CompactDAQ ethernet shared by host 2 PCs

Similar Questions

• DASYLab Lite, CompactDAQ Ethernet, "the stream blocked by a later module" error

  I receive the message 'the stream blocked by a later module' and then the execution stops. I tried to remove the modules without change. He usually stops 8 minutes, 20 seconds (500) in the race. It happened on two different computers (same network, however). How can I get my program to run longer (forever?)?

  I am using a cDAQ NI 9188 (CompactDAQ Ethernet chassis), NI 9237 (strain gauge module), NI 9211 (thermocouple module), OR-DAQmx 9.5.1 and DASYLab Lite 12.00.01. My program of DASYLab affect strips from 100 Hz sampling frequency. The calculation of the average (reduce) block performs an average arithmetic with the size of the interval of 100 and a block size of output of 1.

  

  Thank you!

  Which module complains about being blocked? Look at the title bar of the message - it should show the name.

  You can observe the locking by turning on pre-trial block view-Animation-FIFO.

  I am suspicious that average organizes blocks more were awarded.

  One thing to try and really monitor your computer after doing this...

  Go to the Options menu in the spreadsheet view, then open the General preferences. Change these two settings - see the image - turning them off. The risk is that your application uses too much memory, so, please, provide oversight.

• RT target does not read shared variable hosted by host

  Hello

  I just started to move my LabView application to a system of RT, and I came up with a problem. When I host a shared variable network-published on the RT target, I can access through vi running on the target and the host (which is good!). However, when I have this host on the host variable (such as by simply dragging on 'My Computer' in Explorer projects or all create a new variable), the vi running on the target RT is not read.

  I wonder if there is a problem with my installation of LabView, or if there is some step I'm missing. Any suggestions would be greatly appreciated!

  My host is running Windows 7 x 64, with LabView 2009 SP1 32 - bit. The objective of the RT is a real-time OS-powered desktop PC. I have attached a very simple project to illustrate this problem: I start 'Target VI' and 'Host VI' at the same time. On 'Host VI', I change the values of the two shared variables: 'hosted host' and 'target hosted. Only the changes made to the target "hosted" appear on the 'target VI'.

  Thank you!

  Andrew

  Take a look at this link (software configuration and firewall hardware to support National Instruments products) and this link (configuration of firewalls and routers network address translating shared Variables) to see if this highlights exactly what you need to explain in your application regarding the definition of the firewall exceptions.

  David has.

• Can I create an internal network or isolated on VDS shared between hosts?

  We seek to deploy VDS on our site of recovery (for MRS). We have expanded network of level 2 so the primary site and recovery, guests can use the same IP addresses, but I don't know the best way to test the SRM. If I create a dvportgroup SRM, without a dvuplink, the dvportgroup may exist on all hosts that share the same configuration of VDS, but will be virtual machines connected to this dvportgroup be able to communicate on different hosts?

  Otherwise, what is a good way to achieve an isolated private network that can be shared between virtual machines that have the same IP address as production systems? A distinct community VLAN?

  They will not be able to communicate without a VLAN on the physical switch upstream.

  If you have licenses VCloud suite for POSSIBLE, you could create a VXLAN to communicate, but the easiest solution would be to create a VIRTUAL LAN.

• Sharing the host using Vcenter

  I have two machines with ESXi hosts on them, I created two virtual machines on each vsphere client using. Now, I want to share the memory, core and hard drive of these two hosts. Is this possible?

  Please answer as soon as possible

  Thank you.

  You cannot share of CPU or memory, because vSphere works as a failover cluster, rather than a compute cluster. Sharing of disk space can be achieved by using virtual machines (virtual storage facilities) on each host, using the local space of each host and present it as shared network storage device. However, most of these devices requires a minimum of 3 guests. You can run a shared on a single host storage devices, but you would still not any redundancy in the event of a host failure.

  André

• shared folders (host: windows server 2003, ubuntu reviews)

  Hi, I'm under VMware Player 3.0.1 on Windows server 2003.

  I built a WM with a host-only connection, and I'm under Ubuntu 2.6.28 on it.

  I want to just copy some date from the host to the host.

  I created a folder on the host (windows) and I checked it in the file sharing settings in the virtual machine settings.

  My problem is that I don't know where I can see this folder on my ubuntu (guest).

  Any idea?

  Thank you. Overview

  Shared VMware folder do not need a network connection.

  However, they are not necessary for a network connection, you can use the card AMD PCnet32 driver. But the VMware tools are highly recommended and necessary for shared VMware folder Option.

  Remember to switch to standard network shares.

  AWo

  VCP 3 & 4

  Author @ vmwire.net

  \[:o]===\[o:]

  = You want to have this ad as a ringtone on your mobile phone? =

  = Send 'Assignment' to 911 for only $999999,99! =

• WiFi - ethernet sharing does not work yet

  I have a MBP 2011. trying to share my wifi internet via an ethernet connection, but the * thing doesn't play ball! can't find any info, but keep looking... someone met / corrected this before?

  OS X Yosemite: share your Internet connection

• Files saved to merge "Shared folder ' between host Mac OS and virtual Mac OS not opening not.»

  Hello

  If I save a file in the folder "Shared" my host Mac OS machine merging, I can open it only on my host machine, but not inside my virtual machine to Mac OS.  In addition, it shows the incorrect file type in the virtual machine (just 'Document') not the actual file type.

  The reverse is also true, if I record a 'Shared' file of Fusion of in my virtual machine, I can open it only on my virtual machine, but not inside the host machine.  Again, it shows the incorrect file type in the real (just "Document") not the file type host machine.

  The files must be for the most part very well, because they will open in their own environment of the shared folder, but the Mac OS in the Middle against a reason any won't open them.  Suggestions?

  Thank you

  -Jeff

  Solved...  I just need to add 3-digit extensions of file names (for example, .jpg, .psd, etc.) that normally may not be needed in your own environment, but apparently are required when files are in a shared folder.

  -Jeff

• Storage shared between cluster hosts

  Hello

  I have a number of hosts managed under a VC server clusters. I want to downgrade the ESX 3.5 cluster and spend all my virtual machines to my vSphere cluster. I intend to move the storage currently used by ESX 3.5 clusters as well.

  Is this OK (or supported) or even possible for me to do the following?

  1. attach the storage used by the cluster cluster vSphere ESX 3.5 (so it is folded in TWO clusters).

  2. the servers from ESX3.5 to vSphere vMotion cluster cluster.

  3. turn off the cluster of ESX 3.5.

  I guess it boils down to two questions.

  1. can you be shared between host cluster storage two?

  2. If you can, is it possible to vMotion between cluster hosts, assuming that all the vMotion compatibility checks are successful?

  If the above is not possible, I'm guessing that a V2V of VMS ESX 3.5 would be the way to go, and I have to find new storage for the cluster of vSphere.

  Thank you

  G

  Hello

  If you have a SAN vSphere-taking in charge, so there is no problem.

  According to the CRA on your 3.5/vSphere ESX CPU hosts, you might have problems with storage vmotion/vmotion. One way would be to enable CVS, however requiring all virtual machines to be powered off.

  But present the LUN 3.5 4.x guests and make a svmotion is not a problem if you have taken care of storage. (www.vmware.com/go/hcl).

  Then you can just vmotion (if you do not have CPU incompatibility) virtual machines to new hosts, or stop and move.

  VCP3/VCP4/VSP/VTSP/MCTS: Virtualization

• Adapter Ethernet Thunderbolt has stopped working after update 10.11.2.

  Hello, after my update to 10.11.2 on my MacBook Pro retina 15 "mid-2015, my crush Ethernet Adapter has stopped working. It comes in the reporting system and it shows that it connected to ethernet, but in the network Panel, the State remains red and I don't get an IP address.

  My colleague who has a MacBook 2013 15 "retina Pro also has the same problem. We tried the retail adapters Ethernet Thunderbolt, but still no connection on one of our networks.

  Anyone else see this behavior?

  Same problem here on my end 2013. In Recovery Mode, the card works (good trick to know if hardware is broken). Roll back via Time Machine works 10.11.1 and adapter. Adapter and 10.11.2 relocation does not-MBP-R all my colleagues in different years work well after the update.

  BTW. : not only Thunderbolt Ethernet does not work, but the cards virtual Parallels (for shared and host-only) as well (only bridged mode works).

  So far, all the stuff has failed. And now I will notify again before the update.

• CompactDAQ via the virtual machine

  Hi all

  before I dive into the documentation, how can I a CompactDAQ ethernet to connect to a virtual machine?

  In other words, what kind of ethernet configuration is necessary?

  The device has a static address (on what subnet?).

  should I use DHCP (I need a DHCP server on my host?).

  I can run my guest in NAT or must it be closed?

  Or is the totally different protocol, non - IP based (in this case how do I pass it to a virtual machine?).

  Thank you

  OK, I'll answer my message because it may be useful to others.

  In the configuration of the VM, set two networks:

  -one such as a NAT device is bound to the network interface used to access the web. Here I use the host being Linux and there is wifi, wlan0

  -one as a BRIDGE is related to the ethernet jack connected to the CompactRIO

  Start the virtual computer and configure the ethernet connection 2nd to use DNS and no firewall. After installing NIDAQmx, restart and from MAX, the devices should begin to appear.

• NETWORKING AND SHARING FILES IN WINDOWS 7

  As stated, I am putting in place on my simple file sharing network. Previously, it was only between two Macintosh computers, a Windows 7 machine and storage machine. Now, I want to add another laptop and PC - both running Windows 7 - to the network and connect to the storage machine, until then known as 'the server '.

  The laptop connect through wi - fi. The PC and Macintosh computers connect via ethernet. They are all on the same network. This network uses WPA2-PSK security. The parameters of sharing on all Windows PCs, including the server include:

  NETWORK DISCOVERY: WE

  FILE & PRINTER SHARING: WE

  PUBLIC FOLDERS SHARING: WE

  MEDIA STREAMING: WE

  FILE SHARING CONNECTIONS: 40/56 BITS

  SHARING PROTECTED BY WORD: OFF

  HOMEGROUP: USE ACCOUNTS USERS & PASSWORDS

  The same settings apply to public networks.

  In addition, every single player in all Windows computers have the following parameters:

  ADVANCES OF SHARING: SHARE THIS FOLDER

  USERS OF LIMIT: 20

  PERMISSIONS: EVERYONE

  TOTAL CONTROL: ALLOW

  CHANGE: ALLOW

  READ: ALLOW

  SECURITY: ADMINISTRATORS, AUTHENTICATED USERS + USER + SYSTEM

  TOTAL CONTROL: ALLOW

  EDIT: ALLOWS

  READ & EXECUTE: ALLOW

  CONTENTS OF THE FOLDER: ENABLE

  READ: ALLOW

  SPECIAL PERMISSIONS: HIDDEN

  However, I am not able to see some readers on some of the computers or encounter errors like this:

  WINDOWS CANNOT ACCESS \\SERVER\G

  YOU ARE NOT ALLOWED ACCESS TO \\SERVER\G. PLEASE CONTACT YOUR NETWORK ADMINISTRATOR TO REQUEST ACCESS.

  
  When I click on "for more information, see Help and Support ', I am asked the following questions to which you will find listed answers:

  YOU HAVE NOT CREATED OR JOINED A WORKING GROUP
  I don't want to use the working groups.
  

  YOU DO NOT USE A HOMEGROUP, AND THE FOLDER OR PRINTER YOU'RE TRYING TO ACCESS HAS NOT BEEN SHARED
  I'm not interested by your nonsense whatever group, thank you.
  

  NETWORK DISCOVERY IS TURNED OFF
  No, it isn't.
  

  PASSWORD PROTECTED SHARING IS ENABLED
  No, it isn't!
  

  THE COMPUTERS ARE NOT IN THE SAME WORKGROUP
  They are not because I'm not interested in the use of working groups.
  

  YOUR COMPUTER DOES not UPDATE FOR YOUR ITINERARY R
  It's supposed to be a joke or some jerk programmer think actually it was useful to distance?

  In fact, when I try to create a homegroup of the server, I don't see is a 'Register' button and clicking on that joined a homegroup belonging to one of Windows laptops for a silly reason. There is NO setting to CREATE a homegroup. I am only able to join an existing homegroup.

  -------------------------------------------------------------------------------

  TL:DR

  All I want to do is freely share files between devices approved on my secure network. Gage rocket science, Microsoft introduced in Windows 7, I don't want no part of it.

  Where is the "DISABLE all BLOODY SECURITY AND SHARE THE GODDAMNED FILES"button in Windows 7?

  Hi Nicky,

  Apologize for the delay in response.

  We understand your frustration, but the problem you are having is more complex than what is generally answered in the Microsoft Community forums.

  I suggest you to post the same question on the TechNet forums, since we have a dedicated support and they will be able to answer the same.

  It will be useful.

• No route to host

  Hello

  I have an iMAC new with Mountain Lion 10.8.2 installed (all updates are installed to).

  I have VMWare Fusion 5.0.2. installed also.

  Now when I turn on VMWare Fusion my internet connection is not active in mountain lion.

  All that follows is perfectly configured:

  -Ethernet to the host computer is configured with DHCP with its own IP address.

  -Network card in the virtual machine is configured to be filled (to get its own IP address) and when I'm in the OS that is installed on the virtual machine the IP I'll be back is a diffirent one then the host operating system.

  -In the operating system installed on the virtual machine, I have internet connection!

  -Within the lion mountain with network tools I can't do a traceroute to what anyone outside the network.

  -I can close the VM or any computer within my local network of mountain lion.

  Could what I do to understand what is wrong with the OS - X or VMWare fusion 5 eighter mountain lion?

  Best regards

  Richard

  The main problem seems to be networks virtual for 'host-only', 'NAT' and 'shared '.

  These 3 virtual networks, there are 3 ethernet adapters added to your Mac OS X.

  By default, only 2 not 3 virtual networks are created by VMware Fusion, VMnet1 (host-only or private on my Mac) and VMnet8 (NAT or share with my Mac).  The "add_bridge_mapping en0 2" is not a default value and is created if a user chooses to link the bridge to a specific host NIC

  Yes where it should not.

  Stop VMWare Fusion and restart.

  With the following command in the terminal, you'll see that the en0 ethernet adapter:

  ifconfig

  Now the startup of the host operating system and voila, it should work.

  Please keep in mind that it would be you may have to repeat these steps once change you settings of network through the graphical interface of VMWare.

  Because it is a configuration file and it can be changed again by VMWare Fusion.

  I have not tested it since its now works for me.

  Deleting VMnet1 and VMnet8 host and not have them available for the guest are fine if you must never use Bridged Networking however is not always practical while of particular workaround may have helped isn't you necessarily the answer for others have an Internet/network connectivity issues!

  In addition to manually edit configuration files of VMware Fusion, that it must be done with the Virtual Machines stop, not suspended, and VMware Fusion closed... then your efforts are not in the proper context!

• UDP communication via secondary ethernet port on the cRIO-9074 problem.

  Hi guys.

  I connected my host pc running LV 2010 my cRIO-9074 port using a main ethernet crossover cable. I want to use the second port ethernet on the cRIO-9074 to read UDP messages, and I want to access these messages on my host. UDP messages are sent from a local network, but for testing I also use a second pc running LV 2010 to send UDP messages.

  I configured the ethernet on the cRIO-9074 ports according to this tutorial: "knowledge base 4E0DGASK: Configure the Ports of double Ethernet on real-time controllers'." " My host and primary ethernet port belong to 'Subnet A' while the second port and the second computer, sending UDP messages belong to 'Subnet B' (at the end of my post I will list the masks of ip addresses and the subnet).

  For simplicity, I used the VI´s of this example as a basis for UDP communication. The "UDPServerOnRemoteTarget.vi", which broadcast messages UDP, will run on the secondary computer. The "UDPClientOnRemoteTarget.vi", which reads messages UDP, will work on my host pc.

  Now, in the 'UDPServerOnRemoteTarget' VI, you must specify two IP addresses (port # remained unchanged at 3363):

  1: the IP address of the ethernet port that will be broadcast UDP messages.

  2: the IP address of the ethernet port that will receive the messages.

  In the #1 case I put the IP address to the IP address of the ethernet on the secondary pc port.

  At the #2 I tried to set the intellectual property: a) IP address of the secondary ethernet port on the cRIO, b) IP address of the ethernet on my host computer port and c) IP address of the primary ethernet port on the cRIO.

  None of the parameters produced results. I also tried to change the port number, which did not help.

  However, if I bypass the cRIO and connect the host pc and the secondary computer directly (by using a cable crossed a regular cat5 ethernet cable), I am able to send and receive UDP messages (the two stand-alone always are on different subnets). I guess that this at least excludes any fault in the VI´s code.

  Does anyone know what I'm doing wrong here? Is it possible at all to read the UDP messages that are sent to the secondary ethernet port on the cRIO my host pc?

  I have searched the entire site OR and forums, but didn't come through all that solved my problem. Most of the other tutorials configuration resembling my case is to import the device sends UDP messages in the project, but which is clearly not possible in my case, or is it?

  My IP settings are:

  cRIO 9074:

  Primary ethernet port: 169.254.62.215

  Secondary ethernet port: 192.168.0.102 (static)

  Host PC: 169.254.58.4

  Secondary PC: 192.168.0.144 (static)

  SubnetMask on all ports are the value 255.255.0.0

  I hope someone out there can help me out.

  Kind regards

  Phat

  Solved.

  Stupid mistake. I was running the VI on the host instead of the cRIO pc, which explains why direct communication between the computers worked. Everything works well when it is compiled for the cRIO.

  Kind regards

  Phat

• Shared variable of subjects with the executable in real-time

  We have a PXi target running Labview time real 8.5 and we use a series of shared variables for communication between the target and the client software. The code was developed (and used) in the last 2 years, and presented no problems with the shared variables when they are deployed since the Project Explorer (for the target and the laptop based client software). However, when you try to run an executable version on the system time PXI real target of exactly the same engine code variable shared seems to fail during the initial loading. Since it is an executable, it is difficult to display errors, but it seems that the accident occurred at the beginning of the program when we try to initialize a number of shared variables. Sometimes it loads but probably only 10% of the time. When you plug the tool to debug for code and restarting the executable, runs without any problem. However, once we managed to capture and error (error-1950678982 the shared variable client side read buffer is full).

  I checked a number of messages in the Knowledge Base (e.g. how to deploy Variables of a compiled executable shared network?), but it still has not solved the problem. Thoughts and suggestions?

  Adrian

  I tested it for a few hours now and I can't make it fail again. The big difference in my implementation was to use your suggestion, and no wire the error cluster through the method since the error it generates caused a number of questions later. So let me summarize the final configuration that seems to work then:

  -during the execution and executable on a target time real 8.5, startup not connected to a client. Library of shared variable hosted on the target and should load by itself.

  -J' added a flat structure sequence on the vi 'main' (top of page vi executable) with a node (as shown above) Invoke method in the first structure with a timer to 10 seconds and the rest of the code in the second part of the structure. The shared variable library has been copied to the target in a data directory and the path provided to the method (the same way as above) and the IP address is that of the target.

  I discovered that it takes about 8-9 seconds for the shared variable engine and library to start (I don't remember is that past exactly that) and it is important to wait this time to initialize shared variables or the behavior is unpredictable. The method always generates the error 1043 (function not supported) but I simply ignore it now, and it seems to work.

  Thanks for your help! I will let you know if there is some instability in the future, but everything looks good from here.