Computer stopped recognizing the scanner.

Similar Questions

• My computer has stopped recognizing the HP7450 printer, although showing the connection to the USB "ready".

  My computer has stopped recognizing the printer plugged in usb port

  Hello

  ·        You are able to print a test page for your printer?

  You can try the suggestion given in the article below and check if that helps get the printer to work.

  http://support.Microsoft.com/kb/308028

  Hope this information is useful.

  Amrita M

  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

• update my laptop stop recognizing the driver of Bus controller universal external hard drive.

  Recently my laptop stop recognizing the external hard drive. It was working fine before. The MFG. external IOMEGA Hardrive said universal Bus controller driver to be upgraded. It is Intel (R) 82801DB/DBM USB 2.0 Enhanced Controller pipe - 24CD. My several attempts to install an automatic update of the driver from the Intel Web site has failed.  What to do next?

  Hello

  1. which is the version of the service pack installed on the computer?

  2 have you made any changes to the computer before the show?

  3. What is the exact error message?

   
   
  I suggest you perform the steps described in the document:
   
   
  How to get and install the USB 2.0 drivers in Windows XP Service Pack 1
  http://support.Microsoft.com/kb/329632
   
   
   
  I hope this helps.

• computer cannot detect the scanner or camera

  When I plug in my digital camera Canon for my xp, then turn it on, I hear a small beep, then nothing. When I go into the Panel, printers and other equipment, scanners and cameras, I see 2 points. 1 is, WIA Canon MX310 SER. The 2nd one is Canon PowerShot SD1300IS. I then click on the Canon PowerShot SD1300IS and then get pictures, but nothing happens. The cameras screen display turns off, but that's all. It seems to be connected to the computer, but not to download pictures.

  When I keep trying I sometimes get an error message, the computer cannot detect the scanner or camera.

  How can I solve this problem and download my photos?

  Thank you Tim

  Hey volunteer J;

  Thanks for the help, but it did not help.

  I found the answer on page 2 of microsoft answers, xp, images and videos.

  6 questions down, how to re install microsoft scanner and Camera Wizard.

  It turns out that some tech volunteer known as J (is it you?} came across the solution to my problem on this site:http://www.veiled-chameleon.com/weblog/archives/000231.html )

  I have used PC Cleaner on this xp, and I think he may have disabled some of the registry keys. For me, I had to start my pitcher of DCOM Server, RPC, Remote procedure Call Locator process and put them on automatic. Once I rebooted, everything works great.

  I'm so happy that tech Volunteer J, done everything search last December. I bet it helped a ton out of veterans with our cameras. How did he find veiled Chameleon? Wow he must be smart enough.

  Thank you for volunteering j. (is it you?)

  Thank you Tim

• I have a HP printer and computer wont recognize the scanner

  The component scanner of the printer which is the custom scanner to connect to the computer. The computer does not recognize the scanner

  Most often when a device does not work, it is because the driver is damaged. Re-install a new copy should help

  Remove the driver current completely and install the latest driver available.  For instructions on how to do read everything to update the drivers of my partner JMH3143 http://answers.microsoft.com/en-us/windows/wiki/windows_other-hardware/updating-a-driver/a5e6345e-af9b-4099-bef0-8d22254aa1c1?tm=1436753520149 here

  http://Windows.Microsoft.com/en-us/Windows7/update-a-driver-for-hardware-that-isn ' t-work correctly? SignedIn = 1

• HP 3050 j610 not recognizing the scanner or scan

  pls help. I instaled and reinstaled it makes me sick. .. I can print without problem.  but it will not scan.  Since a scanner, it says I have error to go to the computer.  to the computer it just does nothing. .. ive never had a problem like this before... thks gazzoomom

  Hi Gazzoomom,

  ·         What operating system is installed on your computer?

  ·         What is the exact error message?

  ·         Did you do changes on the computer before the show?

  Please refer to the below mentioned articles and check if the steps help you solve this problem:

  The problems of scanning

  http://Windows.Microsoft.com/en-us/Windows-Vista/Troubleshoot-scanning-problems

   

  Printer in Windows problems

  http://Windows.Microsoft.com/en-us/Windows/help/printer-problems-in-Windows

  Hope this information helps.

• After updating Windows computer stops at the configuration in step 3 of 3, 93% - HELP

  After installation of Windows from one day to the next update, my computer will configure the update.  It stops at the step 3 of 3, 93%, stops, goes to the top.  The same appears configuration step 3 of 3 screen, 93% and stops.  What can I do?  Thank you

  Hello Imaco,
  Thank you for visiting the Microsoft Answers forum.
  When the computer boots press F8 until you see the Startup Options and select last known good configuration.

  Thanks, Martin
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think

• Computer stops when the wireless switch is turned on

  I have a Toshiba Satellite M-35 S456 with Windows XP Home Edition.  When I turn on the switch on the bottom of my laptop wireless, the screen flashes blue with a message and then stops.  The computer tries to restart, but during the process of the blue screen flashes again and it stops.  If I switch the switch wireless to the computer will restart.  I am trying to connect to the internet via a router which is already set up and running.  All solutions?

  Hi MartinLaMarr,

  ·         What is the Blue error screen that you are talking about?

  ·         If so, have you noticed the blue screen error message?

  Check to see if the following is useful.

  Method 1: Unplug non-essential devices from the computer and restart the computer.

  Method 2: Try to select disable automatic system failure reboot since the options of start menu advanced to know the Blue error screen.

  a. restart your computer and start pressing F8 on your keyboard. On a computer that is configured to start to multiple operating systems, you can press the F8 key when the Boot Menu appears.

  b. use the arrows to choose to turn off the automatic restart in the event of system failure in the Advanced Options of Windows Start Menu and press ENTER.

  Method 3: Updated with the latest wireless drivers and other drivers of devices from the portable computer. Log in the Web of Toshiba site to do.

  Content Page Model - Toshiba Satellite M-35 S456

• computer not recognizing the cd/dvd.

  MY HP computer do not recognize cd/dvd = when I go to Device Manager and double-click Properties it says Error loading driver (error code 19)-
  I have windows vista home edition/i tried to go to the Device Manager and on some suggestionn those of the United Nations since the CDROM
  then re booted.
  It shows in Device Manager - but always watch - sign and sign - yellow
  without change and the same message as above
  Help, please

  Hello
   
  1. have you made changes on the computer recently?
   
  The unit will not work properly if the driver is damaged or can not load the Windows generic driver. To resolve this problem, try running Microsoft Fixez_ the. Visit the following link to download the fix it: http://support.microsoft.com/gp/hardware_device_problems
   
  You can also run this fix if the still lingering question and check the result: http://support.microsoft.com/kb/314060
   
  If the problem persists, then please contact the manufacturer of the system for more support.
  http://h20000.www2.hp.com/bizsupport/TechSupport/ContactHP.jsp?
   
  I hope this helps.
   
  Kind regards
  Syed
  Answers from Microsoft supports the engineer.

• Computer stops when the power to the computer to sleep, on computer virus problem

  Hello

  When I put my pc sleep and wake him up, a window pops up saying that the machine has stopped unexpectedly, and then the pc automatically reboots by itself,.

  after reboot, a window box comes in saying that the pc rebooted one... and that Windows will inform me what to do.  What happened yesterday and today.

  I must say however that Friday evening, August 24, my pc was slow work, since a few days I noticed, but Friday it was slower, I could see that something

  moving in often via the little blue wheel icon that shows that something is happening.

  I "had" McAfee Total Protection in my machine since 08/05/2012 and last night I clicked on the McAfee to do a full Scan of my pc, because I thought there was something fishy in it.  McAfee Full Scan clicked, a blue page with white letters arrived, quick and deep that I saw Dump numbers going up to 100, then the blue screen came out and restarted my PC.  After reboot a small box of Windows came to say that the machine had stop unexpectedly, he

  has run a control bar, when in fact something like 'your stop machine unexpectedly and windows will inform you what to do', something like that.  I then

  new click the McAfee icon, click the full sweep, the same thing happens again anywhere.

  Then, I went to the website of McAfee and talkative with Technical Support, he came into my pc to see for himself, he opened the Navigation button and had IP

  address to which McAfee was 'downtime '.  He told me I had a virus in my computer... He gave me a phone # to call for assistance in the removal of the virus. I called, the man

  did not come into my PC to see, he said, I had to pay $89. something taken him. I closed with him, went with the customer, aksed for my refund...

  sad situation, but I withdrew my PC with McAfee.

  I've downloaded Malwarebytes, checked my PC had 2 Trojan horses, you click on Remove to remove the.  Still had Malwarebytes in pc, I went to Trend Micro, which I had before in my pc for years and renewed my Sub. with them and has installed. After doing a full Scan, no virus.

  I made a 'machine checking if' work properly AM early this morning.

  This afternoon, August 25. I opened my pc, the audit began, time + after pc restarted normally, then all of a sudden the blue window came with white letters, dump numbers went up to 100 then pc rebooted, Windows little box came "... unexpected" and normal ran pc after.  Worked a bit on the pc then place to sleep so I could go somewhere, when I clicked on the mouse to wake up, as I always do in the pc, it awakened, blue page with while that the lettering came, took place on the same things as above.  PC ran good, had to go eat, put the pc to sleep, came back same thing occurred again

  I searched what happens and found nothing.  I went to the community, there nothing either.  So I'm here today to help hoping that you know what is happening.

  Thank you for your time and your help.

  Bebb

  Hello

  Currently, you have a program full-time antivirus installed on the computer?

  If you do not have one, I suggest you to install Microsoft Security Essentials.  Follow this link to download.
  http://Windows.Microsoft.com/en-us/Windows/products/security-essentials

  Follow these methods.

  Method 1: Run a Scanner online from Microsoft.

  http://www.Microsoft.com/security/scanner/en-us/default.aspx
  Note: The Microsoft Safety Scanner ends 10 days after being downloaded. To restart a scan with the latest definitions of anti-malware, download and run the Microsoft Safety Scanner again.
  The data files that are infected must be cleaned only by removing the file completely, which means that there is a risk of data loss.

   

  Method 2: To remove the virus manually, see the article:

  How to remove a computer virus?
  http://Windows.Microsoft.com/en-us/Windows7/how-do-I-remove-a-computer-virus

  Important: The Troubleshooting Manual in the link above steps show you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base:

  http://Windows.Microsoft.com/en-us/Windows7/back-up-the-registry

• How to scan a document to my computer from my computer instead of the scanner itself?

  I tried the real scanner scanning and it says "Scanning error Scan of the computer" but how do I do this? I don't know how and I need to scan this document to my computer as soon as POSSIBLE!

  Read this and apply it to any model you have:
  http://h30434.www3.HP.com/T5/scanning-faxing-and-copying/HP-Photosmart-D110-scan-error/TD-p/370037

• Computer not recognize the scanner

  My computer suddenly (after several years) only is not recognize my scanner even if I reinstalled several times.  The Solutions Center is also not recognize it or my new printer

  Great, if you have any other questions let me know!

• Computer stops after the installation of security update KB2393802

  I'm 'rebuild' an old computer Gateway E-4600, to give via a local social agency.

  OS is XP Home, and the product ID of the COA is valid.

  I'm writing this, I'm in the middle of the 3rd attempt to get all of the updates to install * without * preventing the closure of the computer.  Each facility has given me minor differences in available updates, but I was not sufficiently detailed records of what was suggested to be more precise in these differences.    I'll know better here on out!   Laughing out loud

  I didn't know that a problem existed in the judgment until I was almost done with the first reconstruction, which included the installation of the software.

  During the reconstructions of the second and third, I largely used the system restore to isolate any problem and found the following:

  KB 2393802 for Windows security update prevents the computer from closing with the closure of the XP Start Menu or Task Manager.  The only way I found to stop it is to hold the power button on or unplug the computer.  I don't actually unplug the unit, but that obviously has to work!   Laughing out loud

  More interesting still, the article refers to Intel and AMD graphics cards, and this computer has a graphics card from NVIDIA GeForce2 MX/MX 400 (via Belarc Advisor).

  I'm still trying to find an answer online, but nothing so far.

  I can't give this with this problem :-(

  I would like to know the answer to one or both of the following questions:

  1. Why Windows/Microsoft Update tells me to install an update for a graphics card that is not installed in the computer?
  2. How can I prevent Windows/Microsoft Update listing and want to install the update that is as a manual or automatic installation install?

  Thoughts and suggestions?

  Yes, I'm still 'watching' this thread.

  My answer 11 - Aug 31 is still standing.

  Hi, PA Bear.

  Hallelujah, it's fixed!    : grin:

  While working with the technical support of MS, I discovered by chance that the computer turns with KB2393802 installed if the computer is disconnected from the internet.   AKA, unplug the Ethernet cable from the computer.

  Finally, I started to wonder if the question can be hardware and not software.

  So I started picking at glitter and for me, it means generally try the easiest to accomplish the solution first.   Laughing out loud

  It was a replacement of the CMOS battery, but that didn't work.  I really didn't think he would, but hey, it was the best thing to do.

  I was going to swap hard drives, with a new installation of Home or Pro, but then I realized that it was still easier to swap the Ethernet card.

  I deleted the Linksys card (the latest version of the driver is already installed) system drew the card and dug an old map SMC EZENET of the pile of junk.  (Who doesn't have a lot of junk!   LOL) went scrounging for a driver online and got that installed, then used the device to update manager the driver, and the rest is history.

  I shut down the computer at least 10 times since (I kept a detailed log and when I hit 7 successful stops I stopped making new entries) and it worked fine every time.

  This could be something to the file in memory banks trivia!    Laughing out loud

  Thanks for the help and suggestions.

• My HP pavilion DV7 1245 x with Vista has stopped recognizing the CD.

  When I put a DVD/CD player and click on the disc or the player open, it is said, please insert the disc in the drive.  When I put a CD inside whirs for a little while but when I put a DVD in nothing happens at all.  When I ran FixIt it says fair-media is not readable, but I tried all kinds of DVD and none of them work. Can someone help me establish the popular terminology? I already deleted and reinstalled the driver several times and run Fix It twice. Thank you!

  Hello

  Check the diagnosis with the help of HP, their documentation online, and ask in their forums
  on known problems.

  Support HP & drivers
  http://welcome.HP.com/country/us/en/support.html

  Contact HP
  http://welcome.HP.com/country/us/en/contact_us.html

  HP forums
  http://h30434.www3.HP.com/PSG/

  ====================================================================

  You have disk problems as the CD/DVD is actually 4 discs in 1 case (CD & DVD burning and)
  Playback of CD and DVD). So it is not unusual for parts from 1 or 2 to not work so that others do
  correctly.

  A CD/DVD cleaner might help.

  Brand of the CD or DVD drive can also be the problem. Low quality (cheap brands) are always problematic.

  CD/DVDs have a tolerance + - and your can read/write on the edge outside these discs
  tolerances. They may be delivered, but it is generally more economical to replace the disk.

  Several good info here:
  http://Club.myce.com/

  CD/DVD units
  http://www.myce.com/storage/

  Notes on the troubleshooting and repair of readers of compact disks and CD-ROM Drives
  http://www.repairfaq.org/repair/F_cdfaq7.html#CDFAQ_014

  ===========================================

  This troubleshooting could not help if there is alignment and/or wear issues however it
  a shot.

  Step 1: Please do all the same underneath if you did some before as is often total
  a process that solves the problem.

  Try this - Panel - Device Manager - CD/DVD - double click on the device - driver tab.
  Click on update drivers (this will probably do nothing) - RIGHT click ON the drive - uninstall.
  RESTART this will refresh the default driver stack. Even if the reader does not appear to continue
  below.
  
  Then, work your way through these - don't forget the drive might be bad, could be a coward
  cable or slight corrosion on the contacts (usually for a laptop) and other issues.

  Your CD or DVD drive is missing or is not recognized by Windows or other programs
  http://support.microsoft.com/kb/314060 - a Mr Fixit

  Try this fix manually if the Fixit 314060 does not work
  http://www.pchell.com/hardware/cd_drive_error_code_39.shtml

  Your CD or DVD drive is missing or is not recognized by Windows or other programs-
  a Mr Fixit
  http://support.Microsoft.com/kb/982116

  The CD drive or the DVD drive does not work as expected on a computer that you upgraded to
  for Windows Vista
  http://support.Microsoft.com/kb/929461

  When you insert a CD or a DVD, Windows Vista may not recognize the disc
  http://support.Microsoft.com/kb/939052

  Your CD or DVD drive cannot read or write media - A Mr Fixit
  http://support.Microsoft.com/GP/cd_dvd_drive_problems

  CD/DVD drive does not appear in Windows Vista, or you receive this error in Windows
  Vista installation after booting from the DVD (AHCI)
  http://support.Microsoft.com/kb/952951
  Drive CD - R or CD - RW Drive is not recognized as a recordable device
  http://support.Microsoft.com/kb/316529/

  Hardware devices not detected or not working - A Mr Fixit
  http://support.Microsoft.com/GP/hardware_device_problems

  Another possibility is that the cables are loose. Remove ALL power, then make sure that the cables in both
  ends. Remove and replace, do not just tight. For laptops, you can often clean power and
  contacts data with a pencil eraser.

  Some DVD players do not use the Windows default drivers so check with the manufacturer of system and
  manufacturer of device to see if there is a firmware or drivers for your drive if necessary.

  ===============================

  Step 2: You have disc problems as the CD/DVD is actually 4 discs in 1 case (CD & DVD
  Burn and CD and DVD read). So it is not unusual for 1 or 2 operational so that other parts
  do it right.

  Did you follow the Troubleshooting Guide for the reader who still does not work? There are
  the entries in registry that the troubleshooter does not solve and those who "might" be the cause.

  Check with your Maker system and a device for the two possible firmware updates and
  the correct registry entries for your car.

  Here are the keys that I of course are those in question - for the subkeys of the CD/DVD drive
  as there will be other subkeys in these keys. Do not forget to ask specific keys involved as well as
  the parameters.

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Enum\IDE

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Hardware Profiles\0001\System\CurrentControlSet\Enum\IDE

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Class\ {4D36E965-E325-11CE-BFC1-08002BE10318}

  -----------------------------------------------------------------------

  You can probably find more info here and maybe even the exact registry for your CD/DVD settings
  drive from someone with the same model.

  Forums - a lot of expert real help
  http://Club.myce.com/

  CD/DVD units
  http://www.myce.com/storage/

  Use DevManView to locate the CD/DVD in the registry (be careful and do a prior Restore Point)
  nothing change) - find the DevManView device and then make a right click on it free in RegEdit.

  DevManView - free - an alternative to the standard Windows Device Manager, which displays all the
  devices and their properties in flat table, instead of the tree viewer
  http://www.NirSoft.NET/utils/device_manager_view.html

  I hope this helps.

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle="" -="" mark="" twain="" said="" it="">

• computer stopped recognizing both printers

  Until yesterday my computer recognized and easily printed through two of my ethernrt connected printers. Computer is hard wired through router as are two printers. Why is this happen and what to do to fix this. I can always print from a wireless such as my phone device.

  After resetting the printer and router several times everything is running smoothly.