Changes to the PowerConnect switch model?

The site lists currently is no longer the series 5500, 6200, 7000 or 8100 PowerConnect switches in the Affairs of small/medium section of networking. Looking for a watch 5548 no product. Everything that is listed is the 2800, 3500 and Force10 product lines.

Is this just a mistake of the site or are these templates being deleted/replaced?

It is a mistake, these models are not gradually. They are visiting the area of big business to www.dell.com.

> Go to www.dell.com.

> click "for large companies.

> click on "servers, storage, network.

> click on 'Networking '.

You have reason, allowing these to be included in the area of medium-sized enterprises, and they will probably have to be.

Tags: Dell Switches

Similar Questions

List of SNMP OID of the PowerConnect switches

Hello

I was wondering if anyone could can give advice on this survey, like all my research and investigations have not until this product no result.

I conclude on a significant deployment for a customer who has a mixture of 80xx PowerConnect 62xx, 55xx and M8024K blade, M6348 switches. All switches are deployed and operational, and we are now trying to set the SCOM server to use SNMP to retrieve events etc. of the switches.

the problem is that I couldn't find SNMP OID anywhere to concerned, switches that are required. the events that we want to keep an eye on relate to connect the downs, lag switch, battery, authentication and critical failures for the models.

There is no requirement for the consumption of its use, of temperature, fan or CPU power or memory, so they are not needed.

Are there SCOM management packs that might help out here?

Any advice or pointers will be greatly appreciated.

Cheers.

Richter,

Looks like you just need to install traps to send alerts to your SCOM server. Normally, to see the things that you listed as changes to links, lag, batteries, authentication failures and other critical changes of your switches, it is not necessary ask an OID. All the these can be controlled automatically traps. The processor, memory, temp, fan and power you listed are in a different category, because they are all sensors in the switch that can send a trap when a threshold is reached, but can also be queried for exact measurements. Traps are easier to use than to the vote an OID and let you keep an eye on the areas that you mentioned. To install traps, set your community on your switches string and the management server, enable all traps and configure your management as your recipient of the host server. The commands are:

(config) #snmp - known private community server

(config) #snmp - server enable traps all

(config) #snmp - private host 10.10.10.5 Server

I hope it's useful for you.

B

Transfer the PowerConnect switch settings to N3000

Hello

I am trying to copy paste the settings currently, we run in a for a new N3048 PowerConnect 6448.

Unfortunately, it seems that many commands use the same syntax they used to have. CLI reference guide did not help much, because it is not compare or tell me what commands are the same for PowerConnect to N3000.

The I am trying to copy the parameters are as follows (in bold lines that receive questions):

! Current configuration:

! Description of the system "Powerconnect 6248, 3.2.0.7, VxWorks 6.5.

! Version of the software system 3.2.0.7

! Passage mode is configured as disabled

!

Configure

GVRP enable

database of VLAN

VLAN 2, 8-10, 15, 100

VLAN 2 1 routing

VLAN 8 2 routing

VLAN routing 9-3

VLAN 10 4 routing

VLAN routing 100 5

output

hostname "awsspcsw01".

battery

1 2 Member

output

address 192.168.20.1 255.255.255.0

IP - awstruewind.local domain name

IP routing

IP route 0.0.0.0 0.0.0.0 192.168.1.100

IP route 172.21.0.0 255.255.0.0 192.168.1.100

IP route 172.20.0.0 255.255.0.0 192.168.1.100

IP route 192.168.255.0 255.255.255.0 192.168.1.100

IP route 192.168.2.0 255.255.255.0 192.168.1.100

192.168.1.1 IP helper-address

interface vlan 2

name "Server VLAN.

Routing

IP 172.23.1.1 255.255.255.0

output

interface vlan 8

name "IL VLAN.

Routing

IP 172.23.8.1 255.255.255.0

output

interface vlan 9

name "VLAN voice."

Routing

IP 172.23.9.1 255.255.255.0

output

interface vlan 10

name "VLAN user.

Routing

IP 172.23.10.1 255.255.255.0

IP helper 172.23.1.25

output

interface vlan 100

name 'Legacy VLAN.

Routing

IP 192.168.1.254 255.255.255.0

output

spanning tree priority 8192

!

I haventerface ethernet 1/g1

switchport access vlan 100

output

!

I haventerface ethernet 1/g2

switchport access vlan 2

output

!

interface ethernet 1/g3

switchport access vlan 100

output

!

interface ethernet 1/g4

switchport access vlan 10

output

!

interface ethernet 1/g5

switchport access vlan 10

output

!

interface ethernet 1/g6

switchport access vlan 10

output

!

interface ethernet 1/g7

switchport access vlan 10

output

!

interface ethernet 1/g8

switchport access vlan 10

output

!

interface ethernet 1/g9

switchport access vlan 10

output

!

interface ethernet 1/g10

switchport access vlan 10

output

!

interface ethernet 1/g11

switchport access vlan 10

output

!

interface ethernet 1/g12

switchport access vlan 10

output

!

interface ethernet 1/g13

switchport access vlan 10

output

!

interface ethernet 1/g14

switchport access vlan 10

output

!

interface ethernet 1/g15

switchport access vlan 10

output

!

interface ethernet 1/g16

switchport access vlan 10

output

!

interface ethernet 1/g17

switchport access vlan 10

output

!

interface ethernet 1/g18

switchport access vlan 10

output

!

interface ethernet 1/g19

switchport access vlan 10

output

!

interface ethernet 1/g20

switchport access vlan 10

output

!

interface ethernet 1/g21

switchport access vlan 10

output

!

interface ethernet 1/g22

switchport access vlan 10

output

!

interface ethernet 1/g23

switchport access vlan 10

output

!

interface ethernet 1/g24

switchport access vlan 10

output

!

interface ethernet 1/g25

switchport access vlan 2

output

!

interface ethernet 1/g26

switchport access vlan 10

output

!

interface ethernet 1/g27

switchport access vlan 10

output

!

interface ethernet 1/g28

switchport access vlan 10

output

!

interface ethernet 1/g29

switchport access vlan 100

output

!

interface ethernet 1/g30

switchport access vlan 100

output

!

interface ethernet 1/g31

switchport access vlan 10

output

!

interface ethernet 1/g32

switchport access vlan 10

output

!

interface ethernet 1/g33

switchport access vlan 10

output

!

interface ethernet 1/g34

switchport access vlan 10

output

!

interface ethernet 1/g35

switchport access vlan 100

output

!

interface ethernet 1/g36

switchport access vlan 10

output

!

interface ethernet 1/g37

switchport access vlan 10

output

!

interface ethernet 1/g38

switchport access vlan 100

output

!

interface ethernet 1/g39

switchport access vlan 10

output

!

interface ethernet 1/g40

switchport access vlan 10

output

!

interface ethernet 1/g41

switchport access vlan 10

output

!

interface ethernet 1/g42

switchport access vlan 10

output

!

interface ethernet 1/g43

switchport access vlan 10

output

!

interface ethernet 1/g44

switchport access vlan 10

output

!

interface ethernet 1/g45

switchport access vlan 10

output

!

interface ethernet 1/g46

switchport access vlan 100

output

!

interface ethernet 1/g47

switchport access vlan 100

output

!

interface ethernet 1/g48

Description "trunk at awsbodsw01.

GVRP enable

switchport mode trunk

switchport trunk allowed vlan add 2,8,100

output

Server SNMP community awstruewind ro

output

Database VLAN, this command is just #vlan.

Console (config) #vlan 2,8,9,10,100

To enable overall VLAN routing using the following command.

Console (config) #ip Routing

The IP address is a command based interface.

Console (config) #interface vlan 1

Console (config-if-vlan15) #ip address 92.168.20.1 255.255.255.0

The command name has not changed, just make sure that you are in the interface VLAN.

Console (config) #vlan 2

Console (config-vlan2) #name "Server VLAN.

To enter a physical interface use the following command.

Console (config) # interface gigabitethernet 0/1/2

I hope this helps.

Without change to the FC switch to mode mode end-host FC

In the window of maintenance last night, I was going to spend one of my systems UCS switch FC FC end-host Mode. The intention was to be able to reach the storage systems via an external FC SAN, instead of the current situation where storage is directly attached to the FIs. The UCS system in question is redundant fabric 6248UP of interconnections, blades are all of the B200M2 or the B200M3, and infrastructure (UCSM, FIs and IOM) running version 2.2(3a).

The plan was relatively simple. First of all, I would like to change FI B mode end-host FC. Once this has been done re - I would record vHBAs the blades attached to the fabric B in my storage system, so that they could access their storage via the external SAN. Then I go through all the blade servers and ensure that they had access to storage multipath healthy and tolerant, how I would like to repeat the process for FI.

It turned out to be a disaster, however. Once I started the process of change FI B FC end-Host mode, FIs times restarted, and all servers access storage and network. When they came again, both of them had changed the fashionable end-host FC, which means that none of the blades had access to their storage volumes more. So there is nothing to do but to return the change. Yet once, two FIs restarted at the same time and they both returned to the top in switching mode of CF. A few hours later, after have rebooted most of blade servers and cleaning applications having failed, we were in normal production.

So what I was asking here why on Earth the two of my FIs restarted at the same time. Is this a known bug? The user interface would certainly think one can ignore at a time as I had planned, because the CF implemented end-Host Mode action link is on the page of each individual FI in UCSM (under hardware-> connections-> interconnection fabric A fabric / B). (So the action Set FC Switching Mode of link, incidentally.) Also, when I click on this link, I get a warning saying local ' are you sure you want to set the mode of end-host FC? If you select Yes , the fabric of interconnection will restart and this application will disconnect'. Note the use of the singular here; the warning refers to an single fabric of interconnection, which is perfectly logical that the change was requested only on one two FIs.

Torus

I quite understand your point!

The wording is misleading, because it is not in order with a completed receipt one.

That's why Kenny of the TAC wrote the answer above.

In my opinion, the documentation must be corrected.

PowerConnect switch and Cisco routers

I have 4 Cisco routers connected to our Dell Powerconnect 7024. This is a laboratory environment where I'm having every act of router (2 per site) as a WAN gateway for these 2 sites.

Site 1 Site 2

2 3 router

PC - Dumb_switch PowerConnect Dumb_switch client - PC Client

Router 1 router 4

There are a few other Vlans on the switch with connected devices. With the current configuration, these two sites can communicate with any other "site" connected to the switch on each route, with the exception of the other.

Directly connected to the router interfaces are in trunk mode, as it's the only way I could get the dell to connect with the Cisco. Ive read in other threads that the general mode is usually suggested on the powerconnect switch, but had no luck with this configuration.

Router 1---> item in gi1/0/15 (vlan 10)

Router 2---> item in gi1/0/14 (vlan 11)

Router 3---> item in gi1/0/22 (vlan 16)

Router 4---> article gi1/0/23 (vlan 14)

Example: a ping from Site 1 can reach int 22 of the switch without problem, but I can't ping jump according to R3. As all the other devices on this switch can talk to these sites, I'm not clear if the problem is my config switch dell or routers. Any input would be greatly appreciated. Thank you!

! Current configuration:
! Description of the system "PowerConnect 7024, 5.1.2.3, VxWorks 6.6"
! 5.1.2.3 system software version
! 'Normal' system operation mode
!
Configure
GVRP enable
VLAN 2-7, 9-14, 16
output
VLAN 2
name 'BOSTON '.
output
VLAN 3
name "MIAMI".
output
VLAN 4
name of 'THE
output
VLAN 5
name "SEATTLE".
output
VLAN 6
name "DALLAS".
output
VLAN 7
name "London".
output
VLAN 9
name "Frankfurt".
output
VLAN 10
name "Rome".
output
VLAN 11
name "Sczecin.
output
VLAN 12
name "Budapest".
output
VLAN 13
name "Moscow".
output
VLAN 14
name "Quebec".
output
-Other - or ITU (q)
VLAN 16
name "Winnipeg".
output
hostname "Devlin".
location 1/0 2. PowerConnect 7024
clock timezone-5 minutes 0
battery
1 2 Member! PCT7024
output
out-of-band interface
Shutdown
output
no ip domain-lookup
"local" IP domain name
IP routing
IP route 0.0.0.0 0.0.0.0 172.16.37.3
IP route 172.16.37.160 255.255.255.240 172.16.37.162
IP route 172.16.37.112 255.255.255.240 172.16.37.162
IP route 172.16.37.112 255.255.255.240 172.16.37.147
IP route 172.16.37.144 255.255.255.240 172.16.37.147
IP route 172.16.37.240 255.255.255.240 172.16.37.244
IP route 172.16.37.224 255.255.255.240 172.16.37.244
IP route 172.16.37.224 255.255.255.240 172.16.37.217
-Other - or ITU (q)
IP route 172.16.37.208 255.255.255.240 172.16.37.217
ARP 172.16.37.162 0022.9057.7F51
interface vlan 1
IP 172.16.37.4 255.255.255.240
bandwidth 10000
IP ospf cost 10
output
interface vlan 2
IP 172.16.37.17 255.255.255.240
output
interface vlan 3
IP 172.16.37.33 255.255.255.240
output
interface vlan 4
IP 172.16.37.49 255.255.255.240
output
interface vlan 5
IP 172.16.37.65 255.255.255.240
output
interface vlan 6
IP 172.16.37.81 255.255.255.240
output
interface vlan 7
-Other - or ITU (q)
IP 172.16.37.97 255.255.255.240
output
interface vlan 9
IP 172.16.37.129 255.255.255.240
bandwidth 10000
output
interface vlan 10
IP 172.16.37.145 255.255.255.240
bandwidth 1000
IRDP IP
output
interface vlan 11
IP 172.16.37.161 255.255.255.240
bandwidth 1000
IRDP IP
output
interface vlan 12
IP 172.16.37.177 255.255.255.240
bandwidth 100000
output
interface vlan 13
IP 172.16.37.193 255.255.255.240
bandwidth 1000
output
interface vlan 14
IP 172.16.37.209 255.255.255.240
bandwidth 1000
output
interface vlan 16
IP 172.16.37.241 255.255.255.240
bandwidth 1000
IP ospf cost 100
output
No flowcontrol
!
interface item in gi1/0/3
spanning tree portfast
output
!
interface item in gi1/0/4
spanning tree portfast
output
!
interface item in gi1/0/5
spanning tree portfast
switchport access vlan 2
output
!
interface item in gi1/0/6
spanning tree portfast
switchport access vlan 3
output
!
interface item in gi1/0/7
spanning tree portfast
switchport access vlan 4
output
!
interface item in gi1/0/8
spanning tree portfast
switchport access vlan 5
output
!
interface item in gi1/0/9
switchport access vlan 6
output
!
interface item in gi1/0/10
switchport access vlan 7
output
!
interface item in gi1/0/11
spanning tree portfast
switchport mode trunk
output
!
interface item in gi1/0/12
spanning tree portfast
switchport mode trunk
output
!
interface item in gi1/0/13
switchport access vlan 9
output
!
interface item in gi1/0/14
Speed 100
full duplex
switchport mode trunk
switchport general allowed vlan add 10 tag
switchport access vlan 10
output
!
interface item in gi1/0/15
Speed 100
full duplex
switchport mode trunk
switchport general allowed vlan add 11 tag
switchport access vlan 11
output
!
interface item in gi1/0/16
switchport access vlan 12
output
!
interface item in gi1/0/17
switchport access vlan 12
output
!
interface item in gi1/0/18
switchport access vlan 13
output
!
interface item in gi1/0/19
switchport access vlan 13
output
!
interface item in gi1/0/22
Speed 100
full duplex
switchport mode trunk
switchport general allowed vlan add 16 tag
switchport access vlan 16
output
!
interface item in gi1/0/23
Speed 100
full duplex
switchport mode trunk
VLAN allowed switchport General add 14
switchport access vlan 14
output
!
interface item in gi1/0/24

You could probably create a static route in Router 1 router 4 with a priority which is better than the other options, so we're going unless the link is down.

Transit VLAN on the PowerConnect 6224

I need help to sort out a problem with routing on a 6224 we have configured to act as a vlan transit for one of our branches. The general idea is 8.143 is the vlan of transit, of 8.144 is our PC LAN 8.145 will be our VOIP lan.

We have installed this switch with our WAN provided last week, but had to get out. Traffic seemed to happen to the WAN providers to our transit interface VLAN (172.22.143.254) wasn't going anywhere. It's symptoms

(1) we could ping from 172.22.144.x to 172.22.145.x and 172.22.143.x

(2) we could ping from 172.22.145.x to 172.22.143.x and 172.22.144.x

(3) we could ping from 172.22.143.x to 172.22.144.x and 172.22.145.x

(4) if I was plugged into the 6224 on with an address 143.x I could ping our remote control does site at 172.22.8.x no problem but not 144.x or 145.x

(5) 172.22.8.x, I couldn't ping 144.x or 145.x or 143.1 (I could ping 143.254 which is EXTENDED to suppliers to our switch network interface)

Here's the running to the switch configuration. Any suggestions would be greatly appreciated:

Console > activate

Console execution #show

! Current configuration:

! Description of the system "PowerConnect 6224, 3.3.6.4, VxWorks 6.5.

! 3.3.6.4 system software version

! Passage mode is configured as disabled

!

Configure

database of VLAN

VLAN 143-145

VLAN routing 143 1

VLAN routing 144 2

VLAN routing 145 3

subnet of VLAN association 172.22.143.0 255.255.255.0 143

subnet of VLAN association 172.22.144.0 255.255.255.0 144

subnet of VLAN association 172.22.145.0 255.255.255.0 145

output

battery

1 1 member

output

DHCP IP address

IP routing

IP route 0.0.0.0 0.0.0.0 172.22.143.254

interface vlan 143

Name the "Transit".

routing ip address 172.22.143.1 255.255.255.0

output

interface vlan 144

name "TWLAN".

routing ip address 172.22.144.1 255.255.255.0

output

interface vlan 145

the name "VOIP" routing

IP 172.22.145.1 255.255.255.0

output

level of 746f7a78621059d80fdc538acc40cbf2 user name 'admin' password encrypted 15

!

interface ethernet 1/g1

switchport mode general

VLAN allowed switchport General add 143

output

!

interface ethernet 1/g2

switchport mode general

VLAN allowed switchport General add 143

output

!

interface ethernet 1/g3

switchport mode general

VLAN allowed switchport General add 144

output

!

interface ethernet 1/g4

switchport mode general

VLAN allowed switchport General add 144

output

!

interface ethernet 1/g5

switchport mode general

VLAN allowed switchport General add 145

output

!

interface ethernet 1/g6 switchport mode General General switchport vlan allowed output adds 145! interface ethernet 1/g7 switchport mode General General switchport vlan allowed output adds 145! interface ethernet 1/8 switchport mode General General switchport vlan allowed output adds 145! interface ethernet 1/g9 switchport mode General General switchport vlan allowed output adds 145! interface ethernet 1/g10

switchport mode General General switchport vlan allowed output adds 145! interface ethernet 1/g11 switchport mode General General switchport vlan allowed output adds 145! interface ethernet 1/g12 switchport mode General General switchport vlan allowed output adds 145! interface ethernet 1/g13 switchport mode General General switchport vlan allowed output adds 145! General mode of interface ethernet 1/g14 switchport

switchport general allowed vlan add exit 145! interface ethernet 1/g15 switchport mode General General switchport vlan allowed output adds 145! interface ethernet 1/g16 switchport mode General General switchport vlan allowed output adds 145! interface ethernet 1/g17 switchport mode General General switchport vlan allowed output adds 145! interface ethernet 1/g18 switchport mode General switchport General allowed vlan add 145

output! interface ethernet 1/g19 switchport mode General General switchport vlan allowed output adds 145! interface ethernet 1/g20 switchport mode General General switchport vlan allowed output adds 145! interface ethernet 1/g21 switchport mode General General switchport vlan allowed output adds 145! interface ethernet 1/g22 switchport mode General switchport General allowed vlan add exit 145

! interface ethernet 1/g23 switchport mode General General switchport vlan allowed output adds 145! interface ethernet 1/g24 switchport mode General switchport General allowed vlan add to exit 145

Console #.

It seems that port 1 must be in the VLAN 143, not general mode access mode. You already have a static route in place on the PowerConnect switch which directs traffic to the next break in the network. But it may be necessary for a place on the Cisco that allows to direct traffic to the PowerConnect switch.

Here is a good post to look through also.

http://en.community.Dell.com/support-forums/network-switches/f/866/t/19506015.aspx

Create a model that can be replicated, but will not show changes in the original model, which occurs in any comps duplicated from it?

I imported a doc I - 4 layers. Then I dragged these 4 layers in a new comp - comp1. I would like to reproduce this model so that I can try different things using these same 4 layers. But when I duplicate the comp I did - comp 2 - any change I make appear in comp1. How can I create a model that can be duplicated - but will not show changes in the original model, which occurs in any comps duplicated from it? Thank you very much!
(CS5.5)

It is a common misunderstanding when you start working in Ae. It takes time to get used to, and even veterans are still this error from time to time. Here's the thing, you have to get in your head: your project Panel is where your source material is, and the timeline is the place where there is a representation of this source. This means that if you duplicate an item in your timeline (particularly relevant for the precomps) it will duplicate a copy, not the source. so, if change you it - it will change all instances of this copy. If you want to duplicate a precomp and create another source, you will need to do it in a 4 step operation:
1. duplicate your precomp in the timeline (you got that day)
2. Select the source of this copy in the project Panel (currently the same precomp)-right click on the-> precomp 'reveal the source layer project.
3. duplicate the precomp selected in the project Panel
4. replace the copy in your panel mounting with the duplicate of the Source Panel (shortcut - Ctrl + alt + / when both are selected, or drag it to double with pressing Alt)
what you are really duplicate the precomp twice - once in the project window and once in the timeline, and then one link to the other.

HPCM error - definition model has changed since the last calculation
Hello world

I have a bit of a problem on an application Coordinator.

(1) message warning when I go to balancing-> "model has changed since the last calculation."
(2) message when I select cube considered in balancing-> 'the database has not been updated with the latest results of calculation."

What has been done before I got to this point:

(1) add a few lev 0 members in the current hierarchy for cost center
(2) run a comparison to check if they are picked up (OK!)
3) deploy EPMA (result: SUCCESSFUL message)
4) go to HPCM and deploy the two cubes (OK-> at least is what the status of the job)
(5) control of new members in OTL (OK! they are there)
(6) the HPCM Calc launch, check the box to erase all data of calc prev, check the box to regenerate calcs, check the box to transfer data to the reporting cube.
result: employment status: OK!

But in reality: never got transferred through to the reporting cube.

I repeated steps 1 through 6, a few times, I even changed something in the (alias) shared library to check if it went through.
In EPMA it says that the app is 'in sync with the deployment. And when I run a comparison with deployed application, it does not pick up anything.

Any ideas?

Thank you

Kind regards
Annie
Hello world

Just realised I never came back with the answer to my question. I was developing the new application and starts the compilation of the Calc sequentially, so while I was developing Calc for step 2 or 3, rebuild only those scripts are calculate only the specific areas. This is the reason why I received this message. As soon as I transferred both apps and recalculated at the beginning, the error message disappeared.
Just in case someone wondered.

See you soon,.
Annie

Changing the virtual switch name

Hello
Is it possible to change the name of the virtual switch, for example, when you create a new vSwitch in VI Center it starts with vSwitch1 can change you it to vSwitch2 providing their isn't another switch with this name?
Thank you

you change the esx.conf you need to reboot (be sure and create a backup of esx.conf... /etc/vmware/esx.conf_backup /etc/vmware/esx.conf cp)

If you found this information useful, please consider awarding points to 'Correct' or 'useful '. Thank you!

How to change the text dummy model editable region < head >

I created an editable in my template < head > so I can add a canonical link and redirect the link to each of the many pages that are based on the template. So I stupidly (I think) added some dummy text to add easier links recorded in each file, and uploaded them. Later, I realized that all my pages have this dummy text in it, what is wrong, of course.
So I deleted the dummy text in the template and saved, but nothing happened. All them are always this dummy text. So I can't get rid of it in my pages of distance. Why is it not my removal of the dummy text in the collage of the editable area?
Thank you!

Editing text or content areas can be changed to a model does not change in the pages of children who have already been created. Best suggestion would be to copy the dummy text, use find and replace to remove all the files (use search all Site Local), and then load the pages newly published on the server.

Gary

Changes to the model removes the document only css

<?php include("../application.php"); ?>
<!DOCTYPE html PUBLIC "-//W3C//DTD XHTML 1.0 Transitional//EN" "http://www.w3.org/TR/xhtml1/DTD/xhtml1-transitional.dtd">
<html xmlns="http://www.w3.org/1999/xhtml">
<head>
<link href="../css/styles.css" rel="stylesheet" type="text/css" />
<meta http-equiv="Content-Type" content="text/html; charset=UTF-8" />
<!-- TemplateBeginEditable name="doctitle" -->
<title>blank</title>
<!-- TemplateEndEditable -->
<!-- TemplateBeginEditable name="head" --><!-- TemplateEndEditable -->
</head>


<style type="text/css">
<!--
a:link {
     color: #B7242C;
     text-decoration: none;
}
a:visited {
     text-decoration: none;
     color: #B7242C;
}
a:hover {
     text-decoration: none;
}
a:active {
     text-decoration: none;
}
-->
</style>
<body>
<div id="wrapper">
  <div id="cartfb">
    <div id="facebook"><img src="../images/Logos/FBLogo.png" alt="Facebook" vspace="3" /><img src="../images/Logos/twitter_logo_sm.jpg" alt="Twitter" hspace="2" vspace="2" />    </div>
    <div id="viewcart"><?php echo($cartweaver->cw3CartLinks());?></div> 
  </div>
  <div id="navotis">
    <div id="otisbw"><img src="../images/Photos/otisbw.jpg" alt="Otis" /></div>
    <div id="navbar"><img src="../images/Navigation/Nav_Bar_Rev.jpg" alt="Navigation Bar" /></div>    
   </div>
  <div id="body">
    <div id="logo"><img src="../images/Navigation/Top_Left_Logo_New.gif" alt="Doggie Deli Logo" /></div>
    <div id="content">
      <div id="leftcolumn"><img src="../images/Navigation/CategoryBar.jpg" alt="Category Bar" width="85" height="342" /></div>
      <!-- TemplateBeginEditable name="EditRegion2" -->
      <div id="centercolumn">Lorem ipsum dolor sit amet, onsectetuer adipiscing elit, sed diam nonummy nibh euismod tincidunt ut laoreet dolore magna aliquam erat volutpat. Ut wisi enim ad minim veniam, quis nostrud exerci tation ullamcorper suscipi lobortis nisl ut aliquip ex ea commodo consequat. Duis autem vel eum iriure dolor in hendrerit in vulputate velit esse molestie consequat, vel illum dolore eu feugiat nulla facilisis at vero eros et accumsan et iusto odio dignissim qui blandit praesent luptatum zzril delenit augue duis dolore te feugait nulla facilisi. Nam liber tempor cum soluta nobis eleifend option congue nihil imperdiet doming id quod mazim placerat facer possim assum. Typi non habent claritatem insitam; est usus legentis in iis qui facit eorum claritatem. Investigationes demonstraverunt lectores legere me lius quod ii legunt saepius. Claritas est etiam processus dynamicus, qui sequitur mutationem consuetudium lectorum. Mirum est notare quam littera gothica, quam nunc putamus parum claram, anteposuerit litterarum formas humanitatis per seacula quarta decima et quinta decima. Eodem modo typi, qui nunc nobis videntur parum clari, fiant sollemnes in futurum.Lorem ipsum dolor sit amet, consectetur adipiscing elit, sed diam nonummy nibh euismod tincidunt ut laoreet dolore magna aliquam erat volutpat. Ut wisi enim ad minim veniam, quis nostrud exerci tation ullamcorper suscipit lobortis nisl ut aliquip ex ea commodo consequat. Duis autem vel eum iriure dolor in hendrerit in vulputate velit esse molestie consequat, vel illum dolore eu feugiat nulla facilisis at vero eros et accumsan et iusto odio dignissim qui blandit praesent luptatum zzril delenit augue duis dolore te feugait nulla facilisi. Nam liber tempor cum soluta nobis eleifend option congue nihil imperdiet doming id quod mazim placerat facer possim assum. Typi non habent claritatem insitam; est usus legentis in iis qui facit eorum claritatem. Investigationes demonstraverunt lectores legere me lius quod ii legunt saepius. Claritas est etiam processus dynamicus, qui sequitur mutationem consuetudium lectorum. Mirum est notare quam littera gothica, quam nunc putamus parum claram, anteposuerit litterarum formas humanitatis per seacula quarta deima et quinta decima. Eodem modo typi, qui nunc nobis videntur parum clari, fiant sollemnes in futrum.</div>
      <!-- TemplateEndEditable -->
      <div id="rightcolumn"></div>
      <div id="footer">Doggie Deli Boutique<br />
        2051 Cypress Creek Road Suite G  Cedar Park, TX 78613<br />
        Phone: (512) 249-8300  Email: <a href="mailto:[email protected]">[email protected]</a> </div>
    </div>
  </div>
</div>

</body>
</html>

Hello

I created a template in dreamweaver with an external style sheet. Then, I created a page for this model (called index) and to add div and css tags in the edit box that I set. I inserted a div tag and made a new rule for this div and saved in the current document, not the external style sheet. I thought this would be the right way, so I don't have an external stylesheet with a bunch of rules that does not apply to a bunch of pages. Now when I make a change to the model and save it, the css rule which I have added to the document only is removed. How can I fix this, or record all the rules on the external style sheet the right way to do it. Hope this makes sense, I'm not a very good storyteller. Incidentally a complete noob. I'll try and paste my code for the template. Thanks a lot for your help.

When you use templates, specific to the page CSS must be placed in the editable area of the head, as in:

Changes in the size of a footer in a model

As a project in my design course Web pages, I have designed a multy page web site with a dynamic area of 11 pages.
All 11 pages are built of a single model of the index page.
On a single page where there are 3 tab panels in each tab is open the footer of the part cannot be changed in the model
is 33% larger than on other 21 pages throughout the site. Anyone know why this is and is it fixable?
Which has shocked

http://forums.Adobe.com/thread/691654?TSTART=0

Why my pages evolve? Made changes to the model applied then.

I do a redesign of my site. I have made changes to my basic Page model but the tempeature each page differently. I changed the pages of tables of width % absolute. Even if I applied my changes to all pages that use the template, the change is not uniform throughout the site. I checked every page individually and each of them had different widths and % against pixels. I changed all of them manually. I went through the code and I just can't come up with a solution. They are not yet all online upward when you navigate from one page to another.
Can someone help me understand this? my site is deborahdavisdesign.com
I am working on Mac G5 OS 10.5.7 with a 2.5 GB of hd and 1.5 GB of ram. Using DW8.
Thank you very much.

My guess is that the majority of your site is in an editable area, they do not update. I think that you need to establish a new model or manually edit each page.

Gary

WS FTP and changes to the push model
He did years I used DW... We must use WS FTP Pro to the FTP files, or copy files directly from the server (but no FTPing in DW). That will affect our ability to make changes to the model out for any pages that use the template?

Thanks in advance,
Kristina

"HelpWriter" wrote in message
News:eme74s$50L$1@forums. Macromedia.com...
> It has been years I used DW... We must use WS FTP Pro FTP files,
> or
> copy files directly from the server (but no FTPing in DW). Who will be
> affect
> model our ability to push change on any page using the
> model?

N ° everything that DW made with models that happens on your local computer.
You can use any FTP software to transfer files. As long as you continue to
DW used to maintain pages, it is not serious allowing you to download them.

--
Patty Ayers | www.WebDevBiz.com
Free articles on the business of Web development
Web Design contract, quote request form, estimate Worksheet
--

Dell PowerConnect switches are prone to vulnerability of GNU Bash ShellShock?

Hello

I would like to know if the Dell PowerConnect switches are prone to vulnerability of GNU Bash ShellShock.

CVE-2014-6271

Best regards

Marie Therese TR

She will be registered there by the model number.

PC8024/PC8024F, PC7000, PC8100, PC6200 series.

Changes to the PowerConnect switch model?

Similar Questions

Maybe you are looking for