configuration Cisco No. 2851 IPS intrusion prevention system

Similar Questions

• Configuration Cisco AP 2600 (AIR-CAP2602I-E-K9) and Cisco 2500 wireless controller?

  This is the first time that I work with this type of devices (Cisco Ap 2600 (AIR-CAP2602I-E-K9) and wlc 2500)... my experience to the CCNP (router and Switch)

  How configuration Cisco Ap 2600 (AIR-CAP2602I-E-K9) and wlc 2500?

  Please find attachment (Cisco device map)

  

  Hello

  Here are the docs for you to configure the Basic for AP switch port configuration IE 2600 s and wlc.

  WLC port must be configured as a trunk.

  Port of the AP must be access.

  CAP2600 series requires software 7.2.110.0 wlc minimum (make sure you have it or above release)

  Upgrade if you follow it.

  http://www.Cisco.com/en/us/Tech/tk722/tk809/technologies_configuration_example09186a00805f381f.shtml

  1. http://www.cisco.com/en/US/products/ps6366/products_configuration_example09186a0080665cdf.shtml (SW port configs)

  2. http://www.cisco.com/en/US/tech/tk722/tk809/technologies_tech_note09186a00806c9e51.shtml

  (Another thing very importand, discovery mechanism, choose properly)

  If you choose the option dhcp 43, it uses the TLV format. Type is always f1, the length is 4 * (wlc number for which you want to provide discovery for, in your case) Value = Hex conversion of the wlc management ip address.

  A video for the process of

  http://www.youtube.com/watch?v=oOh_Iv1CHxQ.

  Thank you

  Sahil

• Cisco No. 2851 with 2 - FPS?

  Hi all

  First of all you wishing all happy new year!

  I want to know if it is - it possible to connect 2-HWIC-SFP modules (1 GB) router Cisco No. 2851?

  A single.   See below (table 3).

  High-speed Cisco Gigabit Ethernet WAN Interface Card

• What is the purpose for the activation and the deactivation of the modules? (Symantec Corp.Norton 360: "Symantec Intrusion Prevention add-on")

  What is the purpose for the activation or deactivation of the modules? Initially, Symantec Intrusion Prevention module is disabled, I should allow it, and how might it affect my computer?

  Not a Windows issue. Best thing is to visit the Norton FAQ or read the help files.

• Help to configure cisco

  Hi all

  I need your help here I am trying to configure a router Cisco 881 when infact I have a connection which reached the Wan port on the router, I set up 88.le XXX (public IP) I put the default gateway etc... his short film works because when I ping the IP to the outside, than it works
  My problem, I want to have internet on my FastEthernet port 0, I configured a dhcp 192.168.0.X albums pool it works but I got no internet despite having the nat outside inside put the road, so I added a static route, but it is not the copy of my config work thank you.

  1 running-config #show
  Building configuration...

  Current configuration: 5424 bytes
  !
  ! Last configuration change at 15:56:09 UTC Thursday, March 13, 2014 by admin
  version 15.2
  no service button
  horodateurs service debug datetime msec
  Log service timestamps datetime msec
  no password encryption service
  !
  hostname R1
  !
  boot-start-marker
  boot-end-marker
  !
  !
  logging buffered 51200 warnings
  !
  No aaa new-model
  iomem 10 memory size
  !
  Crypto pki trustpoint TP-self-signed-2132292671
  enrollment selfsigned
  name of the object cn = IOS - Self - signed - certificate - 2132292671
  revocation checking no
  rsakeypair TP-self-signed-2132292671
  !
  !
  TP-self-signed-2132292671 crypto pki certificate chain
  certificate self-signed 01
  3082022B XXXXXXXXXXXXXXXXXXXXXXXXXXXX
  !
  !
  !
  DHCP excluded-address IP 10.10.10.1
  DHCP excluded-address IP 192.168.0.254
  !
  DHCP IP CCP-pool
  import all
  Network 10.10.10.0 255.255.255.248
  default router 10.10.10.1
  Rental 2 0
  !
  IP dhcp pool vlan5
  network 192.168.0.0 255.255.255.0
  default router 192.168.0.254
  Server DNS 8.8.8.8
  !
  !
  !
  no ip domain search
  "yourdomain.com" of the IP domain name
  IP cef
  No ipv6 cef
  !
  !
  license udi pid CISCO881-K9 sn FCZ18047124
  !
  !
  !
  !
  !
  !
  !
  property intellectual ssh version 2
  !
  !
  !
  !
  !
  !
  !
  !
  !
  interface FastEthernet0
  switchport access vlan 5
  no ip address
  !
  interface FastEthernet1
  no ip address
  !
  interface FastEthernet2
  no ip address
  !
  interface FastEthernet3
  no ip address
  !
  interface FastEthernet4
  IP 84.14.XXX. X 255.255.255.248
  NAT outside IP
  IP virtual-reassembly in
  automatic duplex
  automatic speed
  !
  interface Vlan1
  Description $ETH_LAN$
  IP 10.10.10.1 255.255.255.248
  IP tcp adjust-mss 1452
  !
  interface Vlan5
  IP 192.168.0.254 255.255.255.0
  !
  default IP gateway - 84.14.209.185
  IP forward-Protocol ND
  IP http server
  23 class IP http access
  local IP http authentication
  IP http secure server
  IP http timeout policy slowed down 60 life 86400 request 10000
  !
  IP nat inside source list 2 interface FastEthernet4 overload
  IP route 0.0.0.0 0.0.0.0 84.14.209.185
  !
  access-list 2 allow 192.168.0.0 0.0.0.255
  not run cdp
  !
  !
  exec banner ^ C
  % Warning of password expiration.
  -----------------------------------------------------------------------

  Professional configuration Cisco (Cisco CP) is installed on this device
  and it provides the default username "cisco" single use. If you have
  already used the username "cisco" to connect to the router and your IOS image
  supports the option "unique" user, that user name is already expired.
  You will not be able to connect to the router with the username when you leave
  This session.

  It is strongly recommended that you create a new user name with a privilege level
  15 using the following command.

  username secret privilege 15 0

  Replace and with the username and password you
  you want to use.

  -----------------------------------------------------------------------
  ^ C
  connection of the banner ^ C
  -----------------------------------------------------------------------
  Professional configuration Cisco (Cisco CP) is installed on this device.
  This feature requires the unique use of the user name "cisco" with the
  password "cisco". These default credentials have a privilege level of 15.

  YOU MUST USE CISCO CP or the CISCO IOS CLI TO CHANGE THESE
  IDENTIFICATION INFORMATION PUBLICLY KNOWN

  Here are the Cisco IOS commands.

  username secret privilege 15 0
  No username cisco

  Replace and with the username and password
  to use.

  IF YOU DO NOT CHANGE THE IDENTIFICATION INFORMATION PUBLICLY KNOWN, YOU WILL HAVE
  NOT BE ABLE TO CONNECT TO THE DEVICE AGAIN ONCE YOU HAVE DISCONNECTED.

  For more information about Cisco CP, you follow the instructions of the
  Of your router's QUICK START GUIDE or go to http://www.cisco.com/go/ciscocp
  -----------------------------------------------------------------------
  ^ C
  !
  Line con 0
  local connection
  no activation of the modem
  line to 0
  line vty 0 4
  access-class 23 in
  privilege level 15
  password
  opening of session
  entry ssh transport
  line vty 5 15
  access-class 23 in
  privilege level 15
  local connection
  transport input telnet ssh
  !
  !
  end

  Add below

  interface Vlan5

  IP nat inside

• How to configure a Cisco No. 2851 to access customer VPN Cisco router?

  It is my current configuration below, can someone help me see problems with it:

  AAA new-model
  !
  !
  AAA authentication local connection user
  AAA authorization network group local
  AAA accounting update newinfo

  crypto ISAKMP policy 10
  BA 3des
  preshared authentication
  !
  crypto ISAKMP policy 11
  BA 3des
  preshared authentication
  Group 2
  !
  12 crypto isakmp policy
  BA 3des
  md5 hash
  preshared authentication
  Group 2
  !
  crypto ISAKMP policy 15
  BA 3des
  md5 hash
  preshared authentication
  Group 2
  !
  crypto ISAKMP policy 20
  md5 hash
  preshared authentication

  !
  ISAKMP crypto client configuration group vpngroup
  key cisco123
  pool VPN_POOL

  Crypto ipsec transform-set esp-3des esp-sha-hmac vpnc1
  !
  Crypto-map dynamic dynmap 15
  Set transform-set vpnc1
  !
  !

  local IP 10.1.1.1 VPN_POOL pool 10.1.1.20

  list user card crypto Test client authentication
  card crypto isakmp authorization list Group Test
  Crypto map Test address client configuration address
  Discover 15 Test card crypto ipsec-isakmp dynamic dynmap
  !
  !
  !
  !
  interface GigabitEthernet0/0
  Description *.
  IP address
  NAT outside IP
  IP virtual-reassembly
  automatic duplex
  automatic speed
  No cdp enable
  card crypto Test

  Hi Ralema,

  Please see this link:

  http://www.Cisco.com/en/us/Tech/tk583/TK372/technologies_configuration_example09186a00800949ba.shtml

  It will be useful.

  Federico.

• Cisco JOINT and IPS hardware bypass

  Hi all

  I have a question about the Cisco JOINT, ASA - AIP - SSM (IPS) and material of the IPS 4200 bypass unit series. Please let me know if the material fails in both cases how to cross traffic. Is there any circumvention of integrated equipment built in the same

  Concerning

  Ankur

  Sorry for the late reply. I've been on vacation for a week.

  ByPass hardware is not available for the JOINT-2 no matter if you use inline vlan pairs or couples inline interface.

  For devices need special interface cards or a hardware bypass switch separate, and none of them are available on the JOINT-2.

  You must configure your network so that there is a second way around the JOINT 2 JOINT-2 failure.

  This can be done with a standard network cable.

  Suppose you have your JOINT-2 configured for inline vlan VLAN 10 matching and 20.

  Configure a standard switchport as an access port on vlan 10.

  Set up an another standard switchport as an access port on vlan 20.

  Now using a standard network cable connect these 2 all switch ports.

  Stop your JOINT-2 and traffic should now be passed through this network cable and your network connectivity must be maintained.

  Bring your JOINT-2 backup, and now spanning tree runs and will choose the JOINT-2 or the network as the main way and the other cable will set in a State of block.

  Run ' show vlan spanning-tree 10 ' and ' show vlan spanning tree 20 "to determine if the cable ports or port JOINT-2 is in a BLK State.»

  If the cable ports are in a State BLK, then you don't need to modify the spanning tree.

  If the JOINT-2 port is in a State BLK, then you need to change the spanning tree cost and/or priority for JOINT-2 port by using the following commands:

  -[No] port-channel channel_number-STP intrusion detection doesn't cost port_cost

  Defines the cost of port tree covering for the data port on the specified module. Without the option restore shipping tree covering for the data port on the module specified in the default value.

  -[not] port-channel channel_number spanning tree priority priority intrusion detection

  Sets the priority of the port spanning tree for the data port on the specified module. Without the option restores the priority of port spanning tree for the data port on the module specified in the default value.

  To learn more about spanning-tree and how these parameters interact with spanning tree you can look through this section of the user guide for the switch or to search cisco.com for documentation of spanning tree:

  http://www.Cisco.com/en/us/partner/docs/switches/LAN/catalyst6500/IOS/12.2Sx/configuration/guide/spantree.html

  NOTE: Your switch must be configured for rapid PVST for failover more rapid. Work with your administrator to switch to determine which spanning tree Protocol is used on your switch. The JOINT-2 does not work with STDS to ensure that STD is not used.

• Configuration Cisco 1921

  I am configuring a Cisco 1921 router to connect with my cable modem.  The router gets an IP address from the DHCP server and I can ping resources on the internet on the router.   The router distributes DHCP addresses to clients, but clients are unable to access the internet.  I'm missing something simple.  Here is my config:
  
  R1-1921 #sh run
  Building configuration...
  Current configuration: 6236 bytes
  !
  ! 19:11:22 EST configuration was last modified Thursday, November 5, 2015 by *.
  version 15.3
  horodateurs service debug datetime msec
  Log service timestamps datetime msec
  no password encryption service
  !
  hostname R1-1921
  !
  boot-start-marker
  boot system flash: c1900-universalk9-mz. Spa. 153 - 3.M6.bin
  boot-end-marker
  !
  !
  logging buffered 51200 warnings
  enable secret 5 $1$ F3oi$ EtowSjpBITAVsWVxr4EDM.
  activate the password *.
  !
  No aaa new-model
  No process cpu extended history
  No pork process autoprofile cpu
  iomem 10 memory size
  clock timezone IS - 5 0
  clock to summer time EDT recurring
  !
  !
  !
  !
  DHCP excluded-address 192.168.1.1 IP 192.168.1.100
  DHCP excluded-address IP 192.168.1.201 192.168.1.254
  DHCP excluded-address 192.168.2.1 IP 192.168.2.100
  DHCP excluded-address 192.168.2.201 IP 192.168.2.254
  DHCP excluded-address IP 10.10.10.1 10.10.10.100
  DHCP excluded-address IP 10.10.10.201 10.10.10.254
  DHCP excluded-address IP 192.168.20.1 192.168.20.100
  DHCP excluded-address IP 192.168.20.201 192.168.20.254
  !
  IP dhcp pool vlan2_Home_DHCP
  network 192.168.2.0 255.255.255.0
  F104.0a0a.140b hexagonal option 43
  domain name *.
  Server DNS 8.8.8.8 8.8.4.4
  default router 192.168.2.254
  Rental 7
  !
  IP dhcp pool vlan10_Home_DHCP
  Network 10.10.0.0 255.255.0.0
  F104.0a0a.140b hexagonal option 43
  domain name *.
  default router 10.10.10.1
  Server DNS 8.8.8.8 8.8.4.4
  Rental 7
  !
  IP dhcp pool vlan20_Home_DHCP
  network 192.168.20.0 255.255.255.0
  F104.0a0a.140b hexagonal option 43
  domain name *.
  Server DNS 8.8.8.8 8.8.4.4
  default router 192.168.2.254
  Rental 7
  !
  IP dhcp pool vlan1_Home_DHCP
  network 192.168.1.0 255.255.255.0
  F104.0a0a.140b hexagonal option 43
  domain name *.
  Server DNS 8.8.8.8 8.8.4.4
  by default-router 192.168.1.254
  Rental 7
  !
  !
  !
  IP domain name *.
  IP cef
  No ipv6 cef
  !
  Authenticated MultiLink bundle-name Panel
  !
  !
  Crypto pki trustpoint TP-self-signed-2424561219
  enrollment selfsigned
  name of the object cn = IOS - Self - signed - certificate - 2424561219
  revocation checking no
  rsakeypair TP-self-signed-2424561219
  !
  !
  TP-self-signed-2424561219 crypto pki certificate chain
  certificate self-signed 01
  3082022B 30820194 02020101 300 D 0609 2A 864886 F70D0101 05050030 A0030201
  2 060355 04031326 494F532D 53656 C 66 2 AND 536967 6E65642D 43657274 31312F30
  69666963 32343234 35363132 6174652D 3139301E 170 3135 31313032 31383034
  35395A 17 0D 323030 31303130 30303030 305A 3031 06035504 03132649 312F302D
  4F532D53 5369676E 656C662D 43 65727469 66696361 74652 32 34323435 65642D
  36313231 3930819F 300 D 0609 2A 864886 01050003, 818, 0030, 81890281 F70D0101
  81008E99 C46CD1DA 4626A4A1 614268 HAS 4 FC70E1B0 66E4D691 6F1DDA9E EE15D3D6
  44469CAF D9EB6EAF B155D164 5E75CD1E B0541204 98C7BC8A E973A18A 852F7BC3
  09B33BDB C4C63C75 4C8B7A60 BA3BB4E7 C980BDFA 35F50803 C92973F4 19A 90217
  48E993E3 BFC1EE4D C9A8ABE7 C094E89B 9629195A 0763605 A D577278C B8C39AB9
  010001A 3 53305130 1 130101 FF040530 030101FF 301F0603 0F060355 0CEF0203
  551 2304 18301680 14B9ECCC A5378EAC C33EA600 3A11948F 56021544 74301 06
  03551D0E 04160414 B9ECCCA5 378EACC3 3EA6003A 11948F56 02154474 300 D 0609
  2A 864886 05050003 81810046 FC666C70 E65C191B 951D69CC BE68D6D1 F70D0101
  B5EC7175 ED432B26 7C44E882 1 C 04F30A7C 006392 E782CB04 CC898FD4 2B5F9085
  A84DB5BA 0996408A 46D36AE7 20A4BADA D418EC0D F7A94E46 08782215 C7EEF16F
  998E78F0 17026E9A 0705D4F7 FCEEED19 AB467E35 6A8E2CED A35BD0C3 236CF87D
  76F3BF78 45D940EF DF0A8934 D411F3
  quit smoking
  
  udi pid CISCO1921/K9 sn license *.
  !
  !
  !
  redundancy
  !
  !
  !
  !
  !
  property intellectual ssh time 60
  !
  !
  !
  !
  !
  !
  !
  !
  !
  interface Loopback0
  172.40.59.1 the IP 255.255.255.255
  !
  the Embedded-Service-Engine0/0 interface
  no ip address
  Shutdown
  No cdp enable
  !
  interface GigabitEthernet0/0
  no ip address
  automatic duplex
  automatic speed
  No cdp enable
  No mop enabled
  !
  interface GigabitEthernet0/0.1
  encapsulation dot1Q 1 native
  IP 192.168.1.253 255.255.255.0
  No cdp enable
  !
  interface GigabitEthernet0/0.2
  encapsulation dot1Q 2
  192.168.2.253 IP address 255.255.255.0
  No cdp enable
  !
  interface GigabitEthernet0/0.10
  encapsulation dot1Q 10
  IP 10.10.10.1 255.255.0.0
  No cdp enable
  !
  interface GigabitEthernet0/0.20
  encapsulation dot1Q 20
  address 192.168.20.1 255.255.255.0
  No cdp enable
  !
  interface GigabitEthernet0/1
  DHCP IP address
  no ip redirection
  no ip proxy-arp
  NAT outside IP
  IP virtual-reassembly in
  automatic duplex
  automatic speed
  No cdp enable
  !
  IP forward-Protocol ND
  !
  no ip address of the http server
  local IP http authentication
  IP http secure server
  IP http timeout policy slowed down 60 life 86400 request 10000
  !
  IP nat inside source list 1 interface GigabitEthernet0/1 overload
  IP default-network 192.168.1.0
  IP route 0.0.0.0 0.0.0.0 dhcp 20
  !
  no routing capabilities-Manager service
  not run cdp
  !
  !
  access-list 1 permit 192.168.1.0 0.0.0.255
  access-list 2 allow to 192.168.10.0 0.0.0.255
  access-list 2 allow 192.168.20.0 0.0.0.255
  access-list 2 allow 192.168.30.0 0.0.0.255
  access-list 2 permit 192.168.40.0 0.0.0.255
  access-list 2 allow to 192.168.1.0 0.0.0.255
  access-list 2 allow 10.10.20.0 0.0.0.255
  access-list 3 Let 192.168.10.0 0.0.0.255
  access-list 3 allow 192.168.20.0 0.0.0.255
  access-list 3 allow 192.168.30.0 0.0.0.255
  access-list 3 permit 192.168.40.0 0.0.0.255
  access-list 3 Let 192.168.1.0 0.0.0.255
  access-list 23 allow 10.10.10.0 0.0.0.7
  !
  control plan
  !
  !
  !
  Line con 0
  exec-timeout 0 0
  local connection
  line to 0
  line 2
  no activation-character
  No exec
  preferred no transport
  transport output pad rlogin lapb - your MOP v120 udptn ssh telnet
  StopBits 1
  line vty 0 4
  privilege level 15
  local connection
  transport of entry all
  line vty 5 15
  privilege level 15
  local connection
  transport of entry all
  !
  Scheduler allocate 20000 1000
  !
  end

  Your modem might need routes to subnets and the NAT configuration for these subnets.

  However, another way to do it is NAT CBC all IP addresses to the IP of the interface gi0/1 looks you can try to do.

  If you don't then.

  (1) you must add 'ip nat inside' to every subinterface

  (2) the ACL for your NAT made reference only 192.168.1.x customers while your other ACL refers all subnets.

  If you want to have all subnets access the internet turn it into NAT reference one another ACLs

  (3) don't know what you're doing with the statement "ip default-network 192.168.1.0.

  Just remove it and use the default route you have in your configuration and you don't need to add an ad at the end.

  Jon

• Configuration Cisco 1841

  Hi all

  I work for a company of Radio 2-way, we use Motorola equipment.  One of the systems requires a router for each repeater site. Motorola recommends a MSR20 20 HP router. I set up this router before and it works great but I would use cisco vs. HP equipment.  I'm having issues reflecting the way in which we present the HP router to the CLI on the Cisco 1841.  I'd appreciate any help that someone is willing to offer.

  Here's how the HP router is configured in the CLI...   Thank you!!

  pic1.jpg

  

  Pic2.jpg

  

  pic3.jpg

  

  pic4.jpg

  

  pic5.jpg

  

  Hello

  the following is the equivalent of Cisco for the yellow highlisghted lines:

  !hostname Site1!int Eth0/0  ip nat outide  ip address 192.168.1.1 255.255.255.0!int Eth0/1  ip nat inside  ip address 10.1.1.1 255.255.255.0!ip nat inside source static udp 192.168.1.10 55001 10.1.1.1 55001ip nat inside source static udp 192.168.1.11 55011 10.1.1.1 55011ip nat inside source static udp 192.168.1.12 55012 10.1.1.1 55012!ip route 0.0.0.0 0.0.0.0 10.1.1.254!

  Cheers, Seb.

• Configuration of several peers IPs for VPN Site to Site on a firewall context

  I'm running a version of 5585 Cisco ASA firewall 9.1. I use the context mode to meet my clients of different clouds. I have a new client who needs a VPN from Site to Site to a remote location. Remoteness have three counterparts IPs configured in failover mode I need to configure on my end.

  Please tell us if this is possible and how to go about configuring.

  A context is just like any independent, just virtualized firewall. I did it and it worked fine for me.

  --

  Please do not forget to select a correct answer and rate useful posts

• Configuration Cisco AnyConnect secure mobility assistance

  Hello!

  A partner of CIsco of Singapore asks if it would be possible on Cisco Anyconnect Secure Mobility

  If I want to use "Cisco AnyConnect Secure mobility" in Anyconnect 3.0, I can set that the user is not able to access all traffic via a wireless sound card when the VPN is established via the wired LAN port. I want to prevent any bypass between these two network ports if the VPN in place.

  In addition, to enable split tunneling so that all traffic has to go through the VPN tunnel?

  Kind regards!

  Ice Flancia

  Cisco partner Helpline Tier 2 team

  To route all traffic to the VPN tunnel, split tunnel should be turned off (not enabled).

  Under group policy configuration: split-tunnel-policy tunnelall

  Once the split tunnel is disabled, VPN users will not be able to access one of its local LAN networks (including wireless).

  Hope that helps.

• Channel configuration of the individual on a CCS system

  All,

  I work with an old system of CSC with the following modules:

  2@AI03

  3@TC02

  2@SG24

  1@AI05

  The orginal VI for this system use DAQ Assistant to configure each module individually, with different signal input range, put across the Terminal configuration and custom scale units.  See attached photos.

  I write new code, but I don't usually use DAQ Assistant.  Is it possible to configure each module individually without DAQ Assistant job?  I tried to configure the modules directly, but I get "Resource unavailable" errors when I try to run the code.

  Or should I just gritted my teeth and use the DAQ Assistant?

  Thanks for any help.

  Since they are chained, they run one after the other, but the task with all channels will start when you order him.

• Windows could not configure one or two components of the system.

  I get this message after completing my update, Vista Home Premium 64 Vista Ultimate 64. All solutions?

  Hello

  1 you have a Windows Ultimate Upgrade disc, a complete edition of the full Windows disk or a Windows Anytime Upgrade disc?

  2 - is Windows XP or Windows Vista already exist on the computer before you install Windows Vista Ultimate?

  Currently, I suggest referring to the following troubleshooting article and thread:

  Windows could not configure one or more system components

  http://forums.Microsoft.com/technet/ShowPost.aspx?PostID=2409427&siteid=17

  Error message when you try to upgrade Windows Vista to a more advanced version of Windows Vista: "Windows cannot configure one or more system components to install Windows, restart the computer, and restart the installation.

  http://support.Microsoft.com/kb/946078/en-us

• Everytime I turn on my laptop, I get a warning that the Data Execution Prevention System has stopped working. Any ideas how to fix this, please?

  Running Windows Vista family - that's all as far as I know!

  Hi Norfolk broad,

  Remember to make changes?

  Method 1:  Put the computer to boot and then check if the problem persists

  Follow step 1 in the link below,

  How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7

  If everything works well after a clean boot, you can deduce that some third-party services are at the origin of the problem.

  Continue with the remaining steps to pin-point on the third party service.
  After find you the program that is causing the problem, you will have to perhaps to update or install a newer version of the program, if you rarely use that you should consider uninstalling the software.

  Important: n ' forget not to put the computer to a normal startup follow step 7 in the link.

  
  Method 2: if a Protection of resources Windows (WRP) file is missing or is damaged, Windows may not behave as expected. Auditor of file system (CFS) scan to fix all of the corrupted system files. To do this, follow the steps mentioned in the link below:

  How to use the System File Checker tool to fix the system files missing or corrupted on Windows Vista or Windows 7

  http://support.Microsoft.com/kb/929833

  See the link below for more information on the execution prevention (DEP) data
  http://Windows.Microsoft.com/en-us/Windows-Vista/data-execution-prevention-frequently-asked-questions

• Backup of configuration Cisco Codec C40

  Dear all,

  Can I know how to take backup of the configuration of the Cisco Codec C40, please?

  And also help me with the document of the administrator?

  Thanks in advance

  Kind regards

  Syed

  You can simply copy the output of the xConfiguration and paste it into the SSH client.  You may need to change the output a bit to get the correct formatting, however.  For example, the output registered since my SHH client contains a preceding * c which must be removed before that I can stick again in the SSH client:

  *c xConfiguration Video Wallpaper: Waves

  When you perform a software update, codec configuration, including the keys installed option is not affected and will remain in the process. Keys options include Premium (PR), double (DD) display resolution and Multisite (MS). C40 has been end of sales since June 2015, so it is not possible to order anything for this, see eos-eol-notice-c51-733467. Procedure to upgrade the software codec is on pg 28, the same page mentioned in my previous answer. To upgrade codec software, you will need a release key when switching from one major version to another, as TC5 to TC7. You can request a release of the Cisco Licensing Portal key > obtain other Licenses > telepresence free software key, as long as the device has an active support contract. If you do not have an active support contract, you can contact TAC and get the free unlock key by referencing the Security Advisory cisco-sa-20160504-tpxml, which you can get a key to unlocking TC7.