Codec c60 sending two cameras at the Conference

Similar Questions

• Question about running from two cameras at the same time with MAX

  Hello

  I have two cameras attached to NI PCIe-1430 frame grabber card (Atmel Aviiva M2 CL and Fairchild 2 K LS) IRLS. It's ok when I run two cameras individually, but I can't run them at the same time.

  This is the step that simultaneously run two device:

  1. open MAX, select the port and start image acquisition by pressing the 'Grab' button, I can see the image at this point.

  2. open another MAX session, select the other port and press "enter". I got following error:

  "Error 0xBFF60021".

  Unable to perform request; acquisition in progress'

  Sometimes, I got this error too:

  "Error 0xBFF60022".

  A timeout error occurred while you wait for the specified event. If you expect a picture, check the video data is acquired in the period. If in the meantime the signal, check that the assertion of signal has occurred within the period. »

  I already give enough timeout Fame to the tab settings of Acquisition.

  The MAX version used is 4.5.

  You have an idea on that? Makes simultaneous Imaging MAX support?

  Thank you

  -polarfox

  Thanks for the quick response Bruce.

• MAX cannot find two usb cameras at the same time

  Hello

  I want to use two cameras usb (Thorlabs DCC 1545 M) in NOR-IMAQdx in Labview, but it cannot find a single camera (the one plugged earlier), and also a single camera is shown in MAX. Both cameras working in the manufacturer's software, and if I unplug the 1 unit, the 2nd will be displayed in MAX after a refresh.

  I found that one camera is supported for each USB hub in Labview, and all USB ports in this computer correspond to a same hub online. I don't know if this is causing the problem.

  In fact, I need to take the picture in both cameras at the same time, a switch programmed between the two cameras will work for me.

  Any suggestion and comment will be appreciated.

  Hello Hosni,

  According to this link, you can acquire from multiple USB cameras simultaneously.  The limitation is on the manufacturer and how they interface with the bus of DirectShow.  When you use two cameras of the same make and model, it sometimes happens that not enough information is not IMAQdx to distinguish between the two cameras.  When you switch to MAX cameras, they come as different cameras, or they appear actually virtually the same?

  Since you said switching between them might work, I found an example that does just that.  Just make sure you give a name to each camera single camera.  I hope this will be useful for you.

  In addition, there is a bit of discussion on this topic on the forum of discussion already.  Check out these related threads, or use the search box to search for more.  There is much information available!

  http://forums.NI.com/T5/LabVIEW/multiple-USB-cameras-in-LabVIEW/m-p/833517

  http://forums.NI.com/T5/machine-vision/two-USB-camera-identification/m-p/2193960

  http://forums.NI.com/T5/machine-vision/synchronized-capture-for-multiple-USB-cameras/TD-p/1879647

  http://forums.NI.com/T5/LabVIEW/multiple-USB-camera-image-acquisition-using-vision-acquisition/TD-p/...

• How to take snapshots of two usb camera at the same time

  Hello

  I have a project where I have to take still photos of two usb camera at the same time repeatedly and save the in a particular direcltory. I am received using a camera by using "Camera Grab vi", but I can't make it work with 2 cameras, I use the flat sequence and 2 "Camerra Grab vi: with particular camera in a sequence, but each time when I run the program I get only pic of a camera, its seems a camera dominates the other.»

  Please is it possible to use the two camera simultaneously. Attached are the snapshot of my vi.

  Thank you

  Ankit G

  Looks like you are using the same reference at the same time grabbing the camera. The two camera snaps happen but the second camera clamp is written on the first so it seems alone is slam. Try to run the VI executiong highlighted arbitrary mode (select icon icons four bulb to the right of the button run on the schema). This will allow you to see the data stream. In order to get both of these Snap you'll need separate references. You can try to watch one of our examples in the example Finder OR give you some direction (LabVIEW > help > find examples > Browse tab > Input and Output material > IMAQdx > high level > Snap.vi). You can break the two cameras at the same time if you just copy this code and double of the code.
  (Note: If you change the examples, always save as copy in another location so that you do not save on the packed example)

• Email sends two copies of e-mail to the recipient

  Original title: program compatibility Application Applications App Apps game games Legacy Crash crashes Hang hangs

  My email account send two copies of the same message every time I have send a message - that is to say whenever I have send a message, the recipient receives two copies of the same message. What should I do to solve this problem of e-mail "double"?

  This behavior is usually caused by an anti-virus program that has been integrated with your e-mail program.

  Uninstall your AV, reboot, reinstall the AV without the integration of messaging

• Clips on a shoot with two cameras

  I'm was scheduled to begin shooting a film in a few days, which will involve my F55 and an F5 as second camera. For installation, there will be a PMW-200 as the third camera. Just called me to say the naming convention clip that they wish to use for both cameras, and I just got the eggy conversation where I explain that this is not possible right now. The firmware was updated. To come. Blah blah.

  The cameras will be time synchronized jam.

  I wonder if someone has suggestions for how unambiguous and easily differentiate between the two cameras. The ideal would be to change the clip naming, perhaps in the content browser, but I don't see a way to do this.

  Thanks for this Leon. Clip browser it and let the wrangler data to worry about this. We are actually recording to SxS rather raw, so I hope that with my setup enough vanilla and a very little bit of tweaking things must be upward. I intend to shoot mechiers at the head of each location.

  200 gets specific coverage for a scene so I'm not too worried about the match up there; This choice of camera was production and dictated by the budget.

  Speaking with the customer we discussed lockits, but decided to digislate and frequentish jams. Years ago, I came across a problem with a specific batch of Digibetas that has blurred the timecode so continually fed an external signal. It was salvagable to the end, but headache than the left lingers as well with the other weaknesses that I'm getting used to this camera and after having heard about free delivery issues, others have mentioned I thought it is better to let the lockits this time!

  I am in England so shoot 25 p. So far, I used the camera with the crossing record, in part because of talk of free running jumps (possibly a message by you). What was your rate when you have had free delivery issues and you have noticed with firmware 1.13?

• Editing a shooting of two camera in first 13 items

  I have two video tracks of a session of two camera of a part of the school that I'm editing together into one. I use one as the main video track and the other as a great shot in Cup. I would like to see the two video tracks play simultaneously-by-side at the top of the editing screen so that I can more easily choose which shot to use. How can I get there?

  [Left Pro for first things first... MOD]

  Step 1. Synchronize two videos.

  Move the two videos (from two cameras) in the edit window, select all four titles (two video tracks and two audio tracks) and right-click, then click on "Sync" and select "audio". Then the two videos will be synchronized by their audio. And now, you can cut any part you do not want to appear in the video.

  Step 2. Position the two videos with the PIP effect.

  Under "Effect", click "Presets" and then "PIP" (picture in picture), then "PiPs of 25%", drag he'S (LowerLeft) to the video track that you want the video showing on the left side, this will make what to see the video on the screen, he'S centering to a 25% of the full screen size. The another video track that you want to display on the right side, then drag LR (LowerRight). This will make this see video up on the screen, centering LR to a 25% of the full screen size.

  Step 3. Adjust the size and position of the two videos.

  Click on the video track located on the LL, go to 'Effect Options', click on the "fx Motion", change "25.0" to "50" wide, it will change the video size to half the size of the screen. And then play with the numbers in position adjustment until the video's position in the center of the left size of the screen.

  Then do the same for the other the video track. Click on the video track located on the LR, go to 'Effect Options', click on the "fx Motion", change "25.0" to "50" wide, it will change the video size to half the size of the screen. And then play with the numbers in position adjustment until the video's position in the center of the right size of the screen.

  There you go. Perfectly synchronized and placed side by side.

• How can I sync 2 sony AVCHD images from the camera on the "date" as a prelude and import it in first pro?

  I have 2 sony camera popular with the AVCHD file structure. The two cameras are the same. How can I sync 2 sony AVCHD images from the camera on the "date" as a prelude and import it in first pro? Im working with 6.0

  
  

  Now I see the date taken in the import screen until I click "ingest". When in the trash, this option is there, but no metadata in there. It is therefore impossible to import images from two cameras and have these sorted.

  
  

  How can I get this sorted out before, so I can export for the first?

  Thank you. Tom van den Dool
  

  Hi Tom,

  How can I sync 2 sony AVCHD images from the camera on the "date" as a prelude and import it in first pro? Im working with 6.0.

  Sorry, you can not do as a prelude. You can request a feature here: http://adobe.ly/feature_request

  Thank you

  Kevin

• Control several cameras with Codec C60

  Hello:

  I have a client who wants to use 3 PrecisionHDMC cameras and with the intervention of content to a codec C60, as well as an AMX control system.

  I understand that there may be only 3 video inputs connected to a C60 both, my question is:

  If I have a HDMI switch which video switches of 3 cameras connected to Video Input #1 the C60 and have that is configured as an input of the CAMERA, how to control the cameras independently?

  I usually sign my AMX for the C60 system RS-232 and send an order which said in effect "Hey C60, 1 camera to zoom before saying" or "Hey C60, say camera 2 to zoom out, etc...

  But in this case, the C60 will be only 'think' it has a camera connected, therefore:

  Can I still send commands via the codec that say things like 'hey C60, say 2 camera to zoom out,'

  OR

  I can "daisy chain" cable between them and simply connect RS - 232 to the 1st chain camera and tell them '' camera 3, zoom ''?

  OR

  Need me a RS-232 connection distinct to each camera and just say "camera zoom out.

  I hope I explained my question quite well, I look forward to your responses!

  Thank you!

  If you want to integrate a bit more flexibility and discreet control, you can add a small matrix of switching in the project (see Extron DXP 44 HDMI) and have then each camera connected directly to the AMX for control. This allows the discrete control, discrete video selection, output preview and the ability to also have a PC or other video source connected (3 cameras and a PC).

  Discrete control is possible with chaining with addressing, but according to the placement of the camera and the distances between the camera the Garland cable runs can a problem and since you have to run the video towards the grid it's easier to run the control back on location as well.

  If you want to use the composting and then the TC console should be used.

• I got two sources of camera the same audio recording - how to use multicam to audio synchronization and display TWO cameras simultaneously

  I had two sources of camera recording the same audio - I want to be able to do is use mulitcam SYNCHRONIZE the audio and video at the same time and be able to use the two clips simultaneously in a video - multicam - how can we use the TWO videos? In Multicam, I can only go to one video at a time - is to detach anyway, so I can trim two camera responsition camera and 1 on a 16:9 screen? What would be the best way to do this? Any help would be welcome - Ty

  

  Two PPut copies the multicam in editing element, one on the other.

• When you use the camera of the iPhone APP to send an e-mail, there is no saved project and I lose the message.  Is this normal?

  When I use the camera of the iPhone APP to send a photo by e-mail, I find that I lose the message when I change to another application.  Basically, no project is not registered anywhere.  Am I missing something simple?  Ex: Open Camera APP, select the image for the email, and then try to open the calendar, and then return to the message to add more content... where he?

  I had never tried your method before, but after testing three times, I got the same results as you did. However, if I manually saved the project (press Cancel, then save the draft) in the camera application, it was recorded in the messaging application, when I went there. If I use the photos app to send the photo to go, I can start the email, launch another application, return to the Photos app and the email is always on the screen.

  IF you want to send a picture with an email, do not use the camera application. There is no need to do so. You can use the messaging application or the photos app in order to attach a photo. You have access to all your photos in an application.

• In a with two cameras a multicamera edit does not appear in the multicam monitor?

  In a multicamera CS 6 with two cameras one Assembly does not appear in the multicam monitor or rather remains black while it is present in the sequence? Is this due to lack of memory of the CPU? I have a Toshiba Tecra i5

  Thanks if anyone knows why?

  [email removed by Moderator]

  I use Adobe CS6 first

• two camera entrance, showing the language

  Hi all ^_^
  I have two questions, one
  I had a show on a local television with a male character and it works great but now the producer want to kill me with the other character, now it's 'man and woman' to do a talk show for children-_ - im asking how can I input multi cam so I can move my character two with two cameras and two persons acting for the stage with two
  and how do I synchronize lips

  the other
  It's a funny show so some time actor some time show his tongue can I add language efforts to the mouth in the Illustrator file?

  Thanks ^_^

  > How do I input multi cam so I can move my character two with two cameras and two persons acting for the stage

  Ch can follow only a face at once, so for live production, it can maintain only a single character. But with two computers, each running HP, you could produce two characters live. Then you need to use a software like Wirecast of Telestream screen - scrape the results and disseminate on a third computer where you combine them, maybe with an another Wirecast? Not sure he can do it, but people from Telestream can tell you.

  > It's a funny show so some time actor some time show his language can I add language efforts to the mouth in the Illustrator file?

  The simple way is just to add an extra mouth with the tongue out and give it key elements of (name of the layer as "TongueOut (T)!"). Press and hold the T, when you want to see the language.

  If you want to keep the language hanging out while you talk, you would need two sets of visemes (i.e. two groups of mouth), and then you would trigger the Group whole language-mouth with a touch of the same way. It's more complicated, however, you need to apply a synchronization of the lips and face additional behavior to the Group of extra mouth.

  The next version of preview (3) will let you just press the trigger key and do not have to hold it down.

• When you use the camera application, it will take two photos at the same time.  The first is in the shot, but the 2nd has movement, say a movement arm or head.  Weird.

  I use the 6s and do not have this problem, but at a rally over the weekend, TWO others in the Group showed me the instances of this weird thing.  I'm a photographer by profession and like solving problems.   Cannot understand this.

  Probably "Live Photo.  Read the photo section of the manual here.

• Two wiggles in the same position of the camera

  Hello!

  I have a huge problem, which I suppose you can help me with, guys. So here it is:

  I use a wiggle in camera position expression:

  startFrame = framesToTime (492); stopFrame = framesToTime (670); easeOver = framesToTime (20); FREQ = 0.5; amp = 35; If ((temps > = startFrame) & &(time < stopFrame)) {if (time < startFrame + easeOver) linear (time, startFrame, startFrame + easeOver, value, wiggle (freq, amp)); if (time > = stopFrame - easeOver) (linear time, stopFrame - stopFrame, easeOver, wiggle(freq,amp), value); else wiggle(freq,amp) ;} value other}

  which wiggles basically the camera of the chassis 492 to frame 670 (with a bit of initial and final images mix). I would use the same expression for the same device and the position, which will begin at the 860 member and will end at 920, but... When I use the same expression, simply copy it into the existing: it uses essentially the second without the first.

  So my question is - how can we force them both to work for me?

  Thank you

  Harshit Bahl

  Designer
  

  http://suntechinteriors.com
  

  Hard: if set of statements for your expressions of dividing them into sections.

  Easy way: parent the camera for anal and apply the second expression for the No.