Cannot start after upgrading Windows 10 Dolby Home Theater

Similar Questions

• Windows 10 Dolby Home Theater V4 does not

  On my Lenovo Edge 15 (BestBuy exclusive model), I've recently upgraded to Windows 10 and found that the Dolby Home Theater V4 software does not work. I tried to uninstall and reinstall the drivers and software and still cannot program to work. The program opens and displays options, but Equalizer does not move (as it was on Windows 8.1) and it doesn't have a difference in the audio output.

  All of this worked before my Windows 10 transition. The audio quality is very thin and hard to hear without this software, I hope someone has a solution. Thank you very much for your help!

  Nice day.

  Please see Section 3 - limits of Application, from: https://support.lenovo.com/us/en/documents/ht103611
  Dolby Home Theater is not supported / not functional on Windows 10, for compatibility reasons.
  The official recommendation is to first uninstall it before upgrading to Windows 10.

  Hope this helps to clarify.
  Kind regards.

• OfficeJet 8500: Cannot parse after upgrade Windows 10

  After the upgrade to 64-bit Windows 10 Pro, I can't scan my OfficeJet 8500 909n.  I get this message:

  "The analysis cannot because another program or computer using the networked HP imaging device. Try again later. »

  I have a / re installed HP Solution Center 5 times.  I restarted routers.  I'm power cycling my PC and the printer several times.

  I can print to this printer from three PC.  I can't get the scan to work as before.  This has been driving me crazy for more than 5 hours.  I'm honestly ready to go back to Windows 7.  The printer is connected via the cable network.

  Can someone please help?

  Thank you.

  Kind regards

  Jim

  Hello

  Thanks for the comments, you can try this alternative software:

  HP extended Scan
  
  FTP://FTP.HP.com/pub/scanners/HPScanExt/HPScanExt.msi
  
  Once it has downloaded and installed, go to start > all programs > HP > HP Scan extended > Run "HP Scan extended.
  
  Let us know if it works.

• OfficeJet 6500 E709n: Cannot print after upgrading Windows 10

  Cannot print. "Doctor print" said there is a software problem.

  Uninstalled the drivers and reinstalled the software complete... twice.

  Capable of printing in color "internal" wireless test page but cannot print a doc and it does not show in the Panel "see what's printing.

  Uninstalled all printers if none showed, in the Panel. When the software has been reinstalled, it showed two Officejet 6500 s on the control panel.

  I tried the post install 'Print sample' with each check printer default and no work.

  Seems that the problem started when I "upgraded" to the new Windows 10.

  Kili2 wrote:
  

  Cannot print. "Doctor print" said there is a software problem.

  Uninstalled the drivers and reinstalled the software complete... twice.

  Hi Kili2,
  
  Try to install your printer via "Open network" - via the window icon or desktop to explore - and choose 'Add devices and printers' (you may need to click the arrow next to the question mark for the top menu show).
  Let the wizard to search for awhile, selcect your printing device, and click 'next'.

  

  After you follow these steps, search for the new installed printer (the name is shown in network for printer and scanner) in "Printers and devices" in the control panel.
  Use this printer as the default printer and you should be able to print over the network cable or wireless.

• HP Pavilion does not start after upgrading Windows 10

  (Sorry for my bad English)
  Last night I started to update my HP Pavilion Windows 8.1 to 10, but I have a problem, because today, in the morning, the update was 99%, and it ended, just after I have shut down the computer and is going to school and when I got home, I turned on my HP and the problem was that the HP logo appeared and he began to load , but he didn't only show anything else than that, so I thought I'd let load after 3 hours, it was still loading and it was reseting every 5 minutes and now I just can't not try windows 10. Help?

  Hi there @lmao1,

  Thank you for joining the Forums HP's Support and welcome! It is a great place to ask questions, find solutions and get help from others in the community! I read your post on the Forums of HP Support. I wanted to join you and help! I understand that once you tried to upgrade to Windows 10, now stuck on the HP Logo at startup.

  If the computer hangs at the HP logo screen, try to clean the vents from the computer to the air and then restarting the laptop.

  Please note , remove all USB devices. Disconnect all devices of non-essential, as these can cause some problems.

  Have you tried a hard reset?

  Have you tried to Test for hardware failures?

  Are - that you receive error messages or error codes?

  You happen to see a blue "option ' screen at all? '"

  Follow these steps to remove and reinsert the memory modules for troubleshooting:

• Cannot start after installing windows 10 company first pro 2015

  Hello

  Need help with the Premiere Pro 2015. Today, I did the upgrade of Windows 10 Enterprise (64-bit). After that, it is not possible to start the first pro.

  Thank you for helping me.

  Hi Oliver,.

  Start a conversation with support here.

  Thank you
  Kevin

• Cannot connect after upgrade windows 7

  Hello

  just complete the upgrade to Windows 7 from Vista on my laptop A500 series.
  It finished installing fine shot when it restarts the login screen came with 'Administrator' and 'another user' clicked the button administrator and he said that the account has been disabled and to contact the administrator (that would be me!) and the other asked for a user name and password that I wouldn't have any idea.

  Tried my old account login and didn t work. As it is a custom installation, I n t understand why there would be an account already set up?

  Need help urgent as it is impossible to use my laptop atm!

  Hi Tims

  I'm really confused now. Last week I tested on my brand-new Satellite A500 - 157 (PSAM3E) upgrade.
  I've updated preinstalled Vista 32 and 64-bit, and both procedures went well upgrade and without some strange problems described in your ad.
  New install of Win7's fine also.

  Have you used DVDs from Toshiba or Microsoft upgrade?

• HP envy 4500: hp envy 4500 cannot print after upgrading Windows 10

  Does not work with windows 10. When the updated drivers will be available?

  I have downloaded and run EN4500_198.exe. Add a new printer via direct wireless.  I received the message that my printer has been installed. When I try to access the printer through the network, the printer is not found. When I do for the devices and printers, I see my printer with the following message: HPF734F1 (HP ENVY 4500 series) driver is not available.

  I can scan to my computer, just not printing. I'm lost.

  OK just figuredb out. had to remove the old printer definition Bundeskunsthalle windows 8.1. Once I did that, win dows 10 find the printer on the network and use it correctly.

  Thanks for all the help.

• G480 - cannot start Dolby Home Theater after upgrade Windows 10 for g480

  Does not start after upgrade to window 10 for my portable home dolby cinema g480. can anyone help? cannot find the driver on the Lenovo Web site

  Mod edit: System model added to the front of the subject line to improve visibility / clarity.

  Dear Sir

  Welcome to Lenovo Community

  There is no driver for windows 10 for your machine but let try 2 ways, all first try to install the windows 8.1 driver it may be helpful (see below):

  http://support.Lenovo.com/eg/en/products/laptops-and-netbooks/Lenovo-G-series-laptops/LENOVO-G480-No...

  or try the same 10 windows-compatible driver from the below link from driver identifier (when you open the link you will be asked your name & e-mail, you can use fake ones then next page choose non-commercial usage and then from the first link, hope this will work with you,

  http://www.driveridentifier.com/scan/download_file.php?URL=http%3A%2f%2Fcdgenp01.CSD.Toshiba.com%2fc...

  If its is not working so the best solution is to go back to the previous version of windows

  awaiting your response

  Good luck

• Laptop HP Pavilion G6: after upgrade windows 10 - cannot detect wireless network

  Hello

  I upgraded my computer windows 10 laptop and it cannot detect a network.   The network adapters that appear in the Device Manager - controller Realtek PCI FE and Qualcomm-Atheros 802.11 AR9485 wifi adapter but I can't see any network.   I tried to install several drivers for Atheros without success.   I went back to windows 8.1 and network drivers works, I have upgraded to windows 10 back and I can't connect to wireless networks. I tried to update the drivers without success, uninstall and reinstall without success, I have alos tried the solution published on the microsoft unsuccessfully Web site: https://support.microsoft.com/en-us/kb/3084164

  I get an error message saying "the system was unable to find the key to register specified or the value '. '" I didn't install any software VPN or another, is there a solution to my problem?

  Hi there @tikaro23,

  Thank you for visiting the Forums HP's Support and welcome! It is an excellent site to find answers and ask questions. I understand that you have a problem with your Wi - Fi on the laptop HP Pavilion G6. You mentioned that you can't detect a wireless network.

  I did some research and found a great document for you called HP PC - troubleshooting wireless network and Internet.

  What happened with you have attempted to use the resolution of the problems mentioned in the link you so much?

  Have you tried to restore the BIOS?

  Have you tried to connect directly to the Modem/Router?

  Have you tried to boot mode safe?

  You can maneuver in Mode safe without problem?

  In my research, I also found a Support Forum on the page called Microsoft Community after upgrading Windows 8.1 for Windows 10, no wireless networks are available.

  There is a post of RajithR. Read his message in its entirety. (I also provided it below.)

  

  You said you tried to uninstall the driver. Are - what you got to do it in the order shown below?

  • Uninstall the driver of network card in Device Manager,
  • Reboot the laptop twice,
  • Reinstall the driver.

  Please use the HP Support Assistant, it will help with the software and drivers on your system at the time of purchase or this update of need.

  I know you said you tried to update the driver also. Have you tried to do it in the Device Manager in the order given below?

  • In the Device Manager
  • Click the network adapters to expand
  • Right-click on the network adapter family
  • Select software update of the driver
  • Choose search for automatically updating driver software.
  • Once the installation is complete, restart your laptop.

  Please follow the troubleshooting steps above and the re-post with the results, information from the above questions and HP Pavilion G6 Notebook PC model number.

  Thank you!

• do not start cc2015 after upgrading Windows 10

  Do not start CC2015 after upgrading Windows 10!

  What can I do?

  A time CC2015 open and that thr program stop and closed.

  Can I read a text at the present time it is not possible.

  What can I do?

  Best regards

  Sandte

  Hi Brucgovn, thanks for the answer! Just sorted and came here to update the post.

  My method is similar, I just do the following:

  1. Go to C:\Program Files (x 86) \Adobe\Adobe Creative Cloud\CoreSyncExtension (this was the only file on the left, all others had been removed from the CreativeCloudCleaner use of the Adobe Creative Cloud cleaning tool to solve installation problems running
  2. I came across the problem trying to remove, so used Unlocker (Download Unlocker 1.9.2 - FileHippo.com) to unlock. Then deleted. It's explorer.exe using the process, which I think caused questions... the process is using the file
  3. Reinstalled and everything seems to work.

• Dolby Home Theater v4 for Windows 8?

  Hello

  I have an E420s, I had Windows 7 top and could use the Dolby Home Theater thing in speaker properties > Dolby, it was just power and 3 modes (music/movie/game), and I could notice a huge difference when it turn on and off when listening to music.

  After that I have upgraded to windows 8 it does simply not more.

  All Audio/Conxant drivers are updated.

  and when I tried to install drivers E420s Dolby v4 (but for win7, cuz theres no version win8) and got an error, something like:

  «The current version of the Dolby audio driver is 7.2.8000.14 and the software application expects that the version of the driver 7.2.7000.7.»

  Suggestions?

  e420sower,

  You encounter errors during startup until the metro screen or the Office of a start-up costs?

  We will try to uninstall the Conexant Driver, both Dolby Home Theater v4. Then, download the Conexant driver and install from the desktop. Once done, get you any result of the Dolby amplifier?

• computer does not start after the Windows XP logo window

  Windows xp home edition
  service pack 2
  Dell inspiron 1501

  1. computer does not start after the Windows XP logo window
  2 works well in safe mode, even connect to the external monitor
  3. I reinstalled xp many times, problem stil exist.

  All the answers?

  Hi dhanushm,

  1. What happens after the Windows logo screen?
  2. You receive an error message?
  3. You have security software installed on the computer?
  4. Have you performed an installation clean Windows XP and even after that this problem exists?

  Method 1

  As the computer starts up fine in safe mode there is a possibility that some third-party programs installed on the computer is the origin of the problem.

  I suggest that you configure the computer in a clean boot state and check if it helps.

  To help resolve the error and other messages, you can start Windows XP by using a minimal set of drivers and startup programs. This type of boot is known as a "clean boot". A clean boot helps eliminate software conflicts.

  See section to learn more about how to clean boot.

  How to configure Windows XP to start in a "clean boot" State

  http://support.Microsoft.com/kb/310353

  Reset the computer to start as usual

  When you are finished troubleshooting, follow these steps to reset the computer to start as usual:

  1. Click Start , and then click run.
  2. Type msconfig , and then click OK.
     The System Configuration utility dialog box appears.
  3. Click the general tab, click Normal Startup - load all device drivers and services , and then click OK.
  4. When you are prompted, click restart to restart the computer.

  Method 2

  If fails it above step can refer to the article below and try the steps mentioned, check if it helps.

  After the Windows Logo appears or after you log in to Windows, a Windows XP computer cannot display the wallpaper, a black screen or a blue screen

  http://support.Microsoft.com/kb/318027

• IDEAPAD Z580 - Dolby Home Theater v4 for 'Windows 8' 64-Bit

  Where can I get Dolby Home Theater v4 for Windows 8 64-bit?

  In the driver package...

  After unpacking... in the pilots appear is dolder for Dolby home v4 t.

• How much time after reinstalling window 7 32 Home Premium it take before that receive updates?

  * Original title: update Windows 7

  How long after reinstalling window 7 32 Home Premium does it take before that receive updates.

  Should be immediately the minute that an Internet connection is detected. I would advise that you install updates Windows Update batch well. There are about 300 post SP1 updates, more if you have reinstalled the version Windows 7 RTM.

  My recommendation would be to install updates in batches, these 5 at a time, exclude the hardware/driver updates. Avoid installing a set of updates for Microsoft Windows and Office at the same time. Also, try to install the first small updates. Avoid installing things like the .NET Framework and SQL Express updates.
  Whenever you install updates (it's a chore, but it guarantees a more reliable experience). Try to start the Microsoft Office updates for programs such as (Word, Excel, Outlook, PowerPoint).
  Another thing, try to download the updates, and then install them. When you are prompted to restart, disconnect from the Internet and restart your computer.
  To proceed with the installation of additional updates.
  If the continuous computer to become unresponsive, try the following:
  
  You can reset the Windows Update components by running the Fixit on this page.  But if there is malware present, she will continue to reset the connection to the update servers:
  How to reset the Windows Update components
  http://support.Microsoft.com/kb/971058
  Suggest you download and save the Fixit.  Then configure the system before the clean boot by running:
  How to troubleshoot a problem by performing a clean boot in Windows Vista/Windows 7
  http://support.Microsoft.com/kb/929135
  Once the Fixit has been downloaded and the system is started in the pure State, check that the native Windows Firewall is now on if a 3rd party firewall has been used previously.  Now run the Fixit and choose the default mode.  Restart once it's done and see if the system can be connected to the update servers.  If he can't, then rerun the Fixit and choose aggressive mode.  Turn it back on when he finished the race and updates.
  I suggest before you stop and install the updates, disconnect from the Internet, first.