Computer doesn't boot after updates

Similar Questions

• Problem re boot after updates.

  Hi, I have a laptop HP DV6, which is about 2 months old. He originally had Vista but I bought the cause 7 upgrde, I couldn't wait any longer for the free update, I want to come. Anyway, whenever windows needs to re start after updates to the computer does not start upward. When he tries, I see the HP screen at the first start and then nothing, just a blank screen. The power light comes on but the hard drive light doesn't work. I pressed the power button to turn off and turn back on and everything's fine. He started using Vista. I did a full restore before installing the 7 upgrade, but it always does. Any ideas?

  Check in safe mode if the same thing happens.
  To enter the safe mode press F8 when you restart.

  Try to start mode minimum troubleshooting:
  http://support.Microsoft.com/kb/929135

  Make sure that all drivers are up-to-date.

  Repair the installation of Windows 7:
  http://www.SevenForums.com/tutorials/3413-repair-install.html

  All the best!

• Mailto doesn't work after updating FF 42.0

  Mailto doesn't work after my last update. The entrance of mailto is not under Tools > Applications and there is no drop-down list to add an entry. My default e-mail program is Windows Live mail.

  Hmm, mailto certainly should not be missed.

  Sometimes, the file that stores these actions of the Manager/download application is damaged. As it is difficult to change, when there is a problem, we offer usually when you rename the file and allows Firefox to rebuild the Windows registry. Who cannot help if mailto is missing from the registry, but I think it's worth a try:

  Open the settings folder (AKA Firefox profile) current Firefox help

  • button "3-bar" menu > "?" button > troubleshooting information
  • (menu bar) Help > troubleshooting information
  • type or paste everything: in the address bar and press Enter

  In the first table of the page, click on the view file"" button. This should launch a new window that lists the various files and folders in Windows Explorer.

  Leave this window open, switch back to Firefox and output, either:

  • "3-bar" menu button > button "power".
  • (menu bar) File > Exit

  Break while Firefox finishing his cleaning, then rename the mimeTypes.rdf to mimeTypes.old (or another name of your choice, in the case where you decide to roll back this experience).

  Launch Firefox back up again and return to the Options page to specify your preference. Mailto appears once more?

• Cutmaster plugin doesn´t works after update to Illustrator CC 2015

  Hi, someone at - he saw the problem with the plugin Graphtech´s Cutmaster after update to Illustrator CC June 16, 2015 2015

  Any solution, anyone?

  I hope ;-)

  / Patrik Liedgren

  If it worked in CC2014, then fall back to this version. For a plugin update, contact Graphtech.

• FaceTime doesn't work after update of the sierra

  After the transition to macOS Sierra 10.12, Facetime does not accept my id to icloud and pass. "an error occurred during activation. Try again. '  Been trying for 3 days to activate it now.

  My ID Apple and the password work everywhere else but not in facetime.

  My mac is:

  MacBook Pro (15 inch, early 2011)

  Intel Core i7 2.2 GHz

  8 GB at 1333 MHz DDR3

  AMD Radeon HD 6750 M 1024 MB

  Intel HD Graphics 3000 512 MB

  256 GB SSD (OCZ-VERTEX4)

  Series Nmumber: C0 * RJD

  < personal information under the direction of the host >

  Hello

  Safe Mode boot removes the system caches that can help after an update or upgrade.

  Follow these steps to start in safe mode.

  1. Start or restart your Mac.
  2. As soon as you hear the startup tone, hold down the SHIFT key.
  3. Release the SHIFT key when you see the logo Apple appears on the screen.

  After the Apple logo appears, this may take longer than usual to reach the login screen or your office. This is because your Mac performs a check of directory of your drive to boot in safe mode.

  To leave safe mode, restart your computer without pressing any keys during startup.

  Then try FaceTime.

• Computer fails to boot after installing SP1

  I use Vista without SP1 for quite awhile. I've just updated to SP1 since the message kept popping on my screen. Now the computer will not book. I used the original vista bootable CD and clicked on repair. He began the process of repair, but got stuck at the same registry error

  !!! 0xc01a001d! 35032/165955 (\Registry\Machine\COMPONENTS\DerivedDat...)

  Thus, even the repair doesn't seem to work

  I need to fix this since I have a lot of important files on my hard drive.

  Support for Vista Gold (no Service Pack) ended on Tuesday, April 13, 2010. If you get only to try to install SP1 (and it is NOT yet installed), ALSO lack you the value of six months of critical security updates. Therefore, it is almost 99.9% certainty that you see the effects of a long infection date hijackware.

  See...

  Cleaning a compromised system
       http://TechNet.Microsoft.com/en-us/library/cc700813.aspx

  Personal data backup (which none should be considered 100% reliable at this point) then format the HARD disk and do a clean install of Windows. Please note that a repair installation (upgrade AKA on-site) will NOT fix it!

  HOW to do a clean install of Vista: section "If you want to reinstall Windows Vista by running a new installation...". "of http://windows.microsoft.com/en-us/windows-vista/Installing-and-reinstalling-Windows-Vista

  NOTE: If your computer came with a set of disks, there is a hidden partition restore (not to be confused with the restoration of the system) you would use to do the clean install (AKA a "destructive recovery").

  After the new installation, you will have the equivalent of a "new computer" in order to take care of EVERYTHING on the next page before connecting the machine to the internet or one local network (i.e. other computers) AND BEFORE to plug in a flash, SD card, or any other external drive to the computer otherwise:

  4 steps to help protect your new computer before going online
       http://www.Microsoft.com/security/pypc.aspx

  Tip: After completing the computer fully patched, download/install KB971029 manually before connecting any player external to the computer: http://support.microsoft.com/kb/971029

  VERY IMPORTANT! -Online any Norton or McAfee free trial which is preinstalled on the computer when you bought will be reinstalled (but invalid) when Windows is reinstalled. You MUST uninstall the trial for free AND download/run the removal tool appropriate prior to installing the updates, Windows Service Packs or IE upgrades AND BEFORE installing your new anti-virus application.

  Norton Removal Tool
       FTP://ftp.Symantec.com/public/english_us_canada/removal_tools/Norton_Removal_Tool.exe

  McAfee Consumer product removal tool
       http://download.McAfee.com/Products/Licensed/cust_support_patches/MCPR.exe

  See also:

  Risks & benefits of P2P file sharing
  http://www.Microsoft.com/protect/data/downloadfileshare/filesharing.aspx
  http://blogs.technet.com/MMPC/archive/2008/10/06/the-cost-of-free-software.aspx
  http://www.us-cert.gov/CAs/tips/ST05-007.html

  Measures to help prevent spyware
  http://www.Microsoft.com/security/spyware/prevent.aspx

  Measures to help prevent computer worms
  http://www.Microsoft.com/security/worms/prevent.aspx

  Avoid fake security software!
  http://www.Microsoft.com/security/antivirus/rogue.aspx

  If you need additional assistance with the clean install, please start a new thread in this forum: http://social.answers.microsoft.com/Forums/en-US/vistarepair/threads

  If these procedures look too complex - and there is no shame in admitting this isn't your cup of tea - take the machine to a local, good reputation and stand-alone computer (that is, not BigBoxStoreUSA or Geek Squad) repair facility.

  Good luck!

  ~ Robear Dyer (PA Bear) ~ MS MVP (that is to say, mail, security, Windows & Update Services) since 2002 ~ WARNING: MS MVPs represent or work for Microsoft

• Windows Vista fails to boot after updates combined with Mcafee instalation.

  The laptop is a 2007 medion mim2330 running 32 bit vista Basic.  He was protected by Bullguard, but it had expired and has been exceeded. A message appeared on the screen WARNING french that he had been infected by a virus - it does not look official and I am not sure that he clicked on the option to download solution - however the phone still worked. I had a Mcafee 3 user license and wanted to install it so I uninstalled bullguard and installed Mcafee process windows crashed and failed to WINDOWS START SCREEN appeared and I was unable to boot windown in any mode. I gave the phone to a knowledgeable friend who said it was a virus, but did not know that one - he said, it has been deleted, all hardware tests had been run and it was perfect. It has resized the partition of disk doing a great score including a remains a very small. He reloaded windows with avast antivirus and gave the laptop back to work. I wanted to use the Mcafee I had paid for, so I uninstalled avast and installed Mcafee. Everything went well and the laptop worked - however the mcafee warning sign came up saying scan in real time has been disabled - he turned back, but a few minutes it turned off again. I have contacted Mcafee used virtual tech then chatted in their eng who suspected a virus, a virus scanner from mcafee, rather than the laptop - it was very good. While the computer restarts windows laptop crashed and the WINDOWS FAILED to START SCREEN has appeared. I gave it back to my friend who reloaded windows and avast and widely used for a week. When we got it back avast had been removed and there was Windows Defender - didn't light alarm does not. We loaded on Mcafee and had plenty of updates (and hours) then tried windows live messenger telling to SP1 and SP2 are necessary. They were charged after an eternity using automatic updates of windows. After everything has been loaded on a final restart gave place WINDOWS failed to START screen and does not start in any mode. I thought it might be linked to the abduction of an antivirus and the installation of another, so I put in the original Windows restore disc in and formatted the large partition, then reloaded windows and all its drivers then went on updates auto and auto updates for 24 hours until what he said to date. Installed mcafee - no problem, then tried windows live essentials that required sp1 and SP2 - used auto updates to download SP1. When this is completed there were two messages from Mcafee saying restart the pc and the other problem Center and soln windows saying an upate problem was found to go online to find the solution, I checked windows update history and SP1 and all other updates were installed successfully, so I rebooted the laptop - at which point it crashed and WINDOWS has no PU START APPEARED to-it wont start in any mode. Suggestions as to the cause and or how to make the process of restoration in less time - much appreciated. We have a same laptop bought at the same time, running the same original software and Mcafee - never a single problem. Thank you very much

  Usually, this means that Windows could not load the packages of metadata for some devices on your computer. If you do not already have it, you can run chkdsk/r (there is a space between thek and /) to verify the integrity of your hard drive. Follow the steps below:

  1. reboot your computer

  2. immediately press theF8 key until you reach the Advanced Boot Options menu

  3. Select Safe Mode with command prompt.

  4. at the command prompt, typechkdsk/r

  Dena
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

• Why my iPad doesn't load after update to iOS10?

  My iPad anti-aircraft battery charged fine this morning until what I've updated my IOS 10 software. Is there a solution to this?

  Hello. You use Apple original charger and cable? It seems to be problems with other configurations, see iPad is cooler computer after an update to iOS 10.

• Windows 7 boot after update loop

  This afternoon, I ran windows update and it said to restart my computer.

  Reboot it starts normally and then when it gets to the page where I normally connect it says: "Please wait" then flashes to the 'preparation set up windows. Do not turn off your computer. "And then it restarts and does the same thing over and over again

  It does the same thing when I try to run safe mode, so I can't run that.

  "Startup Repair" does with anything

  He claims that I have no restore points, (which i cannot believe since I have them never deleted).

  Memory diagnostic Windows did not come with anything either.

  Any ideas?

  Hello

  If you have the Windows 7 DVD, you can try to boot from the DVD startup repair and check uf that helps. Follow the link for more information.

  http://Windows.Microsoft.com/en-us/Windows7/what-are-the-system-recovery-options-in-Windows-7

  http://Windows.Microsoft.com/en-us/Windows7/Startup-Repair-frequently-asked-questions

  Hope this information is useful.

  Amrita M

  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

• computer does not start after update

  what computer starts without updates without problems.
  When the computer starts after a update it does not start and goes into the Startup Repair. after repair, I check: diagnosis and repair of the details:
  the root cause of watch - start criticalfile c:\ntoskrnl.exe is corrupt. with a 0xa error code

  can I fix it myself?

  horticulturist,
  Did you run the System File Checker?  If so, what were the results?  If you haven't done so already, you will need to run (sfc/scannow) so that it can check your system files for all questions.  Also this happens after any update is installed, or only the current links that are pending?  I suggest try to install an update at a time and see if you are able to get the updates installed or not.

  Mike - Engineer Support Microsoft Answers
  Visit our Microsoft answers feedback Forum and let us know what you think.

• computer won't reboot after updates missing or corrupt ntoskrl.exe

  I have a HP pavillion laptop - I have upgraded to Vista Business (so I than the cd) the computer failed to install service pack 1 for ever. He kept getting an error which is ambiguous in the research. However, one day last week he decided that it would update on its own. After the update I get a message that indicates that the ntoskrl.exe file is missing or damaged. The machine does not start without failure or other mode. I got started with the disc once. I thought that the problem has been corrected - and then I restarted the computer a few days later and it happened again. I succumbed to get it to load all the. It is said that it can not be solved. The only time where this morning, I had to complete the restore of the system, the machine has restarted and began its count of files (I think that some 97000 files + as the update of windows) and loop to the same error message. I got to a command prompt and looking for help on what to do next. Thanks in advance for your help. In addition, because I bought the Vista upgrade separately - do any free support from MS? If so - where should I call? Thanks again.

  Hi Upinthenight,

  Thank you for using the Microsoft Vista answers Forum.

  You can follow the steps mentioned below and let us know if it works:

  1. put the Windows Vista installation disc in the disc drive, and then start the computer.

  2. press a key when you are prompted.

  3. Select a language, a time, a currency, a keyboard or an input method, and then click Next.

  4. click on repair your computer.

  5. click on the operating system that you want to repair, and then click Next.

  6. in the System Recovery Options dialog box, click command prompt.

  7. once we are on the command line, type Bootrec.exe /fixboot, and then press ENTER.

  Go to your second question on the support options for Windows Vista; Phone/Chat for Windows Vista support is paid but the free support for Windows Vista Service Pack 2 (SP2) is valid until November 26, 2009.

  Thank you and best regards,
  Abdelouahab

• Computer doesn't recognize not update Service Pack 1

  Original title: you read these questions? the responses I've read so far say NO

  The question I ask has been requested several times, but the responses I've seen do not address the issue, just to give instructions on how to install SP1, but not how to fix the problem by heart.  SP1 has been installed on several occasions:

  10 times with success since 14/07/2015 through today 06 19, 2015, [update history] and the computer does not recognize always day and it says I need.  It's why I can't do SP2 either.  The computer properties does not mention MS

  Last year, I called and the technology did and the same results.  Please answer this question!   Thank you

  The question I ask has been requested several times, but the answers I've seen do not address the issue, just to give instructions by heart on how to install SP1, but not how to fix the problem.  SP1 has been installed on several occasions:

  10 times with success since 14/07/2015 through today 06 19, 2015, [update history] and the computer does not recognize always day and it says I need.  It's why I can't do SP2 either.  The computer properties does not mention MS

  Last year, I called and the technology did and the same results.  Please answer this question!   Thank you

  Hello

  We read the questions and try to give solutions to the best of our ability, depending on the quality of the information you provide on the problem.

  We do not work for Microsoft.

  We are mainly volunteers here, just like you, computer users who give free advice from other users in our own spare time.

  @@@@@@@@@@@@@@@@@@@@@@@@@@

  Unless you have the SP1 and SP2 installed, there is no support for Vista; Microsoft support ended.

  You say that you do not have SP1 installed, then of course we give you instructions on how to install it.

  And when you post here complain about anything doesn't work for you, publish a list of the things you have already tried.

  It is not installed if it does not appear under properties

  Click Start > right click on computer > left click on properties > see if you have Vista 32 bit or Vista 64-bit installed.

  It will also tell you which SP you have installed (apparently without SP).

  Then, choose the download of 'bit' OK to use to install Service Packs, installation of SP1 first if it is not already installed.

  Vista SP1 32-bit (x 86): http://www.microsoft.com/en-us/download/details.aspx?id=30

  Vista SP1 64-bit: http://www.microsoft.com/en-us/download/details.aspx?id=21299

  Vista SP2 32-bit (x 86): http://www.microsoft.com/en-us/download/details.aspx?id=16468

  Vista SP2 64-bit: http://www.microsoft.com/en-us/download/details.aspx?id=17669

  This Information Microsoft can help you resolve problems that you encounter during the installation of Service Packs for Vista.

  http://support.Microsoft.com/kb/947366

  See you soon.

• PXE - E53: no boot after update from Dell file

  In recent weeks, I have a new inspiron 5999. yesterday, there was an update from dell and the computer restarted I had a black with screen

  Intel UNDI, PXE - 2.1 (build 083) Copyright (C) 1997-2000 Intel Corporation
  This product is covered 459 by one or more of the following patentsL US5, 307, US5, 434, 872, US5, 732, 094, US6, 570, 884, US6, 115, 776 and US6, 327, 625
  ADR MAC CLIENT: 18 03 73 11 F9 00 GUID 44454C4C-4700-1034-8035-B8C04F4E5131 PXE - E53: no boot file name given
  PXE - M0F: Exit PXE ROM.
  Reboot and select proper boot device
   
  What should I do now and what should I do to avoid this problem in the future?

  Go to the startup F2, boot sequence option, select UEFI, apply, exit and should start normally. I got this Dell and it worked for me. Good luck to both of you!

• No boot after update Win 7 64 bit (April 2016)

  In Windows updates in the Control Panel, I had chosen "check for updates but let me choose whether to download and install them, which seems to mean Don't warn me. Anyway, last week, I downloaded and installed a bunch of updates that went well and then after reboot there was 2 updates more so I downloaded / installed those, rebooted and now it gets as far as showing a tiny Preview windows startup logo and then goes to a screen offering the "(recommended) launch Startup Repair' or 'Start Windows normally'. The first ride in the screenshots shown:

  

  

  

  

  

  Any ideas how to recover it would be much appreciated please.

  There was some wild issues with this update

  https://support.Microsoft.com/en-us/KB/3133977

  https://Rog.ASUS.com/Forum/showthread.php?84441-Windows-7-Pro-UEFI-install-secure-boot-violation-ASUS-Maximus-VII-Ranger

  Do not know how your windows is installed but disabling secure boot and switching OS Type for other OS or see improvements

  Then enter your bios

  Go to Advanced Options / Boot and see what options are listed with CSM

  The CSM see if if only pass to legacy or UEFI could only help.

• OptiPlex 990 not PXE boot after update Bios A18

  After the update to A18 on multiple machines, I noticed that they all hang after address DHCP is affected and what would normally be the menu timer (if it was not all work in progress) or launch from the boot of automation.

  I also noticed when you update to the latest version on our Latitude E6420s so.  Returning to the A17 on the 990 and the 6420 corrects this problem.

  Is anyone else having this problem, and this Signals to Dell.  I tried to Google this but any how, I wrote the search I can't find anything with recent BIOS.

  Hello Irios103,

  It is difficult to determine what is causing the conflict with Bios version A18 and your systems. The improvements to the code may be the cause of problems on Cisco switches or oldest feature, such as the tree covering weight or the characteristic power of conservation.  You can also make sure the quick port is enabled.
  If you do not need specific to this version of Bios patches, it may be better to not use it.

  Improvements & fixes for version Watch:
  1 address system does not meet the keyboard intermittently.
  2. address UEFI OS fail boot with this disk number HARD password.
  3. questions of CCTK.
  4. improve the compatibility of PCI devices and USB devices.
  5 Update Microcode Intel SandyBridge processor.
  6 update Intel PXE ROM.

  I hope this helps.  Please let us know if you need further assistance or more information.
  ~ Maureen
  #iwork4dell