Cannot use Winodws XP System Restore utility

I wonder if anyone can help. I can't get my laptop to restore as soon as possible. I have it and have used control points and manually restore points but it will not restore.

Don't stop of saying impossible to restore. No changes have been made.

Hello

Check it please this page http://www.theeldergeek.com/system_restore_not_functioning.htm

Good luck!

Tags: Toshiba

Similar Questions

  • Cannot set the restore point with the error "The Volume Shadow Copy service used by the system restore does not work."

    Cannot set the restore point with the error "The Volume Shadow Copy service used by the system restore does not work."  How can this be repaired?

    Hi rebick,.

    Try the troubleshooting steps presented by spirit X in this thread.

    Dena
    Microsoft Answers Support Engineer
    Visit our Microsoft answers feedback Forum and let us know what you think.

  • I'm unable to connect to the internet and I also can not use the WinXP system restore.

    No internet connection and I also can not use the WinXP system restore because it gives me an error at the 'end' which said: it cannot be restored to an earlier date.  I run AntiMalware bytes and StopZilla and erased all that they found.  Now I can't even connect to the internet.  When I go to the command prompt, it gives me an error contact the Support of MS that I know means I have a virus or a trojan that I should just get a time out?  My other PC on the same network is fine and connected.  The NETWORK card is fine, just does not know how to get rid of what it is, I have and to top it all impossible to connect to the internet to try all of the tools that can help.  Someone at - it ideas?

    The error you get at the end of the restoration of the system is typical of some anti-virus programs (Norton, especially) that interfere with the restoration of the system.  Try to start your computer in Mode safe (on several occasions, key to tap F8 while your computer starts) and run safe mode system restore.

    Additional information is necessary to treat your network problem.  Try to bring up a command prompt (start-> Run-> "cmd") or if it does not, try (start-> Run-> "command.com") and enter the command:
    ipconfig/all
    and after the info that appears in the State resulting.

    Also, check the logs of your system related errors (start-> Run-> "eventvwr.msc") and click on 'System' in the left column.

    HTH,
    JW

  • Cannot use the rollback system for non-system tablespace segment ' TEMP

    Hello world!

    I encountered this error: "cannot use the non-system"TEMP tablespace system rollback segment.

    So what I did to check the cancellation stuffs online.
    SQL> select tablespace_name,status from dba_tablespaces;

TABLESPACE_NAME                STATUS
------------------------------ ---------
SYSTEM                         ONLINE
UNDO                           ONLINE
SYSAUX                         ONLINE
TEMP                           ONLINE
LARGEDATA                      ONLINE
LARGEINDEXES                   ONLINE
MEDIUMDATA                     ONLINE
MEDIUMINDEXES                  ONLINE
SMALLDATA                      ONLINE
SMALLINDEXES                   ONLINE
XSMALLDATA                     ONLINE

TABLESPACE_NAME                STATUS
------------------------------ ---------
XSMALLINDEXES                  ONLINE
XXSMALLTABS                    ONLINE
USERS                          ONLINE
CONVTABLES                     ONLINE
UNDO_02                        ONLINE

16 rows selected.

SQL>  SELECT tablespace_name, sum((bytes/1024)/1024) free FROM DBA_FREE_SPACE gr
oup by tablespace_name;

TABLESPACE_NAME                      FREE
------------------------------ ----------
LARGEDATA                      18.3105469
SMALLDATA                        10.46875
SYSAUX                           106.5625
UNDO_02                            67.125
XXSMALLTABS                    13.0078125
CONVTABLES                     170.039063
MEDIUMDATA                             22
USERS                           37.265625
SYSTEM                             55.875
LARGEINDEXES                   30.5175781
XSMALLINDEXES                    17.34375

TABLESPACE_NAME                      FREE
------------------------------ ----------
UNDO                             546.9375
MEDIUMINDEXES                       33.25
SMALLINDEXES                    31.015625
XSMALLDATA                     23.6328125

15 rows selected.

SQL> select file#,status from v$datafile;

     FILE# STATUS
---------- -------
         1 SYSTEM
         2 ONLINE
         3 ONLINE
         4 ONLINE
         5 ONLINE
         6 ONLINE
         7 ONLINE
         8 ONLINE
         9 ONLINE
        10 ONLINE
        11 ONLINE

     FILE# STATUS
---------- -------
        12 ONLINE
        13 ONLINE
        14 ONLINE
        15 ONLINE

15 rows selected.

SQL> select segment_name, tablespace_name, initial_extent,status
  2  from dba_rollback_segs;

SEGMENT_NAME                   TABLESPACE_NAME                INITIAL_EXTENT
------------------------------ ------------------------------ --------------
STATUS
----------------
SYSTEM                         SYSTEM                                 102400
ONLINE

_SYSSMU1$                      UNDO                                   131072
OFFLINE

_SYSSMU2$                      UNDO                                   131072
OFFLINE


SEGMENT_NAME                   TABLESPACE_NAME                INITIAL_EXTENT
------------------------------ ------------------------------ --------------
STATUS
----------------
_SYSSMU3$                      UNDO                                   131072
OFFLINE

_SYSSMU4$                      UNDO                                   131072
OFFLINE

_SYSSMU5$                      UNDO                                   131072
OFFLINE


SEGMENT_NAME                   TABLESPACE_NAME                INITIAL_EXTENT
------------------------------ ------------------------------ --------------
STATUS
----------------
_SYSSMU6$                      UNDO                                   131072
OFFLINE

_SYSSMU7$                      UNDO                                   131072
OFFLINE

_SYSSMU8$                      UNDO                                   131072
OFFLINE


SEGMENT_NAME                   TABLESPACE_NAME                INITIAL_EXTENT
------------------------------ ------------------------------ --------------
STATUS
----------------
_SYSSMU9$                      UNDO                                   131072
OFFLINE

_SYSSMU10$                     UNDO                                   131072
OFFLINE

_SYSSMU11$                     UNDO_02                                131072
OFFLINE


SEGMENT_NAME                   TABLESPACE_NAME                INITIAL_EXTENT
------------------------------ ------------------------------ --------------
STATUS
----------------
_SYSSMU12$                     UNDO_02                                131072
OFFLINE

_SYSSMU13$                     UNDO_02                                131072
OFFLINE

_SYSSMU14$                     UNDO_02                                131072
OFFLINE


SEGMENT_NAME                   TABLESPACE_NAME                INITIAL_EXTENT
------------------------------ ------------------------------ --------------
STATUS
----------------
_SYSSMU15$                     UNDO_02                                131072
OFFLINE

_SYSSMU16$                     UNDO_02                                131072
OFFLINE

_SYSSMU17$                     UNDO_02                                131072
OFFLINE


SEGMENT_NAME                   TABLESPACE_NAME                INITIAL_EXTENT
------------------------------ ------------------------------ --------------
STATUS
----------------
_SYSSMU18$                     UNDO_02                                131072
OFFLINE

_SYSSMU19$                     UNDO_02                                131072
OFFLINE

_SYSSMU20$                     UNDO_02                                131072
OFFLINE


SEGMENT_NAME                   TABLESPACE_NAME                INITIAL_EXTENT
------------------------------ ------------------------------ --------------
STATUS
----------------
_SYSSMU21$                     UNDO_02                                131072
OFFLINE


22 rows selected.
    How do I bring them online?

    I tried this but did not work for me.
    SQL> alter rollback segment _SYSSMU1$ online;
alter rollback segment _SYSSMU1$ online
                       *
ERROR at line 1:
ORA-00911: invalid character


SQL> alter rollback segment '_SYSSMU1$' online;
alter rollback segment '_SYSSMU1$' online
                       *
ERROR at line 1:
ORA-02245: invalid ROLLBACK SEGMENT name


SQL> alter rollback segment _SYSSMU21$ online;
alter rollback segment _SYSSMU21$ online
                       *
ERROR at line 1:
ORA-00911: invalid character


SQL> alter rollback segment SYSSMU21$ online;
alter rollback segment SYSSMU21$ online
*
ERROR at line 1:
ORA-01534: rollback segment 'SYSSMU21$' doesn't exist


SQL> alter rollback segment '_SYSSMU21$' online;
alter rollback segment '_SYSSMU21$' online
                       *
ERROR at line 1:
ORA-02245: invalid ROLLBACK SEGMENT name


SQL> alter rollback segment "_SYSSMU21$" online;
alter rollback segment "_SYSSMU21$" online
*
ERROR at line 1:
ORA-30017: segment '_SYSSMU21$' is not supported in MANUAL Undo Management mode

SQL> ALTER SYSTEM SET UNDO_MANAGEMENT=AUTO SCOPE=SPFILE;

System altered.
    Must I bring each segment online separately? Please guide me.
    Nith

    Published by: user645399 on February 23, 2011 14:52

    user645399 wrote:
    Shouldn't have 2 undo tablespace?

    Is that what you mean?

    Yes, above statements completely wrong.
    If you use single instance database (non-RAC) and then use an undo tablespace

  • ORA-01552: cannot use no tablespace system rollback segment

    Hello

    When I try to create a table, I got the following error message.

    ORA-01552: cannot use tablespace no system "USER" system rollback segment

    Select nom_segment, nom_tablespace, initial_extent, status
    of dba_rollback_segs;

    NOM_SEGMENT NOM_TABLESPACE INITIAL_EXTENT STATUS
    ------------------------------ ------------------------------ ---------------------- ----------------
    114688 ONLINE SYSTEM
    _SYSSMU1$ UNDOTBS1 131072 OFFLINE
    _SYSSMU2$ UNDOTBS1 131072 OFFLINE
    _SYSSMU3$ UNDOTBS1 131072 OFFLINE
    _SYSSMU4$ UNDOTBS1 131072 OFFLINE
    _SYSSMU5$ UNDOTBS1 131072 OFFLINE
    _SYSSMU6$ UNDOTBS1 131072 OFFLINE
    _SYSSMU7$ UNDOTBS1 131072 OFFLINE
    _SYSSMU8$ UNDOTBS1 131072 OFFLINE
    _SYSSMU9$ UNDOTBS1 131072 OFFLINE
    _SYSSMU10$ UNDOTBS1 131072 OFFLINE

    11 selected lines

    One advises will be useful, thanks

    Make sure that the return parameters in your database instance.

    SEE THE PARAMETER UNDO

    You should have UNDO_MANAGEMENT = "AUTO" and UNDO_TABLESPACE = 'UNDOTBS1.

    Hemant K Collette

  • System Restore utility cannot restore to restore point

    I am under Windows XP SP 3 and have a disconcerting problem.  (SR) system restore will not restore my system to an earlier time.  SR is activated and creates automatic restore points every day, and I can also create points of restoration on request.  But when I actually try to restore the system to one of these points, the RS utility is unable to do with the useless message that it was impossible to restore my PC to an earlier time and no changes to my PC.  I suspect that some interviews I've done recently is the culprit.  I downloaded and installed a maintenance of Uniblue software, including Registry Booster and Rescue Disk.  The first is an optimizer registry/cleaner and my PC doesn't seem to work faster as well.  The latter is a disk defragmentation tool, and when it runs, it displays the names of files and folders, as it reorganizes.  I noticed it was the defrag the System Volume Information folder, including RPxxxx files, which of course contain restore point information.  (It is my understanding that the System Volume Information folder is not available for normal Windows interface and how this tool is there to do for maintenance is a mystery to me.)  But since I have used these two tools, the RS utility has not completed a restoration successfully.  It doesn't matter if I try to restore to a prior restore point or after the time when the interview was made.  I can create a restore point and immediately try to restore it with negative results.  I uninstalled the software Uniblue, but that did not fix my problem.  How can I overcome this severe limitation and recover the critical capacity of system restore?  Thank you very much...

    I've never seen Vista for more than a few minutes, but it is a fairly common problem with XP.  It is usually not a problem to Microsoft at all.

    (You are in a group XP... Vista forums are here: http://social.answers.microsoft.com/Forums/en-US/category/windowsvista)

    Here is my copy/paste standard for an XP system with the problem described by capehaze13 above.  Maybe it will give you some ideas or to reflect:

    Some tools AV 'protect' your system so that they will not allow a restore of the system work properly.

    For example, if you use Norton/Symantec products, you will see a message like this:

    Restoration incomplete. Your computer cannot be restored...

    It is also a popular Symantec problem (well, I'll be polite and call an "undocumented feature"...), they wrote an article about it:

    http://Service1.Symantec.com/support/sharedtech.nsf/pfdocs/2005113009323013

    Depending on what you use for malware protection, you will maybe disable the product temporarily, make the system restore and then turn on the product.

    Sometimes, you will need boot mode safe, and while that your protection programs do not, then do the system restore.  Microsoft refers to this in some of their writings too and it works sometimes favorably (do the system restore in Mode safe that is).

    Give these ideas some consideration if they apply to you.

    Sometimes malicious will afflict your system restore to prevent you to find and remove malware.  It would much rather you trick into thinking that you need to repair or reinstall your XP when it is not necessary.

    No matter what you use, I do so and then only begin to solve any problems:

    Download, install, update and do a full scan with these free malware detection programs can solve any problems:

    Malwarebytes (MMFA): http://malwarebytes.org/

    SUPERAntiSpyware: (SAS): http://www.superantispyware.com/

    It can be uninstalled later if you wish.

    The scans by operating clean, reboot, test and we can fix any other issues.

    Do not guess what the problem might be - understand and resolve it. I need YOUR voice and the points for helpful answers and propose responses. I'm saving for a pony!

  • Question about the use of XP system restore

    Hello

    Enjoy a few clarifying help on the system restore.

    If I have a pc with drive C and D and if I had to backup C drive the pc using the system image, and if I had to restore the pc using the system image, the image will overwrite D: drive, leaving only the C drive on the pc?

    Hope you understand what I mean here.

    Thanks in advance

    Richard

    Hello

    Thank you very much for taking the time to help. the system image is created by the windows backup utility. From what I read,.

    1. On the Advanced Boot Options menu, use the arrow keys to select repair your computer and press ENTER.

    2. Select a keyboard layout, and then click Next.

    3. Select a user name and type the password, and then click OK.

    4. In the System Recovery Options menu, click Windows complete PC Restore, and then follow the instructions.

    I do not know if you erase D drive from the pc...

    Richard

    This is the forum for Windows XP Windows Xp lacks a built-in drive cloning tool. For me it looks like you have Windows 7

  • I have the same problem. When I do a system restore, I get an error message. The service of shadow copy of Volume used by the system restore does not work. Error 0 x 81000202

    My security service center cannot be started too.

    Hello

    Malware scan

    malware stops normally you use the system restore protect themselves remove you

    Download update and scan with the free version of malwarebytes anti-malware

    http://www.Malwarebytes.org/MBAM.php

    You can also download and run rkill to stop the process of problem before you download and scan with malwarebytes

    http://www.bleepingcomputer.com/download/anti-virus/rkill

    If it does not remove the problem and or work correctly in normal mode do work above in safe mode with networking

    Windows Vista

    Using the F8 method:

    1. Restart your computer.
    2. When the computer starts, you will see your computer hardware are listed. When you see this information begins to tap theF8 key repeatedly until you are presented with theBoot Options Advanced Windows Vista.
    3. Select the Safe Mode with networking with the arrow keys.
    4. Then press enter on your keyboard to start mode without failure of Vista.
    5. To start Windows, you'll be a typical logon screen. Connect to your computer and Vista goes into safe mode.
    6. Do whatever tasks you need and when you are done, reboot to return to normal mode.
    7.  

    and try to do a restore mode safe

    Windows Vista

    Using the F8 method:

    1. Restart your computer.
    2. When the computer starts, you will see your computer hardware are listed. When you see this information begins to tap theF8 key repeatedly until you are presented with theBoot Options Advanced Windows Vista.
    3. Select the Safe Mode option with the arrow keys.
    4. Then press enter on your keyboard to start mode without failure of Vista.
    5. To start Windows, you'll be a typical logon screen. Connect to your computer and Vista goes into safe mode.
    6. Do whatever tasks you need and when you are done, reboot to return to normal mode.
    7.  

    and if using norton disable product anti-forgery protection

    http://Service1.Symantec.com/support/sharedtech.nsf/pfdocs/2005113009323013

  • used to open system restore reads error toggle one or more readers

    problems with the system running trying to run the system restore may depend on the restoration

    Hello

    1. don't you make changes to the computer until the problem occurred?

    I suggest you to try the steps below and check if it helps.

    Troubleshooting for problems when you try to use the System Restore tool in Windows XP: http://support.microsoft.com/kb/302796

    Hope this information is useful.

  • Satellite L 40 Vista Premium - cannot read the original system restore disk

    My satellite L40 was bought a year ago, and so far I never needed the system restore CD. But now I have a missing system file so I will try to re - install. But my computer will not read the CD, if I insert it before starting my computer or windows Vista.
    Is there a way I can download the CD to restore the system on the Internet?

    Hello

    No you can't download because that would hurt microsoft license stuff. I recommend you ask a partner in your country for replacement, if your machine is still under warranty.

    Please go here and find the service provider nearest to them for help.

    Welcome them

  • Cannot redownload trial after system restore

    I had downloaded CC as well as Photoshop, Illustrator and After Effects as trial versions, and very well without any problem, they launched. However, my computer went through a restoration of the system (at an earlier date) and now these programs are no longer on my computer. CC is always installed, and it keeps acting like it updates all three, but he throws any of them; and they appear as programs in my control panel (0 search results).

    I thought I could solve this problem with a simple redownload the site, but apparently he thinks I still have programs installed and refuses to do. No idea what I need to do? My trial is wasting away!

    I use this on a PC with Windows 8.

    Hi hmiller61615_,

    Run the Creative Cloud ( http://www.adobe.com/support/contact/cscleanertool.html ) cleaning tool to remove all/all CC products installed.

    Also delete Adobe Application Manager. Download the MAO from http://www.adobe.com/support/downloads/detail.jsp?ftpID=4773

    And then install the product.

  • I deleted a program by mistake and now when I try to do a system restore, I get a message that it was defective and that you cannot restore.

    I deleted a program by mistake and now when I try to do a system restore, I get a message that it was defective and that you cannot restore.

    I tried at least three different times to restore and the same message to arrive when it's over.
    It all started yesterday when I started the computer and it says windows cannot open and it says that he who sets.
    It won't let me even reinstal the program I deleted it goes on to say that missing microsoft. NET 4, but it is already on the computer
    and there the critical updates installed for microsoft. NET.  Help please

    Hello

    If you have problems with the system restore, this can help you:

    1. If you are using Norton, you should disable Norton inviolable Protection before using the system restore.

    http://Service1.Symantec.com/support/sharedtech.nsf/pfdocs/2005113009323013

    2. try to use Safe Mode system restore.

    http://bertk.MVPs.org/html/restoresysv.html

    3 Malware will stop at the system restore.

    Download, install, update and scan your system with the free version of Malwarebytes AntiMalware, if necessary in Mode safe mode with networking:

    http://www.Malwarebytes.org/products/malwarebytes_free

    And here's how to go in Safe Mode options; Select safe mode with networking from the list of options:

    http://Windows.Microsoft.com/en-us/Windows-Vista/start-your-computer-in-safe-mode

  • Windows automatically restarts constantly, cannot access the system restore point, cannot access the computer in safe mode

    Hi all

    For the not 24 hours I tried to access my computer in normal mode. When I turn on the pc, it says "configuration data 1 of 3 steps...". 0% complete"he never spent 0% and within seconds, it automatically restarts and starts again. It's so frustrating! I have a windows vista pc (purchased in ' 06). I can only access my desktop in SafeMode.

    I tried to perform a system restore, but not like he says "recovery disk is not the restore point selected. What should I do? I tried to manually create a restore point, but cannot access the system and Maintenance, while in safe mode. I can't do anything but literally access the internet. How can I get Windows back to factory settings it is with these limited resources? I have a Dell reinstallation DVD.

    I searched my programs and found that recently Windows automatically updated and downloaded "Microsoft Powerpoint Viewer" and "for 2007 Office system Compatibility Pack '. Now, I think it has something to do with it, because they were the most recent updates, before the pc crashed. But I also fear that it may be a virus, which has completely hijacked this PC. How am I supposed to get rid of a bug, if I can't even get the necessary antivirus?

    Sorry for the ranting, but it's so stressful when my pc is completely down. Please, please please help me. Thank you in advance for reading this same!

    Arianne

    Hello

    you talk about restore and system recovery disc in the same breath

    they are 2 different things

    and you can NOT create a restore of yesterday and today!

    yesterday is gone

    If it does not already; You can't do

    1st thing to try is a restoration of the system in safe mode

    http://www.windowsvistauserguide.com/system_restore.htm

    Windows Vista

    Using the F8 method:

    1. Restart your computer.
    2. When the computer starts, you will see your computer hardware are listed. When you see this information begins to tap theF8 key repeatedly until you are presented with theBoot Options Advanced Windows Vista.
    3. Select the Safe Mode option with the arrow keys.
    4. Then press enter on your keyboard to start mode without failure of Vista.
    5. To start Windows, you'll be a typical logon screen. Connect to your computer and Vista goes into safe mode.
    6. Do whatever tasks you need and when you are done, reboot to return to normal mode.

    If that does not read this information

    the link below is how to download and get a vista disk startup repair, which you can start from the

    http://NeoSmart.net/blog/2008/Windows-Vista-recovery-disc-download/

    Here's how to use startup repair system restore command prompt, etc. to bleepingcomputers link below

    http://www.bleepingcomputer.com/tutorials/tutorial148.html

    to boot from the dvd drive to be able to you will see a way to get into the bios Setup at the bottom of the screen or command menu start

    It would be F2 or delete etc to enter the BIOS or F12 etc. for the start menu

    Change boot order it do dvd drive 1st in the boot order

    http://helpdeskgeek.com/how-to/change-boot-order-XP-Vista/

    The malware removal:

    Download update and scan with the free version of malwarebytes anti-malware

    http://www.Malwarebytes.org/MBAM.php

    You can also download and run rkill to stop the process of problem before you download and scan with malwarebytes

    http://www.bleepingcomputer.com/download/anti-virus/rkill

    If it does not remove the problem and or work correctly in normal mode do work above in safe mode with networking

    Windows Vista

    Using the F8 method:

    1. Restart your computer.
    2. When the computer starts, you will see your computer hardware are listed. When you see this information begins to tap theF8 key repeatedly until you are presented with theBoot Options Advanced Windows Vista.
    3. Select the Safe Mode with networking with the arrow keys.
    4. Then press enter on your keyboard to start mode without failure of Vista.
    5. To start Windows, you'll be a typical logon screen. Connect to your computer and Vista goes into safe mode.
    6. Do whatever tasks you need and when you are done, reboot to return to normal mode.

    Reinstall vista from Dell DVD

    http://supportapj.Dell.com/support/topics/global.aspx/support/DSN/en/document?journalid=67E9C215C4BABD6CE040AE0AB5E14F05&docid=339949

  • Cannot open program (0 x 80070057 erro) system restore point - details below

    Hi people. I open the program of system restore point can´t, it displays the folow error message: unexpected error. incorrect setting. 0 x 80070057. the restoration of the system will be closed. (or something like that). Someone knows how to fix this? What happened, I have never had any problems with my windows vista before. Very thanks! Pedro Pacheco of the Brazil (and sorry for my bad English)

    There may be several reasons for the restoration of the system do not have to work.

    1. If you are using Norton, disable it before using the system restore.
    Norton will interfere with system restore.

    2. try to use Safe Mode system restore:

    Restore point:

    Try typing F8 at startup and in the list of Boot selections, select Mode safe using ARROW top to go there > and then press ENTER.

    Try a restore of the system once, to choose a Restore Point prior to your problem...

    Click Start > programs > Accessories > system tools > system restore > choose another time > next > etc.

    3. malware stops at a system restore.
    Try a scan of your system:

    http://www.Malwarebytes.org/MBAM.php

    Malwarebytes is as its name suggests, a Malware Remover!

    Download the free Version from the link above.

    Download, install, upgrade and scan once a fortnight.

    http://www.Spybot.info/en/index.html

    Spybot Search & Destroy 1.6.2 is a very good Anti-Spyware FREE program.

    Download, install, update and immunize your system with it.

    Then ANALYZE with her.

    Update and scan your system once a fortnight

    See you soon.

    Mick Murphy - Microsoft partner

  • cannot change the date and time in the system restore

    How can I change the date and time in the system restore? When I try to create a new restore point, I can't change the date and time, the system automatically date and time in.

    System Restore will always set the date and time of any restore point created at the effective date and time of the machine.

    If you want to restore your computer to a date and an hour earlier, you must select restore from a restore point that was created at the earlier time.  This article explains how.

    With the help of the Windows Vista system restore
    http://www.howtogeek.com/HOWTO/Windows-Vista/using-Windows-Vista-system-restore/

    My apologies if I misunderstood your question.  Why should change you the date and time when a restore point was created?  The only possibility of achieving a fictitious date and time will result in a change as actual date and time Windows or in the Bios, either option with unforeseen consequences.

Maybe you are looking for