTMLLoader.isSupported) {}

  This.Alpha =. 1;

  }

  }

  }

  }

  

  

  use:

  import flash.media.StageWebView;

  import flash.geom.Rectangle;

  import flash.desktop.NativeApplication;

  import flash.events.MouseEvent;

  import flash.filesystem.File;

  swv var: StageWebView = new StageWebView();

  swv.viewPort = new Rectangle (0, 0, 500, 250); 500px width, height 450px

  SWV.stage = this.stage; step StageWebView document class

  var templateFile:File = File.applicationDirectory.resolvePath ("test.pdf");

  var workingFile:File = File.createTempFile ();

  templateFile.copyTo (workingFile, true);

  try {}

  swv.loadURL (workingFile.url);

  } catch (error) {}

  trace (e);

  }

• Loading (without rules file) crashes on EAS on the loading data in the exported file.

  I'm doing a load of data in a database if a file I exported previously and data loading crashes just after taking in the text file. It hangs where it says "press ESC or cancel button to complete the current operation. It is a very small text file that am loading data from. I have to kill the ESSSVR process for this particular application back the EAS to perform other tasks. Am able to do any other tasks very well. Also on our Prod environment we do not have this problem and can't seem to load the data through very well exported text files. Has anyone seen this behavior before?
  
  Thank you
  Ted.
  
  Published by: Teddd on March 4, 2013 08:52

  This announcement so it would be beneficial to others on 11.1.1.4 with essbase on RHEL 5 server. The answer to the question is in this Doc ID 1531236.1 knowledge of Oracle database. Apparently, it shows only on RHEL 5 and glibc is updated glibc - 2.5 - 107 of glibc - 2.5 - 81. The solution is to donwgrade the glibc 2.8 - 81. Please refer to this doc 1531236.1 if any of you have a similar problem.

  Published by: Teddd on March 14, 2013 11:38

• 3.5 AIR cannot load SWF graphics and app: folder "Application areas don't are not supported.

  "Error #3747: several areas of application are not supported on this operating system." appears and breaks my app when I'm trying to do something as simple as load a URL to use a graph to the File.applicationDirectory on iOS on AIR 3.5. I'm just trying to load graphics files included in my application.

  I don't know why it happens on "Several application areas." I'm not trying to do the fancy stuff, and exactly the same thing worked on AIR 3.4 and below.

  What is this error and how to fix it? No information appears on this topic in search engine result.

  Read notes of version 3.5 of AIR, there is how you should set the loaderContext in order to make it work.