Guests who will remain not connected to vCenter

Similar Questions

• WRT54G v.5 will remain not connected to the new laptop / Windows 7 Premium

  WRT54G v.5 will remain not connected to the new laptop / Windows 7 Premium. It works continuously with a cycle detection, connection, loss of connection; detection, connection, loss of connection, etc... The router works through this cycle, basically acting as if I disconnected and then reconnected to the power to reset, it disrupts my Internet connection to my Wired iMac and wireless, another office to the floor. Paid for Linksys support today and through remote access, he put up a new network on my desktop (iMac). After finishing, the problem still exists. When I told him that the problem had not been corrected, he said just wait an hour or two and it should work itself. She, of course, did not himself. Any ideas out there?

  Nevermind - I seem to have solved the problem with a simple firmware. Funny how the Linksys technician support don't think to ask what version of the router I have or suggest that I should try to upgrade firmware first. However, he is quite good at trying to upsell me for a new router instead of trying to help me solve the problem I had. It makes me want to go buy Netgear next time, thanks a lot!

• I have an inspiron which will remain not connected to wireless internet but another computer works perfectly

  I have a Dell inspiration that will remain not connected to the internet wireless, but the other computer

  Are the two computers to the same distance from the router?   How many bars do you plan to connect?  You use without wireless - G or wireless-N?  Try clicking on the bars (next to the lower-right clck) then click on Open network and sharing Center, then click on wireless network connection and see that the number of MB/s is just above the bars in the middle of the right.  You should see something like 54 Mbps and at least 2 or 3 bars.

  Good luck.

• Windows Live will remain not connected

  Original title: won't remember

  My account will remain not connected, whenever I go to my email that I resign, even when I check the box to keep me signed.

  Hello

  -What browser are you using to access Windows live?

  -If you use Internet Explorer, then what is the version?

  I suggest you try the following steps if you are using Internet Explorer.

  1. open Internet Explorer, click the Start button. In the search box, and then type Internet Explorerin the list of results, click on Internet Explorer.

  2. press the ALT key then press click on Tools and then click Internet Options.

  3. click on the content tab.

  4. under AutoComplete, and then click settings.

  5 Select or clear checkboxes address bar, Forms, usernames and passwords on formsand ask me before saving passwords .

  6. click OKand then click OK again.

  For more information, visit the below mentioned link:

  http://Windows.Microsoft.com/en-us/Windows7/fill-in-website-forms-and-passwords-automatically

  If the problem persists, I suggest you to ask your question in the windows live forum

  http://windowslivehelp.com/

  Let us know if it helps.

• Windows XP card reader will remain not connected

  We use a software called easy dental and occasionally when we try to open it gives an error message saying that it can not connect to the database... After talking with our easy dental support team, they have advised that call us microsoft Windows XP and tell them that "our card reader does not remain", these are the details I only... they thought that Microsoft would be able to walk us through the process for solve the problem

  By design, a mapped network drive disconnects after a period of inactivity.  We should return quickly when necessary.  For more information:

  "Drive mapped to the network connection may be lost.
    <>http://support.Microsoft.com/kb/297684 >

  HTH,
  JW

• WIFI will remain not connected

  Buy HP Pavilion x 360.  Whenever I use my laptop I reconnect the WIFI via Network Diagnostics.  How can I keep my WIFI connected?  I don't know if mst be a setting somewhere.

  Hi tkveene,

  I'd love to help you, but it is necessary to get more details to help you properly. It would be useful to have the right product Pavilion number X 360 is a series with many variations. Please read the following document if you need help to find out who.

  How can I find my model number or product number?

  The following pages are useful for troubleshooting wireless connectivity problems.

  Troubleshooting wireless network and Internet (Windows 8)

  Universal solution WLAN, Wireless and Wi - Fi errors

  In addition, you can watch the the power management of your wireless adapter:
  Turn off the power to the adapter:
  1. open Device Manager. (Win Key + R > type devmgmt.msc > OK)
  2. expand the network adapters.
  3. right click on the Ethernet adapter / wireless, and then click Properties.
  4. click on the power management tab.
  5 remove the check mark next to allow the computer to turn off this device to save power.
  6. click on OK.
  7 test cycle.

  Also if you need to forget a network on your laptop, then you can try the following:

  How can we forget the wireless networking in Win 8, when it is in the range

  Go to settings in the menu of charms
  Windows key + i
  Click on the wireless icon
  Right-click on the network you want to forget
  Choose forget this network

  If the network is not in range that the procedure above does not work, use the following:
  Press the Windows key + x and press c to open a command prompt

  Then at the command prompt, type the following command to view a list of all networks wireless currently known on your computer.

  netsh wlan show profiles

  From the displayed list generated by this command, note the network name that you want to delete, and type the following command. The network name must be inside the quotes.

  netsh wlan delete profile name = "name of wireless network to forget."

  Please let me know if you need additional assistance. I hope it's useful for you.

  Kind regards

• case # 1178354456. Complete Windows is no longer install new programs. IE will remain not connected

  Windows Installer does not work.  programs (program of the printer) will not be installed.  That is to say wii not stay connected.  This uprade last saince for windows vista

  Hello JoeB66,

  You receive error messages when you try to install programs?

  Have you tried to install in compatibility mode printing software?

  http://Windows.Microsoft.com/en-us/Windows7/what-is-program-compatibility?SignedIn=1

  For your internet connection problems, I recommend you to look at this article and try the troubleshooting is:

  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-network-connection-problems

• When I download it will remain not connected?

  When I try to download every thing to "freewebs.com" he used uploaded to it, it keeps saying connect to the server, but will never connect. What I am doing wrong?
  

  Promblem fixed I had to just make a new site because it is not properly configured.

• iPhone 6 will remain not connected

  Recently my iPhone 6 will not be plugged. Even sitting on a night the lightning cable comes out and then my phone won't load. Anyone know of a solution for this? Is this a common problem?

  Raymond Swanson wrote:

  Recently my iPhone 6 will not be plugged. Even sitting on a night the lightning cable comes out and then my phone won't load. Anyone know of a solution for this? Is this a common problem?

  No, this is not common. Have you looked into the charge socket? It seems that it is a certain type of lint, dirt and debris that is blocking you plug the cable of lightning completely. Check these things and you can try to remove anything with a small wooden toothpick or toothbrush soft and dry. You can blow with canned air. Make sure that the device is turned off before doing so. If this is not enough, then make an appointment at the Genius Bar to the nearest Apple Store of the device studied by Apple for any other question.

• RALink RT5390 802.11b/g/n WiFi Adapter will remain not connected

  I use a laptop of Hp 2000, and the adapter installed on the computer provided wireless is a Ralink RT5390 802.11b/g/n WiFi Adapter.  I ran the driver update tool, and it says I have install the driver update.  I have also run the tool to "Diagnose the problem", and he says that he has no problem.  However, the computer loses internet connection constantly.  I guess it has something to do with the wireless adapter, because all other wireless in the House have no problems. The operating system is Windows 7.  I'm a little tech savvy and can normally include questions to just play with it for a while, but this one has me dumb founded, and its very annoying when you try to do something and you just loose connection and have to start all over again. Help, please!

  Hello:

  I found that the relying on a tool the driver does not always provide information.

  Here is the link to the latest version of the driver if you don't v.3.2.12.0 (13 April 2012) installed.

  http://h20000.www2.HP.com/bizsupport/TechSupport/SoftwareDescription.jsp?lang=en & CC = US & prodTypeId = 321957 & prodSeriesId = 3688868 & swItem = ob-104619-1 & mode = 3

  Paul

• Can not connect to vcenter after reboot

  Hello VMware,

  I can not connect to vcenter after reboot with the error «Failed to connect to the Vmware research service»

  

  I tried to follow below doc but no help.

  http://www.myvmwareblog.com/2012/11/28/lookupservicesdk-SSL-certificate-verification-failed/

  I tried to play with the Vcenter screen underneath, but no luck.

  
  

  To resolve this problem, replace the VCSA IP with hostname VCSA in the search service configuration file, ls_url.txt file.

  To replace the VCSA IP address with the host VCSA name in the ls_url.txt file:

  1. Connect to the VCSA via ssh under the root user
  2. Go to the directory/etc/vmware-sso using the command:

     CD/etc/vmware-sso

  3. Make a backup copy of the file ls_url.txt using the command:

     CP ls_url.txt ls_url.txt.bak

  4. Open the file ls_url.txt using a text editor
  5. Replace the VCSA IP address with the host name of the VCSA. For example:

     https:// Lookupservice/XXXXXXXXXX/sdk

     Where XXXXXX is the host name of the VCSA.

     Note: It is usually the host name of the domain the VCSA FULL name. Make sure it matches the common name (CN) in the certificate name.

  6. Restart the VCSA services by running the command:

     restart the /etc/init.d/VMware-vpxd
     restart the /etc/init.d/VMware-SSO
     restart the /etc/init.d/VMware-InventoryService

     Or

     Restart the VCSA.

  Alternatively, you can use this workaround to regenerate the certificates for the vCenter Server Appliance.To to regenerate the certificates for the vCenter Server Appliance:

  1. Temporarily change the IP address of the vCenter Server Appliance to a different IP address, not used
  2. Restart the vCenter Server Appliance
  3. Change the IP address of the vCenter Server Appliance to the originating IP address
  4. Restart the vCenter Server Appliance
  5. Connect to vCenter Server Appliance, https://vcenterserveripmanagement Web page: 5480
  6. Click the Administration tab, and then select Yes to certificate enabled regeneration
  7. Click send to save the changes
  8. Restart the vCenter Server Appliance

• Updated the operating system on the server for Windows 2012. Now I can not connect to vcenter.

  Updated the operating system on the server for Windows 2012. Now I can not connect to vcenter.

  What version of vCenter Server do you run? Only of vCenter Server 5.0 Update 2 is currently supported on Windows 2012.

  André

• Can not connect to vCenter

  Simply, we discover that we can not connect to log in the vCenter uses the vSphere client.  That's what we get:

  Call 'ServiceDirectory.QueryServiceEndpointList' of object "ServiceDirectory" on vCenter Server '10.x.x.x' failed.

  I tried to look it up, but can't find a lot of resources.  I found this, but do not know where he is. We have a limited access since the main guy is out.

  http://arritdor.e-Wilkin.com/2012/02/error-call-servicedirectoryqueryservice.html

  Thank you

  Tntrac

  The option is in your VM vCenter. you will need to connect to this computer and disable the Routing and remote access.

  

  You must run services.msc and disable the service.

  And also reboot the server vcenter service in the same place. If you do not have access to the vCenter VM Windows, you will need to locate the host that has the vcenter VM and then login in there and do it.

• BDE 2.1.1 Fling Management server does not connect to vCenter

  I have the management server deployed in the environment, the plugin installed successfully and vCenter is connected to the administration via the Web interface of vCenter server. This problem occurs when I go to a data store or add it to a network.

  I get the following (via the GUI or CLI):

  Version: 2.1.1

  Welcome to Serengeti CLI

  Serengeti > Connect - host hadoop - mgmt.or1.omniture.com:8443

  Enter the user name: [email protected]

  Enter password: *.

  Connected

  Serengeti > data store, add - name defaultDS - spec DS10HadoopOR1 - shared type

  datastore defaultDS add failed: unable to connect to vCenter Server.

  The error in the serengeti.log file is a generic JAVA error. The vCenter is 5.5U2 and ESXi hosts are 5.5U1.

  --

  Chris.

  Thanks Charlie for a helping hand.

  I found some info in the serengeti.log and the serengeti - boot.log Chris post:

  Serengeti - boot.log:

  I, [2015-02 - 12 T 20: 56:27.722910 #3336] INFO -: templateVmName: vSphere Big Data Extensions - Node Template

  Serengeti.log:

  Caused by: com.vmware.bdd.utils.AuAssert: FAILURE

  at com.vmware.bdd.utils.AuAssert.FAILURE(AuAssert.java:28)

  at com.vmware.bdd.utils.AuAssert.check(AuAssert.java:43)

  at com.vmware.bdd.utils.AuAssert.check(AuAssert.java:50)

  at com.vmware.bdd.service.impl.ClusteringService.getTemplateVm(ClusteringService.java:408)

  [2015 02-12 T 14: 46:47.438 - 0700] INFO Event_Expander | com.vmware.bdd.service.event.EventScheduler: to develop events: [{me = null: VirtualMachine:vm - 136, event = VmResourcePoolMoved}]

  [2015 02-12 T 14: 46:47.626 - 0700] INFO pool-2-wire-4 | com.vmware.bdd.service.utils.VcResourceUtils: folder xxx-uuid was not found.

  [2015 02-12 T 14: 46:47.627 - 0700] INFO pool-2-wire-4 | com.vmware.bdd.service.event.VmEventManager: VM root folderxxx-uuid is not yet created. Ignore the event outside of VM.

  [2015 02-12 T 14: 46:58.393 - 0700] Event_Handler INFO | com.vmware.bdd.service.event.EventScheduler: processed 2 new events

  [2015 02-12 T 14: 46:58.394 - 0700] Event_Handler INFO | com.vmware.bdd.service.event.EventScheduler: processed events: [{me = null: VirtualMachine:vm - 137, event = VmResourcePoolMoved}, {me = null: VirtualMachine:vm - 136, event = VmResourcePoolMoved}]

  [2015 02-12 T 14: 47:13.183 - 0700] Http-8443-5 ERROR | com.vmware.bdd.rest.RestResource: rest call error

  com.vmware.bdd.exception.BddException: unable to connect to vCenter Server.

  at com.vmware.bdd.exception.BddException.INIT_VC_FAIL(BddException.java:189)

  at com.vmware.bdd.rest.RestResource.verifyInitialized(RestResource.java:1175)

  at com.vmware.bdd.rest.RestResource.addDatastore(RestResource.java:636)

  This log shows THAT BDE Server cannot find the node named "vSphere Big Data Extensions - Node Template" model.  When you deploy the BDE Fling, the management server and hadoop-model VM must be deployed in the same folder in, under a pile of vCenter.  Please check and follow the BDE 2.1.1 Fling deployment guide and deploy again.  BTW, you can customize the name of the server VM and the VM model during their deployment and make sure the correct model name together when you deploy the server VM.

• Client VPN will travel not connected via 877w

  Hello

  I've implemented a Cisco 877w and it works very well for web access

  Client VPN on my laptop connects via the 877w and authenticates on my remote work ASA5510 firewall.

  Problem is after you connect to the ASA, I can not connect anything internally work network (10.0.0.0/24), ping, etc. RDP is back with no answer.

  I've attached the config, can someone tell me what I am missing, might access a list?

  Thanks for your help

  Chris

  This router is made PAT/NAT, Ipsec blocking.

  Activate Nat on the ASA course remote.

  ISAKMP nat - t or crypto isakmp nat - t

  HTH

  Sangaré

  Pls rate helpful messages