Cisco Aironet AIR-SAP2602I-E-K9 WAP config autonomous and roaming

Similar Questions

• SG300-52 and cisco AIR-SAP2602I-E-K9 does not

  Hello

  I am faced with a slight problem after upgrading my 3Com layer 2 switches with SG300-52.

  Cisco Air 2602i worked very well when it is connected to the switch 3Com and users are assigned IP of server (Active Directory), but whenever we try to connect 2602i with SG300, users cannot access the same ping drops network

  The two routers and switch working on speeds Auto as well as duplex automatic

  What could be the problem

  Hi shrry8,

  Thank you for the update.  For the port connected to the access point if you connect to a PC or something else to this port things work as expected?

  Also how are feed the Cisco 2602i Air?  PoE or adapter?

  I would also check the roles of smart port for this interface.  The role should be to the access point that is showing a different role?  This can be checked under Smartport > settings of the Interface.

  Kind regards

  Michael D.

  If this post is helpful please note or mark it as correct.

• Cisco Aironet 2600 series Configuration of the DHCP server is NOT serving addresses?

  Cisco Aironet 2600 series Configuration of the DHCP server is NOT serving addresses?

  I have (2) AIR-SAP2602I-A-K9, configured the same way.

  on two different remote LANs.

  They don't seem to be handing out addresses via DHCP.

  {If I connect to a local network with another DHCP server}

  wireless devices can obtain addresses

  This another DHCP server on the LAN through the access point.}

  I followed 12.4.25d. JA.cg.pdf

  Configuration of the Access Point to provide the Service DHCP 5-22

  ---------|---------|---------|

  e.g. 3444-RCS1-AN #show running-config

  Building configuration...

  version 15.2

  3444-RCS1-YEAR host name

  no ip Routing

  USH - DM IP domain name

  DHCP excluded-address IP 192.168.29.89

  IP dhcp RCS1 pool

  network 192.168.29.88 255.255.255.248

  router by default - 192.168.28.1

  Rental 1 0

  interface BVI1

  IP 192.168.28.211 255.255.254.0

  no ip route cache

  default IP gateway - 192.168.28.1

  ---------|---------|---------|

  ---------|---------|---------|

  e.g. 3444-RCS2-AN #show running-config

  Building configuration...

  version 15.2

  3444-RCS2-YEAR host name

  no ip Routing

  USH - DM IP domain name

  DHCP excluded-address IP 192.168.129.81

  IP dhcp RCS2 pool

  network 192.168.129.80 255.255.255.248

  router by default - 192.168.128.1

  Rental 2 0

  interface BVI1

  IP 192.168.128.171 255.255.254.0

  no ip route cache

  default IP gateway - 192.168.128.1

  ---------|---------|---------|

  Thats the DHCP Pool range 192.168.29.88 through 192.168.28.95

  Well this will confuse your customers.

  And this is NOT how to set up your "range".   See below:

  DHCP excluded-address IP 192.168.29.1 192.168.29.87

  DHCP excluded-address IP 192.168.29.96 192.168.29.254

  IP dhcp RCS1 pool

  network 192.168.28.211 255.255.254.0

  router by default - 192.168.28.1

  Rental 1 0

• Cannot turn off the LEDS on Cisco Aironet 1141

  I am trying to turn off the LED on a Cisco Aironet 1141 p/n AIR-AP1141N-A-K9.  It is a standalone AP and the CLI I publish this command:

  turn off the display of #led AP (config)

  The light does not go out after you type this command.  If I "run" it appears in the config so that the order has been accepted.  Is there another way to turn off the LED?  I'm under JA1 IOS Version 12.4 (21a).

  If you have the AP 1141 under warranty, you can send an email to [email protected] / * / PA serial number and they can post you the picture ask you.

  You want to say "Thank you"?
  Ne. Just note the useful responses,
  It is more useful than 'thank you'.

• Cisco Aironet SAP1602E - changing open to WPA - PSK access remote (RAP and map)

  I currently have a deployment of Cisco Aironet SAP1602E Wireless point to point bridge (bridge using RAP and card, root wireless and Non-Root Bridge) to expand a layer 2 VLAN from one building to the other. It currently operates uisng open authentication and encryption - and is administered remotely via the bridge of root, to get wireless (manage) the bridge Non-Root - RAP wireless remote.

  Try to configure the PSK WPA2-PSK remotely via the GUI or CLI - first setup - I informed a similar error to her below indicating that:

  Error: Key-management WPA is requried for WPA-PSK

  Read around, it seems, there is a configuration-control problem, and that I need to specify the mode as WPA2-PSK first, before then being able to specify the PSK there instead of using. However, as soon as this mode is specified on RAP, my remote administration is broken - as probably the RAP try to use WPA2-PSK to look for a PSK, which has not yet been configured. Am I missing something obvious here, or is the order of operations of CLI (1] convert to WPA - PSK; (2] shared secret to apply PSK) as a migration from open to WPA2-PSK cannot be configured remotely (short of preparation of a startup-config; TFTPing presents more; and issuance of a 'reload' remote control)? Can someone please enlighten me as to what the logic is here - no doubt I should be able to specify a PSK first (fo without worrying if I use WPA, WPA2 or other), and then be able to specify that I want as the layer of encryption (WPA) to make use of this pre-parameter PSK? If it was a router, you don't can me to add something to the authentication key chain OSPF; before clarifying its use - why so different Aironet Wireless IOS?

  You're right, and because you will have to enter several lines of configuration to switch to WPA2-PSK with AES didn't really matter; the AP would reset the radio anyway because you make changes related to the radio interface. It would be very useful that if Cisco router/switch IOS 'macro' feature available AP thus in changes like this, unfortunately this is not the case.

  Start with the nonroot AP and make sure that the following lines are added to your configuration. If you add by the console, the order must be like that, do it by downloading a new configuration of booting with tftp, that it does not matter.

  interface Dot11Radio0
  encryption ciphers aes - ccm mode

  SSID dot11 TEST
  authentication wpa key management
  WPA - psk ascii 0

  Please rate helpful messages... :-)

• Cisco Aironet 1830 disable broadcasting of the SSID

  I recently bought a Cisco Aironet 1830 with the mobility Express version. installed 8.2.100.0. This unit is my controller and my only AP. I configured the device, but I can't seem to find a setting in the GUI or the CLI of the controller or AP disable broadcasting of the SSID. Can someone help with this?

  Thank you

  The CLI is available, the following command:

  config ssid broadcast disable wlan where wlan id is the number of your wlan. If in doubt, do a show wlan summary which should give you this info, I hope.

  Ric

• Stand-alone configuration of Cisco Aironet 700i

  Hello

  I'm well aware new products Cisco. So please forgive my basic questions.

  I have Cisco Aironet 700 series AP(AIR-SAP702I-Q-K9). I don't have a controller. I need to set this up as standalone access point.

  I tried all the basic steps and tried to activate the two radios, but no luck. Anyone can guide me please on how to configure the AP.

  I use web access to configure the AP.

  Help, please

  Thank you

  Sagar

  Hi Sam,

  Please check these messages to set up autonomous AP.

  https://rscciew.WordPress.com/2014/05/24/single-SSID-configuration-on-au...

  https://rscciew.WordPress.com/2014/05/24/multiple-SSID-configurations-on...

  Concerning

  Remember messages useful rates

• New Cisco Aironet 1602i is not broadcasting the SSID I place

  New Cisco Aironet 1602i is not broadcasting the SSID I place

  SSID I set up is not broadcasting, so I don't see the wireless network to choose and connect. On my laptop if I choose specify the name of the SSID then I am able to connect to the wireless network. I have only 1 Configuration SSID on the access point. Anyone know how to update the configuration for the SSID is broadcast?

  The green light on the AP flashes and turns off about 3 seconds; is this normal or should it stays on all the time?

  Current configuration: 1842 bytes

  !

  version 15.2

  no service button

  horodateurs service debug datetime msec

  Log service timestamps datetime msec

  encryption password service

  !

  host ap name

  !

  !

  Pulse 9 logging console

  enable secret 5 $1$ rrlE$ msWqu8CGY/tpDkgRAAAIe /.

  !

  No aaa new-model

  no ip Routing

  no ip cef

  !

  !

  !

  dot11 syslog

  !

  dot11 ssid Mi Casa

  open authentication

  authentication-key wpa version2 management

  WPA - psk ascii 7 142017070F0C787B7579

  !

  !

  Crypto pki token removal timeout default 0

  !

  !

  username Cisco privilege 15 password 7 112A1016141D

  !

  !

  Bridge IRB

  !

  !

  !

  interface Dot11Radio0

  no ip address

  no ip route cache

  !

  encryption algorithms aes - ccm tkip encryption mode

  !

  SSID Mi Casa

  !

  gain of antenna 0

  STBC

  beamform ofdm

  root of station-role

  Bridge-Group 1

  Bridge-group subscriber-loop-control 1

  Bridge-Group 1 covering-disabled people

  Bridge-Group 1 block-unknown-source

  No source of bridge-Group 1-learning

  unicast bridge-Group 1-floods

  !

  interface Dot11Radio1

  no ip address

  no ip route cache

  !

  encryption algorithms aes - ccm tkip encryption mode

  !

  SSID Mi Casa

  !

  gain of antenna 0

  DFS block 3 Strip

  STBC

  beamform ofdm

  channel SFR

  root of station-role

  Bridge-Group 1

  Bridge-group subscriber-loop-control 1

  Bridge-Group 1 covering-disabled people

  Bridge-Group 1 block-unknown-source

  No source of bridge-Group 1-learning

  unicast bridge-Group 1-floods

  !

  interface GigabitEthernet0

  no ip address

  no ip route cache

  automatic duplex

  automatic speed

  Bridge-Group 1

  Bridge-Group 1 covering-disabled people

  No source of bridge-Group 1-learning

  !

  interface BVI1

  IP 192.168.10.200 255.255.255.0

  no ip route cache

  !

  by default-gateway IP 192.168.10.1

  IP forward-Protocol ND

  IP http server

  no ip http secure server

  IP http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag

  !

  1 channel ip bridge

  !

  !

  !

  Line con 0

  line vty 0 4

  local connection

  transport of entry all

  !

  end

  Hi you must guest mode config on the ssid... Read this bud

  https://supportforums.Cisco.com/docs/doc-5442

  Sent by Cisco Support technique iPhone App

• Only the needs of the Cisco Aironet 1550 series a WLC?

  Hello

  Nice day.  I would like to ask if the Cisco Aironet 1550 series requires a controller to run.  Note that the references SKU in this fomat AIR-CAP1552E-A-K9-AIR-CAP1552EU-A-K9.  I noticed that on the autonomous access point there they keyword 'SAP' on its SKU while the controller based has "CAP".  If the

  Cisco Aironet 1550 Series needs a controller which controller should it be associated? (e.g. AIR-CT2500)

  Thank you

  It can work stand-alone image:

  http://www.Cisco.com/en/us/partner/docs/wireless/access_point/iOS/release/notes/15.2_2_JB.html#wp355908

  1550 relies on:

  2500, 7500, 5508, WISM2,... .etc

  check the release notes of the code controller that you have and you should be able to identify what is supported and what is not supported.

  ----------------------------------------------------------------------------------------------

  Please ensure good answers to rate

• Help with a Cisco Aironet 1242AG

  Alright. So, I want to start by saying that I have what I consider to be the basis of knowledge of network management. I recently got a Cisco Aironet 1242AG WAP. I realize that this is not a stand-alone router. I would use it as an extension of my current router. From now on, the status light is alternating colors. If I understand correctly, it can not find the controller. I cannot telnet inside, or use web browser interface. Both say that the connection is not available. However, when I check my DHCP from my router table, I see that an IP address has been assigned to the MAC for the WAP. I tried to do a factory reset holding MODE until I plug the power supply and wait until it turns amber. After a few minutes and go through a few changes led, it goes back to the alternating colors on an ongoing basis.

  I don't really know where to go from here. Help, please.

  Thank you

  Kris

  Radios allow without a ssid that are attached to them. You will need to create your ssid and then fix to the interface radio. assignment of an address to the British Virgin Islands and setting a value default gateway on the device and you should be able to raise it.

• Point of access Cisco Aironet 1200 series help

  We have 4 Cisco Aironet 1200 Access Points and they are all set to authenticate with our RADIUS server. However, authentication is hooked and can't understand why. Does anyone have any knowledge/experience with Cisco Aironet 1200 Access Points configuration?

  OK, I do not work with the GUI so although the memory is a little hazy but from the APs home page look on the left hand side and there is an option for something like "Software Setup" or something to that effect. You should be able to find the IOS version of here. This requires that you are indeed runnig IOS code. How old are these APs? If more than a few years ago (and perhaps even more recent) that they could very well be running VxWorks and then we are in a different ball game. If you see what I have described above and the homepage for the AP is often white with a bit of greenish-blue, bluish-green color then IOS, if it is more colorful, yellow stuff and VxWOrks.

  I hope this helps. Let me know if you need anything that anyone else. I will try to answer as soon as POSSIBLE.

• Cisco Aironet 1131AG and measure access points to the power of the wireless signal?

  / * Style definitions * / table. MsoNormalTable {mso-style-name : « Table Normal » ; mso-tstyle-rowband-taille : 0 ; mso-tstyle-colband-taille : 0 ; mso-style-noshow:yes ; mso-style-priorité : 99 ; mso-style-qformat:yes ; mso-style-parent : » « ;" mso-rembourrage-alt : 0 à 5.4pt 0 à 5.4pt ; mso-para-marge-top : 0 ; mso-para-marge-droit : 0 ; mso-para-marge-bas : 10.0pt ; mso-para-marge-left : 0 ; ligne-hauteur : 115 % ; mso-pagination : widow-orphelin ; police-taille : 11.0pt ; famille de police : « Calibri », « sans-serif » ; mso-ascii-font-family : Calibri ; mso-ascii-theme-font : minor-latin ; mso-hansi-font-family : Calibri ; mso-hansi-theme-font : minor-latin ;}

  / * Style definitions * / table. MsoNormalTable {mso-style-name : « Table Normal » ; mso-tstyle-rowband-taille : 0 ; mso-tstyle-colband-taille : 0 ; mso-style-noshow:yes ; mso-style-priorité : 99 ; mso-style-qformat:yes ; mso-style-parent : » « ;" mso-rembourrage-alt : 0 à 5.4pt 0 à 5.4pt ; mso-para-marge-top : 0 ; mso-para-marge-droit : 0 ; mso-para-marge-bas : 10.0pt ; mso-para-marge-left : 0 ; ligne-hauteur : 115 % ; mso-pagination : widow-orphelin ; police-taille : 11.0pt ; famille de police : « Calibri », « sans-serif » ; mso-ascii-font-family : Calibri ; mso-ascii-theme-font : minor-latin ; mso-hansi-font-family : Calibri ; mso-hansi-theme-font : minor-latin ;}

  We have about forty points of access Cisco Aironet 1131AG spread over four floors and they all have a static IP (BVI1) on the same SSID, customers will be on its own virtual local area network (dhcp on 3750 switch) and they use several channels (1,6,11).  Cisco Wireless Control System is pending. This wireless network should support roaming for customers (there will be Wi - Fi tags of multiple AeroScout and wireless laptops). To measure the strength of the wireless signal and wireless coverage on each floor. My questions are:

  1. How to measure the strength of the wireless signal: we must meet at least three APs available with signal excellent (I guess for the WCS needs that will determine the position of the client in the building)? We thought to use NetStumbler and a few laptops with wifi and measure as many points as we can as simpler thing. Or should we use something like Cisco Aironet Client adapters for our mobile phone and then use Cisco Aironet Client Utility (is it worth buying for our analysis and measurement)? Any other idea?
  2. What signal level should we consider for a good wireless (dBm)?
  3. That we should propose for authentication, authorization and management accounting? What happens to the roaming wireless? I did not quiteunderstand WCS, WDS and WLC-that should be used for above tasks?

  Thanks in advance.

  "Use the command on the AP" sh dot11 associations "will give you the clients associated with success.  If you add the MAC address of the client at the end of the command, you will get detailed information.  Look under "Signal Strength" and "Signal to noise".  Under the strength of the Signal, you want a value of-75 dBm or lower (lower values the better).  -76 dBm and is bad.  Under Signal-noise, you want a value of 25 dBm or more (values higher the better).

  To measure the strength of the signal, I use Airmagnet, but you can use Netstumbler or Cisco Wireless Site Survey.

• Cisco Aironet 1140 Standalone AP

  Greetings. For some time I'm looking for bargains from a class wireless access point. I narrowed down it to the stand-alone Cisco Aironet 1140 (no controller). I'm no stranger to Cisco products. I worked with the routers, switches and firewalls Pix / ASA. However, I did not have the opportunity to work with their wireless access point I hope that someone here who has experience using these AP (more precisely the autonomous 1140), can provide information on the reliability and safety of these devices. Some of the features that I would like to have as Mgmt. Radio and Rogue AP Detection I see are only available on the controller base units. Do not have these features on the autonomous unit reduced its reliability and safety? It's for a small business and the budget does not drop to a controller at this time. Thank you!

  The 1140's are a good choice for standalone 802.11n. Regarding reliability and safety, it would be identical to a lightweight AP. you can use different types of encryption as well as using 802.1 x. You will not not reliable detection functions or management of radio since these are autonomous.

  Thank you

  Scott Fella

  Sent from my iPhone

• Create the Pool DHCP on Cisco Aironet 1131AG

  Hello

  How to create a DHCP on a Cisco Aironet pool so that laptops could get an IP address from this range when connected?

  I don't want to use DHCP on our servers because these laptops are to be on a separate network.

  Just do not know what commands to use.

  Thank you!

  Hello

  There is a nice step by step to configure the DHCP Service on the AP in this doc;

  Configuration of the Access Point to provide DHCP Service

  http://www.Cisco.com/en/us/docs/wireless/access_point/12.3_8_JA/configuration/guide/s38adm.html#wp1090319

  I hope this helps!

  Rob

  Thank you to support CSC helps Haiti

  https://supportforums.Cisco.com/docs/doc-8895

  https://supportforums.Cisco.com/docs/doc-8727

• Impossible to find a stand-alone image for Cisco Aironet 1140

  Can someone give a link?

  -JeIlMa

  Here you go:

  http://tools.cisco.com/support/downloads/go/PlatformList.x?sftType=IOS+Software&mdfid=282439881&treeName=Wireless&mdfLevel=Model&url=null&modelName=Cisco+Aironet+1140+Access+Point&isPlatform=N&treeMdfId=278875243&modifmdfid=null&imname=&hybrid=Y&imst=N