Cisco Telepresence 5320 MCU

Similar Questions

• Configuration of the firewall Cisco Telepresence MCU 5320

  Hi all.

  I searched all the documents of the MCU again, but I found nothing on the ports it uses.

  Help me

  HI Sandra.  The 5320 MCU is the same as 4500 MCU.

  Incoming ports

  • FTP - TCP:21 + transient (dynamic rather than fixed) used TCP ports for passive mode
  • HTTP - TCP:80
  • HTTPS - TCP:443
  • H.323 - TCP:1720 + ephemeral TCP ports for incoming calls
  • SNMP - UDP:161
  • Outgoing calls to H.323 involve ephemeral ports TCP connections TCP TCP:1720 and a certain number of ephemeral TCP ports
  • Outgoing SIP TCP calls involve connections between the TCP ephemeral ports and TCP:5060
  • Outgoing SIP TCP calls involve connections between the TCP ephemeral ports and TCP:5061
  • Outgoing interruptions SNMP are sent the ephemeral ports UDP Port 162
  • Media (including audio and video, FECC messages) are ephemeral ports from ephemeral ports UDP.
  • The products acquired Cisco TANDBERG/Codian and gateway series series Cisco TelePresence allocate the ephemeral ports between 49152 to 65535 *. It is possible to change the ports on which these products receive and establish connections. For example, by default the Codian products Cisco acquired listen port 1720 H.323 calls and connections to port 80 web browser, but these can be modified (go to network > Services).

  Keep in mind this MCU does not support the streaming or conference me and have either the GK aboard.  If these ports are listed.

  The link to the Article can be found here:

  http://www.Cisco.com/en/us/docs/Telepresence/infrastructure/articles/conferencing_products_conferenceme_ports_used_kb_3.shtml

  VR

  Patrick

• Cisco 5320 MCU layout / view

  We recently converted a MPS200 bridge to a microcontroller of 5320 Cisco.  We have multipoint Conference with 8 participants.  The new 5320 MCU automatically selected a layout component 9.

  It is that some of the participants in this appeal cannot see their auto show, as well as other 8 participants. They can switch back and comes between discovers them, and the participant discovers, but can't see both at the same time.

  This issue was addressed after his conversion to the new MCU.  Any advice?

  If you don't want to see for yourself, you will need to check the box.

  Do you see yourself with small squares
  Do not duplicate with small squares

  Please see the documentation for more information

  (taken from the online help you directly on the box (see the info / help buttons at the top of your mcu settings page))

  Do you see yourself with small squares	Prevents the MCU Conference participants their own videos into small tiles of views of the component of variable size (and conferences with the shutters of equal size).	If this option is set, then a participant will never appear in a small window (see auto), even if there is a free small component available.   They can still appear in larger shutters, however, for example, if the development of view is changed manually to show their video.  See understand how to show participants in the page layout view for more details.
  Do not duplicate with small squares	The MCU prevents duplicating large participating pane with small squares.	When you use a view of the Conference with some aspects of some small and large, the MCU will duplicate usually in a small window the video of a participant showed a large glass.  This is done to minimize the commutation of small tiles in response to changes in activity participating in the General pane.  If you prefer not to duplicate the participants into small tiles in this way, select this option.  For more details on view page layouts, see understand how to display the participants for the layout.

  In addition, it is not really clear what they see and how it is different and how they are passed to the page layout

  and how it behaves different for different endpoints.

  Is there a model, such as specific endpoint types, versions of the software, users...

  So maybe you could do some photos or even a short video.

  In addition to all this, I these two checkboxes and telling people to use their local view on their

  point endpoint to see if they need to check if they seem to always good :-)

  Most of the people I spoke to find annoying if they you themselves, especially as the MCU always adds some lag.

• a way to move c90 to 5320 mcu Conference

  I have a setup where we use the multi-site c90 option. Is it possible to move a video conference live from c90 to 5320 mcu. The reason is that there may be a 5 attending the video conference and c90 can handle 4 (3 + himself). I don't know if one needs for 5 participants before the video conference begins and I have no port on the 5320 MCU to run all the video conference with this

  Does anyone know a solution to this?

  Best regards

  Jesper

  Check:

  http://www.Cisco.com/en/us/docs/Telepresence/endpoint/codec-c-series/TC6/api_reference_guide/codec-C90-API-reference-guide-tc62.PDF

  
  xCommand Call UnattendedTransfer
  Transfers an ongoing call to another participant. The CallID is returned when the xCommand Dial command is run. During the call you can run the xStatus Call command to see the CallId. Fully supported for SIP calls only.
  Requires user role: USER
  Parameters:
  CallId(r): <0..65534> Number(r):
  Example:
  xCommand Call UnattendedTransfer CallId: 2 Number: [email protected]/* */ com
  *r TransferUriResult (status=OK): ** end
  

• 5320 MCU software update 3.1 TS

  We currently have 5320 MCU running version 4.5 (1.45). I see that Cisco offers code TelePresence MCU server:

  http://www.Cisco.com/c/en/us/support/conferencing/Telepresence-MCU-5320/model.html#releasenotes ~ rdtab1

  Looking at the release notes is not very clear if when running 3.1 GST in MCU we will lose the ability to "Téléprésence MCU" in CUCM to use this 5320 MCU for Ad - hoc conferences.

  I know that GST 3.1 does not offer this possibility, but if you look at the file name for the MCU is cisco_ts_3.1_1.98_for_mcu_5300.zip (32,04 MB) vs GST 3.1 cisco_ts8700_3.1_1.98.zip (26,24 MB)

  Thank you

  If you upgrade your 5320 MCU with the telepresence server migration software, it will transform the MCU in a server of telepresence for all functions and features will be a telepresence server and not a MCU.  See the Software of TS running on MCU 5300 Series installation guide on how to convert your MCU to a telepresence server, if you are interested.

  Here are two good discussions comparing platforms MCU and telepresence server, one of them specifically on migration from one to the other.

  What-difference-between-MCU-Cisco-Telepresence-Server

  Why-Replace-MSE-8510-MCU-44-Telepresence-Server-31

  The cisco_ts_3.1_1.98_for_mcu_5300 software is for a series of 5300 MCU migrating to a server of telepresence.  The cisco_ts8700_3.1_1.98 software is specifically for the hardware already running a TP server software, such as the various servers of telepresence models listed here, this includes MCUs migrated to the server TP as the 5300 MCU to MCU MSE 8510 series software.

• Driver of Cisco Telepresence - room LoopBack

  Hello world

  Is it possible to create a meeting room on Cisco Telepresence driver that will return the video to the appellant alone in the room? As the [email protected] / * / Cisco's Sip URI? (A kind of selfview room)

  Thanks for your help.

  It is possible to show only one participant connected to a MCU conference selfview, but not for telepresence Server conferences.  It comes without caring if the driver is involved or not.  The service provided by Cisco closure is obtained with the C40/60 endpoints where the audio and the video plays in a loop directly to the connected call (output HDMI to HDMI-in, output audio RCA audio-in RCA/RCA).

• 5320 MCU Sip settings

  I want to deploy 5320 MCU as multimedia cm unified using this resource guide (page 36). But I did not 'Use the trunk' option on page settings_sip.html webUI. I also have access to an another 5320 MCU with the same set of function keys, where this option is available. Only difference between the two devices is the firmware version:

  4.4 (3.42) on my device and 4.5 (1.45) on devices where "Trunk of use" is available.

  Q1: Should I upgrade or there is workaround to use sip trunk without this option?

  Q2: Do I have to pay for this update?

  Q3: If my distributor can not get it to me or my relationships with them stopped can get updates directly from cisco?

  See the section "Deployment of a Unified CM MCU as a multimedia resource" in the installation guide that matches your version of software MCU.

  MCU 4.4 Installation Guide

  MCU 4.5 installation guide

  Upgrades of software MCU does not require a key to unblocking, but a contract of active service for the MCU is required to download the software.

  Series 5300 MCU software

• Cisco VCS and MCU - Conference does not

  Dear community members

  I have problems in the VCS configuration to work with the MCU to join to several endpoints in a conference. The components that I use:

  -Cisco VCS control v8.7.

  -Cisco 5300 MCU 5310 v 4.5 (1.72)

  -3 x SX20 end points

  I recorded every endpoint and MCU on VCS, but I'm not able to do a conference call 3-way, the only option is 1 video and 1 audio (I disabled the Multisite option). It seems that VCS does not yet call the MCU in the game.

  Kindly help us with it.

  Can you tell us how you set up the Conference and how you have configured MCU and endpoints?

  From the sounds of it, you call each end point of one of the SX20s, but you must call simply directly in the Conference on the MCU.  If you want to have a conference point to point between two end points and then degenerate into a multipoint conference on the MCU, you must configure Multiway.

  With the help of Multiway with Cisco TelePresence systems

• Extension of Cisco TelePresence Management Suite Analytics

  Hello - I have a few queries on Cisco TelePresence Management Suite Analytics Extension and wanted to get help on the same.

  A. Cisco active development on this product and/or have predefined routes for this platform? We have not quite

  hear updates during the liberation of UC SEVT 10.0 for this platform?

  B. what kind of support is available for this platform in a perspective of customization of the report?

  C. are there examples of SQL scripts that could be re-used to produce reports of the below type:

  • Video endpoint / use of rooms
  • Number of subscriptions too video session
  • Capacity Trending & forecasting for the use of a Port of MCU and increases endpoint.

  D. What are the technical limitations known from the point of view analytics platform? In other words, it does not imply that

  the analytical potential lies in the hands of developer and NOT the platform, taking into account its APIs?

  Thank you

  SG

  See this thread, message of Kjetil Rees (marked as a correct answer) in particular:

  https://supportforums.Cisco.com/message/3449977

  You aren't going to get an answer about the development plans and roadmaps here in a public forum, you will need to contact your Cisco representative for this kind of information.

  If you want something where all the work has been done for you, and that is customized to your specific needs, then you might want to consider looking at vAnalytics, http://vyopta.com/products/vanalytics of Vyopta, http://vyopta.com/

  No, I am not associated with Vyopta, however, we use one of their products.

  /Jens

  Please note the answers and score the questions as "answered" as appropriate.

• 5320 MCU in TMS - booking Conference

  I have a new 5320 MCU configured and managed in the TMS.  I can create a conference directly on the MCU, add participants, and it will dial a number and join the participants to the call correctly.  However, if I try to book a conference at TMS by selecting the participants and resource MCU, MCU does not connect endpoints for the call.  If I look at the details of calls that it said shows the following.  It's like he is waiting for the client to call the bridge, not the MCU outbound calls to customers?

  Participants will connect using this route:

  Customer MOVI ==> Bridge

  Hi if it is customer movi you attempt to dial, you must assign the automatic Conference connect and then add outgoing call participants where you type the movi/jabber address manually. You can see the connection setting tab before saving the Conference to see how the call will be set up (if the mcu expectd the customer allowing to switch or the mcu dial out). Customer MOVI has not automatically as regular endpoints generally have for the SCM cannot guarantee the call will implement.

  /Magnus

  Sent by Cisco Support technique iPhone App

• Is any impact of a change of the password of the local user account on an instance of a content server Cisco TelePresence virtual computer?

  Hello

  I'm looking to see if there is an impact to change the password of the local user account on an instance of a content server Cisco TelePresence virtual machine?

  The software version is v6.2 build 4073.

  Thank you in advance,

  Robert

  I'll assume, you are referring to the administrator account, but it can be applied to any local account which is located on the TCS server itself.  It has no impact to change the password, unless you are using doesn't say account to connect to the server of TCS or web interface, it will not affect the application of TCS as most things such as external storage or clustering rely on domain accounts and not the local server.

• Cisco TelePresence Manager version 1.7 does support Windows Small Business Server 2008?

  Hello

  Is Microsoft Windows Small Business Server 2008 supported the Protocol LDAP, AD and MS Exchange server for Cisco TelePresence Manager version 1.7?

  Thank you

  AA

  Hello Ahmed - although this configuration "can work", Windows 2008 Small Business Server is not on the support list. This means that it has not been tested and it certifies to work with telepresence.

  To my knowledge, he's not on the roadmap for the future support however, I search and repost as soon as I have an answer for you.

  Kind regards

  -Andrew

  Sent by Cisco Support technique iPhone App

• Cisco TelePresence SX20 with laptop

  I use a Cisco TelePresence as autonomous SX20 endpoint configured with a public IP address (in Pakistan). I want to connect a portable computer (to Canada) to start video conferencing using the portable camera. Please advice me the software to install on the laptop so that I can start with my SX20 videoconferencing based on IP configured on my SX20.

  To understand kindly refer to the disposal of partner network.

  Please help me its urgent.

  Hello

  www.ciscojabbervideo.com

  BR Oleksandr

• Cisco telepresence sx20

  Dear support team,

  I want to know how to configure cisco telepresence sx20.

  any body can help pls...

  Configuration Cisco Telepresence Sx20 is not easy to do. I think below link will help you for configuration.

  http://www.Cisco.com/c/dam/en/us/TD/docs/Telepresence/endpoint/quick-set-SX20/TC5/administrator_guide/sx20_quickset_administrator_guide_tc51.PDF

• Cisco Telepresence SX20 and Touch 8 Configuration after paired

  Hello

  I successfully connected and combined the SX20 Cisco's Telepresence and Cisco Telepresence Touch 8. Before using the 8 key, we used the remote control instead. As a result, I have two questions about this.

  1. as far as I know, when I use the 8 key, the remote control cannot be used. Is it possible to use both of them?

  2. How can I change the background of my SX20 touch 8? Previously, the remote I can easily choose the background for my SX20. But after pairing with Touch 8, background in my SX20 become a blue large clock. I really want to have a different background but cannot find the way how to change.

  Any help would be appreciated.

  Thank you.

  Sincerely,

  Bagus Hanindhito

  After you connect the 8 Touch, you can still use the remote control, you will need to put on the SX20:

  SystemUnit MenuType experimental configuration: full

  I think that the standard background when using a touchscreen device is what you see, blue with large clock.  However, after the MenuType return in full which will give you the full OSD which is used with the remote and not that of the button, you may be able to change the background then.