Cannot print out of yellow ink

I am only the yellow ink and cannot print.  I have change to black with print on computer, but pop up options comes on off printer ink yellow mention.  How can I change the settings so I do not use color cartridges at all.  I have all in one, HP officejet pro 8500.

posterchild says:

I have a HP Officejet Pro L7555 with a similar problem, only it still says: I'm yellow ink after replaced without a cartridge HP yellow/black.  It won't let me scan or not while it is not yellow.

Black/Yellow printheads were replaced, it sounds like you had a low yellow cartridge that has been emptied by the maintenance required for a new printhead.  You will need to replace the power supply in yellow ink as shown here.

Tags: HP Printers

Similar Questions

  • HP all-in-one 8620: HP all in a single 8620 - will not print black because yellow ink so you are done?

    What nonsense, the here!

    my printer refuses to print black and white, pages saying that the yellow ink is finished?

    only if I buy a wet ink yellow it will print.

    Isn't this black mail? What does take to print?

    I did print it in black, etc, but still it prints no and gives a banner saying yellow ink purchase

    The standard yellow ink is available from HP here.  You can also consider the Multipack colourful three - if yellow is probably exhausted the other colors are not far behind.

    With regard to the requirement to have the ink color when you want to only print in black.

    HP and other printer manufacturers have technology another printer for different needs.  For ink jet printers:

    • Some have integrated into the ink cartridges print heads.  These printers can print generally with one or more of the colors completely empty, or even with color or black cartridges (but not both) removed. Deskjet 6980 series is an example, or for an all-in-one, see the 8040 a Officejet.
    • Other printers have separate replaceable printheads and inks.  An example would be the printer Officejet Pro 8620.  In these printers print head can be replaced if they are damaged by running the printhead with colors off.  Some of these printers allow printing with a color, the other will not.  If the printer is run without ink in one or several colours, the printer may be damaged, but the user may be able to recover without having to send the printer for the service by replacing the (expensive) print head.
    • Other printers have permanent print heads.  To run only those without little ink in all colours would risk causing damage to the print head because of clogs, air ingested in the printhead or grilled printhead resistances of shooting. The Officejet 6700 is an example of this type of printer. For printers with fixed print heads that could require the service to get the printer to print properly again when the ink is finally replaced.

    The document described here how the ink is used.  The document is written for inkjet printers HP the same principles apply to printers inkjet from other manufacturers.

    If you are ever printing a monochrome laser printer in color would probably be a better choice.  If you occasionally print color but especially black a HPI printer as those in the first category above can be a good choice.

  • Cannot print black or yellow on my hp 5520

    I have problems printing black and yellow of my Photosmart HP 5520. I ran head clean process repeatedly wait between cleanings and it still does not print. Black print cartridge is brand new and yellow is half full. I've been on the link which when black and other color does not print and still no luck. Any suggestions on what to do next would be greatly appreciated.

    Hi Octaboze,

    I sent a private message on the Forum, please go to your userpage to the right of your username, you will see your Inbox.

    Thank you

  • Office Pro 8000: Cannot Print/Out of ink error even after installing new cartridge.

    When I tried to use my printer a few days ago, I received an error message "can't Print Can: ink" on the magenta cartridge.  I had used the printer a few days before and had not received a low ink warning.  It seemed suspicious to me that I would have received an empty cartridge error message without having previously received a low cartridge warning.  The cartridges yellow and cyan read 70% complete - all 3 were original cartridges.

    I bought a new cartridge 940XL magenta and installed according to the instructions.  Now, I get a message that the new 940XL cartridge is empty.  I can shake the old cartridge 940 and hear liquid inside.  Obviously, the new cartridge is also complete.  I tried to electric bike, reinstall the software, etc., without change of status.  If I swap back between the 940 old and new cartridge 940XL, they are correctly identified by type on my screen as the 940 or 940XL.  Because of the way the problem is presented, I don't think it is a cartridge problem.

    Of course, problem first awaken on May 8, and my warranty expired on 26 April.  Any suggestions?

    I solved my problem, what was obviously a lack of factory Assembly.  I looked inside my printer with a flashlight in the area where the ink cartridges are installed and found sprayed inside the printer magenta ink.  I disassembled the printer and found that the magenta line had been damaged during installation.  There are four tubes of ink that out by behind the ink cartridges, can do a U turn back toward the front of the printer.  Just after the bend, they do an another elbow top neighborhoods.  It is at this point that I found the damaged magenta line, directly above a screw on the right side of the housing of the ink cartridge.  The lines are in a very narrow passage and are held in place by several guards, moulded plastic.  It seems that the lines have been in place in the guardians, then the screws inserted from the top.  As I said, there is a tight passage, and it would be very easy to damage the line of ink right here if the lines have not been carefully selected to insert the screws when mounting.

    To solve the problem, I removed about 1/4 inch line damaged magenta ink.  I cut the line with a sharp razor, carefully to avoid collapsing the line or causing burrs to the hose.  I then placed approximately 3/4 "heat self-sealing tube on one end of the line of ink heat shrink.  Then I connected to the line with a small piece of plastic tube rigid of the handle with a swab of cotton, which was a perfect fit and comfortable on the line of ink.  Making sure not to cut the tube of ink or cause other damage, gently twisted the line of ink back until the ends have butted up inside the splice of cotton swab.  I then positioned the shrink tube over splice and it shrunk with a hair dryer.  Heat shrink tube, I used a hot melt glue applied to the Interior, which has helped more away making a watertight splice.  Again, it is not a lot of space, so the splice should remain small.

    I reassembled the printer, reinstalled ink cartridges and powered by the printer.  After the normal, long time running, I printed full color sheets and everything was fine.  Already that I had installed the cartridge magenta watch now that it is complete, and the remaining cartridges also read the levels they had before disassembly.

  • Model of HP Pavilion p7-1240: Office Deskjet 8615 Pro cannot print out web

    I can't print anything on the web, he wantes me to everything save.

    Linda

    Hello

    You can use Google Chrome browser?

    Google chrome opens the print dialog box, and then press the button change.
    Select your printer from the list instead of the default save as PDF option and try to print again.

    Shlomi

  • Unable to print black and white with no yellow ink L7590

    I ran more ink at the weekend and got a new black ink cartridge. Unfortunately, I did not notice that I was also out of yellow ink. I desperately need to print regular black text, but the printer refuses because he is more yellow ink! I don't want print Yellow. Is it possible to disable this error message for a HP OfficeJet Pro L7590?

    Thank you.

    Nevermind, I figured it. If you set the printer on the mode of manufacture, it ignores the ink levels. Sorted.

  • new yellow ink cartridge (564) do not correctly print Photosmart HP 7510 e-all-in-one

    My Hp Photosmart 7510 e - all - in - one... I replaced the yellow cartridge XL 564 and I am getting yellow streaks... when printing a report, yellow is barely noticeable, with black stripes.

    Is this a faulty new cartridge?  Help, please!

    Carol

    DUH!   A senior moment here... I pulled out the yellow ink cartridge replaced by another new... at that moment, I realized the orange tab 'pull' was still attached.   Once I got his shot and re - insert the cartridge, it was fixed!

  • can not have only black when printing black but not yellow ink

    HP photosmart D7260 uses.  having run out of yellow ink.  only need to print in black now.  By selecting only black AM but the screen says I can't print at all, unless I have reconstitute the yellow ink.

    any solution short of buy yellow ink?

    The short answer for this printer: Yes.  For the Details of how the ink is used, see here.

  • printer says no ink after I change cartridge cannot print

    I have a HP Officejet Pro printer.  I ran out of ink and replace the cartridge but still cannot print.  The message is always replace the ink cartridge.

    Contact HP support, of course.

  • HP OfficeJet Pro 8000 Wireless: Can I get some help here? Yellow ink will not print - HP OfficeJet Pro 8000 Wireless

    No matter what I do, ink yellow does not print, or stops at halfway printing on the page. I use genuine HP cartridges. There is a lot of ink - in fact, I just installed a new cartridge in the case where a previous (almost complete) was defective. No change. The pipe is not pinched. I flashed the firmware more recent and installed all drivers and utilities updated. I have cleaned the print heads over and over again and even took and cleaned according to the instructions.

    I think it was a sign that the printer is worn EXCEPT - just a few months ago, magenta and black stopped printing. These are the opposite printheads. When I uninstalled every bit of HP software I could find, the printer back to normal!

    The only thing I did not - it is the HP Toolbox argues that it is impossible to establish two-way communication with the printer. The patches for this involve get under the desk to play with the power cord and USB cable (even if it is a wireless printer), and my arthritic knees that make a very delicate operation. Two-way communication IS enabled.

    I'm about to start crying. I fought with this market a week, when the yellow all of a sudden went - once again, * most * of the time, but sometimes it prints to maybe an inch of the image before disappearing. Help!

    Hi @Echo2,

    Thanks for joining the Forums of HP Support for a solution to your printing problem.

    I understand that you use a HP Officejet Pro 8000 printer with a Windows 7 computer and all of a sudden is not printing yellow ink. I would like to help with that.

    Here is a document of support for the print quality problems - Troubleshooting print quality problems.

    Please let me know if that solves the problem, or if you need assistance.

  • Photosmart 7520: hp photosmart 7520 yellow ink cartridge will not in (pop out of space)

    I tried to install two different new HP 564 XL yellow ink cartridge in my Photosmart 7520. They arise constantly from their slots. I managed with the magenta cartridge that is similar, but the yolks do not remain in place. What is the solution?

    Hi Rebmark, I did some research and found a troubleshooting page that describes some steps that might solve this problem.

    http://support.HP.com/us-en/product/HP-Photosmart-7520-e-all-in-one-printer-series/5199461/document/c02944025

    Step #9 may be the answer you're looking for. When the ink cartridges is not properly connected, it can help try gently bending the cartridge tab try to avoid to bend this tab over a half inch, as it could damage the cartridge.

    I hope this helps, but let me know if you're still having problems!

  • OfficeJet Pro X476dn: HP OJPro x 476 Ran out of black ink. To print the text in blue

    I have items/orders/faxes, I need to print.  I'm completely out of black ink.  Can I turn on the unit by default blue print?

    Hello

    The printer requires any ink cartridge and once any cartridge is exhausted (Out of Ink) you can print is no longer and the cartridge needs to be replaced to resume printing.

    As reference, see the following article:

    http://h20565.www2.HP.com/hpsc/doc/public/display?sp4ts.Oid=5276617&docid=emr_na-c03629143&docLocale=en_US

    Shlomi

  • Printer cannot print black, even with new ink

    Original title: cannot print in black

    I cannot print black on my printer.  I changed printers, ink cartridges and tried printing in different programs such as Word, wordpad and Excel.  Other black print colors just not.  Can someone tell me what is the problem?

    When you installed the printer cartridge, did you remove the protective sticker on the cartridge? Sometimes people forget to remove this and install the cartridge.

    You can also run the troubleshooting of the printer.

    Open the printer Troubleshooter

    Open the printer Troubleshooter by clicking the Start button, then Control Panel. In the search box, type troubleshooting, and then click Troubleshooting. Under hardware and sound, click on use printer.

    For more information, visit the below mentioned link:

    http://Windows.Microsoft.com/en-us/Windows7/open-the-printer-Troubleshooter

    Printer problems: http://blogs.technet.com/b/markrussinovich/archive/2010/04/12/3324570.aspx

    Run the printer problems to: http://support.microsoft.com/gp/printing_problems?entrypoint=WHHT

    You can see the below mentioned links.

    http://Windows.Microsoft.com/en-us/Windows7/install-a-printer

    http://Windows.Microsoft.com/en-us/Windows7/find-and-install-printer-drivers

    http://Windows.Microsoft.com/en-us/Windows7/change-your-default-printer

    http://Windows.Microsoft.com/en-us/Windows7/printing-to-the-correct-printer

  • HP Envy 5530: Yellow ink not print

    Yellow Ink stopped printing with the Tricolor cartridge; replaced by the new HP cartridge and not yet. Also tricolour ink not detected.

    Tried all the steps HP support, including the persistent page terminals on the cartridge and to the holder. Also reinstalled driver. No change.

    Is this a hardware problem? The printer is only 6 months old and so under warranty, but I buy an Epson if it is!

    All ideas welcome

    Thank you

    6 months and under warranty. Call HP for replacement.

  • HP Deskjet Ink Advantage 1515: Printer HP Deskjet Ink Advantage 1515 cannot print size A4

    Dear HP,

    I just bought printer HP Deskjet Ink Advantage 1515 this morning. After arived in the House, I set up the printer much. and I'm trying to print a photo in photo gloss paper A4 180 gr. I put the picture full size A4. but when I print it, the result makes me disappointed. It cannot print to A4 size. isn't that reach the size of the letter. my picture cut at the end of the book.

    I read the specs of the printer before buy you. It is said that the printer can print A4 size. but they do not mention on a Cup at the end of the book.

    My question is:

    • what I can do about the problem? (I tried the regional and language settings, but it does not work)
    • is this hardware problem or a software problem?
    • Can I get my warranty to be replaced by a new and fixed? How?

    I hope that there is solution. help me with that.

    Thank you

    Hello

    The technical specifications list the print margins, the printer may not exceed the margins you can find listed in the paper handling > print margins:

    http://support.HP.com/us-en/product/HP-DeskJet-ink-advantage-1510-all-in-one-printer-series/5285089/model/5285090/document/c03775352/

    As you can see below in the section of handling paper, borderless printing is not supported for the printer:

    http://WWW8.HP.com/emea_middle_east/en/products/printers/product-detail.html?OID=5385210&JumpID=oc_r1002_emea_middle_easten_c-001_r0001#! tab = specifications

    This is not a defect, these are the limits of the printer that you can find listed by its specifications.

    Shlomi

Maybe you are looking for

  • Why I do not receive my incoming mails when I click on new emails and my mailbox is NOT full!

    January 1, 2015 I've never had this problem before and I suddenly said "my Inbox is full and cannot hold messages more" this happened for several days and I cleaned my deleted and could help many special registered mail in other folders, thinking tha

  • View a large list system

    Hello My "Downloads" folder displays the files in a list format; I prefer this view. Is it possible to ensure that this view is the default system-wide? Currently, I have to adjust the view to 'List' for each different section in "Finder." Thanks in

  • Satellite L750 - card problem Flash after Windows 8.1 update

    I looked at other threads in the forum, but each of them suggests to try drivers (function key) for other laptops, the only way to make it work now is to uninstall the driver function key; but the problem is the wifi and Bluetooth is still on after l

  • Name resource RIO issue

    Hello I have a request to change the name of RIO resource (not the alias), I think that it is auto-generated and not something that I can put. If I'm wrong, someone could show me how and if I'm wrong can someone direct me to the documentation? Thanks

  • my CPU usage was 100% for more than 2 hours windows 7 x 64

    my windows 7, x 64 went to 100% cpu for at least 2 hours..., usage with 1.6 GB of 4,094., it is running 104 process all can give me a hint? TXS Dan