Comments Windows 7 does not install the network driver?

Similar Questions

• Windows XP does not install the automatic updates.

  Original title: kopieerfout

  After several years, my laptop with Windows XP does not install the automatic updates, giving only a mistake:

  "

  ER is een doing opgetreden bij het van het bestand ntoskrnl.exe copying

  Kan het bestand niet naar doelmap copying.

  Everything works OK.

  Thanks for your help

  Everything works OK.

  It seems that it is not... Why Dutch? You use or have the corresponding language version installed?

  Free translation of message:

  "An error occurred during the copy of the file ntoskrnl.exe
  Cannot copy file to destination... »

  Please note that ntoskrnl.exe is a process in the cycle of the initial startup on your computer program.

  Try to load your "last known good configuration".

  The issue is also known to be caused by a short circuit in the ground cable into the keyboard cable. Make sure that it is not the cause of your error by replacing the keyboard with another keyboard or just disconnect the keyboard from the computer. You can also look at your function "Add or remove programs" If KB2686509 <> http://support.microsoft.com/kb/2686509 > is installed.  Install manually if it is not.

  If the above doesn't help, try using the Sfc.exe tool - see here > http://support.microsoft.com/kb/310747

  Or run the Chkdsk tool - see here > http://support.microsoft.com/kb/315265

  If still no luck, you may need to restore the file ntoskrnl. exe as follows:

  1 - insert the Microsoft Windows XP CD. Note: If you have a recovery CD or a restore CD and not a Microsoft Windows XP CD is probably the procedure below does not solve your problem.

  2 - restart the computer and that the computer starts, you should see a message press any key to boot from the CD. When you see this message press any key.

  3. - in the Microsoft Windows XP setup menu, press the R key to enter the recovery console.

  4 - Select the operating system you want to set and enter the administrator password.

  5 - type expand d:\i386\ntoskrnl.ex_ c:\windows\system32

  6. - you will be asked if you want to overwrite the file, type Y and press enter to replace the file.

  7 - type exit to restart the computer.

  Hope this helps - good luck!

• After you install a second WD 1 TB my book drive, Windows Explorer does not see the new drive.

  Original title: Signature Collision?

  I'm having hard to the installation of a second external drive. I use Windows 7 Ultimate RC. There was a WD 1 TB drive My Book already installed - healthy and works very well. The problem occurred after installing a second WD 1 TB my book reader. I followed all the instructions, pluuging the drive to a USB hub. Windows found the disk, installed drivers and reported the new drive ready for use.

  Windows Explorer does not see the new drive. Devices and printers shows 2 external drives from WD. Disk Management shows as 2 drives, but the second disk is offline because of a 'Signature' Collision

  Each player works very well if it's the only drive plugged in. "Eject My Book" does not work because a program (or more) are to use the player in the background (Windows or Norton).

  I installed the latest firmware and I'm still having this problem. I've been emailing WD with this problem and they are running out of ideas.

  Can anyone help?
  Thank you
  Comatose13

  Hello Comatose13,

  There is an old article of KB in Windows XP that has been recently updated with additional measures to solve this kind of problem. The KB covers Windows XP, Windows Vista and Windows 7 with step by step methods. See if that helps.

  http://support.Microsoft.com/kb/330140

  Bobby

• Install Windows 8 does not recognize the system drive

  I built a new machine (chart below). Since this is a new machine and not an upgrade, I bought Win 8 Pro 64 bit OEM to do a clean install. The SSD is my system disk that Windows 8 will be installed. Four data drives are mirrored, two for the other two. Construction went perfectly. The BIOS recognizes all six disks: 1 SSD, 4 HDD, 1 DVD.

  Insert and boot the disk of Windows 8. Accept the EULA, enter the product key. Arriving at the page "Where do you want to install Windows?", only four hard disks are listed. The SSD (installation to go) is not found by Win 8. ??? I tried to change ports SATA, cables, power supply - no difference. For each new change of hardware, the BIOS still sees everything. This isn't a hardware problem.

  The question remains: why the installation of Windows 8 does not recognize the SSD drive. All five disks are on AHCI. I'm not in RAID.

  I spoke with crucial technical support of all (manufacturer of the SSD). They were also surprised that the drive does not appear in the list.

  Does anyone have a solution? I spent all the money on hardware, as well as the new version of Windows and I cannot install it.

  This is the real kick in the teeth: Microsoft won't support me. The OEM of Windows 8 version is the same as manufacturers, such as Dell or HP. Support told me I had the support of the manufacturer. HA! I am the manufacturer. Either that or upgrade from an earlier version of Windows. This means that any that a new construction machine will get ZERO assumption of Microsoft. All just great.

  Thank you in advance for any assistance.

  Windows 8 Pro 64-bit (full version) - OEM
  Intel Core i5 - 3570K
  Card mother GIGABYTE GA-Z77X-UD5H
  Crucial Ballistix 2 x 8 GB DDR3 1600
  Crucial M4 2.5 "128 GB SSD (system disk)
  WD Green WD30EZRX x 4 (data readers) 3 TB drive
  Rosewill Challenger-U3 ATX Mid Tower Case
  SeaSonic M12II 620W 620 Bronze PSU
  ASUS DVD writer

  The DSS must be LOW LEVEL FORMATE.

  Once, there may be no other [HDDs] not connected to the SATA ports.

  Install Windows 8 Pro now.

  [Edit] Can someone please mark this as answered? I can't because I posted the question. Thank you.

• Windows 8 does not see the hard drive on the Satellite A200

  Windows 8 does not see the hard drive on the A200.
  How to install it?

  S strange Windows 8 should already contain the HARD drive controller driver to recognize the HARD drive during installation.
  The HARD drive is visible in the BIOS?

  Do you use the original disc from Microsoft of Windows 8?

• Qosmio F30 - 112 - Windows XP does not recognize the HARD drive

  Hello.

  I have a Qosmio F30-112.
  I tried to install the Windows XP Professional instead of the Media Center edition.
  However, during the execution of the installer, my laptop does not recognize the hard drive. Therefore, the installation cannot continue.

  I thought it might be a problem of corruption with my laptop and reinstalled Media Center Edition successfully.
  But when I try to install XP Professional it always gives me the same error.

  Suggestions for the configuration of the BIOS or solutions for why this is happening?

  Thanks in advance.

  Hello

  Just a question:
  You are looking for in this forum for other similar issues with regard to the installation of Win XP and lack HARD drive? I doubt

  The fact is that your notebook has a SATA controller and you need a SATA (Intel Matrix Storage Manager) driver.

  You should have a look here in this doc from Toshiba:
  [How to integrate a SATA AHCI driver into a Windows XP installation CD | http://aps2.toshiba-tro.de/kb0/TSB85017Z0000R01.htm]

  and should also search this forum for other threads

  Good bye

• I can't access my external hard drive with windows 7. How can I get my music out of her files? My pc with xp operating system can access it without problem. but my new pc with windows 7 does not see the hard drive.

  I bought a new pc to replace my old hp 14 months as the motherboard fried in. I bought a case of disk external hard to rocketfish to put the hard drive of my Windows 7 pc in. burned does not see the hard drive. my old pc with xp can access all the items on the external hard drive.

  Check that the drive appears in Device Manager.

  If so, go to disk management and assign a drive letter.

• Lost in car-Windows xp does not recognize the slave drive

  I do reinstall xp home, no problem when I did the system does not recognize the slave drive I have.  As far as I can tell that it's all hooked up correctly.  When I go into disk management it does not recognize the drive either.  All of the suggestions.

  Hi james.williams,

  1. How is the drive connected to the computer?
  2. What is the number of the brand and model of the player?

  I suggest that you check the jumper settings and make sure that the jumpers are correctly positioned.

  Make sure they are in the two master/slave jumper and not cable select.

• Recovering the Windows system does not recognize the hard drive

  Computer does not recognize the hard drive when booting.  Guard gives me 1782 disk error.  Then try to use the ROM installation thing and throw a disc hard test there is no option to test anywhere.  Computer was working fine this morning and then I stop when I turned it back on it was not properly start.

  I have a zt3000 running xp sp3

  someone please help me, thanks

  Hello

  Please reinsert the drive from the rear panel and check if the device detects the drive hard in case you have the same problem, then the hard drive is bad, you need to replace the hard drive and reinstall the operating system on the unit to return to its operating state.

• Windows Update does not install the updates from 14/04/2009. Error code 80070002.

  I'm running 32-bit Windows Vista Home Premium on a Dell Dimension E520 PC desktop with processor Pentium dual core and 3 GB of RAM.
  Reasonably up-to-date hardware. Well protected and all software security entirely to so far.
  My problem that goes from Windows Update is not install updates from 14/04/2009 and returns the error Code 80070002.
  I followed the advice and went in the Windows Software Distribution folder and remove all the contents of the data store and records downloads and tried again about thirty times now.
  I get regarding the acceptance of the license agreement and clicking on, ok, when Vista dims the screen and asks if I started it and then the error message in Windows Update, saying: "some updates were not installed."
  Is not a computer expert, I guess that what is described in help Windows Update error Code 80070002 is the same as 0 x 80070002 for which I found advice on a Microsoft page to save these commands
  net stop wuauserv
  CD %systemroot%\SoftwareDistribution
  Ren Download.old download
  net start wuauserv
  as a windows batch file and run as administrator.
  I now have a download folder and Download.old folder. Fascinating but no help at all!
  I infer that the numbers of 0x0 are my six error codes failed attempts to install Vista Service Pack 1, a few months ago who always ended up with an unusable computer suspended with a black screen and the white writing showing 46 thousand of 96 thousand file and something, followed by a number of 0x0.
  The only way I could get of these attempts was by booting from the Installation of Vista disk, masking the Service Pack 1 update and using the system restore, but that's another story.
  Have an impact on my current problem, I wonder?
  For absolute clarity are the updates that won't install:
  Explores update for Internet Explore 7 edition (KB963027) 14/04/2009 (Just editing that.) Typed a wrong number in a first time. Sorry).
  Four updates of security for Windows Vista (KB952004) (KB956572) (KB959426) (KB960803)
  Windows Malicious Software Removal Tool - April (KB890830). (I downloaded it manually and run it from my office and we found no problem).
  Update of security for Microsoft Office System 2007 (KB960003)
  Update of security for Microsoft Office Excel 2007 (KB959997).
  I'm at a loss what to try next.
  FYI, I use Uni-bleu Power Suite 2009, McAfee Total Protection and Ad-Aware Anniversary Edition with Ad-Watch Live on.
  I tried to do everything that it with Ad-Aware died, but my hunch is that the problem is in Vista ot the updates themselves.
  I'm quite competent with guests of orders, not to mention manually editing the registry!
  However, any help would be received with gratitude and I guess that if the instructions are evidence of fool I have very carefully follow step by step.

  I have the same symptoms: from a distinct point in time updates of windows works more and every time returned the error code 80070002.
  After a few hours, I found the solution: sfc/scannow reported the wuauclt.exe file.
  And the reason was: McAfee virusscan put this file in quarantine. He is falsely W32/Generic.worm.aa in there.
  Restore this file from the GUI of McAfee completely solved this problem.

• Windows 7 does not recognize the DVD drive! HELP need before March!

  Guys, my DVD drive was wrking a few weeks now, it's not. Windows 7 does not detect it shows in my computer or Device Manager it isn't freeking.

  Although, when I start my system, I checked it in the BIOS and it has been detected. So please help me! I need a solution before March 2012...

  Hello

  Do you know if there are major changes or downloads or something like that to the computer until the reader has stopped working?

  Have you tried a system repair on a date where the car worked very well?
  http://Windows.Microsoft.com/en-us/Windows7/what-is-system-restore

• Win 7, stand-alone windows installer does not install the msu downloaded on my HD files.

  I have several MSU files that I downloaded on my computer.

  I click on them and the stand-alone windows installer goes into "searching for updates on this computer".

  2 hours later, still nothing.

  I know that people have problems with the update of win 7... Nothing works.

  So far is just sitting there looking for updates... He ran all night... Nothing... always to research.

  I can not find where Microsoft puts the installed update files... If the software distribution folder, which wiped out during one of my attempts to resolve this problem.

  windows update told me today there were new updates available, and then sit there for 6 hours trying to get them with no result...

  So if I can't even manually install MSU file, what can I do? Try to install the kb3102810 fix

  You can use internet explore and access the catalog M$ and bring the two,.

  That is to say a right click and run as administrator

  

  Then go to the catalog and the top search right for each update and allows them to basket

  http://catalog.update.Microsoft.com/v7/site/install.aspx

• Does not install the audio driver for Portege M400 WinXP

  Hi all

  I have a Portege M400 (3G) and I managed to extract the Windows XP Tablet Edidtion the recovery DVDs. I installed Windows XP and all the drivers in the correct order (I've omitted some of the software I don't need) and everyting works fine (in fact, I am posting this from the tablet itself) except for the sound driver. He refused to istall and gives an error message that the software does not apply to this model; even if it is the only available page driver drivers Portege M400(3G).

  any ideas?

  Hello

  where to download the driver? On the European site? Maybe you should try the Canadian site, they sometimes have some drivers who hasn´t europe and maybe you can find the audio driver that matches:

  http://EU.computers.Toshiba-Europe.com/cgi-bin/ToshibaCSG/download_drivers_bios.jsp

  Otherwise, there is another option: find out which audio chipset is installed, visit the website of manufacturers of this chipset and download the drivers. Him to work.

  Welcome them

• Windows Vista will not install the usb driver for kobo reader

  I am trying to configure my reader Kobo following the indications, the PC does not allow me to install a USB driver for download, I tried many times

  but it keeps blocking.

  When you connect the device Kobo try to choose 'Manage the library', so the camera gets identified:

  http://kobo.intelliresponse.com/index.jsp?requestType=NormalRequest&id=1438&source=5&question=Do%20I%20Keep%20Reading%20or%20Manage%20Library?

• Windows 7 does not recognize the optical drive.

  My Optiplex 3010 refuses to recognize the drive R/WDVD.  It used to, but now does not work.  It does not appear on the list of Windows Explorer of connected disk devices, and on Device Manager, it has a yellow "!" next to it, showing the existence of some kind of conflict.

  Dell technician you changed every piece of hardware in the system, but there is no change.

  It is recommended to reload the operating system, but I'm not sure that's possible when the optical drive, which emerges my backup does not work. ?

  I tried the system restore, but there are only a few recent brand-places and this problem is ongoing for longer than this.

  So, is it possible to restore the operating system to health short to start all over?

  I tried your suggestion to see if the drive is recognized by the BIOS, and it is.  So, as you say, it's a Windows problem (no surprise).

  The thing that I was worried about most is having to reload the OS of my backup restore DVD disk using a disk drive does not work.  But, you pointed out that if the BIOS recognizes the drive, the disc should be readable.

  I just have to devote myself a day or two to reload all my programs applications to deal with another failure of a Microsoft OS to steel.  Grrr!   :- (