code 45 currently, this hardware device is not connected to the computer.

Similar Questions

• Envy 15 t-j100 Select Edition: the device is not connected to the computer. Please insert the authentication device.

  Hello

  So I'm working on a LT desire that has been upgraded from Windows 8.1 to 10 recently and it is this message on the login screen "the device is not connected to the computer. Insert the authentication device. We can't identify what it means or what needs to be done to clear the screen. The user States that the fingerprints of impression of BIO sensor doesn't seem to work either. I looked in the Device Manager, and I see a Synaptics PS sensors (WBF) listed here and is properly installed. I even updated the driver of sensor ep on the support site of the desire, and we still see on the login screen.

  Y at - it no information or help to clear this message?

  We also note that the number on the keypad lock seems to be disabled during startup of windows 10 upwards. Before on windows 8.1 has been activated. Is there any setting to 10 to keep the active number lock.

  The user says if 10 can be made to work well, then we can go back to 7 or 8.

  Please notify.

  Thank you for your time.

  Seems to have been resolved in re - install the software HP Simple pass then go and reconfigure the settings. Message no longer appears on 10. User LT installed with 7 however. Best decision.

• Error message: "Windows cannot start this hardware device because its configuration (in the registry) information are incomplete" and DVD disc is not recognized.

  Original title: My DVD drive is not recognized, it works physicaly works fine, but the pc does not even detect it exists.

  The error that says: "Windows cannot start this hardware device because its configuration (in the registry) information are incomplete."

  I did a backup and restored my system to the factory settings. After doing this still dvd was not recognized. I don't know what to do, my computer is new and Security told me that they will restore the pc and try to fix it, I can't risk my documents of the University are the same that has not worked for me before.
  Could someone help me?
  -The pilot is the last in line.
  -The works of reader dvd but the computer is not reading it, it does not even appear on the section 'computer '.
  -J' tried to use a "fix - it" on Microsoft online, but it doesn't work anymore.
  -My OS is Windows 7.
  -A restore factory settings did not work at all.
  Thank you.
  Claudio Nahmad
  Mexico City

  Hi, Claudio Nahmad,.

  This error can occur if the data in the registry for the device and its driver has been corrupted.

  Since you have already done a factory restore, leave, try to uninstall and reinstall the driver CD\DVD and check if it helps.
  Code 19: Windows cannot start this hardware device because its information of configuration (in the registry) is incomplete or damaged

  We can also refer to article and check if it helps.

  Your CD or DVD drive is missing or is not recognized by Windows or other programs

  Important: The above links contains steps to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs.

  For more information, you can view the article:

  Back up the registry

  You can also try to install Windows updates, including optional updates driver and check if that helps.

  Install Windows updates in Windows 7

  Hope the helps of information.

• I get this error message with my DVD player: "Windows cannot start this hardware device because its configuration (in the registry) information are incomplete."

  I get this error message with my DVD player: "Windows cannot start this hardware device because its configuration (in the registry) information are incomplete." I tried to reinstall the driver when the computer prompted me to do it, but there was an error with this as well. My computer will not all read the disks.

  Original title: Matshita DVD-R UJ 890

  Hi AJordanMiller,

  Try these methods.

  Method 1

  Run the fix - it from the link below.

  Hardware devices not detected or does not
  http://support.Microsoft.com/GP/hardware_device_problems

  Method 2

  See the help article:

  Your CD or DVD drive is missing or is not recognized by Windows or other programs
  http://support.Microsoft.com/kb/314060

  Registry warning: Important This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base:

  How to back up and restore the registry in Windows 7

  http://Windows.Microsoft.com/en-us/Windows7/back-up-the-registry

  It will be useful.

• Error: Your device is not connected to the Internet.

  Hello

  I have a dash HID - B70 model and until last week it works fine. I used about 2 weeks ago and have had on energy saving mode after that. I tried to use it again a couple of days, and when I typed on the screen the unit remained in power save screen and showed a yellow above the clock error message: "your device is not connected to the Internet. Press to reconnect. "I hit this button and the unit tried to reconnect, but will still end up back in the same error message and the screen.
  I tried to push the reset button on the device, but I still see the same black screen and the clock with the error message once it restarts. I unplugged my wireless router and managed to get the device to show me the other wireless networks, then I plugged the router back in and reconnected (device showed that the connection was successful), but then he went immediately to the error screen.
  I can't the unit to go to the home menu at all, no matter what button I push, if unfortunately I can't even reset to factory settings to avoid the problem.

  Any advice on how to fix this? I do know not why it happened because I didn't have the routers or wireless providers, nor have I added all devices on my home network.

  Thanks in advance for your help.

  
  

• 9.3 OS does not complete on my iPad 2 get message that device is not connected to the Internet, when it exists, a solution?

  WWhen updated my iPad 2 with OS 9.3, when I finally install, during the verification step, message, is that the device is not connected to the Internet when connected. Anyone else have the problem? All solutions?

  Sesame problem on my iPad mini I want to finish the update already

• printer wireless HP not connected to the computer

  My son tried hang our laptop wireless, with no result, since then the printer says not connected to the computer.

  Hi sharryn1940,

  In addition to Michael post, you can also find some good information at the following link:

  http://Windows.Microsoft.com/en-us/Windows7/install-a-printer-on-a-home-network

  I hope this helps!

  Debra
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think

• Whenever I try to send a fax, I get error "no dial tone was detected. The telephone line is busy or not connected to the computer. »

  Whenever I try to send a fax, I get: "no dial tone was detected. The telephone line is busy or not connected to the computer. "Any ideas?

  You can't send a FAX via a connection to broadband. Fax is essentially specialized phones and requires that a service composition is used at BOTH ends.

  You can buy an analogue Fax/modem (USB types work well enough) or use a service to convert fax email...

• Install the device driver of printer not connected to the computer

  My printer is too old to connect to my new computer.  I want to "print to a file" and move the file to another computer on which the printer connected (this second computer is not connected to the internet). How can I install device driver on the new computer with no attached printer?

  Hello

  1. What is the brand and model of the printer?

  If you want to move the file to another computer, you can copy the file to the flash drive and move to the other computer, so that you can print the file.

  Check out the links.

  http://www.Microsoft.com/resources/documentation/Windows/XP/all/proddocs/en-us/sag_setup_indirect_printer.mspx?mfr=true

  http://support.Microsoft.com/kb/308028

  http://Windows.Microsoft.com/en-us/Windows/help/printer-problems-in-Windows

  http://support.Microsoft.com/kb/293118

  http://Windows.Microsoft.com/en-us/Windows-XP/help/Setup/move-files-and-settings-to-new-computer

• H233H"cable not connected" with the computer is turned off

  My H233H monitor displays an annoying blue "cable not connected" when my computer is off or in stand-by mode.  Monitor works find out otherwise and all the buttons on the front panel work.  But impossible to find a setting that will turn the monitor off when the computer stops sending a signal.

  If I unplug the cable from the monitor to the computer's HDMI, should not the monitor eventually fade or go to sleeo?  Or will she continue to display this message "cable not connected" blue indefinitely?

  Thank you

  Well, I realized that it is a problem of Acer monitor with HDMI input.

  There is no problem if I connect my H233H monitor with VGA or DVI cable.

  Just thought I'd come back and answer my own question if someone ever comes back here with a similar problem.

  Good luck...

• My Explorer Microsoft touch does not connect to the computer (Win 8 and 7 or iMac)

  I bought a touch of Explorer Microsoft wireless mouse and cannot understand why the mouse does not connect. The small usb dongle is recognized and the mouse turns works. The optical light is blue and the touch sensor clicks when I run my finger on it. Nothing happens when I press any button of the mouse (without interaction with the computer). It almost seems like its not even connected to the usb dongle. I tried to find out what's wrong with it or with Windows. The mouse itself doesn't simply plug the usb dongle or on the computer at all. It is not a Bluetooth mouse, so there is no button to connect or sync.

  Hello

  As it seems to be a hardware problem, you can check the link for the Microsoft Hardware supported:

  http://www.Microsoft.com/hardware/en-in/support

• Start the virtual machine and wait for WF, does not connect to the computer virtual for Vds (Windows 2008 R2)

  Hello

  See a strange problem with only a Windows 2008 R2 model. When you use the built-in function "Start VM and wait" workflow to start a virtual machine (after conversion from a template either manually, or through workflow) NIC of the virtual machine (I tried VMXNET3 and e1000 times) does not connect to the problem. Vds can be replicated in a different VCenter, so spreading the vds. I also created several models of Windows 2008 r2 and all have this problem.

  If the model is converted and started outside VRO, it gets an IP from and is connected to the VDS immediately

  Tried add/remove the NIC of the model

  Tried to move the comments on different hosts

  Tried to create a new template from scratch

  NOTE: Windows 2012 R2 doesn't have this problem in the same circles, the only constant is the Windows 2008 R2 being started by VRO.

  Anyone seen this before?

  I found this article and it fixed my problem VMware KB: registration or the deployment of a virtual computer model fails apparently a fix a problem in ESX 5.1, 5.5 (I used the option to get around and things are good)

• Canon powershot a2000 is not connecting to the computer

  the driver software for my Canon powershot a2000 is not connect to my computer... any suggestions?

  Chester

  http://www.Microsoft.com/Windows/compatibility/Windows-Vista/default.aspx

  Windows Vista Compatibility Center

  First thing to do is to check its compatibility Vista at the link above, and if not to see what are the solutions/patches are available from Canon.

  If it's Vista compatible > uninstall it, if installed > Re-download/save to your desktop > right click on setup.exe O run as admin.

  See you soon.

  Mick Murphy - Microsoft partner

• BlackBerry Smartphones when you try to synchronize, it says: this device is not connected to the internet

  IGet this error message: "the computer must be connected to the internet to set up initially sync settings. Make sure you are able to connect to the internet, and then try again. »

  Computer is connected. Checked with for updates Desktop Manager and we are caught in the Web of Blackberry site. What should I do to make it work now?

  Thank you very much for your help!

  Read this link, is another thread with the same problem

  http://supportforums.BlackBerry.com/Rim/Board/message?board.ID=BlackBerryDesktopSoftware&thread.ID=5...

  Read what bifocal post.

• Smartphones blackBerry 8520 bb curve blackberry software doesn't have a software device blackberry for the device you have connected to the computer

  the last time that I update it this is in version 5, but when I click on update download update again and suddenly, it was frozen and the result when I start my bb is reload software: 507

  I read on the forums, but I can't work with this

  

  

  Hi and welcome to the Forums!

  On your PC (you cannot do this on MAC):

  1) uninstall all the BB OS packages from your PC,

  (2) make sure you have the BB Desktop Software already installed

  • http://us.BlackBerry.com/apps-software/desktop/?lid=us:BBsoftwareesktopSoftware & Cal = us: bbsoftware

  (3) download and install to your PC, the BB OS package you want:

  • http://us.BlackBerry.com/support/downloads/download_sites.jsp

  (4) If this OS package comes from one carrier other carrier for which your BB was built, then remove, on your PC, all copies of the SELLER. XML... There will be at least one and maybe 2, and they will be located in the same way or to (it changes based on your version of Windows) these files:

  • C:\Program Files (x 86) \Common Files\Research In Motion\AppLoader
  • C:\Users\(your Windows username) \AppData\Roaming\Research In Motion\BlackBerry\Loader XML

  (5) run the Desktop software and connect your BB... the software should offer the operating system package you have installed on your PC. If, during the process, your BB votre BB a '507' error, simply unplug the power cord of the BB USB and reinsert it. do nothing else... This should allow the installation to continue.

  Do not forget to save.

  If you are on a MAC, you are limited to only your sanctioned carriers OS packages... but can still use any level they currently have to sanction. See this procedure:

  • KB19915 How to perform a clean reload of the smartphone BlackBerry using BlackBerry Desktop Software application software

  Good luck and let us know!