Cluster commands cause a loop for hanging or LabVIEW to hang

Similar Questions

• HOW TO CREATE A STOP COMMAND IN LOOP FOR

  I have a problem. I can't put a stop to the VI attached here. I want to stop an iteration without support on cancel execution, because I want to connect this VI by a Subvi to control a motor continuous.

  Thank you

  Hello

  in order to stop your first vi, you can use a stop button for the while loop to 'or' with the release of your "equal" comparison function Then you can also use a local variable created the stop button to stop the loop for, configure it with a conditional expression (right click on the loop for > conditional expression).

  This way if you press "stop"button, you will stop the while loop and the loop together foor.

  Good bye

• Creating a table of automatic indexing of loop for

  Hello and greetings from a newbie to LabView,

  In my program, I want to write several orders via VISA and read them in order. I created a table of command and auto-indexé to a loop for.

  I want to receive a table of responses, in the order they were read of course. However, I'm not sure what is the best way to do it.

  I'm sure that the solution is simple but have been unable to find one. I have attached the vi for reference. (VISA vi reading is part of the LabView unit driver), which works, but looks like a unmodular approach and inelegant.

  Thank you!

  Simple, you can auto-index the output!

  

• VI is jump a loop "For".

  Zipped VI is fixed, the upper level has "7_AD-DC producer consumer" as the title.  You will have to dig into the folder for access.

  I have attached a picture of the Vi, highlighted in red is the loop in question.

  The problem I have is that when I run the vi has the range of 0.25 to 0.5 Volt (chosen in the loop of producer not shown), it works fine, but if I run the vi put on the beach of 1 volt, it ignores all highlight loop, and finishes just the event.

  The program aims to help the particular device calibration.  If you follow the path of the error, it crosses the upper part (1605, 1605 mode range, range of AC - DC, the factor N, etc.) all the way through the indicators for "1 k reference in ' and ' 1 k reference on.  The program runs right up through these measures of reference, but when it is in range Volt 1 (shown in the picture) it ignores the entire for loop.  I son of error in all, and I thought that those who would prevent race conditions and they would oblige the Vi to run as expected, but apparently not.

  It's kinda a Vi spaghetti, I'm not the best with LabView, but it seems so strange to me that it works when the value 1/2 a volt but don't not 1 volt value.  I put the indicators on the elements that fuel the loop For, the number of frequencies and the tables of frequencies look good and I can't really think what causes violence to ignore the loop for.

  The for loop is not in 'jumps' it of executing 0 times and out of default data for all tunnels.

  You have an entrance tunnel auto-indexé why wire terminal N at all? The loop will be the least number of iterations it can.  N times, either the smaller auto-indexd table is something less.

  EVEN worse: the indexed table auto comes from a tunnel exit case structure value "Use default if unwired" so you have two options.  There is a hidden code clear the Board before being sent out of the cases showed, OR the value of the number of frequencies is<>

• Cannot use Select inside the loop For inside the SCTL (FPGA) - Bug? An alternative?

  When I put a Select statement inside a loop in a loop of Timed Cycle in LabVIEW FPGA, I get the following error when I try to compile:

  "An internal software error occurred. Please contact National Instruments technical support on ni.com/support with the following information:

  Error-61003 occurred at

  Possible reasons:

  LabVIEW FPGA: you cannot include this function in a loop For when the loop is within a single cycle timed loop. »

  I didn't know that whatever it is documented that says that this is not allowed; is this a bug or am I missing some documents?

  The code that causes this error looks like this, inside a SCTL (ignore Boolean wire wandering behind the loop for)

  

  I came up with the code below instead, which compiles into one Cycle timed loop, but it is a bit ugly. Does anyone have a better suggestion?

  

  This issue is currently followed under the CAR # 592391. Please keep an eye on our patches and new versions as usual!

• Loops For parallel within a Structure of case - one or more threads?

  I wonder if I put parallel for loops within a structure of business will be to the loops have their own thread, or run in the same thread?

  I think it would be a thread, but then I saw this post when looking on the forums to check.  Alas, I ask directly.

  I created the parallel for loops to improve the performance. (I'm in BT 8.5, if do not have the option of clever parallelization by right-clicking the loop for).   The parallel loops have the same code in each (I know I do the reentrant subVIs).  I wanted to put a case around the loop structure, so that they do not run if there is a mistake in them (I have a master/slave updated structure the where the for loops are slaves) because the code inside the for loops is 1) depends on correct data of the master and 2) by the high-performance computing I want to skip execution of loops if the master has a stop command.  Otherwise, errors are likely to be generated in the slaves because of incorrect data by the captain or the judgment happens quickly, which can confuse the user.

  Let me know if you need more details.  Thank you!

  ~ Kristen

  Each loop will run on its own thread and they will work in parallel. The only downside would be if they call them both the same Subvi and the Subvi is not reentrant. Besides, any shared call which blocks will result in two loops is not able to run completely independently.

• How can I autoindex looping for to create several channels daqmx

  I'm trying to autoindex create a loop FOR containing the DAQmx vi to create AI multi-channel voltage with identical settings, except that I need to apply specific channel names using a constant and specific physical channels using a constant of channel. Wiring of a constant DAQmx of physical channel does not work because the data type is incorrect. Similarly, I don't understand how to use a string constant to autoindex through the channel names is or how to configure the constant string (s) to assign names. Also, when I try to make one of these, I get a tunnel to exit the DAQmx autoindex create channel, rather than a task out. I can achieve my goal using several explicit DAQmx create calls to channel, but for high channel count, it is very time consuming.

  I use LV 8.5.

  I'm hoping to find the code showing how to perform the conversion type, flattening, or what to do.

  Diane has.

  I have an array of clusters.  Each element of this array is a cluster.  The cluster consists of a (scalar) string and input/output (also scalar).

  In addition, my TI attachment extracted.  I think that your file has been LV2009.  If so, you can drag the image from the browser and drop it onto a diagram.

• The application has failed to start because its side-by-side configuration is incorrect. See the application event log or use the command-line sxstrace.exe for more details

  Hello

  I can t open Google Earth or Microsoft Office programs because I get this message - the application could not start because its side-by-side configuration is incorrect. Please see the application event log or use the command-line sxstrace.exe for more details.

  A few days ago I could open all what programs. I put t know what is the problem.

  I did sxstrace and that's what I have-

  =================
  Launch the activation context generation.
  Input parameter:
  Flags = 0
  ProcessorArchitecture = Wow32
  CultureFallBacks = en-US; en
  ManifestPath = C:\Program Files (x 86) \Google\Google Earth\client\googleearth.exe
  AssemblyDirectory = C:\Program Files (x 86) \Google\Google Earth\client\
  Application configuration file =
  -----------------
  INFO: File analysis shows C:\Program Files (x 86) \Google\Google Earth\client\googleearth.exe.
  INFO: Manifest definition identity is (null).
  INFO: Reference: Microsoft.VC80.CRT, processorArchitecture = "x 86" publicKeyToken = "1fc8b3b9a1e18e3b", type = "win32", version = "8.0.50727.4053"
  INFO: Resolving reference Microsoft.VC80.CRT, processorArchitecture = "x 86" publicKeyToken = "1fc8b3b9a1e18e3b", type = "win32", version = "8.0.50727.4053".
  INFO: Resolving reference for ProcessorArchitecture WOW64.
  INFO: Resolving reference for the neutral culture.
  INFO: Application binding policy.
  INFO: No found publisher policy.
  INFO: No redirect political connection is found.
  INFO: Start the detection of assembly.
  INFO: Can't find the assembly in WinSxS.
  NEWS: Try to detect manifest to C:\Windows\assembly\GAC_32\Microsoft.VC80.CRT\8.0.50727.4053__1fc8b3b9a1e18e3b\Microsoft.VC80.CRT.DLL.
  INFO: Found no manifesto for the neutral culture.
  INFO: End detection of assembly.
  INFO: Resolving reference for ProcessorArchitecture x 86.
  INFO: Resolving reference for the neutral culture.
  INFO: Application binding policy.
  NEWS: Control strategy of the Publisher C:\Windows\WinSxS\manifests\x86_policy.8.0.microsoft.vc80.crt_1fc8b3b9a1e18e3b_8.0.50727.5592_none_517247830f45081d.manifest
  INFO: Start the detection of assembly.
  INFO: End detection of assembly.
  ERROR: Activation context generation failed.
  End activation context generation.

  Help, please!

  This type of error can be caused if the Visual C++ library runtime components are missing or because of a third-party software.

  Follow the steps below:
   
  Method 1:
  If the problem is caused by the lack of Visual C++ libraries, you can download and install the Runtime components of Visual C++ libraries from the link below:
   
  This error can occur when the Microsoft .NET Framework installation on the computer is damaged or is missing.

  Try it out below step to reinstall and repair installation of Microsoft .NET Framework on the computer, then check if you can install the software.

  (a) click the Start button, select Control Panel, click programs and then click on 'Turn Windows has or not.' If you are prompted for an administrator password or a confirmation, type the password or provide confirmation.

  (b) search for Microsoft .NET framework 3.5.1 uncheck, click OK and restart the computer.

  (c) after the reboot, open again "Turn Windows features on or off" and place a check next to Microsoft .NET framework 3.5.1 and restart the computer.

  Step 2

  If the previous step fails, then I suggest that you manually download and install Microsoft Visual C++ 2005 and 2008 Redistributable Package and check to see if you can install the software.

  In programs and features, you do not show that you have installed Microsoft Visual C++ 2005 Redistributable and Microsoft Visual C++ 2008 Redistributable? If this is not the case, download the links here.
   
  Package redistributable Visual C++ 2005 (X 86)
   http://www.Microsoft.com/downloads/en/details.aspx?FamilyId=32BC1BEE-A3F9-4C13-9C99-220B62A191EE&displaylang=en
   
  Visual C++ 2005 (x 64) redistributable package manager
   http://www.Microsoft.com/downloads/en/details.aspx?FamilyId=eb4ebe2d-33c0-4A47-9dd4-b9a6d7bd44da&displaylang=en

  Package redistributable Microsoft Visual C++ 2008 (x 86)

  http://www.Microsoft.com/downloads/en/details.aspx?FamilyId=9B2DA534-3E03-4391-8A4D-074B9F2BC1BF&displaylang=en

  Package redistributable Visual C++ 2008 SP1 (x 64)
   http://www.Microsoft.com/downloads/en/details.aspx?FamilyId=BA9257CA-337F-4B40-8C14-157CFDFFEE4E&displaylang=en

  I hope this helps.

• "Error: the application failed to start because the side by side configuration is incorrect, please see the application event log or use the command-line sxstrace.exe for more details.

  I have QQ (an international chat program) installed on the laptop. Then my hard drive crashed. Now when I try to reinstall it on my new hard drive I get the following message:

  "Error: the application failed to start because the side by side configuration is incorrect, please see the application event log or use the command-line sxstrace.exe for details" -how can I solve this problem? I have Windows 7.

  Hello

  Thanks for choosing Microsoft Community to post your question.

  It seems that you can not install application QQ, you get an error: "the application could not start because the side by side configuration is incorrect, please see the application event log or use the command-line sxstrace.exe for more details.

  We're here to help and guide you in the right direction. This problem could be caused when the computer is missing the correct C++ run time for your type of system components. (x 86 or x 64).

  Here are a few troubleshooting steps that you can try to solve this problem.

  Method 1: we will install Microsoft Visual C++ for your computer package.

  Note: If you use the 32-bit operating system, download and install 32-bit edition(X86).

  If you use the 64-bit operating system, download and install edition(X64) 64-bit.

  Microsoft Visual C++ 2008 SP1 Redistributable Package (x 86)
  http://www.Microsoft.com/downloads/en/details.aspx?FamilyId=A5C84275-3B97-4AB7-A40D-3802B2AF5FC2&displaylang=en

  Microsoft Visual C++ 2008 SP1 Redistributable Package (x 64)
   http://www.Microsoft.com/downloads/en/details.aspx?FamilyId=BA9257CA-337F-4B40-8C14-157CFDFFEE4E&displaylang=en

  Package redistributable Microsoft Visual C++ 2010 (x 86)

  http://www.Microsoft.com/downloads/en/details.aspx?FamilyId=a7b7a05e-6de6-4D3A-A423-37bf0912db84

  Package redistributable Microsoft Visual C++ 2010 (x 64)

  http://www.Microsoft.com/downloads/en/details.aspx?FamilyId=bd512d9e-43c8-4655-81bf-9350143d5867

  Method 2: Run the fixit available at the following link.

  Solve problems with programs that cannot be installed or uninstalled

  http://support.Microsoft.com/mats/Program_Install_and_Uninstall

  Also, check the event log using Event Viewer.

  Please see the link below for more information on how to use Event Viewer to check the error message or information,

  http://Windows.Microsoft.com/en-us/Windows7/what-information-appears-in-event-logs-Event-Viewer

  If you have additional problems, please reply to this post and we will be happy to help you further.

• Ajouter.1 with a loop for?

  I tried to add du.1 increment a value using a loop for, but the for loop has not added to the value of the specific increments.

  So instead of se.1,.2,.3,.4, etc., I got the following when I traced it the loop:

  0

  0.1

  0.2

  0.30000000000000004

  0.4

  0.5

  0.6

  0.7

  0.7999999999999999

  0.8999999999999999

  0.9999999999999999

  This throws my code completely because it causes the loop to execute unnecessary once and the returned value causes other functions are not working well. Please advise on how to solve this problem.  I note that this is not a problem once you get a.25.

  use .toFixed (1); After the value

• Interface user-generated loop for?

  var compLayerArray = new Array("Compsition 1", "Composition 2", "Composition 3");
  var layerControls = newArray();
  
  
  function generateWindow(){
  var layerPositionsWindow = new Window("palette", "Layer Positions", undefined);
  var layerPositionsGroup = layerPositionsWindow.add("panel", undefined, "layerPositionsGroup");
  layerPositionsGroup.orientation = "column";
  
  for(var p = 0; p < compLayerArray.length; p++){
          layerPositionsGroup.add("statictext", undefined, (p+1) + ". " + " " + compLayerArray[p].name);
          layerControls.push(groupOne.add("edittext", undefined, "0"));
  }
  
  var layerPositionsButtonGroup = layerPositionsWindow.add("group", undefined, "layerPositionsButtonGroup");
  layerPositionsButtonGroup.orientation = "row";
  var positionCancel = layerPositionsButtonGroup.add("button", undefined, "Cancel");
  var positionSave = layerPositionsButtonGroup.add("button", undefined, "Save");
  
  layerPositionsWindow.show();
  
  

  I was wondering if it is possible, and if so, how, for generating a user interface based on a loop for? I try to view each layer within a model in the user interface. I can do, because a static text does not require any kind of var. However, when I get to the line 11, I don't really know how I would go about adding a text edit under the name of each layer. I want store a value for each layer. Thank you!

  -Nate

  OK, I see what is happening. You have decided to add an additional group to the user interface within the same main layerPositionGroup. What happens in the loop to the #14 line. Actually, this has changed now the user interface model that was easy to read before to something more complicated to read. So since you have now "group #" then "GroupTwo #" you now generate a user interface with this model...

  Group 1 (statictext)

  GroupTwo 1 (statictext, edittext)

  Group 2 (statictext)

  GroupTwo 2 (statictext, edittext)

  Group 3 (statictext)

  GroupTwo 3 (statictext, edittext)

  .. compare to the original provision of...

  GroupTwo 1 (statictext, edittext)

  GroupTwo 2 (statictext, edittext)

  GroupTwo 3 (statictext, edittext)

  So when you browse the children in the group in the debug.onClick in the #34 line, you do not get anything because 'Group 1 (statictext)' doesn't have a second child, just one, the statictext. This interrupts the process. Not sure why it isn't throwing the error, but it is the cause of your problem.

  Group 1 (statictext) //Has 1 child

  GroupTwo 1 (statictext, edittext) //Has 2 children

  Group 2 (statictext) //Has 1 child

  GroupTwo 2 (statictext, edittext) //Has 2 children

  Group 3 (statictext) //Has 1 child

  Children //Has 2 GroupTwo 3 (statictext, edittext)

  Through this model is very different, because now, you must take account that you want to only read that the odd numbered children clues, those two children. So your onClick for loop must now include a check for odd numbers like that...

  debug.onClick = function(){
       var kids = globalVar.children;
       var kidLen = kids.length;
       var kidValues = new Array();
       for(var k=0; k		   

• How will I know if new loops for 10.1.1 has uploaded?

  So I downloaded the new update, but I can't say the old the new loops loops.  Download it and install it or I have to click on the option 'Download the sounds available' in the menu?

  OR

  Can someone give me the name of loop for one of the loops again so I can search my library of loop?  Thank you!

  It is no new loops have been installed for me, but they may have been installed earlier by the logic. Maybe the update adds iOS GarageBand loops, take a look at this list.

  How to get iOS GB loops in GarageBand for Mac.

• New loops for 10.1.1 even as new loops of logic?

  I have all the additional content for Logic Pro and with the exception of the fabric of Alchemy, are the new Apple Loops for Garageband 10.1.1 identical to what I already under Logic Pro?

  GarageBand gives me the option to download the entire library, which I don't want I don't have to.

  I suspect these new loops for GarageBand 10.1.1 are already in my folders of loops when I updated Logic Pro a few months ago?

  Thank you

  Robert

  

  T

  The App Store shows the update like this:

  

  2600 new Apple Loops and sounds.

  I also installed Logic Pro X.

  There is no new loops installed after 10.11.1 GarageBand update.   The last loop in Library/Audio/Apple Loops is 80 return Beat.caf frommay 2015

  

  GarageBand must have installed something, because the absence of plug-ins error messages are gone, when I open iOS projects GarageBand, but I can't find any new items in the folder/library.

  I'm now trying to download all the available sounds. We'll see what happens.

• If I use a single individual loop for my video and upload it to youtube will be my video will be blocked or will I get copy right strike?

  If I use a single individual loop for my video and upload it to youtube will be my video will be blocked or will I get copy right strike?

  I already read the agreements loops but unable to understand exactly what it means please help me...

  They say individual loops must not be commercialy or other wise distributed...

  That means individual loop should not be used?

  Is the only thing you can NOT do: "Yes, I did these loops and now I'm selling you these loops, claiming that I just them.»

  So they are free, but you are not allowed to sell unaltered loops claiming that make them you. So you can use them for any kind of music, published published, obscure, commercial, anything; without additional costs or restrictions.

  Hello... Please help me I want to just use a single loop of logic pro X for my video and want to download YouTube wil...

• Clear out in a loop for

  Hi guys,.

  I have a problem, so I activate timed values on the outputs analog of my RedLab card.

  The problem is that when I stop the program, the outputs are always activate.

  How can I solve this problem?

  Best regards from max

  What version of LabVIEW?

  I forgot which version he presented, but lately, you can add a CONDITIONAL TERMINAL to a loop FOR.

  Use it to stop the loop if the user clicks a button or if the voltage exceeds 3.14159 Volts, or whatever.

  You can also use a basic while loop, set the AUTOMATIC indexing entries and compare yourself 'i' to N - 1, in the loop.

  Stop BUTTON so STOP = TRUE or i = 3.14159 > N-1 or V...