CD/dvd cannot burn.

Similar Questions

• Program for creating Windows DVD cannot burn DVDs

  Program for creating Windows DVD cannot burn DVD due to can not find the DVD burner, free DVD burner disc see on the upper right. But my DVD drive with well with another burning program.

  Hello

  (1) have you made changes before the start of this issue?

  (2) you have the external devices connected to the computer?

  (3) what is the exact full error message?

  (4) is specific to the program the issue?

  Method 1: Clean boot

  How to set up Windows 7 to start in a "clean boot" State

  http://support.Microsoft.com/kb/929135

  Note: After a repair, be sure to set the computer to start as usual as mentioned in step 7 in the above article.

  Method 2: Resolution of the problems with creating a DVD-video using Windows DVD creation

  http://Windows.Microsoft.com/en-us/Windows7/troubleshoot-problems-with-creating-a-DVD-video-using-Windows-DVD-Maker

  For reference:

  DVD-video burning: frequently asked questions

  http://Windows.Microsoft.com/en-us/Windows7/DVD-Video-burning-frequently-asked-questions

  I hope this helps.

• MOVIES with the HELP of hp DVD CANNOT BURN a DH16AAL SCSI CdRom Device

  I can burn music and play music CDs, but can play any dvd any help please it tells me to insert the disc

  Besides the fact that you have posted in the wrong forum.  (A mod will be soon along move this thread).

  You describe the device as a DVD and CDRom.

  If the drive is a CD player, then the symptoms you describe to wait.  CD player will only recognize the DVD.

  However, your drive may not be a CDRom drive as you say you can burn CDs - a CDRom is unable to burn anything.

  It seems that you have a CD burner, which means that it won't recognize DVD.

  (A DVD burner can read/write CDs, but a CD burner can't read/write DVD)

• Satellite A80-129: Mat * a DVD - RAM UJ-830 s cannot burn DVDs

  MODEL: SA80-129
  DVD RAM TYPE MAST * A DVD-RAM UJ-830 S
  SYSTEM: WINXP
  SOFTWARE: NERO

  (1) DVDRAM CAN READ CD AND DVD EASILY, IT Burns CD WELL, BUT cannot burn DVDs, IT SHOWS: G:\ IS NOT ACCESSIBLE INCORRECT FUNCTION, UNTIL IT WORKS WELL. the blank dvd is not a problem, before I used even type a blank dvd to burn.
  (2) even allow the recoding in the properties, the properties shows the Virgin dvd 0bytes.

  all PROMTLY ANSWER would BE MUCH APPRECIATED.

  It doesn't sound good.
  I had a similar problem of combustion and the end of the story, I replaced the drive ;(
  However, try to remove the drive from Device Manager, and then again to restart the operating system should recognize the device again.
  Then you could check if it able to burn the DVD s s.
  I think you should also try burning different DVD media.

  I have visited many work sites and the reader, and especially the calibration lens malfunction could be responsible for burning problems.
  This could be a worst case and in this case, the replacement is necessary.

• Cannot burn DVDs on my Satellite C660

  I just bought a new complete Satellite C660 and I cannot burn DVDs.

  Tried to burn with the recovery media creator, Nero, IMGBurn and all fails at around 75%.
  When I tried to burn the recovery CD as I was asked that they have failed because of a problem STARTING...

  You can create DVDs from recovery use preinstalled Toshiba recovery media creator. Please test using DVD-R media.

  Have you tried using different media of high quality as TDK or Verbatim?

  Sorry, but this startup message said nothing to me. I've never seen something like this, even if I created several on several laptops Toshiba recovery disks.

• Cannot burn DVDs on Qosmio F10

  Hello

  I have very little success to burn a DVD.
  I'm using WIN DVD Creator and go through all the steps, but WIN DVD gives this message:
  The media cannot be deleted.

  I have no problem burning CD and DVD seems to be impossible. Any help out there?

  OLE

  Can I ask you what kind of DVD have you tried?
  It seems that you want to erase the DVD before burning. Have you tried to burn to DVD - RW?

• Cannot burn CDs or DVDs, get code error 380381-26-00037200

  Original title: DVD problem

  I can't burn a cd or a dvd, error code 380381-26-00037200 appears. CD DVD & cannot be formatted

  Try following the steps under "Windows 7 or Windows Vista" in the MS KB article:

  http://support.Microsoft.com/kb/982116

  These measures, to remove the UpperFilters and LowerFilters, values if they exist, in the registry key named can help.

  Create a System Restore Point beforehand and restart the computer later.

• Qosmio G20-127: after firmware update cannot burn CD or DVD

  I'm updating my firmware from F101 F102 to dvd so I can't copy any CD or DVD in my drive also some CD & DVD cannot be played after this update, I tried to
  install the old firmware F101, but I can't so please help me?

  Thanx

  Hello

  How do update you?
  Before update you the firmware, follow this:
  -Always use AC adapter to avoid a power off by updating the F / w.
  -Do not turn on DVD + r / + RW/RAM DRIVE by updating the F / w.
  -Put an end to all applications except the F/W update of the program.
  -Are not completed with force the F/W update program
  -Be sure to manually restart Windows after completing the update.
  -Update program automatically eliminates the ineligible disks

• Cannot burn DVD - R with my Satellite M70

  Hello
  I have a Toshiba Satellite M70-169 laptop which has the function
  DVD - R burning. However, when I insert a blank DVD - R, I have a
  message: drive inaccessible incorrect function.

  I think that just a fault of the computer notebook, or something else?
  Thank you.

  Hello

  Burning application you are using? Have you tried just preinstalled Sonic or same Nero?

  Generally avoid any problem. Please test with different applications, as well as with the different media (TDK, Verbatim, etc.).

• DVD writer is recognized but cannot burn files

  I am working on a friends computer and had to do a restore point to fix another problem.  After the restore point, everything works except the DVD/CD burner.  I can install a blank DVD or CD and Windows recognizes it and says I need to format it.  I have format it and give it a name and he accepts it. I put this drive on another computer, and it displays the name, I gave and I can use the disc in another computer.  I put the disc into his computer and it shows the disc with the name I gave to him, but I can't copy all of the files for it.  It does not show the ability to burn files when I select the files and if I try to copy or drag them to the DVD writer, nothing happens.  Paste function is grayed out when I select the DVD burner.  I can read files off other disks.  I tried to uninstall the DVD/CD player and reinstall the driver.  I uninstalled the IDE controller and reinstalled the driver.  Nothing seems to fix this.  The computer is an HP Pavilion Slimline s3200t with a built-in DVD/CD burner model HL-DT-ST DVD - RW GSA-H60L.  It runs Windows Vista Edition Home Premium with Service Pack 2. This drive was working properly before using the Restore Point.  I have not found any similar to this problem in the help forums.  Help, please.  Thank you.

  Work Yes, but does not properly. Visit the forums to Evan and try the above methods
  as sometimes running across these kick will begin a CD/DVD to work properly. As I said
  a CD/DVD is 4 disks 1 and one or several parts can fail separately from the rest.

  Have you recently added any software CD/DVD? What antivirus/antispyware/securiy programs have
  NEVER been on the system - these and the remains of those installed since may cause strange problems.

  Maybe a kind of corruption of the system:

  Follow these steps to remove corruption and missing/damaged file system repair or replacement.

  Run DiskCleanup - start - all programs - Accessories - System Tools - Disk Cleanup

  Start - type in the search box - find command top - RIGHT CLICK – RUN AS ADMIN

  sfc/scannow

  How to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe) program
  generates in Windows Vista cbs.log
  http://support.Microsoft.com/kb/928228

  Then, run checkdisk - schedule it to run at next boot, then apply OK your way out, then restart.

  How to run the check disk at startup in Vista
  http://www.Vistax64.com/tutorials/67612-check-disk-Chkdsk.html

  Rob Brown - MS MVP - Windows Desktop Experience: Bike - Mark Twain said it right.

• cannot burn DVD info

  my dvd player burner seems to be troubled. PC is 5 years old HP Pavilion a644p running 7 refurbed. He seems to want to, but it takes a long time to tell it aint going to do. Don't know if it's the drive or the media im trying to copy to.

  Sorry guys, just a bad batch of DVD blank

• DVD multi burner will work - Satellite M30X

  My laptop is Satellite M30x. My drive is a multi recorder, but my drive does not work properly. I can not burn DVD or CD, and I can't play some DVD. But I am able to read DVDs and CDs more.

  I tried upgrading the firmware from the driver download page, it won't work.

  How can I solve this problem?

  Thank you

  I guess the drive cannot burn DVDs, CD and cannot read some DVDs for some time.
  Am I wrong?
  It seems that the disk hardware is malfunctioning. In my opinion the lens do not calibrate properly and that's why the drive does not accept media most.

  Try following:
  -Remove the drive from the Device Manager and reboot the device. After restarting again the operating system must load the driver and should recognize the drive again. You can then check if it works.

  -In addition, you can physically remove the drive from the device and start windows. Then stops to the bottom of the laptop and install the drive again. After restarting again the laptop must load the firmware again and maybe he calibrates the new lens.

  But if such procedures don't help I think that you need to replace the unit.

• Satellite U505 - S2960 - drive external Supermulti cannot burn

  I use Satellite U505 - S2960 and I bought just driver Toshiba external supermulti for burning of jobs.

  After I connected the external hard drive, it can read DVD but cannot burn a DVD.
  The USB Sleep and Charge page always pop up the same I disable so I just uninstall.

  It seems that the problem is not there...
  I wonder how can I do my laptop to work with my new external dvd burner that is the same brand...

  Either way, I am using Windows 7

  Thanks in advance for any suggestions

  Hello

  What exactly is the problem?
  Why are you not able to write anything on a DVD? Do you get any error messages?

  Sleep function & load allows to recharge USB devices like mobile phones or other devices using the USB port even if the laptop is in sleep mode.

  I put t see a link between sleep & charge and external DVD drive

  By the way; What burning software do you use? I use Nero. For me the best burning software

• Satellite A40-231: SD-R6112 will not read the DVDs I burned

  I finally got my DVD burner to work, but now the drive will not read the DVDs I burned, which, of course, defies the point of having a dvd burner in the first place... When I insert my dvd recently burned, "working" light lights and stays on. Same thing happens no matter how many times I take it out and put plug back in, restart my computer, etc... any ideas anyone?

  Hello

  @Magnus:
  Sometimes, CDs and burned DVD cannot be read with no closing sessions of engraving. You should check this option.
  In addition, this burning program did you use?
  I use Nero. Form is the program better combustion and I never had a problem.
  What you need to do is to test several DVDs. not all media work on the disc.

• QSI CDRW/DVD SBW-242 won't read DVD or BURN a CD (music CD will PLAY) [AFTER the HD FORMAT and re - install}

  Dell Inspiron5100 WinXP SP3.

  Due to malware, I had to FORMAT my HD and re-install Windows XP OEM disc.  I also reinstalled WIN DVD4 from the OEM disc that came with the laptop.

  Check SYSTEM/DeviceMGR/material indicates a problem with the drive, but: it won't READ a DVD or burn a CD (which she has done before)

  Can't update anything of QSI as they were absorbed by COREL years.  No support available for WINDVD4

  When you try to run WINDVD4 with a DVD in the drive, I get a Popup of WINDVD screen that says:

  CREATE OVERLAY FAILED-Please lower your color depth or screen resolution and try again.  Of course, it worked fine with the reg settings in the past, now Ive tried even lower TWO the RES SCREEN and color at least registered but still does not work

  It WILL play CDs of music (mp3s)

  Found the following material etc.

  Provider: Microsoft Corp.

  File version: 5.1.2600.5512 (xpsp 080413-2108

  Driver date: 01/07/2001

  Driver version: 5.1.2535

  Driver files

  C\windows\system32\DRIVERS\cdrom.sys

  "" "" \DRIVERS\imapi.sys

  «"\DRIVERS\redbook.sys «»

  «"«\system32\ c:\windows\system32\storprop.dll»»»

  I installed and ran but it won't play MICROSOFT 'FIXIT' DVDs just run from WINDVD4 and still does not.

  FIXIT now brings me HERE

  It seems that FORMAT/reinstall has missed something the will allow the CD PLAYER of .1BURN and 2. READ the DVD, but allows you to PLAY CDs

  From: * e-mail address is removed from the privacy *.
  To: * e-mail address is removed from the privacy *.
  Date: Tuesday, May 17, 2011 08:30:29-0700
  Subject: QSI SBW 242 CDRW/DVD not play DVD or BURN a CD (music CD will PLAY) [AFTER the HD FORMAT and re - install}

  Response

  Hello

  1. are you able to read any type of file .doc or .txt of DVD?

  After following all the steps (including the update of the MP9 for Media Player [MP] 11) below

  I can get the drive to DISPLAY all the data from the DVD (Master & Commander 'movie)

  on-screen MP11.  He plays (automatically) the intro (ONLY) from the DVD music (as when you put it in a DVD player, forward to press PLAY) MP11 shows all of the content and all the files on the DVD and SEEMS ready to play, but pressing on PLAY don't either not anything.

  2 , what exactly happens when you try to burn the CD? You get the error message?

  Not nothing... He's here

  3. How do you try to burn CDs?

  MediaPlayer, selection of a track list, made a list of titles, and then click BURN... nothing happens

  4 have you tried to play the DVD content in ? windows media player

  I had not before, but now I have.  Previously it was default to my SELECTION WIN DVD4 as the DVD player (I think I've EVER SEEN the WINDVD format/start page on the front screen - it wasn't the default front DVD player either but don't remember what program PLAYS the DVD, he ' comes of ").  Now, go back and see 1. above for MP11 more details.

  Try to update the drivers of CD-RW/DVD drive and check. Also update the graphics driver.

  I did the entire bottom.

  1. click on Start, click Control Panel, and then double-click System.

  2 click on the hardware tab, and then click Device Manager.
  If you are prompted for an administrator password or for confirmation, type the password, or click continue.

  3 right-click on the CD-RW/DVD drive, and then select set to update driver.

  He asks if I have an OEM driver and / disk... NO.. I run the program through...

  "Hardware update Wiz can not find a better match the software installed"

  4. right click on the graphics card and select Update driver. »

  There is no "graphics card" on the material.  This machine has integrated graphics using a part of the main memory (or other) to run the video section:

  I find:

  AUDIO, VIDEO and GAME controllers (announcement)

  Audio codecs

  Audio drivers

  Legacy video capture device

  Media control devices

  Audio Sigma

  Video codecs

  All this seem normal but above I see YELLOW TWO warnings under 'OTHER DEVICES '.

  ?!  Ethernet controller "drivers for this divide (code28) is not installed.

  ?! VIDEO CONTROLLER (VGA Compatible) I didn't HAVE NO IDEA if THIS if APPLIES OR NOT

  Device type - other devices

  MFG-unknown

  Location PCI bus, device 0, function 0.  "Drivers for this device are not installed, CODE28 to reinstall the driver."

  Has been through the usual (request for drive... Laughing out loud. Impossible to beat")

  See also:

  How to troubleshoot common problems that occur when a Windows XP-based computer cannot read a CD or DVD

  http://support.Microsoft.com/kb/321641

  Did yesterday.  It installed/ran "MR. Microsoft Fixit' with the result:

  "Question: media in the CD-RW/DVD drive is not readable" CLICKED top DIFFICULTY... and after computer "worked" on this subject awhile, he says STATUS: fixed.  St ill did not.   MP9 introduced the format of the DVD player but don't seem to read anything other then showing a list:

  UNKNOWN

  Title 1

  Title2

  Title 3 etc., but could not do anything with this list.

  He appeared a box asking if I wanted to update my MP9... sure why not so I shut everything down and uninstalled 9 and installed Media player 11.

  Go BACK to # 1. now once again.  This is where I am.  MP11 shows all DVD data, the chart "the Album/DVD cover, all"titles"on the DVD, AND play the track audio 'intro' DVD but will not actually READ the DVD. "

  So far it's PROGRESS.  We are at a point where it SEEMS at least that we are ready to PLAY and MP can SEE all the info on the DVD.

  I see many people on other sites of the same question: Player does not work after FORMAT operating system and reinstall of WIN (and in my case: WinXP SP3 and WIN DVD4 of OEM disc)

  Thanks a lot for your help so far... I hope that we can get to the next step and get the reader of CD-RW/DVD on 'PLAY '.