Causing the discs to launch constantly MySQL
Hi all
I use MySQLOn to allow the use of the construction in MySQL on my ReadyNAS 2100 with 4.2.17 (instead of 4.2.18T6), and after turning off pretty much everything (except for SMEs/SMIs), came to the conclusion that MySQL is the cause of my drives constantly turning up. The database on the box is not huge, it's 20 MB - a database that is shared between two boxes of Kodi as the Raspberry Pi. Is it possible to making it serve the database memory cache rather than turn drives upward? It is never authorized discs stay turned down more than 10 minutes!
Best,
Colin
No worries, I moved the database to one of my other servers and MySQLon removed from the ReadyNAS - he was happily sleep for an hour now.
Sad that the only altered thing me a problem has been the huge spike in my electricity bill - he used to sleep under the 4.2.27 until I upgraded to 4.2.28T6, decommissioning had no effect. Yet, the question is sorted into force now
Thank you!
Tags: Netgear
Similar Questions
-
Update of HP Z620 BIOS causing the disc start plu
Dear Sir
I updated the system of workstations HP Z420/Z620 (International) BIOS
to 03.69 Rev.
18 June 2014 to my windows 7 Professional. After the reboot, it could not find my boot drive. In the Bios, the order of boot to SATA drive name list is totally a mess, named as "SS", instead of SATA0, etc..I boot from my CD of windows 7 Professional and try to fix the system, but he said something like a different type of system.
What a bad upgrade experience and please help me to recover!
P.S. This thread has been moved from workstations - Itanium-Based, hp9000, Visualize for workstations - w series, series z, legacy x and xw series. Forum Moderator - HP
Not sure what would happen when your update of the system BIOS, but the BIOS flashing can be risky, especially if you get a power disruption or during the writing of the BIOS itself, there are a few other firmware issue. For this reason I almost always perform updated the BIOS when the system is connected to the inverter to limit the outages momentary causing failures flash.
HP also have even known to release a BIOS and then remove it on their download page for undocumented reasons. These reasons may or may not be related to flash failures or other problems, we do not know, only HP really knows, but they don't say.
For your Z620, you can see the gaps in the list of the BIOS version specified in the last note of release of the BIOS itself. In fact the release notes state that you require 1.07 update to 3.52 or later and says that he must first update to 1.23 (which curiously is not included in the version below the list!).
So you SHOULD ALWAYS read the BIOS release notes. In fact, you should read all release notes of all BIOS versions available in order to make sure that you know what has changed and what prerequisites indicators exist. It's tedious but better than a flash failure.
Anyway, from the issue date BIOS, you will notice that your BIOS must be at 1.07 or later to be able to upgrade successfully to a BOS 3.05 or later version. Therefore, you should check to see what BIOS you have done and if you have < 1.07 you MUST update to the latest version of the BIOS BIOS 1.x (to 1.14 BIOS of my reasoning, because it is the most recent in the history of the versions) as it is a sine qua non.
In fact, I would update BIOS 1.14, then update a BIOS 2.08, then BIOS 2.55 before if we consider a 3.05 BIOS and more late a 3.69 BIOS updated. It is pedantic, Yes, but perhaps a bit more secure (especially if you use an inverter). I always check the version of the BIOS and BIOS (and so the BIOS settings) after each flash before jumping into the OS...
But even if you cannot start the operating system, you should be able to Flash the BIOS as follows:
- install 7-zip on a work computer
- Download the bios appropriate 1.14 or 3.69 for your system and save it
- Right click the bios file saved, spxxxxx.exe, and then select < 7 - zip > < archive open >
- Double-click the folder (not name) stated in 7 - zip file manager
- Double-click on "bios falsh.htm" and read the "flash back" and or sections of "failsafe bootblock recovery."
- Follow the appropriatesection of those that you just read...
Therefore, if your system messages, and you can actually get into the BIOS, use the flash BACK method. And depending on what version of BIOS your system indicates boot buring, flashing the BIOS is appropriate (if the system shows BIOS 1.14 1.x then flash, if the system indicates BIOS 3.x then flash 3.69). I hope that this will ensure that your BIOS has been flashed properly.
Once you are sure that the BIOS is the correct version and date, then look at all the parameters and, hopefully, HARD drive names are listed correctly and your boot disks/raid volume can be found.
It's also a good idea to go into the BIOS and hit < LTRC > < A >, then go in "system ID and check the entries against the labels on your machine." Pay special notice that the BuildID, SKUNumber & ProductName in BIOS match labels (because they must be correct for the HP system to work recovery discs)...
The only other thing I can think is that you had two or more HARD drive in a RAID configuration and RAID configuration somehow I messed up. If you use RAID, maybe watch the configuration by pressing CTRL + R or CTRL-C while booting. Do not change anything, because you might lose your data, just look.
If these things do not help, you will need to be very precise about what you did, what configuration you have, state that the system is and what error messages you receive. You can use a camera and post here as appropriate as someone may be able to help and take some snaps different pages problem BIOS configuration screens, configurations, error messages or other...
It is also unknown if you use an image from HP and referring to HP system recovery disks or you did (re) installed a vanila MS Win7Pro OS using a disc to install MS Win7. And write "something like a different type of system" is not as useful as the actual error message you get.
-
After I installed and opened a Silkroad Online on my Windows 7 64 bit, an error pops up: Silkroad Online Launcher has stopped working, and a close button the program. Any ideas on this subject? I tried to disable the firewall and antivirus software and restart the game, but it didn't work... I don't know what to do. The whole eror massage: Silkroad online Launcher has stopped working. A problem caused the blocking of the program works correctly. Windows will close the program and notify you if a solution is available
It is a file you need to edit in Notepad in the game directory. I would contact the manufacturer of the game as to what exact file. I have not personally done it, but I've seen this fix on other forums. MCP. MCDST. LVL 80
-
iMac very slow and short HOT. the fan runs almost constantly
My iMac 2011 short middle slow and often gets "the ball" of the computer runs hot (uncomfortable keep the hand on top) and the fan is almost always running. Activity monitor shows the low CPU usage. Any ideas?
EntreCheck report is due to:
EtreCheck release: 2.9.4 (254)
Report generated 2016-02-18 12:04:46
Download EtreCheck from http://etrecheck.com
Time 03:31
Performance: good
Click the [Support] links to help with non-Apple products.
Click [details] for more information on this line.
Problem: Another problem
Description:
iMac computer is slow, get the beach ball often enough and the fan runs almost constantly because the computer heats
iMac (27 inch, mid 2011)
[Data sheet] - [User Guide] - [Warranty & Service]
iMac - model: iMac12, 2
1 2.7 GHz Intel Core i5 CPU: 4 strands
4 GB of RAM expandable - [Instructions]
BANK 0/DIMM0
OK 2 GB DDR3 1333 MHz
BANK 1/DIMM0
OK 2 GB DDR3 1333 MHz
0/DIMM1 BANK
Vacuum
BANK 1/DIMM1
Vacuum
Bluetooth: Old - transfer/Airdrop2 not supported
Wireless: en1: 802.11 a/b/g/n
AMD Radeon HD 6770M - VRAM: 512 MB
iMac 2560 x 1440
OS X Yosemite 10.10.5 (14F1605) - since the start time: about 5 days
WDC WD1001FALS-403AA0 disk0: (1 TB) (rotation)
EFI (disk0s1)
: 210 MB Macintosh HD (disk0s2) /: 999,35 go-go (577,56 free)
HD (disk0s3)
[recovery] recovery: 650 MB HL-DT-STDVDRW GA32N)
Apple Inc. FaceTime HD camera (built-in)
HP Photosmart 8400 series
Apple Inc. BRCM2046 hub.
Apple Inc. Bluetooth USB host controller.
Hub keyboard Apple, Inc.
Apple Inc. Apple Keyboard
Apple internal memory card reader
Computer, Inc. Apple IR receiver.
Apple Inc. Thunderbolt_bus.
Mac App Store and identified developers
/ System/Library/Extensions
com [loading]. Cycling74.driver.Soundflower (1.5.1 - 2016-02-09) [Support]
com.seagate.driver.PowSecDriverCore [no charge] (5.2.4 - 10.4 SDK - 2016-02-09) [Support]
/ System/Library/Extensions/Seagate storage Driver.kext/Contents/PlugIns
com.seagate.driver.PowSecLeafDriver_10_4 [no charge] (5.2.4 - 10.4 SDK - 2014-01-27) [Support]
com.seagate.driver.PowSecLeafDriver_10_5 [no charge] (5.2.4 - SDK 10.5 - 2014-01-27) [Support]
com.seagate.driver.SeagateDriveIcons [no charge] (5.2.4 - 10.4 SDK - 2014-01-27) [Support]
HP USB EWS Gateway: Path: Library/StartupItems/HP USB EWS Gateway
Startup items are obsolete in OS X Yosemite
com.apple.AirPlayUIAgent.plist [killed]
com.apple.CallHistoryPluginHelper.plist [killed]
com.apple.CallHistorySyncHelper.plist [killed]
com.apple.EscrowSecurityAlert.plist [killed]
com.Apple.cloudphotosd.plist [killed]
com.Apple.cmfsyncagent.plist [killed]
com.Apple.CoreServices.appleid.authentication.plist [killed]
com.Apple.gamed.plist [killed]
com.Apple.photolibraryd.plist [killed]
com.Apple.printuitool.agent.plist [killed]
com.Apple.RCD.plist [killed]
com.Apple.SBD.plist [killed]
com.Apple.telephonyutilities.callservicesd.plist [killed]
[loading] 141 tasks Apple
[operation] 58 tasks Apple
13 killed process lack of RAM
com.Apple.awdd.plist [killed]
com.Apple.ctkd.plist [killed]
com.Apple.Emond.aslmanager.plist [killed]
com.Apple.icloud.findmydeviced.plist [killed]
com.Apple.ifdreader.plist [killed]
com.Apple.nehelper.plist [killed]
[killed] com.apple.periodic - daily.plist
[killed] com.apple.periodic - weekly.plist
com.Apple.wdhelper.plist [killed]
[loading] 173 tasks Apple
[operation] 80 tasks Apple
9 killed process lack of RAM
[loading] com.maintain.CocktailPurgeInactiveMemory.plist (2013-11-21) [Support]
[failure] com.maintain.CocktailSystemEvents.plist (2012-07-08) [Support]
[loading] com.maintain.LogOut.plist (2014-02-17) [Support]
[loading] com.maintain.Restart.plist (2014-02-17) [Support]
[loading] com.maintain.ShutDown.plist (2014-02-17) [Support]
[loading] com.maintain.Sleep.plist (2014-02-17) [Support]
[operation] com.maintain.SystemEvents.plist (2014-02-17) [Support]
[loading] com.adobe.fpsaud.plist (2016-01-28) [Support]
[loading] com.maintain.CocktailScheduler.plist (2016-02-18) [Support]
[operation] com.memeo.WDMemeod.plist (2007-07-30) [Support]
[loading] com.rogueamoeba.hermes.plist (2010-09-28) [Support]
com.apple.MobileMeSyncClientAgent.plist [failure]
com.apple.SafariBookmarksSyncer.plist [failure]
[loading] com.google.keystone.agent.plist (2015-12-14) [Support]
[operation] ws.agile.1PasswordAgent.plist (2013-12-07) [Support]
iTunesHelper UNKNOWN (missing value)
HP Photosmart Menu Application (/ Applications/Hewlett-Packard/Photosmart/HP Photosmart Menu.app) (2006-10-22)
Airport demand of basic Station Agent (/ System/Library/CoreServices/AirPort Base Station Agent.app) (2014-10-07)
Request for SmileboxTray (/ Applications/Smilebox.app/Contents/Resources/SmileboxTray.app) (2016-02-12)
The messages application (/ Applications/Messages.app) (2015-08-19)
WDMemeoAgent Application (/ Library/Application Support/Memeo/WD anywhere Backup/Agents/WDMemeoAgent.app) (2009-06-24)
HP Scheduler application (/ Library/Application Support/Hewlett Packard/Software Update/HP Scheduler.app) (2010-09-17)
Director Docker Application (/ Applications/Hewlett-Packard/HP Photo & imaging software/HP Photo and imaging Director/Director Docker.app) (2006-10-22)
[operation] 2BUA8C4S2C.com.agilebits.onepassword4 - helper (2016-02-09)
com [running]. Growl.GrowlHelperApp.89492 (2006-12-30)
com [running]. Memeo.WDAnywhereAgent.87504 (2009-06-24)
[operation] com.apple.xpc.launchd.oneshot.0x1000000a.EtreCheck (2016-02-14)
[operation] com.smilebox.Tray.61376 (2016-02-12)
[operation] jp.co.canon.cijscannerregister.17640 (2011-05-04)
Flip4Mac WMV Plugin: 2.3.0.14 (2009-09-28) [Support]
FlashPlayer - 10.6: 20.0.0.306 - SDK 10.6 (2016-02-09) [Support]
QuickTime Plugin: 7.7.3 (2016-02-09)
Flash Player: 20.0.0.306 - SDK 10.6 (2016-02-09) [Support]
AdobePDFViewer: Unknown (2010-04-23)
Default browser: 600 - SDK 10.10 (2015-07-16)
Web of Google Earth plugin: 6.1 (2011-10-17) [Support]
Silverlight: 5.1.40728.0 - SDK 10.6 (2015-11-04) [Support]
DirectorShockwave: 12.1.7r157 - SDK 10.6 (2015-02-05) [Support]
iPhotoPhotocast: 7.0 - 10.8 SDK (2013-04-18)
RealPlayer Plugin: unknown
1Password (2016-01-25)
Flash Player (2016-01-28) [Support]
Flip4Mac WMV (2009-09-28) [Support]
Growl (2006-12-30) [Support]
Skip system files: No.
Mobile backups: OFF
Automatic backup: YES
Volumes to back up:
Macintosh HD: Disc size: 999,35 GB disc used: 421,79 GB
Destinations:
Time Capsul of Alan W. Voges [network]
Total size: 2.00 TB
Total number of backups: 65
An older backup: 08/29/15, 06:56
Last backup: 18/02/16, 11:39
Size of backup drive: adequate
Backup TB 2.00 size > (disc 421,79 GB X 3)
4% WindowServer
2% fontd
2% safari
1% kernel_task
1% sysmond
Top of page process of memory: ⓘ
633 MB kernel_task
Com.apple.WebKit.WebContent (4) 299 MB
172MO Mail
Safari of 147 MB
Overview of 78 MB
504 MB of free RAM
3.50 used GB RAM (1.12 GB being cached)
174 MB used Swap
February 16, 2016, 12:31:30 Library/Logs/DiagnosticReports/Mail_2016-02-16-123130_[redacted].cpu_resource. diag [details]
/Applications/mail.app/Contents/MacOS/mail
February 16, 2016, 08:15:06 /Library/Logs/DiagnosticReports/Inkjet6_2016-02-16-081506_[redacted].crash
/Library/printers/HP/cups/Inkjet6.driver/Contents/MacOS/Inkjet6
Ways to help make a slow Mac faster
17 reasons why your Mac runs slower than expected
Slow performance of Mac? This Article addresses!
Difficulty of slow start in OS X | MacFixIt - CNET Reviews
How to fix the slow down time and start. | MacTip.net
6 easy tips to speed up OS X Yosemite on your Mac.
Avoid using third-party software that claims to clean your computer. This software does more harm than good. In addition, you don't need it. Note that all computers become slower over time even in the normal conditions of use. Generally, the experienced users erasing the hard drive and do a clean install from scratch at least once a year or every time that the installation of a major upgrade of the OS. Well sure doing so also means that you need to maintain regular and several backups.
Add more RAM or reduce the number of simultaneously executed from applications and utilities. Remove unnecessary software such as anti-malware and that promises to clean your Mac. Look for the runaway process: Runaway applications can shorten the battery life, affect performance and increase the heat and fan acti... See also:
Before Mavericks
Open the activity monitor in the Utilities folder. Select all processes in the drop process . Click the % CPU column heading twice to display in descending order. If find you a process that uses a large amount of time processor (> = 70,) then select the process, and then click the quit icon in the toolbar. Click the force quit button to kill the process. See if that helps. Don't forget to mention the name of the runaway process, so you can find the cause of the problem.
Mavericks and later versions
Open the activity monitor in the Utilities folder. Select all processes in the menu display . Click the CPU tab in the toolbar. Click the % CPU column heading twice to display in descending order. If you find a process that uses a large amount of CPU %, then select the process, then click on the quit icon in the toolbar. Click the force quit button to kill the process. See if that helps. Don't forget to mention the name of the runaway process, so you can find the cause of the problem.
The ultimate solution
Back up everything, wipe the drive, reinstall OS X and restore your data from backup. Reinstall the third-party software of original/zero media.
-
How is it assistant BootCamp 6.0.1 running on El Capitan 10.11.5 installs single partition BootCamp on the disc Fusion consisting of 128 SSD part G SSD and 3 TB of HARD drive on an iMac (retina 5K, 27 inches, end of 2014), but not the part of the HARD drive?
This has two questions:
1 capacity of SSDS faster for Fusion drive has been reduced. Therefore less effective for the reader of the merger. For example if I need to create a partition of 80G for my windows bootcamp partition, only 48 G will be left in the drive of the merger.
2. ability of the bootcamp windows partition becomes very limited, cannot be greater than 120 G.
3. even when I try to fuse out of the drive of fusion in the 128 G SSD and 3 TB of HARD disk, and then run the BootCamp assistant to create the bootcamp partition start from scratch to reinstall El Capitan only on the HARD drive (without drive Fusion), it won't let me do anything, it just shows an error that says something like "a person has created additional partitions on this drive please select. another disc. But there is nothing else to choose.
Before my (5 K, 27 inches, end of 2014 retina) to El Capitan Yosemite, I was able to use the previous version of the wizard BootCamp 5.x to create the partition, bootcamp on the drive of the merger. And it will be divided in the fuser unit in two and insert the Bootcamp partition (with the size I chose, which can go up to 1 TB) between two partitions of MAC OSX.
The disk partitions resulting from it, will be the partition MAC OS x on the SSD, the partition MAC OS x on the HARD drive partition #1, partition MAC OS x on the HARD drive partition #3.
Then there is the BootCamp partition on the HARD drive partition #2.
Is there a way to get what I need?
That is what has been described in this notice of two canoes?
Installation of Windows on a Boot Camp partition on a drive of TB Fusion 3
Thank you.
After having worked on those weeks, I realized that I need very painfully (by first going back to Yosemite and bootcamp 5 to escape all the limitations of El Capitan and BootCamp 6) I want to share here. Someone at - it other smarter solutions welcome.
Note these steps and mentioned drivers only work for my version of iMAC, retina 5K late 2014. If you have other material, please search on the web to see which driver will work first. And all of these steps are destructive and assumed that you first take backup. It is only shared for interest only. Readers will have to bear your own risk.
A. take backup
1. take a backup completes my iMac Fusion Drive using Time Machine. Then restart with a Yosemite USB installation and select Terminal from the menu on the top bar.
B. fuse out of the merger in two physical disks drive: SSD + HDD
1. in the terminal, type the commands in show what the logical volume group ID and the ID of the logical Volume of the disc fusion)
Cs diskutil list
2. in the terminal, type commands for the fuse of the fuser unit and separate them to an SSD and a HARD drive. Note: All data will be destroyed in the drive of the merger. There are many articles in this community on how this could be done,
diskutil cs deleteVolume Logical Volume ID
CS diskutil remove logical Volume Group ID
This should finish within 30 minutes. If you have taken more time, this means that your reader of fusion has been altered somehow.
I hit this issue too. To use this command to remove the fusion drive hung up, and I need to do the hard to scramble a few sections of data in the hard disk partition table using the controls to tell the OSX this hard drive is a new without partitions:
Cat >/dev/random /dev/disk0 (where/dev/disk0 is the SSD)
and repeat for disk1/dev/disk1 which is the HARD drive in my case).
This command will not return anything, but expect to press Ctrl-Z to end after 1 minute.
2 create independent partitions (non-fusionend) for the installation of OSX.
Borne Terminal output, and select disk utility, in disk utility, select the drive to HARD disk (and not on the partition), you will see the error message and you will be asked if you want to fix the fuser unit, click on ignore. Then wipe the HARD drive to create a single 'extended OSX journaled"named"HARD drive".
3. Repeat step 2, and then erase the SSD drive to create a single 'extended OSX journaled"named"SSD ".
C. install on the HARD disk as drive didier autonomous not fusion.
1. go to Yosemite install screen and proceed with the installation of a clean copy of Yosemite to the iMAC. then connect you.
D. use BootCamp Yosemite f5 to install windows.
1. launch Yosemite bootcamp.
2. check the two checkboxes for creating the USB drive to install windows 7 or a later version, and to download the windows supports the Apple software. Do not click on the last box to install or remove windows pie creating real bootcamp partition again.
3. it may take several hours to complete this function of your internet b/w and also performance of your USB drive.
4. If you install Windows 7 (like me), then the downloaded drivers will not work for you, this will cause the issue of the device driver appleDSS.sys does not like this driver and others are too recent for windows 7 to use. Also, your keyboard and mouse may not work even if you try to plug in a USB external keyboard or a mouse. You need to replace the drivers downloaded by others (the Boot Camp 5.1.5769 drivers that I find in this link: Software Support of Boot Camp 5.1.5769.) (Note: this driver is material specific only works for my iMAC model). Once you have downloaded it, copy the two files in the root directory of the USB installation to replace the original ones. It's specific and material available for download somewhere on the Apple Site.
-From the Finder, delete the $WinPE$ and the Boot Camp of the FLASH PLAYER files.
-Expand the old drivers for Boot Camp 5.1.5769 (two records and another file) on your desktop.
-Copy the $WinPE$ and records of Boot Camp in the FLASH PLAYER.
5. open Boot Camp Assistant again and only select the third option, install Windows 7.
It will show you the screen to select what installation disk, select HARD drive.
Then drag the slide bar to select the size of the Bootcamp partition for windows you want, knowing that there is a restriction for windows installed using training camp on a MAC that the last byte of the BootCamp partition must reside in the first byte of the 2.2 T of each physical hard drive.
For my case, I need only 500G for bootcamp and leaving behind 1.7 to for my MAC OSX partition immediately after the bootcamp partition and an another 0.8 T MAC OSX partition after him. 1.7 TB and the partition of MAC OS x 0.8 TB well exploited in the meantime bootcamp partition, will be merged into a fusion drive by Bootcamp. Thus, you will end up with total 2.5 TB of disk space in a logical drive - fuser.
Go to this link for more details on this subject: n-on-a-3-tb-fusion-drive http://twocanoes.com/winclone/support/installing-windows-on-a-boot-camp-partitio
6. continue the process to partition the hard drive, then it will restart automatically in windows installation mode, install windows.
7. once the installation is complete, check that windows is functioning correctly.
E. Si you want to upgrade to windows 10 Windows 7.
1 if you plan to upgrade to windows 10, you'll find that the windows IE v.8 7 is no longer works and had many problems to load the page. Then when you try to download the latest version of Internet Explorer, you get an error that you need at least windows 7 SP1 to support the last IE. Life is too complicated, just download the google Chrome browser, then search for download windows 10 and then run the Microsoft valuation tool to upgrade.
2 but before upgrade you, unplug all your MAC USB drives, otherwise, you will find that, after having spent an hour downloading the windows 10 software, the upgrade will fail with the error "/ dynamicupdate...» ». It is an inexplicable mistake that no one seems to understand why. There are articles with proven results that the removal of all USB drives before running the windows 10 upgrade tool will correct this problem.
F. reinstall OSX El Capitan
Once your target windows system (if windows 7, windows 8 or windows 10) works very well. You can continue to create again your Fusion drive and reinstall OSX El Capitan.
1. Insert the install of OSX Yosemite rear USB to the iMAC, and then select Restart Windows, or stop, and then turn the MAC once again.
2. When you hear the ringing tone, press on and hold down the option key for 10 seconds. Then you release.
3. on the selection screen, select start Yosemite OSX install drive.
4. after starting, do not proceed to install OSX El Capitan again. But select Terminal from the menu bar.
5. in the terminal, type the command 'diskutil list cs' and you should see nothing to prove that there are no existing fusion drive yet.
6 type the 'diskutil list' command to list all disks and partitions.
The SSD has two partitions, the/dev/disk0s1 of EFI (209 MB) partition and the other/dev/disk0s2 of OSX partition we created in step B above, called SSD around 121 G.
The HARD drive has two partitions, the/dev/disk1s1 of EFI (209 MB) partition and the other/dev/disk1s2 of OSX partition we created in step B above, called SSD.
G. delete the logical storage of nucleus on the HARD disk drive and it refuses with the DSS to form a merger with faster performance disc
1. Insert the install of OSX El Capitan rear USB to the iMAC, and then select Restart Windows, or stop, and then turn the MAC once again.
2. When you hear the ringing tone, press on and hold down the option key for 10 seconds. Then you release.
3. on the selection screen, select start Yosemite OSX install drive.
4. after starting, do not proceed to install OSX El Capitan again. But select Terminal from the menu bar.
5. in the terminal, type orders for (to show what are the logical volume group ID and the ID of the logical Volume of the logical drive). You should see the logical volume to basic storage group created using two partitions on the hard drive, 1.7 TB and TB 0.8 created when we run the Yosemite Bootcamp to install windows.
Cs diskutil list
6. in the terminal, type commands to delete logical drives from basic storage. Note: All data will be destroyed in the logical drive.
diskutil cs deleteVolume Logical Volume ID
CS diskutil remove logical Volume Group ID
7. tap "diskutil list" command lists all the resulting partitions. You should see that the HARD drive has the following partitions.
/ dev/disk0 (internal, physical):
#: NAME SIZE TYPE IDENTIFIER
0: GUID_partition_scheme * GB 121,3 disk0
1: disk0s1 EFI EFI 209.7 MB
2: Apple_HFS GB SSD 121.0 disk0s2
/ dev/disk1 (internal, physical):
#: NAME SIZE TYPE IDENTIFIER
0: GUID_partition_scheme * 3.0 to disk1
1: EFI EFI 209.7 MB disk1s1
2: Apple_HFS 1.7 Untitled TB disk1s2
3: disk1s3 Apple_Boot Recovery 650.0 MB HD
4: Microsoft database BOOTCAMP 503.0 GB disk1s4
5: Apple_HFS 801,4 Untitled GB disk1s5
8 type the following commands to create the logical volumes group, named "myLVG" (or the name) of fuser using the usable for OSX to the SSD and HDD partitions.
diskutil cs to create "myLVG" disk0s2 disk1s2 disk1s5
Note: Mark the group id of logical volume shown in the results.
In my case, I want to book the last partition as standalone partition disk1s5 no-fusionend, so I can use it to raise the back, or format it in FAT32 to allow the exchange of data between the MAC and boot camp.
So, I do not understand this last partition in the drive of the merger. in my case, the command that I used is: diskutil cs to create "myLVG" disk0s2 disk1s2
9 create logical volumes named "Macintosh HD" (or you call it) on the logical volume group we just created for the reader of the merger.
diskutil createvolume logical volume group ID jhfs cs + 'Macintosh HD' 100%
10 command "diskutil cs type list" to check the resulting fusion drive created.
CoreStorage groups of logical volumes (1 found)
|
+ Logical Volume - Group F53C7A25-C2F3-4997-91E9-2E6B6BAB2E0E
=========================================================
Name: LVG
Status: online
Dimensions: 1815635525632 B (1.8 to)
Free space: 90112 B (90.1 KB)
|
+-Physical volume E176873C-7C80-4759-8110-BA7307E0C4B3
| ----------------------------------------------------
| Index: 0
| Disc: disk0s2
| Status: online
| Dimensions: 120988852224 B (121.0 GB)
|
+-Physical volume 6535AC3C-DCF8-453F-AD47-98905538386E
| ----------------------------------------------------
| Index: 1
| Disc: disk1s2
| Status: online
| Dimensions: 1694646673408 B (1.7 to)
|
+--> Logical volume family F3D15F87-FB84-4B43-B2F2-E9EACC7C42D9
----------------------------------------------------------
Encryption type: no
|
+--> Logical volume 0D807F6E-FB7C-418F-AAF4-EF3EA3525D10
---------------------------------------------------
Disc: disk2
Status: online
Size (Total): 1809780178944 B (1.8 to)
Reversible: no
Name: Macintosh HD
Volume name: Macintosh HD
Content indicator: Apple_HFS
LVG Type: Fusion, sparse
11 exit the terminal, go back to OSX El Capitan install screen and select the name of the fuser unit 'Macintosh HD' proceed to begin the installation of the os x for installation.
12. There will be a step in the installation ask you if you want to configure as a new computer, or restore from a time machine previous backup. Make your own choices it accordingly.
13 once OSX El Capitan has been installed and you have finished restoring the data and custom configurations, you can enter the application of preferences to check if you see the icon of the "Startup" disk", and if you choose Startup BootCamp in the next reboot, you should be able to boot up to Windows without pressing and holding the button option when reboot and choose to start windows manually. Also, in windows, you should be able to click on the bootcamp Control Panel and select for a startup to OSX on the next reboot.
14. one thing to be aware, if you install bootcamp in this way, the boot camp and the GUI utility disk in OSX El Capitan will not be able to adjust your settings. This means, if you need to touch anything or to readjust the size of the partition, you will need to do it again in step A. Alternatively, some how to get started with installing Mac OSX Yosemite USB, then adjust the partitions using similar commands shown in this article or other articles in this community.
15. yet once please take personal responsibility on damage if you follow the instructions in this article.
-
How can I fix a customer Launcher.exe gambling problem which could cause it to stop working?
The Client Launcher has no openings of the problem and update games reviews, events and the server info maint. etc., by clicking on the game where is installed the client takes me to this start page of games. But that's all. From there, I click the START GAME button and immediately the Game Launcher stops working. Then the pop-up message running runs saying A problem with launcher did stop working. This problem report has been sent to Microsoft. The Windows notification Qmessage closes leaving the Message of Microsoft Windows. Says that Microsoft will inform me with a solution when it becomes available.
In courses now since mid October 2010 and the problem is still a problem. Here are the details of what I tried.
Solutions provided by the Support Help Desk game still worked so let my forced. and still in treatment.
I completely uninstalled and reinstalled the game client and game more then enough time and that did not help. Even tried mirror download sites.
Windows Vista is up to date, the hardware and the drivers are all up to date. System requirements to run the game is ok. (I triple checked cause the game worked initially.) I could even play other games in the game Client. One day, while he was playing in the game he closed and stopped working. A bit like you have been started from the server). Since I could open the client and click on a game to see. clicking on start game triggers the Launcher of client to stop working.
I cleaned up my registry and it fixed and did a cleaning disc.
I read every help file in the hope of finding something or something, anything that would be useful. Impossible to find a solution.
I used the recording of events where there is a link Option to support for the error that occurred dansMon event systems online. There was no solution available.
I have reviewed the troubleshooting on the Microsoft TechNet site. Cannot find the fix there either.
I've exhausted all my resources I can think.
So if there is someone who can help me solve this problem once and for all, my son and I'd love to hear from you.
Thank you...
whoknowsu...
Hello
Please try to install the game in compatibility mode. Here is some information that can be very practical...
http://Windows.Microsoft.com/en-us/Windows-Vista/make-older-programs-run-in-this-version-of-Windows
http://Windows.Microsoft.com/en-us/Windows7/make-older-programs-run-in-this-version-of-Windows
-Check the functionality of the game under a spare user account
Uninstall/reinstall the program
-Clean Boot http://support.microsoft.com/kb/331796
I hope that this information is beneficial.
Thank you
Aaron
Microsoft Answers Support Engineer
Visit our Microsoft answers feedback Forum and let us know what you think -
has had to change the password; Unable to add music to the playlist; can't burn music on the disc.
problems with iTunes. Failed to add songs to the playlist. can't burn music on the disc; Message (wait 90 days for download purchases). another received message (unauthorized; "I have not authorized and renewed). Did not help.
I have 2 iPads, 1 iPhone and iPod touch, so I need iTunes to synchronize. I'd like a different music player.
Hello
The problems you describe can be caused by outdated software.
Make sure that iTunes and OS X are up-to-date.
On your open the App Store, and select updates from the menu.
On your iOS devices, tap settings > general > software update
-
A key using self-powered USB causes the base station go "off-line".
I found that by using a USB drive self-powered, as the WD My Passport, without a USB powered, hub attached to the base of the station USB port has caused the base station go "off-line". In fact, using a powered hub does not always remedy the situation, but it is more reproducible without one.
This is true for the AirPort Extreme and Time Capsule 802.11ac. The problem does not occur immediately, but it may happen over several days. The symptom is that the player is no longer lies in the Finder, or the base station appears in AirPort Utility.
My question is if others have had the same results? ... and did you find permanent solutions?
USB key "seems" less reliable on the airports of AC model than on previous versions.
I tend to not use USB attached to routers because I think it's convenient mediocre and poor speeds. But I tested with previous models, and it seems ok...
KT those a few posts here a me trial there. These are not self powered readers... who I have long recommended people avoid the use (without a powered hub)...
Re: External backup drive down regularly
In fact, the wire is different from what I remember... Age don't you know.
But I did the test on an AC TC. The result has been very reliable. He did not cause the TC to close... but I lost the connection of the USB almost every day... except for a trial where I kept the USB drive mounted in the Finder... so that the USB drive wouldn't turn it down. He then worked for a few weeks... until what the noise of rotation of disk (sitting next to me) drove me crazy... as soon as he was mounted is more, he would pass the same existence as before.
The previous model TC was barely big enough for the internal use of the power supply units. So powered car running disc was impossible.
Provide EI (GEN 1-5) at 1. 8A and 12v was adequate, but the standard USB port is estimated at 500 my wrong to manage disks free power.
You would certainly think AC 12v 5A power supply models would have a lot of power. Yet, power problems are a major problem still. Supply is extremely sensitive and stop easily for reasons I'm still to understand.
Where the long threads on power issues to the AE.
Now, I'm going to speculate... I think that SOME problems are associated with power.
What is the USB port side in airports of AC? Is it still 500ma? Apple never seem to give easy to find info on these details.
Do you know? I haven't measured it, but I can try timing the time it takes to charge a phone. Assuming that it will immediately trigger.
Then he will have problems with a self-powered drive. Even if the drive has less energy than quotes, current during starting is much higher. The restriction of the power on the USB port is managed by a self regulator recovery... Once you triggered it, you must stop the power... then reboot the machine to restore power.
Then, I also did the test with hub powered... and like your results... It was better. Longer time between the drive disappears from the network. But it was not enough to stop it.
There is another interesting effect using self-powered hubs... I discovered this on a computer running Mac OS lets say! The computer would not start with a powered hub connected to the front USB. Hubs self-powered cheap, showing a defect in their design. They can refer to the USB port. In this computer, it was enough to stumble on the good power circuit and prevent the supply, commissioning... As long as the computer is running, everything was fine... but if I turned off it would not start. I finally woke up I had to exit the USB every time. At one point, I made a "special" Cup USB cable 5v line so the hub can stay connected. You can probably just to isolate the 5v of contact in the USB. Regardless of the configuration of power USB in the AE or TC is as you can assume she's sensitive enough... and at any time when the 5V on USB hub exceeds the 5V in AE it could trigger.
The symptom is that the player is no longer lies in the Finder, or the base station appears in AirPort Utility.
Endangered of AU base station is not uncommon.
It responds to the pings? I guess he still has lights but is he blocked? You still get internet through it?
Try to open it manually in to THE... use of the file / configure from others and put the IP address of EI.
Talk with me by e-mail... It is open in the profile.
-
Satellite P775 stuck program on the use of the disc a vast
Hello
I have a strange problem on my laptop Toshiba Satellite P775 program with Windows 7.
The laptop boot from time to time, slow and heavy i/o operations (I can see it via the indicator disc to surveillance). Windows not crushed, but the heavy IO makes the laptop unusable.
Recently I reinstalled Windows (return to factory settings), but the issue has not disappeared.
A few words about 'stuck ':
1. once the laptop has been cooled for a long time - more than 1 hour - never occurs during initial start-up.
2. when a problem starts, it does not disappear after stopping and restarting the laptop
3 is coming during the connection process (stuck when connecting)
4. never happened to me when you work in "safe" mode
5. Windows not crushed, the mouse is generally sensitive - just very heavy and slow disk access makes virtually every application unusable.* The most recent research (quite shocking to me): once it goes all in running, I tried to unplug the power cord, then plug it in then after a few seconds. To my surprise, the "disruption" caused by the power connectivity - caused the laptop back to normal.*
No clue on how to debug and fix the problem?
Thanks for the care,
Max
Hello
In my opinion, there are different reasons for this.
First reason could be a large amount of processes that are running in the background
Theoretically, it could be possible that a process stresses the CPU and thus the performance of the laptop is slowing.
A HARD disk problem can cause this kind of problems too.
As you can see really hard to tell what could cause this problem.From my point of view, you should start by running processes.
Use check the CPU in the Manager of tasks (tab CPU) while this problem occurs. -
Disc tray is no longer fully opens, it stops before opening to halfway.
If I go out there, insert a disc and press again, the disc is recognized and the window will appear to the right of the screen asking what I want to do. By choosing "Run Autorun.exe" nothing happens.
By pressing the eject button, or by selecting "eject" after right click on the drive icon, causes the tray not opening only partially again.
The computer was bought nine of H.P. in January this year.
Is there anything I can do myself to fix the problem?
Equal rights of equal responsibilities.
Equal opportunities for equal capacities.It is under warranty. Please contact the Service from HP.
-
How to burn files to the disc of the retina macbook pro?
Hello. So I was wondering two things. One is how can I convert mov files to work on a disc on a dvd player to the TV. Second is how I just can burn retina macbook pro mov files because they do not come with a DVD player. I tried to use iDVD and iSkysoft DVD Creator, but they won't recognize the windows to mac dvd player thing. I did not blank discs their so I was wondering if it was a problem? Thank you.
One you get your iDVD project that you and ready to burn follow this workflow:
Once the project you want it save it as an image disk via the menu file → save as Disk Image . It will separate from the process of encoding of the burning process.
To check coding mount the disk image, launch a DVD player and read it. If it plays OK with DVD, encoding is good.
Burn burn to disc with utility disk or toasts to the slowest speed (2 x - 4 x) in order to ensure the best quality. Always use higher quality media: Verbatim, Maxell or Taiyo Yuden DVD-R are recommended in these forums.
Since you do not have an optical drive in your MBP you will need to copy the disk image file on a Mac that makes and burn from there with disk utility. Or you can get an external optical drive and use it to burn the disk with disk utility.
-
Setting up my HP Officejet 6500 has more the Question: first install the disc?
Hi all!
I was wondering if I should install the disc that came with my HP 6500 has more printer FIRST before connecting it to the top wireless? Or connect upward wireless first before installing the drive?
I saw somewhere where the plug & play when the connected printer caused some problems that did not accept the disc that came with the printer it seemed to replace the drive.
Any help would be appreciated before doing anything with the hook to the top of my new printer.
Thank you!
If you connect the USB printer that the answer is YES.
First run installation, during installation, you will be asked to connect the USB cable, then only, you need to connect.
Kind regards
Shlomi
-
Cannot read the disc for dragon 11, but will read and download dragon 9
I can install version 9 of Dragon, but when I tried to upgrade to Dragon 11, it wouldn't read the disc of Dragon 11.
I checked the disk on my laptop, and read 11 Dragon, she could not install the software for cause of memory.
Hello
· Another CD/DVD is getting recognized on the computer?
Here are a few options you can try:
1. you can download Dragon 11 on the manufacturer's Web site and try to upgrade.
Link for reference: http://shop.nuance.com/store/nuanceus/DisplayHomePage?resid=Tj5UDQoBAlYAAAT0MkUAAAAD&rests=1312707596649
2. install the application of the dish:
a. Insert the Setup on the laptop disk.
b. start Windows Explorer.
(c) in Windows Explorer, click to select the drive for the installation disc.
d. in the Edit menu, click Select all.
e. in the Edit menu, click on copy.
f. and paste it into an external USB drive or a USB flash drive.
g. plug in the drive to the computer where you want to install Dragon 11
h. on the file menu, point to new, click folder, type Setup 11 Dragon, and then press ENTER.
i. double-click the folder and then click on paste on the Edit menu.
j. double-click Setup.exe, and then follow the instructions that appear.
You can also access: how to troubleshoot common problems that occur when a Windows XP-based computer cannot read a CD or DVD: http://support.microsoft.com/kb/321641
-
Recently, I restarted my computer and received the following message is displayed:
"We apologize for the inconvenience, but Windows did not start successfully. A recent hardware or software change might have caused this.
If your computer stopped responding, restarted unexpectedly, or was automatically closed down to protect your files and folders, select last good known Configuration to return to the most recent settings that worked.
If a previous startup attempt was interrupted due to a power failure or because the Power or Reset button has been activated, or if you are not sure what caused the problem, choose Start Windows
Normally.Safe mode
Safe mode with networking
Safe mode with command promptLast good Configuration known (your most recent settings that worked) start Windows normally
Use top and down arrow keys to move the selection of your choice.
.
Seconds until Windows starts: 30 "After I tried all the options available, but whenever I do it, windows is only a blue Flash of a screen and then brings back me to the same menu over and over again.
I can NOT CONNECT AT ALL even in safe mode (by connection, I mean I can't access the section Office at all - case im explained does not this right). as soon as it reaches the load to windows xp my computer screen restarts as if I am the ' turn off and turn back on.
I tried to perform a repair of Windows through my cd of instalation installation, but it just took me a blue screen saying there was a problem and he had to shut down to avoid damage. He also told me this: * 0x0000000a (0x00000002, 0x00000000, 0 x 00000018, 0x80819b92)
The computer is an emachine and was purchased at a walmart nearly 5 years ago and it worked fine until one day it started to do this. I can't access any of my files or anything. It must be a software problem, because since then I checked all the problems of material possible and found nothing. the result of this is that I can't use my computer. It is a desktop computer and was reliable until it happened. I'm not sure of the cause, and I think it's something wrong with the operating system. I have tried everything I know and need help as soon as possible.
Hi josiahgenesis,
· Have you been able to launch the repair facility?
Try the following.
Method 1: Try to select disable automatic system failure reboot from the advanced boot menu options to see if it helps.
Method 2: Check to see if the following is useful.
You receive an error message "Stop 0x0000000A" in Windows XP
-
Not possible to burn a DVD-tells me that it cannot read the disc
What do I need to get windows or any other media player to burn a dvd movie cause that he told me that it can not read the disc. If someone can tell me what I please
The only version of XP that included the possibility of creating a
DVD-video is Windows XP Media Center Edition 2005.
What has been consulted through Windows Movie Maker and
was not shown to be extremely reliable.Beyond that... you need DVD Authoring software. The
following freeware is an example:(FWIW) It's always a good idea to create a system
Restore point before installing software or updates)DVD Flick
http://www.dvdflick.NET/Download.php
(the download is: "dvdflick_setup_1.3.0.7.exe")Save the file to a folder on your hard drive and
install from there.Be sure to read the Guide:
http://www.dvdflick.NET/Guide.phpTutorials:
Tutorial DVD Flick
http://beginwithsoftware.com/videoguides/DVD-flick-Guide.htmlBurn any Format video DVD PC
http://www.freevideoworkshop.com/dvdflicktutorial.htmTo create a video DVD base that should play in a free
permanent drive DVD... try the following...First... read the DVD Flick Guide to familiarize
with the program.Open DVD Flick and insert a blank DVD in your drive.
If the window of Autorun from your computer... just close it.
Click the project settings button and check... Video /.
Target format... residents United States... Choose... NTSC /.
Accept.The title button left click Add and navigate to your
Video clips and select the ones you want on the DVD.You can have by selecting one and then use
the up and down buttons.Left click on the button create DVD / OK / Yes / Yes.
Please wait while the DVD is created.
When the text "Completed successfully" is displayed you
DVD Flick can close. Now you can eject your DVD
and play in your DVD player.At some point you might want to buy more
Advanced Cyberlink, Nero, Roxio, software
Ulead, etc... but at least it is a start.Good luck.
Maybe you are looking for
-
Search menu drop down always on the top of the & blocks tapping annoyance of keyboard screen
Hello I use the windows on-screen keyboard 95% of the time. And I would usually place in the middle of the window when in use. When I need to type in the search box, and even if the screen keyboard it is set to always on top, it always goes IN the dr
-
No wireless - Satellite A60-106
HelloI model Satellite A60-106, and I was wondering if a wireless connection is enabled on the laptop, because it doesn't seem to work when I go to a WiFi active area. Thank you
-
I am on a trial with Acrobat Pro DC on a Mac and when I try to combine files for example a pdf file and a word doc it says "additional permissions to access to" the word doc, so I have to select a folder and grant access, etc. It's too long - is the
-
HelloI have a problem with the download. I want to download first pro demo, but after a few minutes, it shows me "update failed" and writes to me even when I want to update to Lightroom.Thank you
-
SpeedGrade - INTEL CPU is REQUIRED?
Looking at the Adobe "needed here basic configuration http://www.adobe.com/content/dam/Adobe/en/products/creativesuite/production/cs6/pdfs/adobe-mat item-performance-whitepap... .He suggests applications can run on a processor AMD EXCEPT Speedgrade?