computer want me to connect the printer, said unit need to be administrator

Similar Questions

• OfficeJet Pro 8500 - no USB or Ethernet cable to connect the printer to the computer?

  I'm just trying to set up my new printer Officejet Pro 8500 Wireless.  I got to the step of installing the software, but there seems to be no cable supplied to connect the printer to my computer.

  I can't currently connect via radio that I expect a new wireless router be delivered.  Is this the way onlt connection other than buying a separate USB or Ethernet cable?

  Help, please.

  Ethernet and USB cables are not usually provided with most of the printers that you need to choose a cable with a length of favourabel to you. You can go to a hardware/computer store and buy a USB A-to-B cable. I'll post a picture of the end of cable just to clear any confusion.

  

• How to connect the printer wireless hp with the computer?

  * - Original title - the printer printing

  How to connect the printer wireless hp with the computer?

  HP all what you need to be able to complete the task... See here...

  http://h71036.WWW7.HP.com/HHO/us/en/EP/articles/Wireless-Setup-Wizard.html

• Computer is configured correctly but the printer is not responding

  OK gang, this is getting really stupid! TIS happens all the time and I'm getting sick and tired of it!

  Have new HP computer and printer B210 hooked to a wireless connection running Windows 7 with IE9, series of tests and test report wireless network said "no problems found.

  I try and scan a document/picture on computer, and he answers without any link with. I run troubleshooting and returns "apperes computer is correctly configured but the device or Recorce (XXX.XXX.» "X.XXX) does not.

  I ran all the tests, made everythin thys said to do but no help.

  I called everything a few months ago and was on the phone for over an hour, turned on the control computer HP person she littered with the computer all screwed upward and it worked for a short time and return to the same problem...

  Someone out there in never never land have ideas? If if I'm going to take the advice and try it if not complicated...

  Thanks, Discusted HP person!

  Hi @cjdoxies,

  I see by your post that you are unable to scan over the network wireless to the printer to the computer. I would like to help.

  Temporarily disable any Antivirus software, to see if it interferes with communication.

  Try to start a new search.

  I have a document with a few steps to try if you are still not able to scan.

  A "connection error" or "No computer has detected" Error Message is displayed when you scan for e-all-in-one printer series HP Photosmart Plus (B210).

  If you have not already, download and run the Print and Scan doctor. It will diagnose the problem and could solve it automatically. Solution 3: Check the Scan of the computer definition also. Solution 5: Search for critical updates, hotfixes, and firmware. Follow the complete document if these 3 steps do not resolve the problem.

  If the problem persists, connect the printer directly to the computer with a USB cable and test the scanning. Just to rule out a problem of network or firewall. Were you able to scan?

  What were the results when you ran the Print and Scan Doctor? (she print or scan, all the errors-WIA, TWAIN)

  Do you have any new changes on the hardware or windows or updates of router before this problem?

  You can scan through the HP scanning software?

  If it is, then, most likely, it's a firewall or the driver may be corrupted.

  Uninstall and reinstall the printer software.

  Uninstalling the printer software.

  E-all-in-one printer HP Photosmart Plus - B210a drivers.

  Select your operating system, click Next and click on the software to download and install.

  Please provide detailed results if you're still having problems.

  Good day!
  Thank you.

• I need to install Flash Player on a computer that does not have internet access. The 'flashplayer18_d_install.exe' I copied everywhere that 'no Internet' computer wants to deal in the internet to do something and of course fails. I need a ins

  I need to install Flash Player on a computer that does not have internet access. The 'flashplayer18_d_install.exe' I copied everywhere that 'no Internet' computer wants to deal in the internet to do something and of course fails. I need an installation file that won't connect to the internet. -help

  Hi colinkerr22,

  Offline installers are displayed at the bottom of the Installation problems | Flash Player | Windows in the section "problems".

  --

  Maria

• guest computer must have access to the printer host cannot use

  I have a new Mac, an old Mac, an old Windows machine and printer of Xante AW1200.

  Almost all of my work is done on the new Mac.  I get the old machine Mac or Windows of the drawer on rare occasions, or when I need to print something, because the new Mac cannot use the printer.  (Xante never taken the trouble to develop an OS X 10.6.4 driver for this printer.)

  I would like to get rid of the Windows machine.  I have it successfully migrated to a machine of comments on the new Mac, using vmware Fusion 3.1.3 but I have not found a way to get the computer to see the printer.

  This isn't a complete surprise, as Xante does not provide a driver for their (former) printer and (my new host) operating system OS X 10.6.4 - but they were planning a WIndows XP driver that has always worked well on the Windows machine, connected by the RS232 port.

  The printer also works very well on my old Mac, connected via ethernet.

  Can I connect the printer to the new Mac's ethernet port.  Of course, the Mac cannot work with it.  But could the guest computer use Windows sound driver to manage the printer?

  None of the four standard ways of printing seem applicable: ThinPrint because the host cannot use the printer.  USB because the printer is not a USB connector.  network / wireless because I do not have my old Mac running all the time.  Hello because I think that it requires that the host can see the printer.

  It certainly isn't a frequently asked Question.  Sorry, my situation is so unusual.  But the printer is special enough for the work that I do.  Any tips?

  Thank you.

  If you have a router on your site then you should be able to connect the printer to the router, configure it as needed, and then accessing it in the comments as a network printer.  Note: The guest network should be configured as connected by a bridge to access in this way.

  Another option of network which is doable, but a little more difficult to set up, is to fix the printer directly on the Mac with a standard CAT5 Ethernet cable, not a Crossover as suggested in the Ethernet Port of Mac being automatic detection User Guide.  You would then manually configure the IP address, etc. on the printer and network bridged on the comments and even if Bridged his only access to the printer on this network adapter.  Then use a second network in the guest configured as NAT, if you do not also use Bridged on that, to enable the client to have access to other resources on the physical LAN to the host, such as Internet access, etc..

• After I start my computer dell laptop I connect the LAN cable to run internet ON my laptop but it doesn't detect LAN cable

  Hello..

  After I start my computer dell laptop I connect the LAN cable to run internet on my laptop but it does not detect the LAN cable, using the ultimate32 bites. (But if I connect LAN canble then start computer it works fine)

  Hello

  1 windows operating system is installed on the computer?

  2. do you think that no matter what error message in Device Manager? If Yes, what is the full and exact error message?

  3. What is the number of brand and model of the computer?

  Method 1:

  If you are using Windows 7, I suggest to see the link and try to run the troubleshooter and check if it works.

  Windows wireless and wired network connection problems

  http://Windows.Microsoft.com/en-us/Windows/help/wired-and-wireless-network-connection-problems-in-Windows

  The link applies to the Windows Vista and Windows 7 operating system.

  Method 2:

  Check the link and try using the network troubleshooter to fix the problem.

  Using the troubleshooter from network in Windows 7

  http://Windows.Microsoft.com/en-us/Windows7/using-the-network-troubleshooter-in-Windows-7

  See also:

  Use Network Troubleshooter event logs to solve network problems

  http://Windows.Microsoft.com/en-us/Windows7/use-Network-Troubleshooter-event-logs-to-solve-network-problems

  Method 3:

  See the link and check if it helps.

  Why can't I connect to the Internet?

  http://Windows.Microsoft.com/en-us/Windows7/why-can-t-I-connect-to-the-Internet

  Let us know if it helps.

• Computer not found displayed on the printer control panel. ?

  Computer not found displayed on the printer control panel. It analyzes not but prints ok. Running the utility HP scanner Diagnostic 4.2 says service Windows Imaging does not. If you ignore this message says the Twain service does not work because it is used by another service?

  Problem solved. I managed to get Windows Imaging served running afetr a lot of the research and this scanner enabled to work. Thanks, but does not need your help after all!

• Connect the printer via the home router

  I have LaserJet CP1525, who has a wireless option... recently I moved my router on the different floor and can not connect to my my wireless home network option trough ethernet cable/router...tried on the printer, but "failed to connect".

  any ideas? Thank you

  Hi BoleczekNieduzy,

  Welcome to the HP Forums.

  I see that you have any questions, set up the printer on the network cable and even the wireless network.
  I will do my best to help you with this problem.

  Cycle power to the router.

  First, we must restore the defaults on the printer.

  Press the OK button on the printer, go to the service, and then select restore default settings.

  Print a printer configuration page to make sure that the IP address and SSID are erased.

  Print a Configuration report.

  Select the method.

  Uninstall the printer software.
  Insert the software CD into the CD drive.
  Follow the on-screen instructions.

  When you are prompted, select the connection through the wireless network.

  If you're still having problems, restore the default values and follow this method:

  Connect the printer to the router with an Ethernet cable.
  Wait about 1 minute and the printer must have a valid IP address.
  Print the configuration page to get the IP address of the printer.
  Type the IP address in the address bar of Internet Explorer which should open the printer's built-in web services page.
  Installing wireless over here now.
  Click the networking, wireless on the left, fill in information about the network and apply the settings.
  After the confirmation, then disconnect the Ethernet cable.
  Now you should have a flashing light on the printer in 1 minute wireless about.

  Run the installation again.

  I have provided a document to configure the wireless connection, or you can follow my different methods provided.

  Installation of the software of the printer on a wireless network or network (Ethernet) cable.

  If the Wireless does not always connect, to view these settings on the router.

  You have a double router broadband?
  If it is set to 5 GHZ network, you may need to change to 2.4 GHZ. (rename the 5 GHz or turn it off)
  The WPA key setting must be on AES to work properly not TKIP.
  If it is set to the 64-bit encryption, then change it to 128-bit.
  Multi flow must be enabled.
  Router firewall must be open for printer ports.
  If you have Mac filtering give you printer hardware to meet the needs of the configuration page.

  Please let me know if this is not the problem.

  Have a great day.
  Thank you.

• I'm trying to install Adobe PS CS3 for my boss on another computer. I put the program on a hard disk and copied to the other computer now, it does not open and said he needs the license. What can I do to make it work on this computer?

  I'm trying to install Adobe PS CS3 for my boss on another computer. I put the program on a hard disk and copied to the other computer now, it does not open and said he needs the license. What can I do to make it work on this computer?

  Copy the program through a new machine will not work.   Install it using installation files and activate using the serial number assigned to the license.

  CS3 - http://helpx.adobe.com/creative-suite/kb/cs3-product-downloads.html

• I installed a driver for my printer Hp Officejet Pro L7380. How to connect the printer to the computer that works with windows vista?

  I installed a driver for my printer Hp Officejet Pro L7380. I can print from my computer and it detected that it, I can't scan anything on my computer because it is not connected. I have tryied Conect it but can not select. So my question is, how I connect printing to computer?

  Specify that you are trying to scan a document Hp Officejet Pro L7380 to your Vista machine.  It has only a single computer attached, or is it a printer networked with other computers?

  If you have installed the base drivers and not the additional software that allows scanning etc so maybe it's why you fail.

  Have a look here.

  Software & Driver Downloads
  http://h10025.www1.HP.com/ewfrf/wc/softwareCategory?OS=2093&LC=en&cc=au&DLC=en&sw_lang=&product=3198092#n190

  It might be possible with just the base drivers, for other software, such as your Photo editing programs, including painting, for import documents or images from the scanner.  Windows Fax and Scan can be able to do.  When you go in such programs are there options scan and they see your scanner?  If this is not the case, try the full download.

  If you want to of HP to make scanning programs, you may need the-base drivers and software (larger download).

  For my HP ' All in one ' works like a scanner, it was necessary for me to download all drivers and software.

• Computer laptop 13-4193nr x 360 spectrum: when I connect the printer for laptop HP spectrum x 360, Windows 10 treats like CD/DVD-ROM, no printer

  I recently bought a laptop convertible spectrum HP 13-4193nr x 360, under Windows 10 Home. When I connect our printer (HP LaserJet P1102w in black and white laser printer) port USB to the laptop, Windows can see the printer and he knows his name correct ("HP LaserJet Professional P1102w"), but does know that the device is a printer. If I go to the Panel and then devices and printers, the printer is displayed in the "Devices" line (with the laptop and the mouse) and not the line 'printers '. If I select the printer entry in the "Devices" line, Windows displays the name of the exact model of the printer, but for the "Category" field, it indicates "optical drive".

  How can I tell Windows that this device is a printer and not an optical drive?

  Hi @RHodnett,

  I'd be happy to help you install your Laserjet P1102. I understand your description that the computer does not recognize the printer as the printer and instead identifies it as an optical drive. Even if you don't see one of the errors mentioned in the following document, I think that the solutions presented may help you find a solution: Printers HP - "device installation failed" or "unknown device" message during Installation USB (Windows).

  Please let me know if that solves the problem, or if you need assistance. If the question is indeed solved, please click Accept as Solution button below. If you need additional assistance, please include any details you think could help me help you and I will do everything I can to help. Thank you.

• Photosmart Wireless B109n-z: Impossible to connect the printer wireless to the new router

  I just changed my wireless router and can not get my printer to recognize the new router.

  When you try to reinstall with the disc that came with the printer it keeps "quit unexpectedly" at the end of the installation, but before I get to connect to the printer.

  The drive indicates that it is for use with Mac OS X v10.4; 10.5, but I can't find an option to update the web site HP despite it stating that my printer is still supported.

  I can still use the printer with a USB cable connected directly to my table, but this is no help for the other devices I have.

  Hi @Paulwrow,

  Welcome to the Forums of HP Support!
   
  I understand that you are unable to connect your HP Photosmart Wireless B109n-z to your new router wirelessly. I'd be happy to see this with you and don't forget to come back to this thread and check "Accept as Solution", if I have successfully helped solve you the problem. If you want to say 'Thank you' to my effort to help, click on the "thumbs up" to give me a Kudos.
   
  The CD/DVD software will not work with newer versions of Mac OS X. HP doesn't have the drivers for this printer in Mac OS X 10.11 El Capitan. The last driver out of this printer is for Mac OS X 10.6. The only driver available that uses the driver update from Apple. This causes a problem when reconfigure the wireless, as this is the software for help. It would be easier if you have another computer running an operating system that is supported so that you can install the full feature software to configure the wireless.

  As an alternative method, you can try doing as a guideline to connect the wireless printer. We will use the ad-hoc connection. With the ad-hoc connection, you can launch the built-in web server (EWS) to access the wireless configuration wizard.
   
  Use the following steps as a guide:
  Restore the default settings of the network:

  1. Press the button next to the wireless Menu.
  2. Press the button next to wireless settings.
  3. Press the button next to network by default.

  Once the network is reset, the printer should disseminate the ad hoc connection. It should look like "hpsetup" or "HP Setup (and part of the printer name or MAC address). With an IP address like 169.82.12.44.
   
  Then, connect to the network printer, that is broadcasting.

  1. On the Mac in the upper right corner, click on the wireless icon and connect to the network "HP Setup" or "hpsetup".

  Print the wireless test report:

  1. Press the button next to Scan.
  2. Press the button next to the wireless Menu.
  3. Press the button next to wireless settings.
  4. Press the button next to run the wireless network Test.

  Browse the test report wireless IPV4 of the printer (IP address) 169.82.12.44.

  1. Launch your internet browser and enter the IP as shown. This should load the printer EWS.
  2. Click on the tab network across the top.
  3. On the left side, click on wireless or network.
  4. Run the Wireless Setup Wizard.

  This is the only way to reconfigure the wireless, unless you have another computer that has supported the software.

  For more information on the ad-hoc connection, see the User Guide.

  Please reply to this message with the result of your troubleshooting. I can't wait to hear strings attached good luck!

• Install a (wired) ethernet connected the printer on a wireless network

  I just bought a laptop from HP dm4-1050ea with Win 7 operating system 64 bit & s5780uk PC HP Pavilion Slimline, with Win 7, 64-bit operating system. I have a HP2610 Photosmart printer that is currently connected to a Dell PC, Win XP SP3, via the USB port. I want two HP computers connect to the HP printer via a Netgear DGN2000 wireless router wirelessly. I understand that the HP printer needs to be connected to the router via ethernet, however, I don't know how to proceed with the installation. The installation CD supplied with the printer's 6, Win XP, and I don't know if I should be downloading drivers to the computer laptop dm4 and Pavilion PC or just one of the computers?

  Any help on the steps to take and the order to take would be most appreciated

  Best regards

  Rathbane1

  For step 4 you have not need must be connected to the printer. As long as the printer is already connected by cable to the router it will be accessible wirelessly on the two computers during the installation of the software.

• OfficeJet Pro 8620: How can I activate the message "connect the printer to HP Instant ink status update?

  Initially, I signed up for the connected HP program but had to stop when I lost my internet connection. Wi - Fi still works. I replaced my ink cartridges instant with no instant ink with new HP ink cartridges suitable. The printer works, but before each print job I have to walk over to the printer of the touch screen and press the 'OK' button to remove a warning message that States: "connect to a printer to update HP Ink Instant status.» How can I disable this message so that I can print without having to respond each time? In addition to replacing the original instant ink cartridges, I did it 'hard' printer restarts (with the switch market), tried to restore the factory settings via the touch screen system settings, turn off internet connectivity and disable all alert settings in the HP utility. Help!

  Hello @wepj,

  Welcome to the Forums of HP and thanks much for posting!

  I want to help you with the message that you get on your HP printer officejet Pro 8620 e-all-in-one to connect to the server of ink instant.

  What it sounds like, is that there have been pages printed since the last printer connected to the HP Ink Server instant. If you cancel your account AFTER the last connection of the printer to the internet, the printer have no idea that the account has been canceled.

  I recommend you contact our Cloud Services support at 1-855-785-2777 for assistance.

  I hope this helps!