Client VPN router IOS does not connect
Hi all
I'm having some trouble of Client VPN connection over the internet to our Cisco IOS router. Some help would be very appreciated!
On the VPN client log I get the following error messages:
---------------------------
...
573 16:32:13.164 21/12/05 Sev = WARNING/2 IKE/0xE3000099
Size invalid SPI (PayloadNotify:116)
574 16:32:13.164 21/12/05 Sev = Info/4 IKE/0xE30000A4
Invalid payload: said length of payload, 568, not enough Notification:(PayloadList:149)
575 16:32:13.164 21/12/05 Sev = WARNING/3 IKE/0xA3000058
Received incorrect message or negotiation is no longer active (message id: 0x00000000)
---------------------------
We get debugging on the router that I'm trying to connect:
---------------------------
router #debug isakmp crypto
...
21 Dec 16:32:16.089 AEDT: ISAKMP (0:0): received 203.153.196.1 packet dport 500 sport 500 SA NEW Global (N)
21 Dec 16:32:16.089 AEDT: ISAKMP: created a struct peer 203.153.196.1, peer port 500
21 Dec 16:32:16.089 AEDT: ISAKMP: new created position = 0x678939E0 peer_handle = 0 x 80000031
21 Dec 16:32:16.089 AEDT: ISAKMP: lock struct 0x678939E0, refcount IKE peer 1 for crypto_isakmp_process_block
21 Dec 16:32:16.089 AEDT: ISAKMP: 500 local port, remote port 500
21 Dec 16:32:16.089 AEDT: insert his with his 67B0AB34 = success
21 Dec 16:32:16.089 AEDT: ISAKMP: (0:0:N / A:0): treatment ITS payload. Message ID = 0
21 Dec 16:32:16.089 AEDT: ISAKMP: (0:0:N / A:0): payload ID for treatment. Message ID = 0
21 Dec 16:32:16.089 AEDT: ISAKMP (0:0): payload ID
next payload: 13
type: 11
ID of the Group: eggs
Protocol: 17
Port: 500
Length: 12
21 Dec 16:32:16.089 AEDT: ISAKMP: (0:0:N / A:0): peer games * no * profiles
21 Dec 16:32:16.089 AEDT: ISAKMP: (0:0:N / A:0): load useful vendor id of treatment
21 Dec 16:32:16.089 AEDT: ISAKMP: (0:0:N / A:0): supplier code seems the unit/DPD but major incompatibility of 215
21 Dec 16:32:16.089 AEDT: ISAKMP: (0:0:N / A:0): provider ID is XAUTH
21 Dec 16:32:16.089 AEDT: ISAKMP: (0:0:N / A:0): load useful vendor id of treatment
21 Dec 16:32:16.089 AEDT: ISAKMP: (0:0:N / A:0): provider ID is DPD
21 Dec 16:32:16.089 AEDT: ISAKMP: (0:0:N / A:0): load useful vendor id of treatment
21 Dec 16:32:16.089 AEDT: ISAKMP: (0:0:N / A:0): supplier code seems the unit/DPD but major incompatibility of 194
21 Dec 16:32:16.089 AEDT: ISAKMP: (0:0:N / A:0): load useful vendor id of treatment
21 Dec 16:32:16.089 AEDT: ISAKMP: (0:0:N / A:0): supplier code seems the unit/DPD but major incompatibility of 123
21 Dec 16:32:16.089 AEDT: ISAKMP: (0:0:N / A:0): provider ID is NAT - T v2
21 Dec 16:32:16.089 AEDT: ISAKMP: (0:0:N / A:0): load useful vendor id of treatment
21 Dec 16:32:16.089 AEDT: ISAKMP: (0:0:N / A:0): provider ID is the unit
21 Dec 16:32:16.089 AEDT: ISAKMP: analysis of the profiles for xauth...
.....
21 Dec 16:32:16.093 AEDT: ISAKMP: (0:0:N / A:0): atts are not acceptable. Next payload is 3
21 Dec 16:32:16.093 AEDT: ISAKMP: (0:0:N / A:0): audit ISAKMP transform 12 against the policy of priority 3
21 Dec 16:32:16.093 AEDT: ISAKMP: 3DES-CBC encryption
21 Dec 16:32:16.093 AEDT: ISAKMP: MD5 hash
21 Dec 16:32:16.093 AEDT: ISAKMP: group by default 2
21 Dec 16:32:16.093 AEDT: ISAKMP: pre-shared key auth
21 Dec 16:32:16.093 AEDT: ISAKMP: type of life in seconds
21 Dec 16:32:16.093 AEDT: ISAKMP: life (IPV) 0x0 0 x 20 0xC4 0x9B
21 Dec 16:32:16.093 AEDT: ISAKMP: (0:0:N / A:0): pre-shared authentication offered but does not match policy.
21 Dec 16:32:16.093 AEDT: ISAKMP: (0:0:N / A:0): atts are not acceptable. Next payload is 3
---------------------------
You can apply the encryption the WAN interface card and check?
Tags: Cisco Security
Similar Questions
-
Wireless printer Lexmark X 4850 and a netgear router that does not connect while I can print
Rookie PC user...
I have a Lexmark X 4850 wireless printer and a netgear router that does not connect while I can print ggggrrrr....!I checked all plugs and connections, the reboot several times and am about to throw it out the window... Help!Hello
Welcome to the Microsoft Community and thanks for posting the question.
According to the description, it looks like the wireless Lexmark X 4850 printer is not to connect to the wireless router.
Visit this link that should help you with this problem.
http://support.Lexmark.com/index?page=content&ID=FA697&locale=en&UserLocale=en
Note: Using third-party software or the link, including hardware drivers can cause serious problems that may prevent your computer from starting properly. Microsoft cannot guarantee that problems resulting from the use of third party software or link can be resolved. Using third-party software, or the link is at your own risk.
If this fails to resolve the problem, visit this link and read "need help?"
I hope this helps. If you have questions more related to Windows, feel free to post here at Microsoft Community.
-
Cisco VPN Client 5.0.0 does not connect
Hello
I am trying to establish the VPN session the firewall to 5525 X Cisco ASA crossing 9.1.1 Cisco VPN Client. Although AnyConnect is the way to go, the inherited method must always be supported for some time as part of a migration. I tried two VPN users (authenticated by ad) on two client computers running Windows 7 64 bit and Cisco VPN Client 5.0.07.0440. Both users are able to establish a session to a computer at the ASA, but not the other. Entering credentails evil, the login popup will appear immediately. On the combination of username/password correct name, the following VPN client log messages are generated and the session drops that is "not connected" in the status bar. The PCF file is the same on both client computers.
Cisco Systems VPN Client Version 5.0.07.0440
Copyright (C) 1998-2010 Cisco Systems, Inc. All Rights Reserved.
Client Type(s): Windows, WinNT
Running on: 6.1.7601 Service Pack 1
119 22:49:16.933 06/23/13 Sev=Info/6 IKE/0x6300003B
Attempting to establish a connection with 203.99.111.44.
120 22:49:16.939 06/23/13 Sev=Info/4 IKE/0x63000001
Starting IKE Phase 1 Negotiation
121 22:49:16.942 06/23/13 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK AG (SA, KE, NON, ID, VID(Xauth), VID(dpd), VID(Frag), VID(Nat-T), VID(Unity)) to 203.99.111.44
122 22:49:16.973 06/23/13 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = 203.99.111.44
123 22:49:16.973 06/23/13 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK AG (SA, KE, NON, ID, HASH, VID(Unity), VID(Xauth), VID(dpd), VID(Nat-T), NAT-D, NAT-D, VID(Frag), VID(?)) from 203.99.111.44
124 22:49:16.974 06/23/13 Sev=Info/5 IKE/0x63000001
Peer is a Cisco-Unity compliant peer
125 22:49:16.974 06/23/13 Sev=Info/5 IKE/0x63000001
Peer supports XAUTH
126 22:49:16.974 06/23/13 Sev=Info/5 IKE/0x63000001
Peer supports DPD
127 22:49:16.974 06/23/13 Sev=Info/5 IKE/0x63000001
Peer supports NAT-T
128 22:49:16.974 06/23/13 Sev=Info/5 IKE/0x63000001
Peer supports IKE fragmentation payloads
129 22:49:16.977 06/23/13 Sev=Info/6 IKE/0x63000001
IOS Vendor ID Contruction successful
130 22:49:16.977 06/23/13 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK AG *(HASH, NOTIFY:STATUS_INITIAL_CONTACT, NAT-D, NAT-D, VID(?), VID(Unity)) to 203.99.111.44
131 22:49:16.977 06/23/13 Sev=Info/6 IKE/0x63000055
Sent a keepalive on the IPSec SA
132 22:49:16.977 06/23/13 Sev=Info/4 IKE/0x63000083
IKE Port in use - Local Port = 0xCA7C, Remote Port = 0x1194
133 22:49:16.977 06/23/13 Sev=Info/5 IKE/0x63000072
Automatic NAT Detection Status:
Remote end is NOT behind a NAT device
This end IS behind a NAT device
134 22:49:17.000 06/23/13 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = 203.99.111.44
135 22:49:17.000 06/23/13 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK TRANS *(HASH, ATTR) from 203.99.111.44
136 22:49:17.211 06/23/13 Sev=Info/4 IPSEC/0x63700008
IPSec driver successfully started
137 22:49:17.211 06/23/13 Sev=Info/4 IPSEC/0x63700014
Deleted all keys
138 22:49:23.207 06/23/13 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK TRANS *(HASH, ATTR) to 203.99.111.44
139 22:49:23.393 06/23/13 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = 203.99.111.44
140 22:49:23.393 06/23/13 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK TRANS *(HASH, ATTR) from 203.99.111.44
141 22:49:23.393 06/23/13 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK TRANS *(HASH, ATTR) to 203.99.111.44
142 22:49:23.401 06/23/13 Sev=Info/5 IKE/0x6300005E
Client sending a firewall request to concentrator
143 22:49:23.401 06/23/13 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK TRANS *(HASH, ATTR) to 203.99.111.44
144 22:49:23.427 06/23/13 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = 203.99.111.44
145 22:49:23.427 06/23/13 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK TRANS *(HASH, ATTR) from 203.99.111.44
146 22:49:23.427 06/23/13 Sev=Info/5 IKE/0x63000010
MODE_CFG_REPLY: Attribute = INTERNAL_IPV4_ADDRESS: , value = 10.2.193.69
147 22:49:23.427 06/23/13 Sev=Info/5 IKE/0x63000010
MODE_CFG_REPLY: Attribute = INTERNAL_IPV4_DNS(1): , value = 10.2.5.2
148 22:49:23.428 06/23/13 Sev=Info/5 IKE/0x63000010
MODE_CFG_REPLY: Attribute = INTERNAL_IPV4_DNS(2): , value = 10.1.5.2
149 22:49:23.428 06/23/13 Sev=Info/5 IKE/0x6300000D
MODE_CFG_REPLY: Attribute = MODECFG_UNITY_SAVEPWD: , value = 0x00000000
150 22:49:23.428 06/23/13 Sev=Info/5 IKE/0x6300000D
MODE_CFG_REPLY: Attribute = MODECFG_UNITY_SPLIT_INCLUDE (# of split_nets), value = 0x00000001
151 22:49:23.428 06/23/13 Sev=Info/5 IKE/0x6300000F
SPLIT_NET #1
subnet = 10.0.0.0
mask = 255.0.0.0
protocol = 0
src port = 0
dest port=0
152 22:49:23.428 06/23/13 Sev=Info/5 IKE/0x6300000E
MODE_CFG_REPLY: Attribute = MODECFG_UNITY_DEFDOMAIN: , value = example.org
153 22:49:23.428 06/23/13 Sev=Info/5 IKE/0x6300000D
MODE_CFG_REPLY: Attribute = MODECFG_UNITY_PFS: , value = 0x00000000
154 22:49:23.428 06/23/13 Sev=Info/5 IKE/0x6300000E
MODE_CFG_REPLY: Attribute = APPLICATION_VERSION, value = Cisco Systems, Inc ASA5525 Version 9.1(1) built by builders on Wed 28-Nov-12 11:15 PST
155 22:49:23.428 06/23/13 Sev=Info/5 IKE/0x6300000D
MODE_CFG_REPLY: Attribute = MODECFG_UNITY_SMARTCARD_REMOVAL_DISCONNECT: , value = 0x00000001
156 22:49:23.428 06/23/13 Sev=Info/5 IKE/0x6300000D
MODE_CFG_REPLY: Attribute = Received and using NAT-T port number , value = 0x00001194
157 22:49:23.445 06/23/13 Sev=Info/4 IKE/0x63000056
Received a key request from Driver: Local IP = 10.2.193.69, GW IP = 203.99.111.44, Remote IP = 0.0.0.0
158 22:49:23.445 06/23/13 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK QM *(HASH, SA, NON, ID, ID) to 203.99.111.44
159 22:49:23.477 06/23/13 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = 203.99.111.44
160 22:49:23.477 06/23/13 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK INFO *(HASH, NOTIFY:STATUS_RESP_LIFETIME) from 203.99.111.44
161 22:49:23.477 06/23/13 Sev=Info/5 IKE/0x63000045
RESPONDER-LIFETIME notify has value of 86400 seconds
162 22:49:23.477 06/23/13 Sev=Info/5 IKE/0x63000047
This SA has already been alive for 7 seconds, setting expiry to 86393 seconds from now
163 22:49:23.477 06/23/13 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = 203.99.111.44
164 22:49:23.477 06/23/13 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK INFO *(HASH, NOTIFY:NO_PROPOSAL_CHOSEN) from 203.99.111.44
165 22:49:23.478 06/23/13 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK INFO *(HASH, DEL) to 203.99.111.44
166 22:49:23.478 06/23/13 Sev=Info/4 IKE/0x63000049
Discarding IPsec SA negotiation, MsgID=F3E3C530
167 22:49:23.478 06/23/13 Sev=Info/4 IKE/0x63000017
Marking IKE SA for deletion (I_Cookie=CD65262E1C3808E4 R_Cookie=912AE160ADADEE65) reason = DEL_REASON_IKE_NEG_FAILED
168 22:49:23.478 06/23/13 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = 203.99.111.44
169 22:49:23.479 06/23/13 Sev=Info/4 IKE/0x63000058
Received an ISAKMP message for a non-active SA, I_Cookie=CD65262E1C3808E4 R_Cookie=912AE160ADADEE65
170 22:49:23.479 06/23/13 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK INFO *(Dropped) from 203.99.111.44
171 22:49:24.310 06/23/13 Sev=Info/4 IPSEC/0x63700014
Deleted all keys
172 22:49:26.838 06/23/13 Sev=Info/4 IKE/0x6300004B
Discarding IKE SA negotiation (I_Cookie=CD65262E1C3808E4 R_Cookie=912AE160ADADEE65) reason = DEL_REASON_IKE_NEG_FAILED
173 22:49:26.849 06/23/13 Sev=Info/4 IKE/0x63000001
IKE received signal to terminate VPN connection
174 22:49:26.855 06/23/13 Sev=Info/4 IPSEC/0x63700014
Deleted all keys
175 22:49:26.855 06/23/13 Sev=Info/4 IPSEC/0x63700014
Deleted all keys
176 22:49:26.855 06/23/13 Sev=Info/4 IPSEC/0x63700014
Deleted all keys
177 22:49:26.855 06/23/13 Sev=Info/4 IPSEC/0x6370000A
IPSec driver successfully stopped
Any ideas why the second client of Windows 7 does not work?
Kind regards
Rick.
Rick
Thanks for the additional output. It shows the xauth authentication step, which is good to see. But it does not offer much clarity on what is causing the problem.
My attention is drawn to a couple of message on the balls that are in line with the two sessions for which you posted newspapers.
32 00:36:08.178 24/06/13 Sev = Info/5 IKE/0x6300005E
Customer address a request from firewall to hub
I'm not sure that we see any answer to this, but it makes me wonder if it is somehow involved in the issue. Is it possible that there is a difference in the configuration of firewall and operating between two clients?
I am also interested in this series of posts
48 00:36:08.210 24/06/13 Sev = Info/4 IKE / 0 x 63000056
Received a request from key driver: local IP = 10.2.193.69, GW IP = 203.99.111.44, Remote IP = 0.0.0.0
I don't know why the pilot requested a key at this point, and I wonder why the remote IP is 0.0.0.0?
It is followed by a package in which the ASA provides the value of the life of SA - which seems to be on the path to a successful connection. that is followed by
55 00:36:08.350 24/06/13 Sev = Info/5 IKE/0x6300002F
Received packet of ISAKMP: peer = 203.99.111.44
56 00:36:08.350 24/06/13 Sev = Info/4 IKE / 0 x 63000014
RECEIVING< isakmp="" oak="" info="" *(hash,="" notify:no_proposal_chosen)="" from="">
during which the SAA indicates that no proposal has been selected. It seems therefore that the ASA is not happy about something.
If we do not find indications of the client that allows to identify the problem, then maybe we look at the ASA. Are all log messages generated on the SAA during this attempt to establish VPN that could show us the problem? Would it not be possible to run debugs on the SAA in a trial of this machine?
HTH
Rick
-
I have a HP G60 Notebook PC with Windows Vista Home Premium, it is about 4 years old. I recently got a new Cisco Linksys E1500 wireless router, which is connected to my home computer. My laptop shows that it is connected to the home network, but it does not connect to the internet. Other laptops in the House are able to connect to the network and to the internet. Mine seems to be the only one not working do not. Why it is not working? What should I do about it?
I ran the network diagnostics. It is said "a problem with you network router or modem broadband could prevent an internet connection." I have disconnected these two and tried again. It did not work! I have also connected my laptop directly on the modem and it does not always connect to the internet. I tried to reset the network card. My IP settings are set to automatic.
My internet connection was not a problem before last week (when I got a new router). What is the problem with my computer? Help, please!
Hello:
If you have an Atheros wireless adapter in your PC and you have not updated the driver, I recommend that you install it.
Wireless adapters Atheros with former pilots, dislikes the new Linksys routers.
If you have an Atheros wireless card, and your wireless driver is more than 2 years, I am very confident that this will solve your connection problem.
Paul
-
Router Cisco client VPN SPlit tunnel does not work
Hello!
I have configured the Cisco VPN CLient on a 2821 router, and it works fine.
I could access the inside resourses normally >
the problem is that when I connect with VPN I lost internet connectivity?What wrong with my setup?
Below the current configuration of the router.
Kind regards!CISCO2821 #sh run
Building configuration...
Current configuration: 5834 bytes
!
version 12.4
horodateurs service debug datetime msec
Log service timestamps datetime msec
no password encryption service
!
hostname CISCO2821
!
boot-start-marker
start the flash c2800nm-adventerprisek9 - mz.124 - 20.T.bin system
boot-end-marker
!
forest-meter operation of syslog messages
logging buffered 51200 warnings
!
AAA new-model
!
!
connection local VPN-LOCAL-AUTHENTIC AAA authentication
local AAA authorization network VPN-LOCAL-AUTHOR
!
!
AAA - the id of the joint session
!
dot11 syslog
IP source-route
!
!
IP cef
!
!
"yourdomain.com" of the IP domain name
8.8.8.8 IP name-server
No ipv6 cef
!
Authenticated MultiLink bundle-name Panel
!
!
voice-card 0
No dspfarm
!
!
username secret privilege 0 vpn 5 $1$ tCf1$ XAxQWtDRYdfy9g3JpVSvZ.
Archives
The config log
hidekeys
!
!
crypto ISAKMP policy 44
BA aes
preshared authentication
Group 2
life 44444
!
ISAKMP crypto group configuration of VPN client
key VPNVPNVPN
VPN-pool
ACL VPN-ACL-SPLIT
Max-users 5000
!
!
ISAKMP crypto ISAKMP-VPN-profile
identity VPN group match
list of authentication of client VPN-LOCAL-AUTHENTIC
VPN-LOCAL-AUTHOR of ISAKMP authorization list.
client configuration address respond
Configuration of VPN client group
virtual-model 44
!
!
Crypto ipsec transform-set VPN - SET esp - aes esp-sha-hmac
!
Crypto ipsec VPN-profile
transformation-VPN-SET game
Set isakmp VPN ISAKMP-PROFILE
!
!
interface GigabitEthernet0/0
IP 192.168.2.214 255.255.255.0
NAT outside IP
IP virtual-reassembly
IP tcp adjust-mss 1412
automatic duplex
automatic speed
!
interface GigabitEthernet0/1
IP 192.168.1.1 255.255.255.0
IP nat inside
IP virtual-reassembly
IP tcp adjust-mss 1412
automatic duplex
automatic speed
!
interface FastEthernet0/0/0
no ip address
Shutdown
automatic duplex
automatic speed
!
type of interface virtual-Template44 tunnel
IP unnumbered GigabitEthernet0/0
ipv4 ipsec tunnel mode
Tunnel ipsec VPN-PROFILE protection profile
!
interface Dialer0
no ip address
IP mtu 1452
IP virtual-reassembly
Shutdown
!
local pool IP VPN-POOL 192.168.1.150 192.168.1.250
IP forward-Protocol ND
IP http server
IP 8081 http port
23 class IP http access
local IP http authentication
no ip http secure server
IP http timeout policy slowed down 60 life 86400 request 10000
!
!
IP nat inside source list ACL - NAT interface GigabitEthernet0/0 overload
!
IP access-list standard ACL-TELNET
allow a
!
extended ACL - NAT IP access list
ip permit 192.168.1.0 0.0.0.255 any
IP extended ACL-VPN-SPLIT access list
ip permit 192.168.1.0 0.0.0.255 192.168.1.0 0.0.0.255
scope of access to IP-VPN-ACL-SPLIT list
!
control plan
!
exec banner ^ C
% Warning of password expiration.
-----------------------------------------------------------------------
Professional configuration Cisco (Cisco CP) is installed on this device
and it provides the default username "cisco" single use. If you have
already used the username "cisco" to connect to the router and your IOS image
supports the option "unique" user, that user name is already expired.
You will not be able to connect to the router with the username when you leave
This session.
It is strongly recommended that you create a new user name with a privilege level
15 using the following command.
username
secret privilege 15 0 Replace
and with the username and password you want use.
-----------------------------------------------------------------------
Line con 0
exec-timeout 0 0
Synchronous recording
line to 0
line vty 0 4
ACL-TELNET access class in
exec-timeout 30 0
privilege level 15
Synchronous recording
transport input telnet ssh
line vty 5 15
ACL-TELNET access class in
exec-timeout 30 0
privilege level 15
Synchronous recording
transport input telnet ssh
line vty 16 988
ACL-TELNET access class in
exec-timeout 30 0
Synchronous recording
transport input telnet ssh
!
Scheduler allocate 20000 1000
end
CISCO2821 #.
I think that you made a mistake with your ACL name. the ACL applied is "VPN-ACL-SPLIT" which is an empty ACL. You must switch to that of "ACL-VPN-SPLIT" that has the entry "ip 192.168.1.0 allow 0.0.0.255 192.168.1.0 0.0.0.255" inside.
-
Client VPN router IOS, and site to site vpn
Hello
Im trying to configure a vpn client access to an ios router that already has a vpn site-to site running. I don't see how the two can run on the same router.
So I guess my question is is it possible? and if anyone has therefore had a config that they can share or a useful link.
IM using a router 800 series with 12.4 ios
Thank you very much
Colin
ReadersUK wrote:
Hi
Im trying to configure access for a vpn client to a ios router that already has a site to site vpn running. I cant see how both can be running on the same router.
So i guess my question is can this be done? and if so has anyone got a config they can share or a useful link.
im using a 800 series router with 12.4 ios
Many thanks
Colin
Colin
It can be done. Look at this config example that shows a router configured with a site to site VPN and client vpn - connection
Jon
-
Client VPN router 1841 will not establish tunnel
We have a 1841 with IOS 12.4 (3) we have been unable to establish a tunnel to using the 4.8.01.0300 version. It will not exchange keys ISAKMP whatever we use parameters. Debugging is a variety of errors including poorly matched to encryption, authentication, etc. It will not match even the default isakmp policy!
Here are the relevant parts of the config
No aaa new-model
!
resources policy
crypto ISAKMP policy 10
BA aes 256
preshared authentication
Group 2
!
crypto ISAKMP policy 100
md5 hash
preshared authentication
Group 2
!
Configuration group Xclient crypto isakmp client
test key
pool vpnpool
ACL 101
!
Crypto ipsec transform-set esp - aes 256 esp-sha-hmac AES256-SHA
!
Crypto-map dynamic dyn_map 15
game of transformation-AES256-SHA
market arriere-route
!
!
launch of the RA_map client configuration address card crypto
client configuration address card crypto RA_map answer
map RA_map 15-isakmp ipsec crypto dynamic dyn_map
interface FastEthernet0/0
Description "field.
IP x.x.x.x 255.255.255.248
IP access-group 150 to
inspect the IP default100 in
NAT outside IP
IP virtual-reassembly
automatic duplex
automatic speed
card crypto RA_map
And an example on Isakmp debug:
* 21:53:47.903 Jun 28: ISAKMP: (0:0:N / A:0): audit ISAKMP transform 14 against priority policy 100
* 21:53:47.903 Jun 28: ISAKMP: DES-CBC encryption
* 21:53:47.903 Jun 28: ISAKMP: MD5 hash
* 21:53:47.903 Jun 28: ISAKMP: group by default 2
* 21:53:47.903 Jun 28: ISAKMP: pre-shared key auth
* 21:53:47.903 Jun 28: ISAKMP: type of life in seconds
* 21:53:47.903 Jun 28: ISAKMP: life (IPV) 0x0 0 x 20 0xC4 0x9B
* 21:53:47.903 Jun 28: ISAKMP: (0:0:N / A:0): pre-shared authentication offered but does not match policy.
* 21:53:47.903 Jun 28: ISAKMP: (0:0:N / A:0): atts are not acceptable. Next payload is 0
* 21:53:47.903 Jun 28: ISAKMP: (0:0:N / A:0): audit ISAKMP transform 1 against priority policy 65535
We cannot understand why the router will not match the pre-shared authentication setting, or any other parameter (encryption, hash etc.) we change.
We tried to remove the NAT and ACLs nothing helps... What Miss me?
Thanks
There are various debug command? Crypto engine for debugging? Displays information about the cryptographic engine, for example what Cisco IOS software performs encryption or decryption operations. ? Debug crypto ipsec. For more information, see the following URL
http://www.Cisco.com/en/us/products/ps6350/products_configuration_guide_chapter09186a0080455b04.html
-
OfficeJet 6500 and router Wireless does not connect
I just bought an Officejet 6500 and try to connect to my wireless router. Whenever I try to connect the printer to wireless it crashes. The power button does not light, but the screen is lit without text. At this point, I can't close or get it running again. I am running Vista Business 64-bit, and the router is a 2wire 1800 HG through AT & T. It works very well with a usb connection.
Thanks in advance. John
I think you just meet a known issue with some printers of HP network with routers 2WIRE AT & T DSL.
Have identified us the problem and will deploy an update in the future. So far, the work around is to assign a static IP address to the printer. Here's a way to do this:
- Unplug the phone line from the 2WIRE router
- Cut the power to the 2WIRE router, wait 30 seconds, then turn on the power.
- Go through the normal process of the printer connected to the 2WIRE (Ethernet or Wi - Fi) device. The printer will not crash as long as the telephone line is disconnected from the 2WIRE device.
- The Officejet front panel, go to the menu of 'Advanced Setup' under 'network '.
- Select 'Settings of intellectual property', acknowledge receipt of the warning and select "" manual IP ".
- Select "IP address" and change the last group of IPS (byte) to something higher or lower. Specifically to your 2WIRE router, select 192.168.0.60.
- Press Ok and plug the phone line into the 2WIRE router.
-
WRT120N Wireless laptop connected to the router, but does not connect to internet
I have a HughesNet HN9000 modem connected to a Linksys WRT120N router. I have two desktop computers, both running XP Home, connected to the router via ethernet .5e cables and work perfectly. I have a laptop running Vista Home Premium, I am trying to connect to the internet via the internal wireless card. According to me, the laptop connects with the wireless router, as it connects but says 'Local only' - it won't let me access the router IP/control panel. I tried to reset the router / modem as well as the parameters of the laptop, but I keep getting the same question.
If I connect the laptop and the port #3 on the router via a cable .5e I can browse the Internet. But I need to be able to use the laptop throughout the House so electrician is not an option.
I found this article which directed me to this download , which worked. If your help is most needed. Thanks anyway.
-
I recently had need save money and cut off my cable service. Fortunately my building has a service that they lead in all apartments. It's just an ethernet wire that runs into my apt... (I pay for it with my mainentance). The router linksys has worked with the cable modem, but as soon as I plug the service buildings (i.e. Fios) it doesn't let me go on the internet. If I hang the service buildings until dirrectly on my Vista PC or Mac OS 10, it works fine but as soon as I set up the router I get an unable to connect to the internet message on Firefox, IE and Safari. Ive updated the ware closes on it and Ive reset router noumerous times. IM at a loss. Would appreciate any help.
Probably, you will need to reconfigure your modem. Here is the procedure.
-
I have a Toshiba laptop 64 bit running Windows 10 Home, 8 GB, 1 t hard drive.
Router is a Samsung phone using Android because it was the only router that I could find which would take the wireless signal.
I live very pastoral, no neighbours for miles, so I never saw the need for a password on my router.
Now, some people are installs in less than 400 feet from me, and I think they're piggybacking on my Wifi because my access speed has slowed considerably since they moved in.
So I decided to change the password of the router, unfortunately, I can not put in any password I want. It gives me the opportunity to have a predefined password. So I changed the name of the router I could do without problem.
My computer very quickly without any problem, however, my printer which worked great for a year with the old router name does not connect on the new name of the router.
Here is what I tried:
I had hoped he would ask me for a new name / password, but it did not.
Then I plugged a cable between the printer and the laptop in the hopes that it would produce a different kind of results. It has not changed anything. There is no screen menu on what that be like this on the printer.
I pressed the wireless button that has the flashing blue light and nothing happened.
I pressed the button, don't know what it is, but it has a white light, and nothing happened.
I went on the HP site and followed the instructions but he just said do not connect the cable until told to do so. So I disconnected everything, lights out and turned back on and still no connection and no invite to plug whatever it is.
Y at - it everywhere where I have being a novice could get instructions on how to get this working?
I appreciate any help you can give me. Thank you.
Hello
I think you are talking about SSID. Please, think of it as a new router and use the following ways to correct:
http://www.HP.com/global/au/en/wireless/reconfiguring-system-Help3.html
Kind regards. -
I have tried everything recently adjust the settings of the firewall from my window and a box appears saying that after an unidentified error, I can't access my firewall. After some research, I discovered that it was because my client group policy server does not connect and a small box appears saying that whenever I connect to my laptop. It is not effect my use of the internet at all, so I've never bothered to see what that meant until now I need to access my firewall. I tried to adjust the settings in group policy, but everything is gray and I can't change anything. I use an admin account so I don't know why I can't set the parameters. I'm completely stuck and I don't know that much about computers. Is there anything else I can try? I also tried a system restore, but it lasts for a long time and I can return only 5 days. Thank you
Hi Sheldon,
Are you connected or connected to a work network or domain? If so, this could be a policy governed by your network administrator, and you will not be able to change it.You might try to tell scientists on TechNet on your question to see if they have a better answer for you: -
VPN does not connect in some places
I have a laptop running v5 Cisco VPN Client that connects to the office of some places network fine, but not other places. and in the places where it does not connect, it connects fine to another unrelated network. by "does not connect", I mean that I can't access any of the resources on the office network - the client software seems to work, but there is no access, I cannot ping anything on the office network. What would cause this? Here is the log file from a location where it does not connect to the office network:
Cisco Systems VPN Client 5.0.07.0290 Version
Copyright (C) 1998-2010 Cisco Systems, Inc.. All rights reserved.
Customer type: Windows, Windows NT
Running: 6.1.7600
Directory of config files: E:\Cisco systems VPN Client\1 21:36:30.625 07/03/11 Sev = WARNING/2 CVPND/0xE3400013
AddRoute cannot add a route which the metric is 0: code 160
Destination 5.0.0.0
Subnet mask 255.0.0.0
Gateway 192.36.253.1
Interface 192.36.253.1792 21:36:30.625 07/03/11 Sev = WARNING/2 CM/0xA3100024
Failed to add the route. Network: 5000000, subnet mask: ff000000, Interface: c024fdb3 Gateway: c024fd01.in this particular case, the local network uses the range of 192.168.1.x IP addresses, so that shouldn't be a problem.
Lee
Could you go through a PAT instrument, so you are not able to access resources after the VPN is connected because ESP packets usually will not go through a PAT tool.
What must be configured on the VPN server is to allow NAT - t (NAT Traversal), IE: encapsulation of the ESP package in UDP or TCP packet, then it passes through PAT instrument very well.
What server VPN should you terminate the VPN Client?
The command to activate on the SAA would be: crypto isakmp nat-traversal 20
Let me know if you have other devices like the VPN server.
Hope that helps.
-
Bluetooth does not connect on iOS 10 and sierra OS
I just bought an iphone 7, Apple Watch 2 and I updated my computer to sierra yesterday.
I wanted to do the auto unlock with my watch, but my phone does not connect to the Mac with bluetooth. He wants to connect and the phone is displayed in the bluetooth settings, it says on my phone to pair if the numbers are the same, and then he "fails to connect. so im lost and I can't use my watch.
I have reset my watch (by unpairing), iphone (by resetting all settings) and rebooted my computer.
It seems that the "it just works era" is over for apple.
If misery loves company, I'm here! Just posted my new iphone 7 + setting BLUETOOTH is not 'discover' one of my devices (in 2015 Lexus and Bose radio/speakers). In addition my iPad and iPad air are also not 'discover' devices! I think that this happened once I installed the latest ios 10.0.2 software on all my devices. Please reply if you receive some 'advice' from someone in the "know"! Thank you!
-
15 - r074TU: laptop does not connect to the router
Day sum... .my laptop (model No. 15r074TU) with window 8.1 does not connect to the router that is D-link
I uninstalled my driver reinstalled again, but it didn't work... even if I formatted my laptop, reconfigure the router and... done with all possible measures to overcome this problem, but have ultimately failed. Please suggest ways to tackle this problem as soon as possible...
Follow the wizards in the following forum sticky and troubleshooting.
Maybe you are looking for
-
Current have a 480 GB SSD and a 2 TB HDD installed on our end 2009 27 "iMac. What I want to do is to use the 2 TB as start player for my wife so that all its data (about 300 GB) is stored and to use the SSD 480 GB to store my data. Question 1: Is it
-
16.0.1 redirect unwanted https forces
One of my friends and I worked more than a year on a web site project. We now see that Firefox automatically redirects the URL to an address https with a 404 not found error. If you type in http://www.sitename.com, www.sitename.com or sitename.com an
-
Keyboard and HP Split 2 x touch screen stop working
Good evening My touch screen worked fine a second, stop working the next day. Just the keyboard worked, so I rebooted and updated and when we turn back, the touchscreen still does not work. I stopped him once again, when he came back on, or the touch
-
Download Windows mail issue hot photo
I use windows live hotmail to send photos. I can only pictures to download 3 then a message appears "message from the web page" invalid cast exception. How can I fix this? No problem before the problem had begun.
-
BlackBerry Smartphones Email problem
Hello I had some problems with the reception of e-mails and I uninstalled the context menu. When I tried to reinstall is no longer accept the user name and password on the grounds that they are "invalid." Noted that the user can access e-mail and pas