collection of data & graphical CTS (M-24) using the serial port

Similar Questions

• Using the Serial Port on the HP 50 g graphic calculator

  Hello world

  I have another question. I want to use the Serial Port on the HP 50 g to connect with another device. The device is called the MFJ-1214PC. What it does is to accept the text and commands through a 9-pin serial Port and converts the text in a Code Morse/RTTY sound audible. It also decodes Audible the Morse Code and RTTY radio signals and displays them as text on your computer. The program that controls the MFJ-1214PC was originally written for an IBM PC for the MS-DOS operating system. The HP 50 g graphic calculator meets the system requirements for the simplest version of the program. I was wondering if there is an MS-DOS emulator written for the HP 50 g, which would allow the HP 50 g to become the computer in this case, or if the program could be rewritten and brought to the HP 50 g. If it could be rewritten, programming language what do you think would be better suited to this type of application (if it is even possible?) or UserRPL, SystemRPL or Assembly. Don't forget that I'm a complete newbie with the HP50g and have never programmed with it yet. I'll include the manual of the MFJ-1214 PC as an attachment so that you won't have to look for him. Thank you in advance for your help!

  ~ Zekelegge ~.

  I understand (from my brief overview) out of the box-MFJ-1214PC, this offer box decoder output series computer.  The computer (50g in your case) will have the software to read message series and then convert that to an output for display.

  BartDb gave you the right answer.

  A serial cable with the correct speed level and reversing lever to manage as well as the 50G has a RS-232 signal to the outside world is the ideal solution.

  However, make sure that the output of the decoder box series package can be understood by the 50 g. aud, bits, etc.   (you have the set-top box manual, so you'll have to look that up)

  the streamsmart is not an aggregator of serial port.

  in other words, these connectors DIN of Qty 4 on the front do not accept series rs-232 input and send then to 50 G.

  I'm not an expert, streamsmart more info on these boxes is rare to find.  The probes are even more rare.

  However, I know that the 4 connectors are for the analog-to-digital conversion in the probes.  The streamsmart works as a "data logger" in which he sees the input probe, the A/D converted, then sends it to the 50G (or a computer via the USB port).

  In addition to the solution of Bart, there was another named Tiwag forum poster who created a serial cable and displayed a schematic representation of the cable.  This information can be found here:

  https://groups.Google.com/Forum/?fromgroups#! searchIn/comp.sys.HP48/serial$20port/comp.sys.HP48/ltcane1jSOw/uHyw2Ti03kgJ

  to see an example of programming to use the serial port of 50G, you can reference the following hpcalc GPS data collection program.

  http://www.HPCalc.org/details.php?id=7105

  It is written in userrpl so can be crossed with the reference of users advanced for the translation of the syntax.

  It seems that the main routine of concern for the comm to the gps is in the file "GPS >.

• Using the Serial Port for data acquisition Non-Serial

  I searched the forums and can't find anything on this topic.

  I saw that it was possible to use the parallel port for e/s digital single and I was hoping that the serial port can be configured the same. It seems all VI VISA only to use the serial port to receive ASCII characters at a given flow rate, but is it possible to simply query the status of the line series at my own speed to see if it is high or low, kind of like a single pin DAQ?

  It seems that it would be possible until the serial data are read and controlled by labview, not Windows. Let me know if you have ideas of how to approach this problem, or any comment as to why it is not possible.

  Thank you all!

  Select the property > settings series > Modem of the line parameters. For example, the State of the CTS is an entry to the pc.

  With the help of these lines is a very poor substitute for a scope or map DAQ. The only things you can return is Asserted, Unknown or Unasserted. The range of acceptable signals is important enough. Anything between + 3 and -3 is an unknown state. Your other signals is + / 3 to 15 volts. What type of signals do you really want to capture?

  Edit: there is no such thing as a visa so I have no idea of what you actually use.

• How use the serial port read and display the text but not scroll off the screen?

  I'm new-ish/return user fan of Labview and trying to change the example VI "Advanced serial write and read VI" is the part of the dev suite 2012.  I need to use the string box for ALL of the text from a serial port, always adding and just roll off the screen when the actuals come to the serial port.

  What actually arrived more than bytes (or no bytes AT ALL!), during reading time text, current rolls out of the box in the chain.  Even when receiving 0 bytes, screen is removed.  I'm not very familiar with the locations of functions and even worse to understand obscure references to functions, so please keep very basic answers so I can follow.

  Just to be clear, I need window of the chain behave as HyperTerminal does always displays the data and it is not pushed by window arbitrarily.

  Thank you

  Steve

  A long shot.

  Is that what you want?

• Problem using the serial port with windows 7

  Hello

  I have a modem of SIM cards (used to update remote controller of the electronic gate) that connects to my computer via the serieal port (COM1).

  The modem comes with its own piece of software that worked fine on my old computer with windows 7 (I had a similar problem, but then I just need to update the driver).

  I now have a new computer and I am unable to connect using the modem (I think I'm using the latest drivers for the serial port).

  Is it possible that I need an older version? If so, how can I get a?

  My motherboard is a GIGABYTE H81M-D2V.

  Any ideas?

  Thank you

  AVI

  Hi Avi,

  Thank you for the update on the issue.

  The UART, or Universal Asynchronous Receiver / Transmitter, is a characteristic of your microcontroller useful to connect serial data (text, numbers, etc.) to your PC. The unit switches incoming parallel information (in the microcontroller/PC) to series data that can be sent over a communication line.

  According to the description you provided it seems that your modem isn't connecting with your Windows 7 computer, then I would contact Duetech Berès your modem manufacturer, so that they provide you with the steps to set it up.

  Get back to us after contacting them and please get back to us with your question was last updated.

  Kind regards.

• Data NMEA which are received on the serial port, when the system starts causes windows 7 to interpret these data as a serial ballpoint mouse and moves the cursor jumping around.

  I know this question was asked several times before, but the solutions proposed, such as changin the registry does not help. It changes by itself. In the configuration that I have in my boat, the stream of NMEA data is directly injected into the COM port so no driver is necessary. It's a problem easily solved in windows XP, why is it so difficult in W7? There must be a way to permanently disable the plug-and-play driver load. I found this program that works only for Vista, if I understand correctly: http://www.stentec.com/en/download-freeware COM port plug & play blocker. If something similar could be provided by MS for W7, it would be very good...

  It turns out that the program at the port of Stentec COM (freeware) http://www.stentec.com/en/download-freeware care & play blocker, also works in W7. I don't know how it works, but it does, and it's good for me! It also works for the virtual serial ports.

• data acquisition in real time using the module sim900d (not arduino0

  Hello

  I'm doing my final year project. I'll send the data from a remote location using sim900d for the other module (sim900d) connected to my laptop. Now, I need to import data acquired through sim900d connected to my laptop in Labview. But I don't know how. Kindly guide me

  I looked for it and thus to find a link that uses the serial port to send to commnads

  http://www.codeproject.com/tips/583315/using-SerialPort-and-at-commands-for-querying-cell

  so now send orders AT serial number is easy. first of all examine the emitting part. for this you need VI config series VISA and VISA series write VI. You can serach these VI by right click I your new VI block diagram and press search on the top left corner. Here you type the serial port and you will get a list of the VISA series live.

  Here is also a link to or

• My verse ATT modem (non apple devices to use this modem} is connected to the ATT line, Time Capsule (iPhones, Macs Time Capsule use) via ethernet Uverse.) Non apple devices can collect data from iPhones or Mac using the time Capsule?

  My verse ATT modem ({use of devices not apple wifi of this modem} is connected to the ATT line, Time Capsule (iPhones, Macs use the wifi of the time Capsule) and connect to the Uverse modem via ethernet.)

  Both devices are set to the highest security and each uses separate passwords.

  Non apple devices can collect data from iPhones or Mac using the time Capsule?

  With a bit of work by someone who knows how to do such things, not Apple computers could read some files on the Mac if file sharing is configured on the network... devices non-Apple and... He knew the device passwords or administrator for Macs.

  Mac could also play the files on other Macs if file sharing has been implemented and the device password or admin was known.

  If you ask if a PC can read the files on the Time Capsule, the answer is Yes, without doubt, assuming that the PC knew the password of device for the time Capsule.

• I can get the data of a hygrometer using the RS232 port with the following T75.2F:H17.0% using a RS232 data logger format. I was wondering if I can collect this data for later analysis using Dasylab. Any help is appreciated.

  I can collect data from a hygrometer in a text file using the RS232 port with the following T75.2F:H17.0% format, these data are collected using a data logger software. I was wondering if I can collect this data for later analysis using Dasylab. Any help is appreciated.

  The setting below causes the error. Change for the second selection, output values of all channels.

  

• How to periodically send various types of data via the Serial Port?

  Hello! Everyone

  I have to send data to LabVIEW to my device on the Serial Port.

  I know how to send data on serial port in LABVIEW, I already have this part.

  Now the problem is that I have several types of data I need to question my embedded device, if I want to send the query periodically command.

  So lets say that my four Op Codes are the following, which will send four different types of query command to my device on the serial port.

  (To be honest only OP_LED and OP_SENSOR is used now)

  0, OP_SYNC

  1, OP_LED

  2, OP_SENSOR

  3, OP_FUTURE

  Structure of basic package is as follows:

  Header (0x2C), Checksum, length of the data (n bytes), Op_Code (1 byte), length (length of Code + data Op)

  For OP_LED, I need to send the package as follows:

  0x2c 0x02 0x01 0 x 00 0x2F (0x2F being the XOR checksum) (calculation of Checksum part is done and SUB Vi form)

  Length of the package this is 0x02

  0x01 is Op Code for OP_LED

  In the same way

  For OP_SENSORi need to send the package as follows:

  0x2c 0x03 0x02 0x00 0 x 00 0x2D (0x2D being the XOR checksum) (calculation of Checksum part is done and SUB Vi form)

  0x03 is length of packet here

  0x02 is Op Code for OP_SENSOR

  So, how can I do this periodically in labview, in such sort that period can be adjusted whenever necessary.

  Is there something in LabVIEW to do.

  I had done the reception and decoding part and working properly.

  http://forums.NI.com/T5/LabVIEW/store-data-coming-from-serial-port-in-buffer-and-then-take/m-p/32722...

  So I must implement read and write the part of same while loop?

  Do not insert in the table if you put data in an array at index 0.  Just use array to build.

  No need to have Visa to write don't be a part of wire to the wire of reference and error VISA go in the upper part.  These wires should go THROUGH the entry VISA.

  Don't your checksum requires all the bytes up through data?  Righ now, you only put the checksum on data bytes and forget the opcode and length bytes.

  Your sending is not the opcode for Opsync or Opfuture.  You just send the empty tables.  At the same time for the other two, you put the opcode in the data table.  All your original opcode in the table build thread.  Get the data out of these structures in case item which is supposed to represent the opcode.

  xpress_embedo wrote:

  Now it works but I have now two problems.

  (1) OP_SYNC and OP_FUTURE do not data, but still receive its data on serial port, can I do something here as I have nothing when the table is empty in the structure of the case.

  I do not understand this statement.  Perhaps my answer above will fix any issue you have here.

  (2) how can selection operation Code to be send is done using control façade but real application, this task should be automated to a certain frequency, like OP_LED package must go out to the serial port to 100msec and packet OP_SENSOR must go out to 1000msec, I do this.

  Now you agree a little more architecture.  I would encapsulate the code that is in the while loop as a Subvi.  Then with the hand of your program while loop, use two time Express VI, a game for 100 msec, the other for 1000 msec.  When an express VI is true, run the Subvi with a command set waiting for the answer.  When the other VI Express is true, have it run the Subvi with the other set of commands.

  The device responds with anything when you send these commands?  You only send data.  I see no VISA Read to be able to recover all the data.

• Store data from the Serial Port in the buffer and then take action?

  Hello! Everyone,

  I'm new to LabVIEW and I take assistance from various videos and stuffs available online to get started with LabVIEW.

  But I have a duty, therefore needing help.

  initially I see some of the tutorial videos and learned about the LabVIEW interface, and does a little project to communicate with the Port series (receiving and sending data).

  Happens to my task.

  My LabVIEW application will send a few State request packets on my device or control and based on the response packet that I have to display values.

  The Structure of package is as

  Header, length, Op_Code, data Checksum

  There is no terminator as newline or carriage return or anything else.

  In C language, I read the data from the Serial Port, and based on the length, I conclude that I got the full package or not, and then by recalculating the checksum value, the integrity of the package is verified and then based on that Op-Code has been sent will be decided.

  (I'm dealing with hexadecimal data)

  But how can I do this in LabVIEW.
  A tutorial or any referece will be useful for me.

  1. I suggest that you learn to use Shift Registers instead of local and global variables.  They are much more efficient (memory and execution speed) and make it much easier to read the schema.

  2. you don't need this inside the loop property node.  Is there a way to configure a Serial Port to turn off the stop character.

  3. you don't need to wait for playback VISA will limit the rate of loop if no data is coming.

  4. Once you have the length, you simply read the rest of the entire message and process it at a time.  This will make things a LOT faster.

  5. you should really do this enum a def type so that you can ensure that all your enum constants have the same values.  If you need to add a State later, simply update your enum in the same place then.

  

• Select the project of the serial port data

  Hello world

  The project aims to use labview to receive data from a serial port wireless. The serial port will receive two values (X 1 and X 2) every 10 minutes. I want to use these two values as inputs to my formula. How to make the selection? Thank you very much.

  Baicy

  Scan from a String.

  Using the first option and put numbers for zeros so that it shows some kind of significant result.

  

• How to trace data sent through the serial port by controlling simultaneously the buttons

  Hello

  I want to plot data by controlling the two buttons at the same time and the draw according to my control using communication serial port, but the problem is that the plot on the graph alternates between the two controls his do not change according to my control for example if I move the potentiometres1 / 1000 and button 2 to 4000 replacing these values on the graph I placed a select control, the problem is still not resolved u can help me please thanks in advance

  Regarding

  Samatha

  
  

• Can I use the SATA port connected to an optical drive to plug in a hard drive?

  I have a Pavilion e9270t desktop, Win7 Pro SP1, and I want to connect 3 HARD drive to the motherboard. Can I do this? Can I use the SATA port connected to an optical drive to plug in a hard drive?

  Thanks, CHemming

  CHemming,

  I've not seen UEIF support in the existing BIOS.

  If your demand on a 3T led, re - consider a maximum of 2 T.

  If you ask to have 3 hard disks, then you can do it without harassing the present cable of CD.

  The cage of your system hard disk will support 3 hard disks. Manual upgrade service

  All you need are the SATA data and power cables. Your Board has 4 SATA data ports.

  When you report back after inspecting your system for SATA power cables, I will move the cables and adapters, if necessary.

• How to read the data in a device connected to the usb port

  Is there a class or object, or the piece of code in Java that is comparable to the PDQComm32.ocx and the mscomm32.ocx used in VB6? I need to know how to read the data of a device plugged into the usb port of the BBerry. Is it possible to use the BB to read data from a device via a usb cable?

  I'm new in Java and I'm looking for the opportunity to write a project to read the data in a device with this program that can turn on a BB instead of on a pc.

  Thank you

  Did you watch net.rim.device.api.system.USBPort?

  That's what the doc says:

  Provides access to the USB port of the device.

  Avoid using this class in applications, as it is not portable. On the contrary, if you need to access the USB port, use factory CLDC Connector to serve a connection.

  Rab