Canon powershot a2000 is not connecting to the computer

Similar Questions

• Envy 15 t-j100 Select Edition: the device is not connected to the computer. Please insert the authentication device.

  Hello

  So I'm working on a LT desire that has been upgraded from Windows 8.1 to 10 recently and it is this message on the login screen "the device is not connected to the computer. Insert the authentication device. We can't identify what it means or what needs to be done to clear the screen. The user States that the fingerprints of impression of BIO sensor doesn't seem to work either. I looked in the Device Manager, and I see a Synaptics PS sensors (WBF) listed here and is properly installed. I even updated the driver of sensor ep on the support site of the desire, and we still see on the login screen.

  Y at - it no information or help to clear this message?

  We also note that the number on the keypad lock seems to be disabled during startup of windows 10 upwards. Before on windows 8.1 has been activated. Is there any setting to 10 to keep the active number lock.

  The user says if 10 can be made to work well, then we can go back to 7 or 8.

  Please notify.

  Thank you for your time.

  Seems to have been resolved in re - install the software HP Simple pass then go and reconfigure the settings. Message no longer appears on 10. User LT installed with 7 however. Best decision.

• printer wireless HP not connected to the computer

  My son tried hang our laptop wireless, with no result, since then the printer says not connected to the computer.

  Hi sharryn1940,

  In addition to Michael post, you can also find some good information at the following link:

  http://Windows.Microsoft.com/en-us/Windows7/install-a-printer-on-a-home-network

  I hope this helps!

  Debra
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think

• Whenever I try to send a fax, I get error "no dial tone was detected. The telephone line is busy or not connected to the computer. »

  Whenever I try to send a fax, I get: "no dial tone was detected. The telephone line is busy or not connected to the computer. "Any ideas?

  You can't send a FAX via a connection to broadband. Fax is essentially specialized phones and requires that a service composition is used at BOTH ends.

  You can buy an analogue Fax/modem (USB types work well enough) or use a service to convert fax email...

• H233H"cable not connected" with the computer is turned off

  My H233H monitor displays an annoying blue "cable not connected" when my computer is off or in stand-by mode.  Monitor works find out otherwise and all the buttons on the front panel work.  But impossible to find a setting that will turn the monitor off when the computer stops sending a signal.

  If I unplug the cable from the monitor to the computer's HDMI, should not the monitor eventually fade or go to sleeo?  Or will she continue to display this message "cable not connected" blue indefinitely?

  Thank you

  Well, I realized that it is a problem of Acer monitor with HDMI input.

  There is no problem if I connect my H233H monitor with VGA or DVI cable.

  Just thought I'd come back and answer my own question if someone ever comes back here with a similar problem.

  Good luck...

• Install the device driver of printer not connected to the computer

  My printer is too old to connect to my new computer.  I want to "print to a file" and move the file to another computer on which the printer connected (this second computer is not connected to the internet). How can I install device driver on the new computer with no attached printer?

  Hello

  1. What is the brand and model of the printer?

  If you want to move the file to another computer, you can copy the file to the flash drive and move to the other computer, so that you can print the file.

  Check out the links.

  http://www.Microsoft.com/resources/documentation/Windows/XP/all/proddocs/en-us/sag_setup_indirect_printer.mspx?mfr=true

  http://support.Microsoft.com/kb/308028

  http://Windows.Microsoft.com/en-us/Windows/help/printer-problems-in-Windows

  http://support.Microsoft.com/kb/293118

  http://Windows.Microsoft.com/en-us/Windows-XP/help/Setup/move-files-and-settings-to-new-computer

• My Explorer Microsoft touch does not connect to the computer (Win 8 and 7 or iMac)

  I bought a touch of Explorer Microsoft wireless mouse and cannot understand why the mouse does not connect. The small usb dongle is recognized and the mouse turns works. The optical light is blue and the touch sensor clicks when I run my finger on it. Nothing happens when I press any button of the mouse (without interaction with the computer). It almost seems like its not even connected to the usb dongle. I tried to find out what's wrong with it or with Windows. The mouse itself doesn't simply plug the usb dongle or on the computer at all. It is not a Bluetooth mouse, so there is no button to connect or sync.

  Hello

  As it seems to be a hardware problem, you can check the link for the Microsoft Hardware supported:

  http://www.Microsoft.com/hardware/en-in/support

• Start the virtual machine and wait for WF, does not connect to the computer virtual for Vds (Windows 2008 R2)

  Hello

  See a strange problem with only a Windows 2008 R2 model. When you use the built-in function "Start VM and wait" workflow to start a virtual machine (after conversion from a template either manually, or through workflow) NIC of the virtual machine (I tried VMXNET3 and e1000 times) does not connect to the problem. Vds can be replicated in a different VCenter, so spreading the vds. I also created several models of Windows 2008 r2 and all have this problem.

  If the model is converted and started outside VRO, it gets an IP from and is connected to the VDS immediately

  Tried add/remove the NIC of the model

  Tried to move the comments on different hosts

  Tried to create a new template from scratch

  NOTE: Windows 2012 R2 doesn't have this problem in the same circles, the only constant is the Windows 2008 R2 being started by VRO.

  Anyone seen this before?

  I found this article and it fixed my problem VMware KB: registration or the deployment of a virtual computer model fails apparently a fix a problem in ESX 5.1, 5.5 (I used the option to get around and things are good)

• failed to install for photosmart b109 all-in-one a - m. has said usb not connected to the computer

  I replaced Vista with a new version of windows 7 64-bit and cannot get my HP Photosmart B109 all-in-one a - m at the end of the installation I downloaded from the HP site. I uninstalled this printer as suggested before attempting the download. He gets to the part where you plug in the power and then the lights on the printer the computer tells me that my USB key is not plugged into it. I tried changing USB website and tested the USB connections and ensure that they work on the computer, but still the same response. The program then continues to stay on the installation of the final software and never complete. Talked with a local tech guy who suggested that you contact because he has no idea.

  Hi, thanks for the suggestion. However, I did not upgrade but remove vista altogether. I found the problem after a lot of grief and research - there was a cord that had fallen on the back of the library that was not plugged in!

• HP psc 5520 does not connect to the computer via the wireless

  Hello
  Recently I have not been able to print or scan anything using my laptop.

  Laptop computer and printer are connected wirelessly to my home network but when I try to set up the printer with a wi.fi connection, the laptop computer does not find the printer. I tried to do it with the hp software and windows options.

  If I connect the printer to the laptop via USB, everything works fine.

  The printer is only 2 months old and I'm getting a little frustrated, I'm totally lost here.

  Please help me

  If you need more information just ask.

  Thank you very much for this information.

  Were you running a power cycle on your router, the computer and the printer? Still, the IP address is all zeros? Please let me know!

• Network and sharing Center shows not connected, but the computer is connected to the wireless network

  When I open the network and sharing Center, or hold my mouse pointer on the icon of internet connection in the bottom right of the taskbar, it shows that I'm not connected to a network. However, I know that I'm connected to the internet. My internet and e-mail work correctly. Also, when I click on the 'Connect to a network' option, find the list of available wireless networks, and it shows that I'm connected to my home network. How can I make Windows everywhere where I am connected to the internet, instead of recognizing only on the list of the networks without wire-available?

  Had exactly the same problem on Windows 7 (win7). Connected to the Internet but the status showing no connection and a red cross on the network icon. Problem has also caused problems to connect to Lync and Office365 along with VPN, which apparently uses the status to check whether the connection is available.

  Found the solution here: http://social.technet.microsoft.com/Forums/en/w7itpronetworking/thread/df17c593-e78f-4878-97b0-7569307934c5

  Apparently, certain permissions gets hurt in the database record and must be fixed using RegEdit. The solution is a step by step and likely to be resolved simply by removing a cache of file using RegEdit and potentially affecting certain permissions.

  It will be useful.

• I have a problem with the wireless is not connecting on the computer.

  I have my adsl connected by Ethernet to my pc but it does not work when I take the cord Ethernet how to pass Ethernet Wireless on the pc?

  Hello
  Is your ADSL wireless router option supports?
  If Yes, to connect to the ADSL router, go to Wireless ADSL router, enable the wireless option and set it up using your ID and password provided by your service provider, connect.
  You can configure a dedicated connection to your PC using the MAC ID and by doing that you can limit the other device to access your wireless network.

  Implementation process

  1::Sert Cook addaress PC IP is equal to the router IP address range
  2::enter Roter IP in the URL box
  3::go to wireless to the router configuration
  4:enable wireless in the router setup

• DSC - 100M 2 RX does not connect to the computer

  It's weird... when I bought the camera, he set up and connected without issue to my laptop (Windows 7, 64 bit, SP-1). When I connect it now, the computer doesn't respond (i.e., the popup asking what you want to do) and the icon under devices and printers is still grayed out. I removed the camera devices and printers and use Device Manager to remove the driver, and rebooted, thinking that it detects the camera and reinatall the driver software device.

  Evil. Still does nothing, and 'add a device' under devices and printers does not detect the device when it is connected. The unit displays the "Connection" icon on the screen, using the cable USB are provided, close to 100% battery and tried all the USB ports on the laptop (that work perfectly with the USB sticks, external hard drives and other devices).

  Any ideas on how I can get them to recfonnect would be appreciated... Thanks in advance!

  Good day BobV55!

  It is indeed strange and to solve the problem, try the steps on this link: the computer does not recognize the USB connection from a Sony camera.

  If my post answered your question, please mark it as "accept as a Solution.

• Router is not connecting to the computer

  I just replaced a bad on my computer's ethernet jack.  Now when I plug the router in there I don't get everything internet.  The router has internet and my laptop wireless connects fine via the wireless signal...  I replaced the power cord from the router to the computer with a brand new, only one I know works.  Still no internet.  When I look at the network settings, the computer says that it is connected to the router.  But no internet signal.  I also plugged the network directly into the computer and it works fine.  The ethernet jack is working.  Any suggestions?  I don't have the book and cd for the router...

  Mike

  Perform the following steps:

  # Open the browser and in the address bar type 192.168.1.1 which will open the router configuration page.

  # Bring back the MTU (Maximum Transmission Unit) of 1500 to 1400 or less (usually found on the main page / basic configuration of your router).

  # Click on wireless tab select width of the channel to 20 MHz only and channel 6, 9 and 11.

  Settings wireless #Adjust the following:

  ~ ~ Reduced from 100 to 75 beacon interval

  ~ ~ Lower the threshold of fragmentation of 2346 to 2306

  ~ ~ Lower 2347 to 2304 RTS threshold

  Then check the wireless...

• code 45 currently, this hardware device is not connected to the computer.

  Separated from this thread.

  WIN 7

  Same thing happened to one of several HARD drives. Replaced HARD drive and the substitution works as expected.

  Apparently the problem is the HARD drive and not the connection

  Drive HARD original also causes the message to format the drive. Something is not right.

  Greg

  Very complete. Thank you very much. I'll upload what I can.

  SOLUTION:

  I disconnected all the wires of the Mboard and cleaned all contacts and Sockets with flattened q - Tip and iso. alcohol. That cures the problem. However, a test of Seagate indicates a disk would become a problem. Cleaning tips was also on MS help pages too.

  Greg