CISCO WIRELESS SOLUTION

Similar Questions

• Is it possible to use a Linksys by Cisco Wireless - G Internet home monitoring camera with Labview

  I was wondering if it is possible to use a "Linksys by Cisco Wireless - G Internet home monitoring Camera" with Labview

  http://www.dabs.com/ProductView.aspx?quicklinx=53PX&SearchType=1&searchTerms=network+cameras&PageMod...

  I wan't to be able to get the raw data from the camera and analyze it.

  I found a simple soloution to this problem,

  Is possible to use a web browsers invoke node basically give a screenshot of the web page (get image)

  It can then be loaded into a display of the image and will show exactly what the web browser is showing and can also be analised by unflattening the pixmap.

  Maybe it's not the most effective method, but he turns my rig fast enough and does the job

  It may also be a setting value of the display of the photo to "smooth updates" that gets rid flashes white as the changes to the image, if anyone else has this problem.

• Cisco Wireless-N bridge for phone adapters firmware update problem

  Hello

  I have a bridge for phone adapters N of Cisco wireless. I decided to update the firmware on the device. I downloaded it from the official website of Cisco download page. So I've just connected to the device and started the update procedure. I waited for the right amount of time allowing the aircraft to install a new firmware.

  Now the wireless bridge will not start. Once powered up system LED will blink green for 15 seconds. Then it will become orange and flashes with a frequency higher than forever.

  I tried factory reset, but it does not work: same behavior remains.

  As a note - I have updated exactly same device with exactly same firmware just before I did this and it went good - firmware is not a reason for this behavior.

  Can anyone advice me on what I can do to give life to this device?

  Hi Nikolai,

  If the unit is still under warranty I suggest you to contact Small Business Support Center and open the ticket as most likely the replacement is necessary:

  http://www.Cisco.com/c/en/us/support/Web/TSD-Cisco-small-business-suppor...

  Kind regards

  Aleksandra

• Are Cisco 1130ag APs compatible with Cisco Wireless LAN Controller virtual?

  Are Cisco 1130ag APs compatible with Cisco Wireless LAN Controller virtual?

  It's... AP compatibility depends on the code that runs on the WLC. This is a matrix that is a good reference.

  http://www.Cisco.com/en/us/docs/wireless/controller/5500/tech_notes/wire...

  Sent by Cisco Support technique iPhone App

• Adding printers Wireless Solution Center

  I am running Win7 and after restarting my wireless network, wireless (Photosmart C7250 Photosmart Premium C410a) printers have been added in windows using the window adds a printer.  Now, the HP Solution Center does not see wireless printers.  Is there an easy way to add them to the center of solution since they are on the network (with a different IPv4 address of initial installation)?

  Look in your Start menu all programs for the HP folder with printer software. You should see an option "add a printer". To avoid this problem in the future I would set a static ip address for the printer.

  http://h30434.www3.HP.com/T5/printer-networking-and-wireless/static-IP-address/TD-p/1663045

• Failure of wireless solution Center

  Solution Center does not connect to D 110 series wireless printer.  I can print from other programs wireless.  Solution Center connects via a USB connection. Windows 7.  I can't find the original software disk

  How did you initially installed the printer first, USB or wireless?

  Uninstall the HP software. When you reinstall the drivers and full software features, select Wireless. After this download and install and you print, then go to plug in the USB cable.

• Cisco Wireless router model WRT120N guard give up Internet connection

  My wireless router will work for 6-8 hours, and then remove the connection to the internet.   I switch the modem and the router several times to re-establish the connection.  I'm also using a Netgear Access Point.

  I use:

  Charter high-speed Internet

  Motorola Modem

  Model Cisco WRT120N router

  Parameters

  Mixed-mode

  Channel Auto width - 20 MHz or 40 MHz

  Security - Personal WPA2

  Disabled SSID broadcast

  Firmware Version v1.0.04

  Automatic connection Type - Conf DHCP

  Beacon interval - 50

  Fragmentation threshold 2304

  RTS threshold 2304

  All other settings are default.

  When I unplug the modem to the router and plug it on the desktop I have internet service.

  The connection is also falling only on wired or wireless?

  Try to update the firmware on your router.
  Connect to the computer with the Ethernet cable to the router.
  Download the latest firmware from the site Web of Linksys and save it to your computer. Open the router configuration page. Click the Administration tab and switch to the sub tab upgrade the Firmware through the firmware file that you have already downloaded and update on your router.
  After upgrading the firmware on the router, it is recommended that you must reset the router and reconfigure. Press and hold the reset button on the router for 30 seconds. Release the reset button and wait 10 seconds. Power cycle the router and reconfigure.

• Cisco Wireless Lan Controller 2504

  Hello:

  Hello; I lost the password to my wireless LAN controller. Everything was fine until a few days ago and now can not identify.
  Is it possible to recover. The model of controller is AIR-CAP2602E-A-K9, the software version is 7.4.110.0.

  Please, anyone, help me.

  Kind regards.

  Fernando.

  Check this box:

  http://www.my80211.com/Cisco-WLC-CLI-commands/2009/12/27/recover-your-WL...

  Concerning

  Remember messages useful rates

• Version of the software Cisco Wireless LAN controllers & Licensing (controllers HA and APs Adder & licenses basic questions)

  In fact, one of my clients has two Cisco 5508 wireless LAN controllers installed in a site and back up and running now. one of them running software version 7.4 and the other running software version 7.6. Each of them works as a stand-alone controller with number of access points. Based on this scenario, answer below concerns:

  • Can we transfer all active licenses at one of them and use it as a HA free of charge?

  • Up to which version of the software, we can improve these controllers without any extra charge?

  • What we must do if we want to move two of them to version 8 software?

  Waiting to hear from you soon about my concerns.

  Here are a few notes:

  -Only licenses Adder can be reheberges to another controller. Base license cannot be rehosted unless the unit is THAT RMA would be.

  -Too long the WLC has a minimum of 50 access point license, so that the unit can be used for HA N + 1 or AP SSO.

  s ' it use SSO of AP, the WLC must have connections to subnets for layer 2 even due to the IP address of the interface.

  HA N + 1 can be used in sites different especially if the subnet do not align

  -Scott

• Software for laptops new Cisco wireless card

  Given that the new laptops have more the PCMCIA slots and Cisco does not sell a compatible card, at least no I can find, will be their tool of survey construction with integrated maps?  I need to do a site survey for the implementation of a MESH and do not have the software more, mine succumbs to a terrible death.

  will their site survey tool work with the built in cards?

  N °

  You want to create a fancy report?  If Yes, then your next stop will be Airmagnet Wireless Site Survey of Fluke

  If the answer is no, then a simple proggie as Netstumbler and inSSIDer will be sufficient.

• Cisco Wireless - E2500 N Dual Band router and hide the SSID

  Hello

  I tried to hide my SSID by allowing emissions the SSID of the first, and then the other band.

  Once I have say-activated the SSID broadcast of the last band my laptop, which has the wireless card, would lose connection to the internet on reboot.

  I read somewhere, but now can't find the article, you can hide those SSID, but it requires some work to connect to a network that is more diffuse.

  Someone has knowledge on how to go about this, or maybe they could point me to a resource that explains how to set this up... thanks.

  Tom.

  The properties of the wireless network. Check "Connect even if this network is not broadcast".

• Center of Cisco IP solutions - error reporting, jobs SR manually removing from cli, Autostart ISC after startup

  Hello

  1. I get the following error when you run a report;

  * Unable to create the report. The following errors occurred:
  1: NBI reports the connection has failed. Invalid security identification information

  What could be the problem?

  2. How can I create custom reports? Creates the only way XML files?

  3. How can I remove pools of resources or jobs manually OS cli?

  4. is it possible to auto start ISC when the server restarts?

  Hello

  For 1. It is perhaps a license problem (NBI licenses), which version are you? I've heard reports are enabled by default on 6.0, but not sure.

  For 2. Look at http://www.cisco.com/en/US/docs/net_mgmt/ip_solution_center/6.0/infrastructure/reference/guide/monit1.html#wp1229130 . I think that xml is the only way, even if you use directly the xmlapi.

  3. I don't know if this is even possible. You can do this with the nbi and xmlapi.

  For 4. Look at the symptom of http://www.cisco.com/en/US/docs/net_mgmt/ip_solution_center/6.0/installation/guide/aptrbl.html#wp1032457 6.

  Hope I helped.

• Upgrade of Cisco Wireless Controller 4402

  We have a 4402 WLAN controller with a bunch of AP in 6 locations. The software is installed on a Windows Server 2003 server - since our society must be in accordance with various compliance agencies, we are in the process of getting rid of all 2003 servers in our infrastructure as they will be supported are more early next year.

  I created a new server (2012 R2) and tried to install, but get the error that it is only supported on Server 2003 or Red Hat.

  Is there a way to get this installed on one different platform other than 2003?

  Thank you!

  Yes, you can keep the same equipment (WLCs and AP).

  I was just saying about upgradation WCS to the CNS / prime infrastructure

  NCC/WCS are just a management for wireless LAN controllers APs. so if you change the WCS to the CNS, then it will affect any service.

  Concerning

  Remember messages useful rates

• Replacement of Cisco ACS Solutions 4.2 engine

  Hello

  Our ACS (Cisco 1113) is dead and it is not cost-effective to replace because it will serve only until the end of this year.

  Is it possible to get the Ganymede software to install on a Windows Server? How can I go on the procurement software as the original documentation is no longer available? The fact that I have a dead unit will be sufficient evidence for a copy of the software? We are currently running v4.1

  Thank you.

  Here's a path to download the Eval of ACS 4.2 windows.

  Cisco.com > downloads Home > Products > Security > access control and

  Policies > policy and access management > Cisco Secure Access Control

  Server for Windows > Cisco Secure ACS for Windows 4.2 > secure access

  Control (ACS) server for Windows - 4.2.0.124 > scroll down

  and you will see a file named

  ACS v4.2.0.124 90-Days Evaluation Software

  EVAL-ACS - 4.2.0.124 - SW.zip

  ACS installation under windows

  http://www.Cisco.com/en/us/docs/net_mgmt/cisco_secure_access_control_server_for_windows/4.2/installation/guide/Windows/install.html

  Once installed, you can restore the previous backup on windows server.

  Restore from a backup ACS file

  http://www.Cisco.com/en/us/docs/net_mgmt/cisco_secure_access_control_server_for_windows/4.2.1/User_Guide/SCBasic.html#wp222758

  Jatin kone

  -Does the rate of useful messages-

• HP - Officejet 4500n wireless solutions Center

  Hi all

  Currently get:

  error analysis in the file (x 86) \hp\digital imaging\bin\hpqscloc\1033.xml

  8, 64 - bit Windows.  I tried uninstalling and reinstalling, and also the restoration of the system.

  Cannot be resolved.

  Any help greatly appreciated.

  Please follow the steps below. Normally, I would like a link to the printing software, however, I do not know which printer everyone uses.

  Of the Original installation CD:

  1. Insert the CD in the drive and then cancel Setup

  2. open my computer and click right then on the CD from the drive and select open

  3 open the Util folder

  4 open the CCC folder

  5 enforce in the L4uninstall.exe (IF not HP computer, if computer HP function L3uninstall)

  6. once the uninstall is complete, restart the computer

  7 run the Accessories\ System Tools Disk Cleanup

  8. download and install the latest version of Adobe flash player

  http://www.Adobe.com/support/flashplayer/downloads.html

  9 download drivers and full software features

  Enter your printer model and go to software downloads & pilot

  10. run the download to reinstall the printer

  If the software has been downloaded and extracted to your system:

  1. type % temp % in the field of race

  2. Locate and open the folder starting with 7z (example: 7zS2356)

  3 open the Util folder

  4 open the CCC folder

  5 enforce in the L4uninstall.exe (IF not HP computer, if computer HP function L3uninstall)

  6. once the uninstall is complete, restart the computer

  7 run the Accessories\ System Tools Disk Cleanup

  8. download and install the latest version of Adobe flash player

  http://www.Adobe.com/support/flashplayer/downloads.html

  9 download drivers and full software features

  Enter your printer model and go to software downloads & pilot

  10. run the download to reinstall the printer