Collaboration and telepresence Solution

Similar Questions

• Video-conference using SX 20 and telepresence ISDn device link

  Hello

  I have a cisco SX 20 and device connection isdn telepresence device. the procedure via below I have configured and coupled unit SX and telepresence

  Step: 1

  address configured static Ip add via remote control.

  Step: 2

  using static ip, I have connection to the SX 20 device, using the browser. (ip 10.1.1.2)

  Step: 3

  Configuration--> devices--> manage ISDN link--> click--> click combined with research

  Step 4

  In ISDN configuration of the link--> I have ISDN numbers entered the repertoire. Subsequently, it works fine.

  Problem:

  End of test, cancel us the twinning of the device and restart the SX 20. Subsequently, we are unable to pair the device of telepresence.

  While click Display message (No. DEVICES DETECTED) the search button.

  Please share the solution on an urgent basis.

  Thanks in advance.

  Rgds

  Vetri

  Did restart the ISDN link solves your problem?

• HP Office Jet Pro 8630: JO 8630 Pro and HP Solution Center work together

  I had a HP Photo Smart C7280 that crashed. I replaced it with this 8630 Pro JO from HP and HP Solution Center software does not take account of the new printer after that the online setup process was completed. I used the software regularly and I would use it in the new printer as well.

  Hello

  HP Solusion Center software has been replaced by the most recent model HP Printer Wizard, it is not affiliated with the 8630 anyway.

  You can access the wizard in the HP printer by opening the software HP Officejet Pro 8630 from your desktop or in the start menu > programs > HP, open the folder that is listed as the printer model and then click the printer model icon.

  Kind regards
  Shlomi

• I have problems with the installer of Windows and Windows Update, and the solutions that I found for the two each rely on the other broken system to fix the first.

  I use a laptop HP Pavilion dv4-1220us with Windows Vista Home Premium Service Pack 1, a 64-bit operating system, and I have problems with Windows Update and Windows Installer. When I try to install programs, I get the following, or substantially similar message without the error code:

  "Error 1719. The Windows Installer Service could not be accessed. This can occur if Windows Installer is not installed properly. Contact your support team. »

  So I tried to download Windows Installer 4.5 and install it. When I try to start the installation, it always hangs on the first step, "Initializing Installation."

  After searching for a solution to this problem, I found that Windows Update may have a solution. So I downloaded the 64 bit version and got a file named 'file Windows6. 0-KB942288-v2 - x 64. I tried to run this file. He opened a box that said, in order "Prepare for Installation", "Full Preparation", and finally "Searching for Updates ', before you open a second box, which reads" click OK to install the following Windows software update: fix for Windows (KB942288). I clicked on OK in this box, which opened another box, which says at the top "updates are installed" and in a smaller section, "initializing for Installation................... »

  However, no matter how long it works, it never gets past "Setup initialization."... »

  So I tried to run Windows Update in Control Panel. He ran for a while, before giving a message saying "to check the updates, you must first install an update for Windows Update." I clicked on the button that says "install now". He has flashed, a moment, "download and installation of updates' before you go to the"check for Updates"and then he brought back the exact same upward ' to check updates, you must first install an update for Windows Update" message as before. I clicked install now once again, only to go into the exact same loop. After about four times in a loop, I gave up on it.

  So I tried to install Windows Installer 3.1v2, which took a while before saying "not enough memory is available to process this command." and the abandonment of the installation.

  So, I tried to download a program from 'Mr. Fix - it' of Microsoft. It downloaded fine and then failed on installation, because of the same Setup error I received initially.

  Finally, I tried to restart my computer and each solution is represented. Then I clean my computer and each solution is represented.

  In conclusion, the mistakes that I have in Windows Update and Windows Installer cordoned off each other, as the mistakes of each program are based on the other program to be repaired. I'm at my wit's end here. My computer works fine without one, except that I can't install new programs. I can access the internet fine, access files fine, all my scans have developed own... I don't really know what is happening. Can someone help me with this?

  Try the sfc scan:
  http://support.Microsoft.com/kb/936212

  If not, repair of Vista:
  http://www.Vistax64.com/tutorials/88236-repair-install-Vista.html

• I have a desktop with Windows Vista. Many times, the screen is the gel with an error massage "video Mode not supported". What could be the problem and the solution. ?

  I have a desktop with Windows Vista. Many times, the screen is the gel with an error massage "video Mode not supported". What could be the problem and the solution. ?

  Hi Izzy Nagar,

  ·         Exactly when you receive this error message?

  ·         Did you do changes on the computer before the show?

  ·         Do you have any extended monitor connected to the computer in the past or at the present time?

  Follow the suggestions below for a possible solution:

  Method 1: You can try to reduce the resolution of the screen (lower), then check if the message still appears.

  Check also if the refresh rate of the monitor is set correctly and check the manual of the monitor for assistance.

  Ways to improve display quality

  http://Windows.Microsoft.com/en-us/Windows-Vista/ways-to-improve-display-quality

   

  Flicker of the correct monitor (refresh rate)

  http://Windows.Microsoft.com/en-us/Windows-Vista/correct-monitor-flicker-refresh-rate

  Method 2: Use the option ' enable video low resolution (640 × 480) "start, then update your video card driver and check if the problem still persists.

  a. click the Start button, click the arrow next to Shut Down and then click on restart.

  b. do one of the following:

  ·         If your computer has a single operating system installed, press and hold the F8 key as your computer restarts. You need to press F8 before the Windows logo appears. If the Windows logo appears, try again by waiting until the Windows logon prompt appears, and then stop and restart your computer.

  ·         If your computer has more than one operating system, use the arrow keys to select the operating system you want to start in safe mode, and then press F8.

  c. on the Advanced Boot Options screen, use the arrow keys to select activate video low resolution (640 × 480) and press ENTER.

  d. connect to your computer with an account of a user who has administrator rights.

  e. If you can see your desktop, there is a problem with your video card. Try to update your video card driver. For more information, see the article:

  Updated a hardware driver that is not working properly

  http://Windows.Microsoft.com/en-us/Windows-Vista/update-a-driver-for-hardware-that-isn ' t-work correctly

   

  I hope this helps.

• HP Photosmart C310a and HP Solution Center Windows 8

  HP Photosmart C310a and HP Solution PS_A10_07_C310_FSW - installed Full_Win_WW_140_408 Center. Print from Internet Explorer 10 preferences pages rise in Japanese or Chinese.  Works fine in Word.

  Windows 8 running on Ultra Intel Core i7 laptop.

  Not a printing problem, but a problem becomes the prefrences page if we can settle Dulpex or 'print page 1-2' can't read pages.

  Actually have two Ultras (wife and I), and both do exactly the same thing.

  How can I solve it please?

  Hi, dash,

  If you have this problem with the browser Internet Explorer 10 and not with any other application, then it would be some setting in the browser IE 10. Try printing from another browser (firefox or Chrome) and let me know if you have the same problem?

• Whenever I open my Kodak easy software, that he told me that he stopped working and no solution to the problem.

  * Original title: software problems

  Whenever I open my Kodak easy software, that he told me that he stopped working and no solution to the problem. How can I fix this?

  To allow a person to better help you, can you provide more information please.

  for example:

  • What is the full name of the 'software kodak easy' AND its version number?
  • Is it intended to be run on this version of Windows 7, or if it was originally intended for an earlier version of windows?
  • What is the exact error message when it does not work?
  • He has already worked on this computer? If so, when did it stop working?

  If it is your program - http://support.en.kodak.com/app/answers/detail/a_id/36670/selected/true - it seems that it is no longer available for Windows.

  If you have a 64 bit OS, it can help - http://support.en.kodak.com/app/answers/detail/a_id/30535/~/easyshare-software-on-64-bit-computer-running-a-windows-7-or-windows-vista/selected/true

  If it ran on an earlier version of Windows, but will not work on Windows 7, try running mode of compatibility - http://www.sevenforums.com/tutorials/316-compatibility-mode.html - which may allow some older programs to run on a later version of the operating system.

• Premium insurance of Collaboration, and provisioning of VM requirements

  We are currently evaluating the assurance of a privileged collaboration and provisioning for our environment. I'm finalizing the requirements of the VM, but I see conflicting information on the docwiki. Our farm is running VMware 6.0 and I would keep consistent in all areas. A person built insurance 10.5 and commissioning on a VMware 6.0 and had it working well? I see the information on Docwiki below.

  Insurance (Version 10.5):

  support for versions of vmware esxi 4.0, 4.1, 5.0, 5.1, 5.5 =

  Source: http://docwiki.cisco.com/wiki/Virtualization_for_Cisco_Prime_Collaborati...

  Commissioning (Version 10.5):

  decision-making in load of the versions of vmware esxi = 4.x, 5.x, 6.x

  On the other end Cisco first as mentioned guide below shows that small and medium-sized deployments have ESXi 4.1, 5.0 and 5.1

  System requirements - Server and system requirements for the Client

  Privileged collaboration runs on any certified hardware VMware ESXi 4.1, 5.0, and 5.1 installed. Deployment of large and very large models requires ESXi 5.0 or later.

  Source: http://www.cisco.com/c/en/us/td/docs/net_mgmt/prime/collaboration/10-5/q...

  Also the docwiki clearly mentions that the version premium insurance starting with 11.1 is supported on esxi 6.0. If this is the case we run handler calls 10.5.2 within our environment, and in the case, we choose to build 11.5 for CPA and CFP would there be concerns or difficulties to integrate with CUCM 10.5. I think not but want to confirm. I would also like to hear thoughts on the CFP, APC version 10.5 supported ESXi 6.0?

  Thanks in advance!

  I questioned the engineering, marketing and the TME teams on the requirements of EXSi and they confirmed that the PCA EXSi versions listed are correct for 10.5.  Isn't that APC 11.0 out they began to test and support 6.x EXSi revisions.

  I have a different point of view on this issue. Why bother running 10.5 when 11.5 last rev for the CFP and the APC? 11.5 supports the towers to CUCM 9.0. We had a lot of problems with versions 10.x (updated the architectures, last minute, adds, etc.) and cleaned up emissions upward with the 11.1 and ensuites.  It is also not a good idea to get too far behind in number of revolutions from the point of view of the update.  Unless you use a cluster of CUCM 8.x (which I think should be the end of support now), you must move to 11.1 PC or later version.

  Concerning

• What is the origin of the creative cloud eating my space and no solution?

  What is the origin of the creative cloud eating my space and no solution?

  Please refer to: https://helpx.adobe.com/x-productkb/global/high_cpu_usage_cephtmlengine.html

  Concerning

  Stéphane

• Backup and restore solution

  could you give pls document me level backup and restore solution on vmware environment? Thank you

  ... all level backup and restore solution...

  Could you please be a little more specific.

  What you are looking for? Product specific or features...

  André

• You use Mac OSX 10.7.5, when you try to open a PDF file, I get a message "an internal error has occurred." I uninstalled and reinstalled both Adobe 10 and 11. Anyone know of the problem and the solution?

  You use Mac OSX 10.7.5, when you try to open a PDF file, I get a message "an internal error has occurred." I uninstalled and reinstalled both Adobe 10 and 11. Anyone know of the problem and the solution?

  Hi Charles,

  
  

  It is specific to a particular file or all the files that you are trying to open, gives you the error.

  How you open the same file using Preview on Mac.

  
  

  Thank you

  Vikrantt Singh
  

• Standalone telepresence solution

  Greetings,

  I wanted to ask you if there is a solution to deploy cisco Telepresence to autonomously, i.e. without

  integration with CUCM.

  Kind regards!

  Of course, you can get a Cisco TelePresence endpoint (as C - / EX-/ SX-/ MX-Series) and simply use a h323 IP 2 IP call.

  Presentation of the telepresence product:

  http://www.Cisco.com/en/us/products/ps7060/index.html

  Works well, but I prefer a call as VCS or CUCM control!

  If you think internet connectivity and you have to manage home offices / nat / firewall /...

  a VCS Expressway Starter Pack could be useful:

  http://www.Cisco.com/en/us/prod/collateral/ps7060/ps11305/ps11315/ps11337/data_sheet_c78-697075.html

  There are also companies (like us) who offer recordings of endpoint, so if you do not want

  worry not operating or investment, this could also be an option.

• Gateways and telepresence SX Gatekepers

  Hello

  I design a service project of video-conference with a client with 16 sites, one a seat.

  I decided to go with the codec of telepresence sx 20 or 80.

  Since this is my first project in collaboration with cisco, I need to consult certain documents or information on this implementation requirements. With the exception of telepresence, I need to know if I need to access the network controller, gateways.

  I saw somewhere that gatekeeper is optional. Means that a guard is not necessary for the translation of control and signal address?

  Can someone give me the minimum requirements for the network, network equipment, necessary roles for this implementation?

  Thank you

  Julian

  Hi Julian,.

  Allow me to pass this message to the community of telepresence to join the appropriate group of experts to help you.

  I hope this will help you get faster responses.

  Dejan

• Pictures killing an internet connection for the entire network in El Capitan and Sierra (solution)

  I hope this helps someone out there.  It took a lot of research and trial and error to figure.  It's a solution and not a question, moderators, please put this in the correct area - I'm sure that's probably not the right one.

  QUESTION: My Internet crashed and this was the situation for several weeks.  I used a hotspot from my phone for connectivity, it was so bad.  If I want to run a speed test, she would record .03Mbps.  Company Internet is out (twice), replaced new modem, dial-up, everything.  Modem became a signal strong, but it was not to reach all devices.  Literally spend days trying to understand this - constant speed running test.  Type a chance, but I noticed that if I turned off my wi - fi, my other devices to get internet antenna full.

  This is my note to the At & T internet tech:

  «I realized the problem - it's a mac question.»  If you see this once again, it's how to diagnose.  If they have a mac running El Capitan or Sierra (both latest versions), it will be a feature for the Photo program that attempts to download all your library - and sometimes loops constantly (this is the bug). When that happens, it will take ALL the bandwidth and choke the internet.  The way you can tell, if you turn off the WIFI antenna on the mac and the speed goes back to normal on all other devices.   You can see if you look at the activity monitor - the Application folder-> utilities-> monitor program - > Network tab.  You will see a function suck bandwidth, called NSURLSESSIOND.  Immediate fix is to run the PHOTOS, click on the PHOTOS-> PREFERENCES-> TAB, either "iCloud library" iCLOUD deselection or pause the update photograph (it does for 24 hours).  Network activity will return to normal, resolved to connectivity issues.  NOTE: you'll still the problem, if connect you the computer to the modem, wifi so isn't the issue. »

  I hope this helps someone!

  Interesting, but I didn't and isn't the problem with El Capitan or Sierra on more than a Mac. It takes some time to download a large Photo library according to your connection speed. I never knew 'loop' a Photo. Maybe some have. Could be a bad installation.

• Firefox blocks right after the start and no solution

  Hi all, there
  Directly after startup, Firefox freezes and keeps hanging.
  Everything started after I visited a free site where supposedly the training for the formula 1 would air... it happened via Sky... is what I remember.

  I followed all the advice and did remove all the profiles of boards and to install Firefox, installed again and
  replaced the profile that I had saved.
  Since this morning 4,00 o clock and still no results at 12:15.
  Someone at - it a good solution that can make me re install without losing valuable information that belong
  my Firefox and goes back a dozen years.
  Right now I use Safari to find answers to my problem, but he likes to go back to FF.

  Hope to hear a good word...
  Kind regards... Hanszio Hungary

  Hello, can you create a new profile using the profile manager.

  • http://KB.mozillazine.org/Profile_Manager#Mac_os_x

  If it works, you can recover some files from your old profile

  • Recovering important data over an old profile