CD/DVD drive is not detected or functional

Similar Questions

• Equium A200 - CD/DVD drive is not detected

  I can't open any CD/DVD disc. The drive is not detected.
  When checked in the management system, he demonstrated, the drivers are missing or corrupted.

  How do I download the drivers? Or is there another solution?
  My model number is PSAF5E
  Serial number is YT144538Q
  And the CD/DVD device is POLE * DVD / RAM UJ-850 s ATA device

  Hello!

  T, you can download or reinstall the CD/DVD driver because it s a part of the OS (operating system).

  It would be interesting if the BIOS can detect the drive. Please check this box.

  It would also be interesting if you have an error as the #19 error message. This is known and a search around the forum.

  Good bye

• My cd/dvd drive is not detected.

  CDDVD DRIVE IS NOT DETECTED

  A driver (service) for this device has been disabled.  Another driver can provide this functionality. (Code 32).

  Driver name: TSTTCORP CDDVDW TS-L633F

  Depending on the operating system, try following the steps under "Windows 7 or Windows Vista" or "Windows XP" in the MS KB article:

  http://support.Microsoft.com/kb/982116

  These measures, to remove the UpperFilters and LowerFilters, values if they exist, in the registry key named can help.

  Create a System Restore Point beforehand and restart the computer later.

• CD/DVD drive is not detected, the disc is missing or disconnected

  Well I have not tried to play anything or anything either burning on my laptop in a while and all of a sudden is not working more I followed suggestions on the microsoft site, but when I went into Device Manager to check on my drive anywhere it lists same CD-ROM/dvd-rom I'm so confused, I don't know what I tried to use microsoft not fixed and it's just as stuck as I am all he tells me it is than its disconnected or missing and cannot be found.

  Oh and while I'm asking questions my sound stopped working a few months back the small volume in the lower right corner icon has an 'x' next to him now and he says: no audio output device is installed, I tried following the suggestions online for this with no luck either. I hope that its not anything internal since I just had the motherboard replaced by a few months before this happened

  Thank you very much I hope you can help!

  Hello

  Well it still might be hardware or wiring.

  Restart to make sure that nothing is inteferring with the process.

  Step 1: Please make all underneath the same if you've done it before as it's often the total of the process which
  solves the problem.

  Try this - Panel - Device Manager - CD/DVD - double-click on the device - driver tab - click
  Update the drivers (this will probably do nothing) - then RIGHT click the drive - UNINSTALL - REBOOT
  This will refresh the default driver stack. Even if the reader does not appear to continue below.
  
  Then, work your way through these - don't forget the drive might be bad, could be a loose cable or
  slight corrosion on the contacts (usually for a laptop) and other issues.

  Your CD or DVD drive is missing or is not recognized by Windows or other programs
  http://support.microsoft.com/kb/314060 - a Mr Fixit

  The CD drive or the DVD drive does not work as expected on a computer that you upgraded to Windows Vista
  http://support.Microsoft.com/kb/929461

  When you insert a CD or a DVD, Windows Vista may not recognize the disc
  http://support.Microsoft.com/kb/939052

  Your CD or DVD drive cannot read or write media - A Mr Fixit
  http://support.Microsoft.com/GP/cd_dvd_drive_problems

  CD/DVD drive does not appear in Windows Vista, or you receive this error during the installation of Windows Vista after booting from the DVD (AHCI)
  http://support.Microsoft.com/kb/952951
  Drive CD - R or CD - RW Drive is not recognized as a recordable device
  http://support.Microsoft.com/kb/316529/

  Hardware devices not detected or not working - A Mr Fixit
  http://support.Microsoft.com/GP/hardware_device_problems

  Another possibility is that the cables are loose. Remove ALL power, then make sure that the cables in both
  ends. Remove and replace, do not just tight. For laptops, you can often clean power and
  contacts data with a pencil eraser.

  Some DVD players do not use the Windows default drivers so check with the manufacturer of system and
  manufacturer of device to see if there is a firmware or drivers for your drive if necessary.

  ===============================

  Step 2: You have disc problems as the CD/DVD is actually 4 discs in 1 case (CD & DVD burning and)
  Playback of CD and DVD). Therefore, it is not unusual for 1 or 2 rooms with not so work that others do it properly.

  Did you follow the Troubleshooting Guide for the reader who still does not work? There are some registry entries
  that the troubleshooter does not, and those who "could" be the cause.

  Check with your system manufacturer Maker and device for possible firmware updates and the good
  Your player registry entries.

  Here are the keys in my opinion, are those in question - for the reader of CD/DVD subkeys of course that he will be
  other subkeys in these keys. Be sure to ask specific keys involved as well as the parameters.

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Enum\IDE

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Hardware Profiles\0001\System\CurrentControlSet\Enum\IDE

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Class\ {4D36E965-E325-11CE-BFC1-08002BE10318}

  -----------------------------------------------------------------------

  You can probably find more info here and maybe even registry settings correct for your CD/DVD drive
  a person with the same model.

  Forums - a lot of expert real help
  http://Club.myce.com/

  CD/DVD units
  http://www.myce.com/storage/

  I hope this helps.
  Rob - bicycle - Mark Twain said it is good.

• CD/DVD drive is not detected (Windows Vista). Error message: Please insert a disk (removable disk): __Our device driver is: TSSTcorp CD/DVGW TS-H653L ATA Device.

  Was not aware there is a problem until I tried some recently audio and data CDs.  Have you tried different Web sites to help you, however some of the directions come with a warning that by following certain procedures I can create other problems.  The FixIt tool was not able to install the player.

  Hello

  Please ALL these even if you've done it before as it's often the total process that
  solves the problem. You should also check with the system manufacturer as some readers do not use windows
  by default the drivers and need their own, use the bottom and if no joy check on the site of the manufacturer of the system.

  Try this - Panel - Device Manager - CD/DVD - double-click on the device - driver tab - click
  Update the drivers (this will probably do nothing) - then RIGHT click the drive - UNINSTALL - REBOOT
  This will refresh the default driver stack. Even if the reader does not appear to continue below.
  
  Then, work your way through these - don't forget the drive might be bad, could be a loose cable or
  slight corrosion on the contacts (usually for a laptop) and other issues.

  Your CD or DVD drive is missing or is not recognized by Windows or other programs
  http://support.microsoft.com/kb/314060 - a Mr Fixit

  The CD drive or the DVD drive does not work as expected on a computer that you upgraded to Windows Vista
  http://support.Microsoft.com/kb/929461

  When you insert a CD or a DVD, Windows Vista may not recognize the disc
  http://support.Microsoft.com/kb/939052

  Your CD or DVD drive cannot read or write media - A Mr Fixit
  http://support.Microsoft.com/GP/cd_dvd_drive_problems

  CD/DVD drive does not appear in Windows Vista, or you receive this error during the installation of Windows Vista after booting from the DVD (AHCI)
  http://support.Microsoft.com/kb/952951
  Drive CD - R or CD - RW Drive is not recognized as a recordable device
  http://support.Microsoft.com/kb/316529/

  Hardware devices not detected or not working - A Mr Fixit
  http://support.Microsoft.com/GP/hardware_device_problems

  Another possibility is that the cables are loose. Remove ALL power, then make sure that the cables in both
  ends. Remove and replace, do not just tight. For laptops, you can often clean power and
  contacts data with a pencil eraser.

  Hope these helps.
  Rob - bicycle - Mark Twain said it is good.

• CD/DVD drive is not detected.

  For some reason my CD/DVD drive is more functional.  I can't even eject the disc that is in it and it does not recognize.  I have searched for corrections and so far all I've done was to remove the filter lower and upper filters in the registry.  I'll try to uninstall and reinstall this drive, but I can't even find on device manager

  Any help would be appreciated... Thank you!

  Here is the solution I mentioned earlier. Good luck and thank you Greg!

  I thought I had posted the solution.  The upper and lower filters need to be refreshed.  Here is a solution I found on the Adobe forums. http://kb2.Adobe.com/CPS/402/kb402306.html

  Refresh the CD and DVD drivers list in the Windows registry.

  Warning: The registry contains information on the system that are critical to your computer and applications. Before editing the registry, be sure to make a backup of it. Adobe does not provide support for problems that result from incorrectly modifying the registry. Adobe strongly recommends that you have experience editing system files before you modify the registry. For more information on the Windows Registry Editor, see the Windows documentation or contact Microsoft Technical Support.

  To refresh the CD and DVD drivers list in the Windows registry:

  Important: After you refresh the list of drivers in the Windows registry, you may need to reinstall any other CD or DVD on your computer to write applications. If you restart Windows after this procedure and other burning CD or DVD applications do not recognize the CD or DVD drive, and then reinstall those applications.

  1. Uninstall your Adobe application.
  2. Open the Registry Editor:
     • On Windows 2000 and XP: click Start > run. Type regedit in the box text open, and then click OK.
     • On Windows Vista: Click Start. Type regedit in the search text box, and then press ENTER.
  3. In the left pane of the registry editor, navigate to HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Class and select the {4D36E965-E325-11CE-BFC1-08002BE10318} key, which appears as a folder.
  4. Select file > export (Windows XP and Vista) or registry > export a file from the registry (Windows 2000).
  5. In the export registry file dialog box, select the branch selected under export range, name the file (for example, CDDVDkey.reg) and click Save to save the file to the desktop.
  6. In the Panel to the right of the registry editor, select the LowerFilters line, and then choose the editing command > delete. Click Yes in the dialog box confirm deleting key.
  7. Select the UpperFilters line, and then choose the editing command > delete. Click Yes in the dialog box confirm deleting key.
  8. Close the registry editor.
  9. Open the Device Manager:
     • On Windows 2000 and XP: click Start > Control Panel. Double-click the system icon, click the Hardware tab, and then click Device Manager.
     • On Windows Vista: Click Start > Control Panel, double-click System, and then click Device Manager in the task pane.
  10. Click on the symbol more then to CD-ROM/DVD-ROM drives.
  11. For each listed DVD-ROM or CD-ROM drive, select the icon then choose Action > uninstall.
  12. Restart Windows.
  13. Windows will automatically detect and reinstall your CD-ROM or DVD - ROM drives. You can check that the drives are installed in the device (see step 9) Manager. If the drives are not present, open Device Manager and choose Actions > Scan for hardware changes.
  14. Reinstall your Adobe application.
  15. Restart Windows.

  Important: If this solution doesn't solve the problem with the application you reinstalled, then you must restore the CD and DVD drivers list in the Windows registry.

  To restore the exported CD and DVD drivers list:

  1. Double-click the registry key that you exported.
  2. Close the registry editor.

  3. Restart Windows.

  • Proposed as answer byGreg good and Cool Sunday, May 16, 2010 11:38

• DVD drive does not detect DVD satellite 1900-303

  My CD-RW/DVD drive refuses to read DVDs, acting as if there is no disc in the drive, no matter what I try. I have not used the machine regularly in a while and just starting to discover this.

  It also has a problem with burning discs, if it is of no interest. I bought a lens cleaner, but it won't work because the laptop still does not recognize the disc. Also, I've never fiddled with the control of the region and have already tried reinstalling the driver, but to no avail.

  It's a S1900-303, the number of model PS192E-00G1N-EN.
  Any help that anyone can give is much appreciated, it's really annoying.

  Thank you very much.

  Hello guys

  First of all if there are problems with burning CD or DVD, you will need to test different CD or DVD. Not all CD or DVD is compatible and can be used in the drive.
  That's why check different CD/DVD from different manufacturers.

  But if the drive is not able to burn or play a CD/DVD, so I assume that the reader has a malfunction and only the replacement of the device could help.

  @Judith: unit you seems to be new and the guarantee must cover replacing the drive.
  But before you contact the ASP in your country, check the different media.
  In the user manual a list with compatible and tested the CD and the DVD.

• Why the CD/DVD drive is not detected by VISTA OS: laptop HP DV6000

  Tried the system restore, it will not be displayed.  BIOS shows is not the CD, but 'my computer '.  How can I get the CD/DVD to be detected by the operating system: VISTA Home Premium?

  Hello

  Try the microsoft 'fix - it' for your problem below

  http://support.Microsoft.com/mats/cd_dvd_drive_problems/en-us

  and read this information too

  http://support.Microsoft.com/kb/982116/en-us

• CD/DVD Rom drive - disk not detected when you try to play a movie or a cd.

  I tried everything in the book according to what the technical support guy me to HP.  Gave me a new optical drive.  I made the purchase and asked the guy.  How do I get the driver if it does not appear in my device manager?  He said just to install the new optical drive, and it will download automatically.  Yes, it was the most ridiculous thing.  He did his best to convince me.  Now, I received the new optical drive and even absurdity.  It won't work.  Try to get assistance and spend hours on the phone with them and no one can help me.  Wow.  Scam, scam, I don't really know what to call it.

  Hello

  Maybe it wasn't the drive first:

  Step 1: Please do all the same underneath if you did some before as is often total
  a process that solves the problem.

  Try this - Panel - Device Manager - CD/DVD - double click on the device - driver tab.
  Click on update drivers (this will probably do nothing) - RIGHT click ON the drive - uninstall.
  RESTART this will refresh the default driver stack. Even if the reader does not appear to continue
  below.
  
  Then, work your way through these - don't forget the drive might be bad, could be a coward
  cable or slight corrosion on the contacts (usually for a laptop) and other issues.

  Your CD or DVD drive is missing or is not recognized by Windows or other programs
  http://support.microsoft.com/kb/314060 - a Mr Fixit

  Try this fix manually if the Fixit 314060 does not work
  http://www.pchell.com/hardware/cd_drive_error_code_39.shtml

  Your CD or DVD drive is missing or is not recognized by Windows or other programs-
  a Mr Fixit
  http://support.Microsoft.com/kb/982116

  The CD drive or the DVD drive does not work as expected on a computer that you upgraded to
  for Windows Vista
  http://support.Microsoft.com/kb/929461

  When you insert a CD or a DVD, Windows Vista may not recognize the disc
  http://support.Microsoft.com/kb/939052

  Your CD or DVD drive cannot read or write media - A Mr Fixit
  http://support.Microsoft.com/GP/cd_dvd_drive_problems

  CD/DVD drive does not appear in Windows Vista, or you receive this error in Windows
  Vista installation after booting from the DVD (AHCI)
  http://support.Microsoft.com/kb/952951
  Drive CD - R or CD - RW Drive is not recognized as a recordable device
  http://support.Microsoft.com/kb/316529/

  Hardware devices not detected or not working - A Mr Fixit
  http://support.Microsoft.com/GP/hardware_device_problems

  Another possibility is that the cables are loose. Remove ALL power, then make sure that the cables in both
  ends. Remove and replace, do not just tight. For laptops, you can often clean power and
  contacts data with a pencil eraser.

  Some DVD players do not use the Windows default drivers so check with the manufacturer of system and
  manufacturer of device to see if there is a firmware or drivers for your drive if necessary.

  ===============================

  Step 2: You have disc problems as the CD/DVD is actually 4 discs in 1 case (CD & DVD
  Burn and CD and DVD read). So it is not unusual for 1 or 2 operational so that other parts
  do it right.

  Did you follow the Troubleshooting Guide for the reader who still does not work? There are
  the entries in registry that the troubleshooter does not solve and those who "might" be the cause.

  Check with your Maker system and a device for the two possible firmware updates and
  the correct registry entries for your car.

  Here are the keys that I of course are those in question - for the subkeys of the CD/DVD drive
  as there will be other subkeys in these keys. Do not forget to ask specific keys involved as well as
  the parameters.

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Enum\IDE

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Hardware Profiles\0001\System\CurrentControlSet\Enum\IDE

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Class\ {4D36E965-E325-11CE-BFC1-08002BE10318}

  -----------------------------------------------------------------------

  You can probably find more info here and maybe even the exact registry for your CD/DVD settings
  drive from someone with the same model.

  Forums - a lot of expert real help
  http://Club.myce.com/

  CD/DVD units
  http://www.myce.com/storage/

  Use DevManView to locate the CD/DVD in the registry (be careful and do a prior Restore Point)
  nothing change) - find the DevManView device and then make a right click on it free in RegEdit.

  DevManView - free - an alternative to the standard Windows Device Manager, which displays all the
  devices and their properties in flat table, instead of the tree viewer
  http://www.NirSoft.NET/utils/device_manager_view.html

  I hope this helps.

  Rob Brown - MS MVP - Windows Desktop Experience: Bike - Mark Twain said it right.

• My CD/DVD drive will not appear in the Device Manager, but present in the BIOS.

  DevCon didn't find it. It will not open even if I don't get to Device Manager and check for changes to the system. I deleted the registry entries upper and lower limit. Any other suggestions? For additional emphasis, he does not show even in the Manager of devices so I cannot restore or reinstall the drivers from there. It might also help that I use Vista Home Premium on a Compaq Presario F755us.

  Hello

  (1) does the BIOS see the main hard disk drive or a secondary hard drive?

  (2) remember to make changes to the computer before the show?

  You know may not be not that most systems are set to show only the splash screen. If you go into the BIOS Setup, it should show the disks that have been detected on two primary and secondary IDE channels.

  Note: the basic procedure to change the setting of the disk controller is to restart your computer and enter the system BIOS. The most common method is to press F2 to enter Setup, (another PC may use a different key). On the BIOS screen, find the setting that offers the AHCI, ATA or IDE and RAID. If the parameter is set to AHCI, change the setting to ATA. Restart the PC on the Windows installation disc

  Warning: Incorrect settings in the system BIOS can cause your PC function incorrectly. If you are not familiar with the configuration of the BIOS of the system, you must contact the PC manufacturer for assistance.

  Try the steps in the following article and check if it helps.

  My drive does not appear in Windows Explorer

  http://support.Microsoft.com/kb/330140

  Registry warning: Important this section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base: http://support.microsoft.com/kb/322756/

  You can also check the following items.

  CD drive or the DVD drive does not work as expected on a computer that you upgraded to Windows Vista: http://support.Microsoft.com/kb/929461

  Error: A required CD/DVD device driver is missing - when you boot Windows 7 or Windows Vista installation disk: http://support.microsoft.com/kb/952951

• Toshiba cd/dvd drive will not read or eject or anything like that!

  Cd/dvd driver for my Toshiba laptop will not work. It lasted about a year, then he became gradually sporadic to read/write or ejection and by last winter, he stopped all together. I've uninstalled and reinstalled the drivers for it, and in Device Manager, it says that the device is functioning normally; every once in a blue moon it will suddenly eject, but then if you put something in nothing happens, even not with the original disks. With the repair utility, it says something like unreadable media, at best. I'm a little confused as to what is happening here, so, what steps should I take to verify if it is indeed the drive disc or something in the software?

  Thanks, Bruce

  Hello

  You may need to check with Toshiba Support, documentation online & drivers and their forums
  for problems known.

  Toshiba - Forums
  http://laptopforums.Toshiba.com/

  Toshiba - Contacts
  http://www.CSD.Toshiba.com/cgi-bin/TAIS/support/JSP/navShell.jsp?CF=su_contact

  Toshiba - drivers - access your model
  http://www.CSD.Toshiba.com/cgi-bin/TAIS/support/JSP/home.jsp?NAV=download

  Toshiba - Support
  http://www.CSD.Toshiba.com/cgi-bin/TAIS/support/JSP/home.jsp

  --------------------------------------------------------------------------------------------------------

  Step 1: Please do all the same underneath if you did some before as is often total
  a process that solves the problem.

  Try this - Panel - Device Manager - CD/DVD - double click on the device - driver tab.
  Click on update drivers (this will probably do nothing) - RIGHT click ON the drive - uninstall.
  RESTART this will refresh the default driver stack. Even if the reader does not appear to continue
  below.
  
  Then, work your way through these - don't forget the drive might be bad, could be a coward
  cable or slight corrosion on the contacts (usually for a laptop) and other issues.

  Your CD or DVD drive is missing or is not recognized by Windows or other programs
  http://support.microsoft.com/kb/314060 - a Mr Fixit

  Try this fix manually if the Fixit 314060 does not work
  http://www.pchell.com/hardware/cd_drive_error_code_39.shtml

  Your CD or DVD drive is missing or is not recognized by Windows or other programs-
  a Mr Fixit
  http://support.Microsoft.com/kb/982116

  The CD drive or the DVD drive does not work as expected on a computer that you upgraded to
  for Windows Vista
  http://support.Microsoft.com/kb/929461

  When you insert a CD or a DVD, Windows Vista may not recognize the disc
  http://support.Microsoft.com/kb/939052

  Your CD or DVD drive cannot read or write media - A Mr Fixit
  http://support.Microsoft.com/GP/cd_dvd_drive_problems

  CD/DVD drive does not appear in Windows Vista, or you receive this error in Windows
  Vista installation after booting from the DVD (AHCI)
  http://support.Microsoft.com/kb/952951
  Drive CD - R or CD - RW Drive is not recognized as a recordable device
  http://support.Microsoft.com/kb/316529/

  Hardware devices not detected or not working - A Mr Fixit
  http://support.Microsoft.com/GP/hardware_device_problems

  Another possibility is that the cables are loose. Remove ALL power, then make sure that the cables in both
  ends. Remove and replace, do not just tight. For laptops, you can often clean power and
  contacts data with a pencil eraser.

  Some DVD players do not use the Windows default drivers so check with the manufacturer of system and
  manufacturer of device to see if there is a firmware or drivers for your drive if necessary.

  ===============================

  Step 2: You have disc problems as the CD/DVD is actually 4 discs in 1 case (CD & DVD
  Burn and CD and DVD read). So it is not unusual for 1 or 2 operational so that other parts
  do it right.

  Did you follow the Troubleshooting Guide for the reader who still does not work? There are
  the entries in registry that the troubleshooter does not solve and those who "might" be the cause.

  Check with your Maker system and a device for the two possible firmware updates and
  the correct registry entries for your car.

  Here are the keys that I of course are those in question - for the subkeys of the CD/DVD drive
  as there will be other subkeys in these keys. Do not forget to ask specific keys involved as well as
  the parameters.

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Enum\IDE

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Hardware Profiles\0001\System\CurrentControlSet\Enum\IDE

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Class\ {4D36E965-E325-11CE-BFC1-08002BE10318}

  -----------------------------------------------------------------------

  You can probably find more info here and maybe even the exact registry for your CD/DVD settings
  drive from someone with the same model.

  Forums - a lot of expert real help
  http://Club.myce.com/

  CD/DVD units
  http://www.myce.com/storage/

  Use DevManView to locate the CD/DVD in the registry (be careful and do a prior Restore Point)
  nothing change) - find the DevManView device and then make a right click on it free in RegEdit.

  DevManView - free - an alternative to the standard Windows Device Manager, which displays all the
  devices and their properties in flat table, instead of the tree viewer
  http://www.NirSoft.NET/utils/device_manager_view.html

  I hope this helps.

  Rob Brown - MS MVP - Windows Desktop Experience: Bike - Mark Twain said it right.

• Media in the CD/DVD drive is not readable

  Media in the CD/DVD drive is not readable (Optiarc DVD RW AD-) 7561 ATA Device responding drive is empty or the media format is not supported

  WINDOWS VISTA HOME PREMIUM SERVICE PACK 2

  RANGE OF COMPAQ PRESARIO CQ61 NOTEBOOK PC

  • My laptop can read the DVD, but it will not read I try to play any CD. It will be still asking to insert the disc when I.
  • See below the report of Mr. Microsoft Fix

  I appreciate your help with this. Thank you

  Problems found
  Media in the CD/DVD drive is not readable (Optiarc DVD RW AD-) 7561 ATA Device Media in the CD/DVD drive is not readable (Optiarc DVD RW AD-) 7561 ATA Device The drive is empty or the media format is not supported	Not fixed
  Insert the decipherable by media Failed

  Verified issues
  Class filter drivers are corrupt Class filter drivers are corrupt One or more specific class filter drivers are missing/corrupted	Checked
  Filter of device drivers are corrupt (Optiarc DVD RW AD - 7561 ATA Device) Filter of device drivers are corrupt (Optiarc DVD RW AD - 7561 ATA Device) One or more device-specific filter drivers are missing/corrupted	Checked
  Device is not working properly (Optiarc DVD RW AD - 7561 ATA Device) Device is not working properly (Optiarc DVD RW AD - 7561 ATA Device) This device is faced with a problem that it prevents to function properly	Checked
  Drive is disabled (Optiarc DVD RW AD - 7561 ATA Device) Drive is disabled (Optiarc DVD RW AD - 7561 ATA Device) The CD/DVD drive have been disabled in Device Manager	Checked
  Drive is not assigned a drive letter Drive is not assigned a drive letter The CD/DVD drive is not accessible via a drive letter assigned	Checked

  Problems found	Details of detection
  6 Media in the CD/DVD drive is not readable (Optiarc DVD RW AD-) 7561 ATA Device Not fixed
  The drive is empty or the media format is not supported
  Insert the decipherable by media Failed Insert a CD or a DVD disc play in the selected CD/DVD drive
  Verified issues	Details of detection

  6 Class filter drivers are corrupt Checked

  One or more specific class filter drivers are missing/corrupted

  Fix class filter drivers Not work   Remove references to class filter missing/corrupt driver

  6 Filter of device drivers are corrupt (Optiarc DVD RW AD - 7561 ATA Device)

  Checked

  One or more device-specific filter drivers are missing/corrupted

  Uninstall the device Not work

  Uninstall the device problem

  6

  Device is not working properly (Optiarc DVD RW AD - 7561 ATA Device)

  Checked

  This device is faced with a problem that it prevents to function properly

  Rescan devices Not work

  Look for changes in available devices

  Uninstall the device Not work

  Assign drive letters to all the readers who have no drive letter

  6 Drive is disabled (Optiarc DVD RW AD - 7561 ATA Device) Checked

  The CD/DVD drive have been disabled in Device Manager

  Turn on the device Not work   The device must be activated before it can be used

  6 Drive is not assigned a drive letter Checked

  The CD/DVD drive is not accessible via a drive letter assigned

  Drive letter Not work   Assign drive letters to all the readers who have no drive letter

  Hello

  Well you have studied the issues pretty well. Could be material.

  You have disk problems as the CD/DVD is actually 4 discs in 1 case (CD & DVD burning and)
  Playback of CD and DVD). So it is not unusual for parts from 1 or 2 to not work so that others do
  correctly.

  A CD/DVD cleaner might help.

  CD have a tolerance + - and your must read on the edge outside these tolerances of discs.
  They may be delivered, but it is generally more economical to replace the disk.

  Several good info here:
  http://Club.myce.com/

  CD/DVD units
  http://www.myce.com/storage/

  Notes on the troubleshooting and repair of readers of compact disks and CD-ROM Drives
  http://www.repairfaq.org/repair/F_cdfaq7.html#CDFAQ_014

  ============================================

  Step 1: Please do all the same underneath if you did some before as is often total
  a process that solves the problem.

  Try this - Panel - Device Manager - CD/DVD - double click on the device - driver tab.
  Click on update drivers (this will probably do nothing) - RIGHT click ON the drive - uninstall.
  RESTART this will refresh the default driver stack. Even if the reader does not appear to continue
  below.
  
  Then, work your way through these - don't forget the drive might be bad, could be a coward
  cable or slight corrosion on the contacts (usually for a laptop) and other issues.

  Your CD or DVD drive is missing or is not recognized by Windows or other programs
  http://support.microsoft.com/kb/314060 - a Mr Fixit

  Try this fix manually if the Fixit 314060 does not work
  http://www.pchell.com/hardware/cd_drive_error_code_39.shtml

  Your CD or DVD drive is missing or is not recognized by Windows or other programs-
  a Mr Fixit
  http://support.Microsoft.com/kb/982116

  The CD drive or the DVD drive does not work as expected on a computer that you upgraded to
  for Windows Vista
  http://support.Microsoft.com/kb/929461

  When you insert a CD or a DVD, Windows Vista may not recognize the disc
  http://support.Microsoft.com/kb/939052

  Your CD or DVD drive cannot read or write media - A Mr Fixit
  http://support.Microsoft.com/GP/cd_dvd_drive_problems

  CD/DVD drive does not appear in Windows Vista, or you receive this error in Windows
  Vista installation after booting from the DVD (AHCI)
  http://support.Microsoft.com/kb/952951
  Drive CD - R or CD - RW Drive is not recognized as a recordable device
  http://support.Microsoft.com/kb/316529/

  Hardware devices not detected or not working - A Mr Fixit
  http://support.Microsoft.com/GP/hardware_device_problems

  Another possibility is that the cables are loose. Remove ALL power, then make sure that the cables in both
  ends. Remove and replace, do not just tight. For laptops, you can often clean power and
  contacts data with a pencil eraser.

  Some DVD players do not use the Windows default drivers so check with the manufacturer of system and
  manufacturer of device to see if there is a firmware or drivers for your drive if necessary.

  ===============================

  Step 2: You have disc problems as the CD/DVD is actually 4 discs in 1 case (CD & DVD
  Burn and CD and DVD read). So it is not unusual for 1 or 2 operational so that other parts
  do it right.

  Did you follow the Troubleshooting Guide for the reader who still does not work? There are
  the entries in registry that the troubleshooter does not solve and those who "might" be the cause.

  Check with your Maker system and a device for the two possible firmware updates and
  the correct registry entries for your car.

  Here are the keys that I of course are those in question - for the subkeys of the CD/DVD drive
  as there will be other subkeys in these keys. Do not forget to ask specific keys involved as well as
  the parameters.

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Enum\IDE

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Hardware Profiles\0001\System\CurrentControlSet\Enum\IDE

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Class\ {4D36E965-E325-11CE-BFC1-08002BE10318}

  -----------------------------------------------------------------------

  You can probably find more info here and maybe even the exact registry for your CD/DVD settings
  drive from someone with the same model.

  Forums - a lot of expert real help
  http://Club.myce.com/

  CD/DVD units
  http://www.myce.com/storage/

  I hope this helps.

  Rob Brown - MS MVP - Windows Desktop Experience: Bike - Mark Twain said it right.

• Satellite 2430: CD/DVD drive does not work - i/o error

  Hello all Toshiba people.i have recently bought a Toshiba Satellite 2430 for a very good price. One thing the carpet * a DVD - ram Uj - 810 drive does not work when I put in any type of cd or dvd, I get this error
  F:\ is not accessible.
  The request could not be performed because of an i/o error.

  I talked to my local computer Wizz and does everything that he suggested to the letter and still the same problem. He suggested updating the bios drivers and the only way to do that is on a disk drive that she cannot take the an or a CD or dvd drive is not working. Can you please help me!

  Begging you a lot
  Michael Borger

  In my view BIOS update will not change.
  I assume that the reader has worked in the past with the same BIOS version
  It is a drive hardware problem or some registry keys are corrupt.

  I think that it s a hardware malfunction may be a matter of lenses.
  But try this;
  Remove the drive from Device Manager and shut the laptop computer. After restarting again the operating system should recognize the drive again. Then you can check the functionality.

  Otherwise, you can remove the disk from the laptop, and then start the laptop without the drive. Then stop the laptop, put the drive in the notebook and start over.
  The firmware should again loads.

  But if these procedures help t, I don t see it differently as for replace the drive

• CD/DVD drive does not read discs on Equium A100

  My cd/dvd drive does not read any discs be it, white, written or commercially written. It opens and closes and is light to show that he is working on. Device Manager indicates that the device is functioning properly.

  Tried the update of drivers, no update available. Tried restoring the system back 1 day and 1 week and 1 month, then and still the problem cannot be corrected. When I put a cd/dvd in the drive and try to access it, it says: D:\ is not accessible. The request could not be performed because of an i/o device error.

  Can someone help me I tried everything my friends and I can think, or is it better to send just to toshiba warranty.

  If the solution proposed by James will not help, you should try to remove the drive to CD/DVD in Device Manager.
  After phone restart the operating system will recognize and initialize the disk again.
  After this review of the procedure if you can read, write the middle.

• Second hard drive is not detected

  Hi, I bought an ssd to replace the hard drive of my acer e5 571g 50ns.
  Using a desktop computer, I transfer the os and oem SSD partiton.
  Because the laptop have a fake cd/dvd player I bought an adapter 2.5 ".
  So, I put the ssd sata port where before there was the hard drive and put the hard drive into the adapter port sata cd/dvd.
  When turning on pc the ssd is detected and it works perfectly, but the old hard drive is not detected. He is not shown in Device Manager

  As the garancy struck down, using my campus license, I installed windows 10 removal of the oem partitions.

  Now my acer works perfectly with ssd and hdd.