Computer will not start normally - boots to the BIOS boot screen

Similar Questions

• Computer will not start normally, in safe mode or from the recovery disk - stays on the Green loading bar of microsoft

  I got to my computer today and there was a blue screen with white writing about him say a word on the internal discharge. Then later in the day, the computer froze, after a while the screen went black with just the cursor on the screen. I restarted the computer and now it just does not start. In normal mode it gets as far as the loading screen Windows with the movement of green bar but stays on it indefinitely. If I try to start in safe mode it gets as much as crcdisk.sys and then crashes, and if I try to boot from the Vista recovery disc, it also only gets the windows loading green bar and stay on it. Any help on this would be much appreciated. Thanks in advance.

  Hello

  What is the full error message?

  Follow the suggestions and see if it helps.

  Method 1

  I suggest that do you the Startup Repair through the system recovery options with a Windows Vista installation disc.

  What are the system recovery options in Windows Vista?

  http://Windows.Microsoft.com/en-us/Windows-Vista/what-are-the-system-recovery-options-in-Windows-Vista

  Method 2

  I suggest that you perform the system restore from the system recovery options with a Windows Vista installation disc.

  What are the system recovery options in Windows Vista?

  http://Windows.Microsoft.com/en-us/Windows-Vista/what-are-the-system-recovery-options-in-Windows-Vista

  Method 3

  Perform the disk check via the system recovery options with a Windows Vista installation disc.

  a.Select command prompt.

  b.Type chkdsk /f and press ENTER.

  Note: If bad sectors are detected when running check disk utility and attempt recovery of bad sectors is verified during the verification of the drive for errors, data in the bad sector can be lost as they tried to recover bad sectors

  What are the system recovery options in Windows Vista?

  http://Windows.Microsoft.com/en-us/Windows-Vista/what-are-the-system-recovery-options-in-Windows-Vista

• My computer will not start normally upward. Audio does not work.

  original title: cannotstart in normal mode

  I can't launch in normalmode Teh networking.then audionot works. He comesonas inputnot suppoeresinapurplebox floating around monitor? helponthis specific failure? Please

  Hello

  1st thing to try is a restoration of the system in safe mode

  http://www.windowsvistauserguide.com/system_restore.htm

  Windows Vista

  Using the F8 method:

  1. Restart your computer.
  2. When the computer starts, you will see your computer hardware are listed. When you see this information begins to tap theF8 key repeatedly until you are presented with theBoot Options Advanced Windows Vista.
  3. Select the Safe Mode option with the arrow keys.
  4. Then press enter on your keyboard to start mode without failure of Vista.
  5. To start Windows, you'll be a typical logon screen. Connect to your computer and Vista goes into safe mode.
  6. Do whatever tasks you need and when you are done, reboot to return to normal mode.

  If that does not read this information

  the link below is how to download and get a vista disk startup repair, which you can start from the

  http://NeoSmart.net/blog/2008/Windows-Vista-recovery-disc-download/

  Here's how to use startup repair system restore command prompt, etc. to bleepingcomputers link below

  http://www.bleepingcomputer.com/tutorials/tutorial148.html

  to boot from the dvd drive to be able to you will see a way to get into the bios Setup at the bottom of the screen or command menu start

  It would be F2 or delete etc to enter the BIOS or F12 etc. for the start menu

  Change boot order it do dvd drive 1st in the boot order

  http://helpdeskgeek.com/how-to/change-boot-order-XP-Vista/

• Computer will not start!-boots to black screen

  OK so this is what is happening I think maybe breaking it... so I she closed and he was going to shut down, but before I did I wanted to install updates, I have so been lettng but my cat hit the power cord and it turned off I tried to restart it and that I start more... as it does all the normal show the loading bit like him bar all go and bam just a black screen... Ive put in the recovery disks, but they charge that just stop on the waiting screen please and were someone at - it something that can help me or know why it broke? original title: Vcomputer does not start!

  Have you changed the boot order to use disk recovery/s?

  Go to your Bios/Setup, or the Boot Menu at startup and change the Boot order to make the DVD/CD drive 1st in the boot order, then reboot with the disk in the drive.

  At the startup/power on you should see at the bottom of the screen either F2 or DELETE, go to Setup/Bios or F12 for the Boot Menu

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  If the recovery discs are still not working, you will need to contact the manufacturer of the computer.

  This isn't their recovery process, Microsoft.

  See you soon.

  Mick Murphy - Microsoft partner

• My computer will not start, getting warning that the iertutil.dll is missing for Internet Explorer

  Anyone know how to fix this problem? I get a warning saying that the iertutil.dll file is missing for internet explore. When I start my computer, all I get is my screensaver with no office. The only way I can continue any part of my computer is to go to alt del to get to the control task manager.

  Do you mean you see a message like this:

  Explorer.EXE - unable to locate component
  This application has failed to start because iertutil.dll was not found. Reinstalling the application may fix this problem.

  That file should never be missed and it takes an extra effort to remove it on purpose because there are one of 3498 files who cares about Protection of file Windows (WFP).

  If explorer.exe is not running, all you will see is your screen background image.

  The file is in this folder (assuming that XP is installed on your C drive):

  c:\Windows\System32

  Since you can get into the Task Manager do the following:

  Since the Task Manager, click file, new task (run...) and then click Browse and navigate to this folder:

  c:\Windows\System32\dllcache

  If you are unable to find or do not see the dllcache folder, because your system is not configured to display hidden files and folders, simply type the path to the folder name in the "Open:" box

  c:\Windows\System32\dllcache

  Make sure the "Files of type" box is set to show all files (or you will not see any), and then click OK to display all files.

  Locate copy the iertutil.dll file backup in the folder c:\windows\system32\dllcache, made a right click and copy and go back up a folder c:\windows\system32, right-click in an empty area and paste the file there.  Answered in the affirmative if invited to replace the existing file.

  If you can't find the file in the dllcache folder (should be), depending on your installation, there may be a copy of the file on your system in this folder:

  c:\windows\ServicePackFiles\i386

  If you find there, copy the file missing from there and paste it where it belongs

  It is possible that some malicious software or your antivirus/antimalware indeterminate quarantined (actually deleted) the right file and the backup copy of which must be in the dllcache folder.

  In this case, you can download a copy of my SkyDrive and use networks disks (on foot) to bring it to the system afflicted on a USB key or a floppy disk.

  You may be able to 'Run' iexplore.exe in the Task Manager to get on the Internet and just download it.

  I downloaded a copy of XP Pro SP3 file you need on my SkyDrive (everyone has a SkyDrive for file sharing).

  You can download it and when you do, place a copy of the file in these two folders (assuming that Windows is installed on your C drive):

  c:\Windows\System32
  c:\Windows\System32\dllcache (this is where XP keeps backups of important files).

  Here is the link to my SkyDrive and you can get the file you need here:

  http://CID-6a7e789cab1d6f39.SkyDrive.live.com/redir.aspx?RESID=6A7E789CAB1D6F39! 311

  When you see the files available for download, you will not see the extension of file (.exe, .dll, .cpl, .sys, etc), but when download you them they will have the right extension.

  When you download the file (especially if you use Internet Explorer), when you get a chance to save the file, it cannot save the file with an extension (for example, .exe, .dll, .cpl, .sys) then you will need to manually add the extension appropriate to the file when you download the file before you save it.

  You can download the file without the extension, and then rename the file to add the appropriate extension.  You do not want to use a file called rundll32 when the name of the file should really be called rundll32.exe (if the downloaded file has no extension, you will need to change the name of the file to add the appropriate extension to make it work.

  You then put the downloaded files in the correct folders on your system.

  That may not solve all your problems, but at least you will be spending this part and we can then fix the rest.

  Since it is all very suspicious to meI would follow with this:

  Download, install, update and do a full scan with these free malware detection programs at:
  Malwarebytes (MMFA): http://malwarebytes.org/
  SUPERAntiSpyware: (SAS): http://www.superantispyware.com/
  They can be uninstalled later if you wish.
  Restart your computer and solve the outstanding issues.

• Satellite Pro L300 will not start - cannot get into the BIOS

  Dear,

  I got a satellite Pro L300, width a HARD drive partitioned, with Win XP installed C and D with Windows 7 installed, the problem is the following:

  Days when I turned on my laptop, the OS splash screen appears, stop boot on Toshiba logo process.
  In addition, I can't enter the BIOS with the F2 key or the Boot Manager by using the F12 key.

  Help, please.

  > stop boot on Toshiba logo process
  This means that the laptop can not pass the POST (power on self test) properly and it would mean that a hardware problem has been detected on the motherboard.

  Remove one of the modules RAM (check both) and try to turn on using a single module of RAM.
  It is possible that one of the RAM modules is defective

  It would also be possible that the motherboard is malfunctioning, as you can see, it is hard to say what role could be wrong, but what looks like a serious hardware failure

• Somewhere, I messed up my permissions, turn off the computer to see if it helped, now will not start at all. The start bar stops a quarter turn along. I tried in SafeMode as well do. I ' on a Yosemite iMac running.

  Somewhere, I messed up my permissions, turn off the computer to see if it helped, now will not start at all. The start bar stops a quarter turn along. I tried in SafeMode as well do. I ' on a Yosemite iMac running. I can't enter to give more details. Can anyone help? There are a load of work due to deliver to the printing press Monday

  Have you tried to boot from the Partition Recovery and repair then the disc from there, using disk utility?

• Computer will not start at the top. I was first getting a 'file problem' message on nv4_mini.sys. After finding that someone else had...

  Computer will not start at the top. I was first getting a 'file problem' message on nv4_mini.sys. After finding that someone else had the same problem and I responded went to try the solution but then started to get the message that the file: \windows\system32\config\system is missing or corupted. Have tried to do where I could start up in safe mode and cannot. Tried to boot from the installation CD, but when I try to make the system recovery and choose the system to recover nothing happens. This isn't regarding the password. I have a Dimension 4500 XP sp3

  Hi BrianJ641,

  Follow the steps in the article.

  http://support.Microsoft.com/kb/307545

  Note: When you are prompted to type the administrator password, you can type if you set the password. If the administrator password is blank, just press ENTER.

• Vista - computer will not start without the disc

  loaded vista on my computer - now computer will not start without the disc

  Went into my bios as suggested to check the boot order - and, Yes, I got HDD1 as first boot then CD - but then I remembered something I had seen earlier on my computer - it was on the list the HD which had my system like HDD0 files - so, I checked and there it was - listed option HDD0 so I changed HDD1 of HDD0 and was able to boot my computer without the disk system.  Hope this helps someone else with the same prob.

• Virus deleted and now the computer will not start... I get the blue screen with an error that says STOP: 0x0000007B (0xB84C3524, 0xC000000E, 0x00000000, 0x00000000) what is the problem? !!

  Virus deleted and now the computer will not start... I get the blue screen with an error that says STOP: 0x0000007B (0xB84C3524, 0xC000000E, 0x00000000, 0x00000000) what is the problem? !!

  Hi ipitedafoo,

  You can check if this article helps.

  Advanced troubleshooting of errors "Stop 0x0000007B" in Windows XP

  See also:

  Error message "STOP 0x0000007B" when you restart your Windows XP-based computer

• My computer will not be stopped by using the "turn off computer' under 'Start' (lower left corner)

  My computer will not be stopped by using the "turn off computer' under 'Start' (lower left corner)

  Hi Harry,.

  · What happens when you try to stop?

  · You receive an error message or error code?

  · Do you remember all the recent changes on the computer before the show?

  · What is the service pack installed?

  You can check the link below: Windows XP Shut Down and auto-restart issues: http://www.microsoft.com/windowsxp/using/helpandsupport/learnmore/russel_02may13.mspx

  Advanced Troubleshooting for shutdown problems in Windows XP: http://support.microsoft.com/kb/308029

• Computers button just flashes and the computer will not start

  Computer on button just flashes continually and the computer will not start.  I unplugged everything and put it back together.  Same thing.  Nothing.  Monitor is on, but nothing on the screen, of course, because the computer does not start at the top.

  Computer on button just flashes continually and the computer will not start.  I unplugged everything and put it back together.  Same thing.  Nothing.  Monitor is on, but nothing on the screen, of course, because the computer does not start at the top.

  Hey Bowers

  you get a splash screen on startup with an acer for hp dell etc. or the logo of the motherboard

  otherwise, it would seem that you have a hardware problem

  Contact the manufacturer of the computer or a local reputable computer repair workshop

  Walter, the time zone traveller

• AFTER YOU INSTALL SERVICE PACK 1 FOR WINDOWS VISTA, MY COMPUTER WILL NOT START SAYS UNATTENDED, DLL

  AFTER YOU INSTALL SERVICE PACK 1 FOR WINDOWS VISTA, MY COMPUTER WILL NOT START SAYS UNATTENDED, DLL

  Follow these steps to try to solve your problems of boot.

   

  Restore point:

  http://www.howtogeek.com/HOWTO/Windows-Vista/using-Windows-Vista-system-restore/

  Do Safe Mode system restore, if it is impossible to do in Normal Mode.

  Try typing F8 at startup and in the list of Boot selections, select Mode safe using ARROW top to go there > and then press ENTER.

  Try a restore of the system once, to choose a Restore Point prior to your problem...

  Click Start > programs > Accessories > system tools > system restore > choose another time > next > etc.

  http://www.windowsvistauserguide.com/system_restore.htm

  Read the above for a very good graph shows how backward more than 5 days in the System Restore Points by checking the correct box.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

   

  If the system or Mode restore safe work not and you do not have a Microsoft Vista DVD, make a repair disc to do a Startup Repair:

  Download the ISO on the link provided and make a record of repair time it starts.

  Go to your Bios/Setup, or the Boot Menu at startup and change the Boot order to make the DVD/CD drive 1st in the boot order, then reboot with the disk in the drive.

  At the startup/power on you should see at the bottom of the screen either F2 or DELETE, go to Setup/Bios or F12 for the Boot Menu.

  When you have changed that, insert the Bootable disk you did in the drive and reboot.

  http://www.bleepingcomputer.com/tutorials/tutorial148.html

  Link above shows what the process looks like and a manual, it load the repair options.

  NeoSmart containing the content of the Windows Vista DVD 'Recovery Centre', as we refer to him. It cannot be used to install or reinstall Windows Vista, and is just a Windows PE interface to recovering your PC. Technically, we could re-create this installation with downloadable media media freely from Microsoft (namely the Microsoft WAIK, several gigabyte download); but it is pretty darn decent of Microsoft to present Windows users who might not be able to create such a thing on their own.

  Read all the info on the website on how to create and use:

  http://NeoSmart.net/blog/2008/Windows-Vista-recovery-disc-download/

  ISO Burner:http://www.snapfiles.com/get/active-isoburner.html

  It's a very good Vista startup repair disk.

  You can do a system restart tool, system, etc it restore.

  It is NOT a disc of resettlement.

  And the 32-bit is what normally comes on a computer, unless 64-bit.

  See you soon.

  Mick Murphy - Microsoft partner

• I have Windows 7, my computer does not start. I did the Startup Repair and he won't fix it. I did the system configuration information

  I have Windows 7, my computer does not start. I did the Startup Repair and he won't fix it. I did the system configuration information. and that did not help. What to do now? The comment of Bios makes me fear that it could damage my computer forever. What should do? Help, please

  Hi Alan,

  Thanks for posting your query in Microsoft Community.

  I understand that the computer does not restart even after running Startup Repair and I will be happy to answer your query. I appreciate the efforts made to try to make it work. Let me ask you;

  • How do you run the Startup Repair?
  • Do you have Windows 7 repair disc?
  • Remember to no particular change in the computer before the show?
  • Have you plugged an external equipment, except the keyboard and mouse?
  • You are able to start the computer in safe mode?
  • What is the brand and model of the computer?

  Note: BIOS change / semiconductor (CMOS) to complementary metal oxide settings can cause serious problems that may prevent your computer from starting properly. Microsoft cannot guarantee that problems resulting from the configuration of the BIOS/CMOS settings can be solved. Changes to settings are at your own risk.

  There could be several reasons why he's not leaving including hardware as well. In addition, it could be because the master boot record (MBR) has been damaged. When you try to use the Startup Repair tool to repair the MBR, the Startup Repair tool indicates that no problem was found or it does not work yet.

  If you have any connected USB flash drive or other external devices connected to the computer, if you please, remove them and try to run the Startup Repair tool.

  If you haven't tried using Windows 7 repair disc, you can try the following:

  1. Insert the Windows 7 disc
  2. restart your computer
  3. When asked if you want to boot from your DVD player, do it.
  4. Select your language, click Next.
  5. click on repair your computer
  6. Select the operating system you want to repair.

  You can also perform the system restore by selecting the restore point when you think it worked very well. System Restore, choose advanced options using the disc.

  Important: When you use system restore to restore the computer to a previous state, the programs and updates that you have installed after this date are deleted.

  I also recommend to contact the computer manufacturer to get the done diagnostic equipment.

  Hope this information is useful. Please feel free to answer in the case where you are facing in the future other problems with Windows.

• I downloaded bridge in my application, but it will not start when I click the icon

  I downloaded bridge in my application, but it will not start when I click the icon

  Hello

  Did you try to unsintall and reinstall the application?

  Kind regards

  Sheena