Cisco SG300-10 Cisco 6513 and Shoretel phones

Similar Questions

• Connection Cisco SG300-10-Core Cisco 6513 for ShoreTel phones

  I have a new ShoreTel phone system will soon.  Configure a dhcp, including option 156 scope which is required for ShoreTel to obtain the configuration on ShoreTel phones and in order to get on the vlan correct voice on the phone.  I also created a new vlan 112 for the vlan voice.  When I plug directly into the Cisco 6513 Core switch, the phone starts fine, it gets its configuration and on the VLAN correct 112.

  We have a training room in which there will be a lot of users.  I ordered 6 Cisco small business 10port SG-300 POE switches for this training room.  I plugged the switch in a cable coming off the 6513 which is just an access port and in the vlan voice I created for phones shoretel VOIP:

  interface FastEthernet10/11
  switchport
  switchport mode access
  switchport voice vlan 112
  priority queue queue-limit 20
  WRR-queue random - detect min-threshold 1 30 40 50 60 70 80 90 100
  WRR-queue random - detect min-threshold 2 30 40 50 60 70 80 90 100
  WRR-queue random detection threshold min 3 30 40 50 60 70 80 90 100
  WRR-queue random detection max-threshold 1 70 80 90 100 100 100 100 100
  WRR-queue random detection max-threshold 2 70 80 90 100 100 100 100 100
  WRR-queue random detection threshold 3 70 80 90 100 100 100 100 100 max
  WRR-queue cos-map 1-3-1
  WRR-queue cos-1 6 4 map
  WRR-queue cos-map 2 6 0
  WRR-queue cos-map 2 8 2
  WRR-queue cos-map 3 1 7
  WRR-queue cos-map 3 8 3 6
  MLS qos trust dscp
  Storm-control broadcasts 20 h 00
  spanning tree portfast

  When I plug a phone directly into this cable the phone works very well.  When I plug a cheap cisco POE switch in I can get 3 phones works very well, but due to the amount of energy needed for this cheap a cisco switch it will give only 3 phones power.

  The real problem here is plug into small business cisco SG300-10port POE managed switch.  I thought I could just connect the switch to the port configured above right out of the box and plug in phones without a problem.  When I plug the switch and start plugging in ShoreTel phones, they do not start coming in and upward and actually had a few phones upward but then finally there is no tone and also later, they appear on the screen as a service not available.

  I have to configure a trunk port on a port on the SG300 and the Cisco 6513 for this to work?  Also I will need to VLAN configuration manually on the SG300.  Looks like that when I just plugged it in to the above configured the port on the SG300 it automatically create the vlan 112.

  Any help would be appreciated

  Thank you

  Dave

  Deleted

• Creation of trunk of Cisco 6513 to Cisco SG300 - 10 p for Shoretel phones

  I plugged a new Cisco SG300 - 10 p in an access on our Cisco 6513 port, which is in vtp mode.  I think I will need to create a trunk port of the Cisco SG300 - 10 p 6513, to carry out my office data vlan 1 and my new vlan 112 shoretel VOIP.  I believe that some how all ports are in mode trunk on the default sg300.  I have attached a picture of what it looks like on the management area of vlan sg300.  For some reason any I can plug 3 phones in the sg300 currently just plugged in the 6513 access port and one of the 3 phones come with the vlan voip good 112 and goes into the service very good.  The other 2 phones come but show no service, until I closed the port on sg300 for these other 2 phones and then put the ports back up, then the phones go up.  All of this without going through the port on the Cisco 6513 as a trunk port, it is only now as an access port vlan 1 data and vlan 112 voip vlan.

  My question is, should I put the cisco 6513 in trunk mode and the sg300 will attempt to become the server in vtp and ruin my entire network.  This is what scares me, because I've heard the horror stories of what happens.  My other question is if I have to put the port in trunk mode on him going the sg300 6513, it causes all future phones at the same time without problems?  What would be the cause of 1 of the 3 phones to come as they do and 2 others to come after stop int and put it up?

  Thanks Dave

  Double post.

  Go HERE.

• Cisco VCS and integration Lync2013

  Hello!

  Could you tell me please, when CISCO officially support Lync2013 - free new software for VCS - C and documentation on integration?

  The main interest is the possibility of transferring video between CISCO/MCU and Lync endpoints on the H.264 Protocol, who hails from Lync2013.

  Right now, I've got VCS - C and RTM Lync2013 X7.2. During the video call without AMGW appeal established as audio only.

  When using with Lync2010, it worked on Protocol H.263 and CIF resolution.

  Evgeniy salvation,

  We are currently investigating the possibilities to achieve interoperability between Lync 2013, VCS and video devices on the side of the VCS standards-based, it is a work in progress and at this stage, it is to early to provide any factual information on when interop will be available.

  In contrast to Lync 2010, Lync 2013 does not support H.263 for video and it so that will remove the OCS/Lync integration. I do however think that you should be able to make a two-way video between Lync 2013 and VCS-joined endpoints if you use an AMGW tried that yet?

  Thank you

  Andreas

• Backdoor in Cisco routers and firewalls.

  The more I read on the NSA scandal (and Yes, I apparently a scandal) less I trust corporations hardware and software.  There is no reason for anyone to doubt that all Cisco equipment comes with a backdoor.  Because these probable backdoors exist it's a matter of time before hackers discover and exploit them.  It's happened to Microsoft a number of times and there is no reason that it could not happen to Cisco.  It is no longer our trust Cisco equipment and have already started researching alternatives network.

  It is more a crazy conspiracy theory, that is the reality.

  In all liklihood, we use a series of firewall to further isolate our network against intrusions.  To reduce costs, we can keep our existing in this topology Cisco equipment, but we will replace hardware Cisco when it breaks down or needs to be upgraded.  I do the same thing with my home network.

  In the last months, we already moved all of our e-mail to secure servers overseas and changed all our McAfee, AVG and Avast antivirus software.  We are also researching Linux distributions to replace Microsoft.

  If Cisco wants to protect their brand, they need to take a stand or see their market share continue to erode.  There must be a CEO to a U.S. company that will take this position and be a hero rather that continue to be a lap dog.

  Hello

  use open-source based linux firewalls and routers.

  and check the source cod

• Cisco show and share to publish on the internet

  Dear Experts

  We have new deployment for Cisco SNS, and we publish SNS on the internet. I need help to do it and any recommendations, please.

  Thank you

  Richard

  Hi Richard

  Solve you your problem? I have to make sure of the following.

  1. you can access external SNS internally.

  2-natting is ok between IP Public & private.

  3. for the DNS record, make sure that the name must be the same on the inside & outside. For example internlly vod.bnp.med.ca and create a record public vod.bnp.med.ca should be the same FQDN, otherwise your SNS will never work. For authentication, you must publish the DMM.

  Note: your question this internal FQDN differs from the external FQDN of the SNS.

  Thank you

  Please note all relevant information

• Cisco ISE and Meraki RADIUS

  I am very new to Cisco ISE and Meraki.  I try to get the Radius configuration for wireless authentication.  When I do a test of the Meraki to ISE, it passes.

  When I try to connect from my laptop, I look at the logs of the Radius and it passes; However, it does not connect me to good policy.  I keep hitting the default policy.  I have my Meraki police above the default policy in the strategy defined in article.  I have attached what looks like my strategy game.

  Devices does not really matter. Here is what I see when I create a device group (where you add the access point to this group), and then create the condition:

  networkdevicegroups.PNG

  

  And here is where I create the condition of strategy game and you should be able to select the Meraki access points:

  devicecondition.PNG

  

  This will give you the condition similar to what I posted above. This is perhaps why you aren't hit that is not matching the condition for this game.

• AAA Cisco 600 and 700

  Cisco ACS GANYMEDE + AAA can be activated for telnet to Cisco 600 and 700 routers?

  Unfortunately you can not configure radius AAA or Ganymede in routers series 600 or 700.

• The traffic load between the power of Cisco ASA and FireSight Management Center fire

  Hi all

  I have a stupid question to ask.

  Can I know what is the traffic load and the e/s flow between firepower Cisco ASA and FireSight Management Center?

  Currently working on a project, client require such information to adapt to their network. Tried to find in the document from Cisco, but no luck.

  Maybe you all have no idea to provide.

  It varies depending on the number of events reported from the module to the CSP. No event = only health controls and policy changes are exchanged. 10,000 events per second = much more traffic.

  Generally it is not a heavy load, however.

• Configure to integrate Cisco ASA and JOINT

  Hello

  We have Cisco ASA and JOINT, need assistance on the integration of the same thing; Please email me so that I'll share the details of the architecture.

  Thank you best regards &,.

  REDA

  Hi reda,.

  If I correctly your diagram, you do not want to send any traffic from the external switch to the JOINT with a SPAN port and all traffic from your DMZ interfaces with another.

  Is this correct?

  If so, can you tell me why you want to inspect the traffic before it goes through the firewall? As I said in my original answer, we generally advise putting IP addresses after the firewall.

  Not to mention that in your case, I guess that some traffic will be inspected twice so you will need to assign a different virtual sensors to each JOINT internal interfaces to ensure that the same instance does not see the traffic of several times.

  Kind regards

  Nicolas

• What is the difference between Cisco NAC and ACS?

  I am currently part of a new construction project and my Cisco account manager and sales engineer recommend Cisco NAC for our new MDF. I'm confused because I don't clearly know the difference between a Cisco ACS and the NAC. What is the difference?

  Thank you

  Chris

  Chris,

  The two are completely different, maybe the sales rep could present you with more information and application. Each offers a variety of services tailored to the specific needs. I think that we need to read more in depth on the proceeds of the NAC. NAC seems an excellent solution for authentication authorization but other regulatory compliance.

  When you see ask your representative to sales for more information/demo.

  ACS is more widely use as a central point to access control to network devices routers, an example is for acs accounting management and the authority to order on all devices on the network using acs as RADIUS server. Considering that the NAC is over a central point of safety inspection on earlier systems of access to your network by via LAN or outside, an example of these respected regulatory defined could be inspections could be virus definition checks before getting lan access thus preventing access to the LAN if the system does not have regulatory compliance defined in NAC access is denied. Another example could be the unknown local host connections etc... So, it seems that NAC is a much broader product that provides endpoint security internal, not only the authentication authorization as acs... ACS has been there for a long time, NAC is rather new product.

  NAC

  http://www.Cisco.com/en/us/NetSol/ns466/networking_solutions_package.html

  http://www.Cisco.com/en/us/solutions/collateral/ns340/ns394/ns171/ns466/ns617/net_qanda0900aecd800fdd6f_ns466_Networking_Solutions_Q_and_A.html

  ACS

  http://www.Cisco.com/en/us/products/sw/secursw/ps5338/index.html

  Rgds

  Jorge

• Turn on the mtu on cisco switch and cisco user server

  Hi all

  someone got bad luck turning on the mtu on their cisco switch?  I guess I need to turn it on for all because the command is for all ports on cisco catalyst and my server switch is nearby to my user of switches and a broadband bandwidth 6 G or 6 ports, I need to turn it on for all user ports?

  Thanks for any comments, that you can add.

  I assume you mean Jumbo frame support! You shouldn't have any problems with that. Please take a look at for example http://www.cisco.com/en/US/products/hw/switches/ps700/products_configuration_example09186a008010edab.shtml for more details and the configuration of the different switches. According to the model, the parameters are for dedicated ports only or the entire switch. In the case of the switch everything you will need to reload (reboot) switch, so be careful.

  André

• 7925 problems of compatibility of end of sale and 8821 phone wireless

  I support approximately 700 strongly Cisco 7925 G wireless phones used in our environment. Now that Cisco is suddenly their progressive, with the end of the sale in October, for the 8821 what are we left with some dilemmas that can potentially be very costly.  I was not able to find a lot of documentation either.  First of all, are office charging stations and a multi-line 7925 8821 phones-compatible phone?  Second, are batteries interchangeable 7925 and 8821?  Thirdly, the data sheet 8821 says its compatible with CUCM 9.1 (2) and later.  What this means that they will not work in my 8.5.1 environment?  Finally, the data sheet indicates the minimum version supported access point 7.0.250. What are the consequences if I access points with lower versions, like 7.0.235.3 or 7.0.240.0?

  Does anyone have an entry or advise? It's greatly appreciated.  Thank you.

  Can anyone confirm, but I believe that charging stations or the batteries are compatible, if someone already has them both in their environment, feel free to correct me if I'm wrong.

  As for the version, Yes, will not work on your version 8.x because they require 9.1 2 to work.

• Change the apple to my e-mail ID unique and new phone number

  I have an iPhone 6, bought in the United States in December 2015. The registered apple ID my phone number is connected to the apple of my husband ID. I live in a different country, I have my own email address, and I have a new phone number. How can I change the apple on my phone ID to reflect this new information?

  I'm not Matt brownson, I have my own phone and own phone number, own enamel. I want my iPhone to be entered under my new information.

• MY DROP of CALLS AND MY PHONE SAYS NO SERVICE, BUT I HAVE SERVICE

  MY DROP of CALLS AND MY PHONE SAYS NO SERVICE, BUT I don't HAVE SERVICE. HOW CAN I SOLVE THIS PROBLEM?

  < re-titled by host >

  Hello

  Follow the steps here:

  If you cannot connect to a cellular network or cellular data - Apple Support