Remote Desktop and Cisco Small Business RV042

Similar Questions

• Plug-and-Play for Cisco Small Business 300 Series managed switch

  Nice day

  What are the automatic installation options available for the Managed Switch series of Cisco Small Business 300?

  It seems there are not, the operating system is not the standard IOS I used to.

  I would use with ability to bridge the Infrastructure first Cisco PnP.

  Concerning

  Stone

  First Infrastructure use and assume an agent CNS (Cisco Network Services) on the other side, when you enable the 'plug & play '. Series 300/500 do not run IOS and does not include the CNS agent, but there is a way to activate the automatic configuration. Switches supported by the automatic DHCP configuration (using DHCP options 66, 67, etc.) in which case they automatically download their config to a TFTP server at boot time. This allows an administrator to put the configs for all switches on a TFTP server and simply start a default switch factory in order to obtain config.

  Seal a document shows how this is done.

  Hope that the information would be useful.

• Accounting on a Cisco Small Business SF300-08

  Hello

  "Cisco Small Business 300 Series managed switches Administration Guide" and the sheet indicate that this switch can make requests of accounting with a Radius server. On the switch interface/CLI SF300, there is that the authentication port, the port of account cannot be resolved (and nothing is sent by the switch to the default port). I guess that the SF300-08 doesn't manage accounting. Maybe I need to change to another model. Could you give me another model in the same price range?

  Thank you

  Laurent.

  Hi Laurent, I am pleased that the 1.2.5.70 has solved this problem.

  Please keep Advisory of the 1.2.5.70 firmware has also been lifted for now.

  Please note that we have identified a potential problem with the 1.2.5.70 update for the series 200, 300 and 500 switches. As a precaution, we took down the 1.2.5.70 free while we determine the cause of the issue, the seriousness and the scope. We re - ask the release or publish an updated based on the results of our analysis.

• Weired problem with Remote desktop and WLan on Tecra M7

  Hello

  I regularly use Microsoft Office remote to connect to my work PC to my laptop (TOSHIBA TECRA M7 Tablet) home.
  However, since buying (not had long), the remote desktop connection drops and I can't reconnect to the Toshiba laptop.

  It seems that when I connect to the start via Remote Desktop and the connection start screen appears after a short time 10-25mins laptop Toshiba Wifi connection drops.
  When I try to reconnect it does not allow me to do.
  I have to physically come back home and logon to windows XP and then re - activate the wifi.

  I did the following to here.

  1 UPDATE the latest BIOS
  2 UPDATE WIFI INTEL PRO ADAPTER TO THE LATEST DRIVERS
  3. NOT MY BROADBAND, AS PREVIOUSLY, HE WORKED WITH HAPPINESS ON MY OLD LAPTOP.
  4. NOT MY WORKING BROADBAND CONNECTION WORKED FINE BEFORE AND IS STILL WORKING ON THE OLD INSTALLATION
  5. HAVE YOU TURNED OFF ALL THE POWER ON THE LAPTOP AND WIFI PROPERTIES MANAGEMENT, WHERE HE WOULD SLEEP.

  PLEASE HELP, IT IS NECESSARY FOR EMERGENCY

  Hello

  Do you use the Intel Proset utility to configure the WiFi connection?
  Try to configure the WiFi network using this tool and check if the WiFi network would disconnect again.

  I m also interesting this driver Wlan did you use?
  Did you use one page of Intel?
  If this is not the case, check the Intel page for the new WLan driver version.

• What is the difference between the activation of remote desktop and adding a 'connection in network connections.

  What is the difference between the activation of remote desktop and adding a 'connection in network connections.

  Hi ChadCrowell,

  Remote Desktop connection allows remote control of your Windows XP Professional computer from another computer running Windows XP Professional or an earlier version of Windows.

  Reference: How to use the Windows XP Professional Remote Desktop feature?

  By creating an incoming connection, a computer can act as a remote access server is running Windows XP Professional, Windows 2000 Professional

  Reference: To make an incoming network connection

  Hope the helps of information.

• Configuration of SNMP on Cisco Small Business 300 Series managed switch

  Please can someone help me configure SNMP on Cisco Small Business 300 series switch?

  Thank you

  Hi Anton,.

  Don't forget to activate the service SNMP is first of all: Security > Services TCP/UDP.

  http://sbkb.Cisco.com/CiscoSB/UKP.aspx?VW=1&docid=3b13278d9ef9402a8fef57...

  also, you will find useful documents for configuration etc on our server community kb:

  http://sbkb.Cisco.com/CiscoSB/UKP.aspx?VW=1&docid=183cae2148d445b2a07473...

  Let us know if you have any problems.

  Aleksandra

• Router Cisco Small business with the functionality of the link aggregation

  Hi all!

  can someone tell me if there is a router from Cisco Small business with the functionality of the link aggregation? (I want to connect two 4 Mbps SDSL for flow)  The RV082 can do?

  Best regards

  You would need a RV016, who takes in charge up to 7 WAN ports. RV082 has only two WAN ports.

• error on the remote desktop and VPN connections

  Unable to connect using desktop remote or VPN. remotes can't find the computer at home on the network and the VPN gives me an 800 error code. I used the remote desktop, but it says my work computer isn't on this network and the VPN connection fails. We checked everything using remote assistance, but it becomes too hard and not responses. Help!!!!!!!!!!!!!!!!!!!

  Hello

  Your question of Windows 7 is more complex than what is generally answered in the Microsoft Answers forums. It is better suited for the IT Pro TechNet public.
  Please post your question in the TechNet Windows XP category.
  Here is the link:
  http://social.technet.Microsoft.com/forums/en-us/itproxpsp/threads
   
  I hope this helps.
  Thank you, and in what concerns:
  Shekhar S - Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.
  If this post can help solve your problem, please click the 'Mark as answer' or 'Useful' at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• Win 7 remote desktop and Local printing does not

  I cannot using the network printer locally when I use remote desktop to connect to a Vista computer.  Tab resources for RD, I checked the printers.  The only thing I can understand is that my local network printer, not directly connected to my machine.  Whenever I try to print over my remote desktop session, I can not access my local network printer.

  I installed the printer drivers on the remote computer and when I try to locate the printer, I get the following error message: "Windows cannot connect to the printer.  Print Server Spooler service is not running... "but the spooler service IS running Board.

  Any advice would be greatly appreciated.  I spent a few hours on this one and am at a loss at this point.

  UPDATE: I tried to connect my printer to the local USB port this morning.  Still would not work.  I get the same error of queue.  The drivers are not corrupt, as others have indicated may be the cause.  They work very well on my system locally with 7.

  I also found a post elsewhere that he issue 'sharing permissions' and 'network permissons' setting to resovle the spooler error.  Still no go.

  Help, please.  I really need to print locally.

  I finally have figued try after four days and many hours on the phone with Microsoft.  Microsoft said it was related to my router settings, but I didn't believe it because the remote computer has seen my iPhone very well when it was connected locally.  After just playing, here is what I found... it was pretty basic!

  On the remote system, when you try to add a 'local' printer, it has a drop-down list with a list of local ports who sees your system remotely.  Some of those who will be on the remote system, but others will be on your local system.  Take note of those that are visible on your local system.  In my case, LPT1 was not visible, but was COM3.

  Then, on your local system, in the settings of your printer works (printer, Ports tab properties), there is a checkbox indicating "Enable Printer Pooling."  When you check this box, you can select multiple ports on your local computer.  Here, you must check the box that shows your remote system (in my case, this is COM3), but make sure your exisitng port is checked as well as (in my case, an IP port for my wireless router).  Basically what you do is on your local system, you are pooling your installation existing printer with a port that can be seen by your system remotely.

  Then, on the remote system, install the printer drivers, but do not select a port.  Then go to printers and add a printer.  Select 'local' facility for whom and when asked for the port, use the port that you checked in the previous step on your local system (in my case, I chose COM3 on my local system).  Select your printer from the list.  It will ask you if you want to use the existing drivers... say Yes.  Print a test page to make sure it works.  Worked fine for me.

  I can simply not believe how obvsious this solution has been!  If the remote system is unable to see the port that you are using currently, pool your configuration with a port that he can see!

• Connection remote desktop and printing problems

  Hello

  I use Windows 7 on my desktop and also connected to Windows Server 2008 R2 to run applications in Windows Server. However, I have noticed there is problem with printer problems. Sometimes, when I tried to print some documents with applications in Windows Server with my printer in my room, connected to the desktop computer, it won't work.

  Besides, I need to go to Windows Server, restart the Printer Spooler Service component, so it does not yet. It is a pain.

  I also noticed there is to wait about 30 seconds to process any document to print.

  Unlike if I print documents directly from my local desktop computer that is running Windows 7 and is connected to a local printer, it takes seconds to print.

  My office is connected to Windows Server 2008 via LAN. I wouldn't have such a significant delay in printing.

  I also wonder why Printer Spooler needs to be restarted when the printer does not work.

  Can someone advise me on this? Peut - what Microsoft looks at this problem and release updates to fix the bug to improve the system?

  Thank you

  Kind regards

  Clement

  Hello Clement,

  Welcome to the Microsoft Community Forum.

  The question you posted would be better suited to the TechNet community.

  Please visit the link below to find a community that will support what ask you:

  Microsoft TechNet

  http://social.technet.Microsoft.com/forums/Windows/en-us/home?category=w7itpro

  Hope the helps of information. Let us know if you need help with Windows related issues. We will be happy to help you.

  Thank you

• Cisco Small Business Equipment VLAN security issue

  Hi, I have a RV220W router and a switch SG200-18. I'm trying to set up my network to be as secure as possible...

  The RV220W has the configuration of VLAN next:

  Port 1: Manage, DMZ, Business, Test, Diag, home and anywhere (not identified)

  Port 2-4: not used (unidentified) and people with DISABILITIES

  All ports were excluded from the default VLAN

  SG200-18 has the configuration of VLAN next:

  Port 1 (trunk): manage, DMZ, Business, Test, Diag, home and anywhere (not identified)

  Port 2-17 (access): not used (unidentified) and people with DISABILITIES

  Port 18 (access): manage (unlabeled) * used to configure and manage the switching and routing of a pc

  All ports were excluded from the default VLAN

  I installed this according to the instructions in the Cisco security best practices: http://www.cisco.com/warp/public/cc/pd/si/casi/ca6000/prodlit/vlnwp_wp.pdf

  My questions regarding my network of quenching of Double-Encapsulated 802. 1 q / attack of VLAN nested. The white paper suggests to disable the VLAN native/unidentified all trunk ports... Unfortunately the RV220W seems to require a VLAN without label on each port (won't allow me to only have the tag VLAN)... Can someone suggest a more secure configuration given that I work with?

  Thank you!

  P.S. the switch allows me to configure a port mode 'General' where I can configure the frame Type to "Admit tag only" to allow only traffic labeled... I don't know if this would increase security?

  In what concerns the vlan tag/UNTAG Yes. You must take into account the limitation of the router.

  -Tom
  Please mark replied messages useful

• 6.0 CSA remote desktop and

  I upgraded to 6.0 CSA agent on my PC and when I try desktop remotely to a server, I am not able to. I looked in the newspapers of the CSA and there is not a log message that indicates the action was blocked. I uninstalled CSA and I am able to RDP. All the world experience, and is there a way around it?

  There is no event in the management console as well.

  Thanks in advance!

  With CSA 6.0, network access control rule [1635], were decisive for this access. The request is identified as:

  svhost.exe k termsvcs

  Termsvcs is your terminal services/RDP. Just add an exception to this rule that allows the connection using the host addresses.

• DHCP SNOOPING TO THE SWITCH OF CISCO SMALL BUSINESS SF200-48

  Please help me. I need to know if the dhcp snooping is available in cisco firmware version 1.3.7.18.

  Hi Bonnie, as I know DHCP snooping is not on the SX200 switch. I am also unable to find documentation in Administrator's guide and release notes not stating that it is.

• Gateway to Comcast Business class SMCD3G-CCR and Cisco 2960 G switch

  Hello

  I'm looking to upgrade my silent switches to a Cisco 2960 switch.  I wanted to check and make sure that this configuration would be funded.

  I need to configure the 4 VLANS on Cisco 2960 switch, 1 for the vmotion traffic, which would have no internet access, one for management traffic that does not have internet access, for standard server traffic and traffic vmserver, who should access to the internet.

  The Cisco switch working with gateway SMCD3G-CCR ok, or do I need another router for this?  If yes why?

  I don't know if this is the right forum but I know that Cisco linksys bough, so I hope someone can point me in the right direction.

  Thank you

  Hello.

  These products are processed by the Cisco Small Business Support Community.

  * If my post answered your question, please mark it as "acceptable Solution".

  Thank you!

• I have two monitors, I need remote desktop for my computer at home and be able to see two screens on my home computer, how do I do this?

  I have a laptop with a single monitor.

  I need remote desktop for my computer at home and be able to see two screens on my computer at home.

  How do I do that?

  Original title: dual monitor question

  If you look at 'Options' remote desktop and look at the "View" tab there is a checkbox for "use all of my monitors for the remote session.  You may need to be an administrator to set this option.

  Check out these similar posts too.

  http://www.Google.com.au/search?q=remote+desktop+dual+monitor&SourceID=IE7&RLS=com.Microsoft:-to THE: IE-address & ie = & oe = & redir_esc = & ei = WgtJUKLeH6mRiQe834DoAw