Configuration of VLAN Tagging

Similar Questions

• Need help to configure the VLAN on a powerconnect 5448

  Hello world

  I am currently working on 2 switches PowerConnect 5448 but I'm completely lost in configuring VLAN.

  My bow:

  

  My needs are:

  -J' have 2 different networks that need to be isolated in different VLANS

  -I want to port 11-14 to use for network backup, all others must be used for the production network.

  -This 2 networks must pass through the port 48 (fiber)

  How can I configure this kind of network on the powerconnect interface (or via telnet)?

  My understood are the following, I have to create 2 different VLAN tag all ports, switch to safe mode all ports of the entitlement each port to the VLAN voted. Am I wrong?

  How the fiber port?

  Thanks in advance for your help on this matter.

  Since your 2 VLAN need not communicate with each other, you should be able to get this working.

  The easiest way to do this would be to have your production on VLAN 1 and VLAN 2 second network.

  Assign an IP address to the switch with the command IP #.

  Assign a default gateway with the # ip default-gateway command.

  Create a VLAN 2:

  Database console (config) # vlan

  Console (config - vlan) # vlan 2

  Set 11-14 ports to access the mode for VLAN 2

  Console # switchport mode access

  Console # switchport access vlan 2

  Set 48 on trunk or general mode ports.

  Console # switchport mode Trunk

  console # permit trunk switchport vlan add 2

  You should get pretty close to a work environment. You may encounter some problem with VLAN 2 contacting 192.168.1.0, maybe just need to put it up and test.

  Here are a few links to software packages and manuals that can help.

  Firmware.

  http://Dell.to/1tz8tW0

  Manuals.

  http://Dell.to/1yqV4DJ

  Keep us on how will your configuration.

• PowerConnect 5448, how all the trunk of physical ports and allow all the VLAN tags to pass transparently

  I would like to achieve such a goal, do all acts of switch ports 5448 as 'trunk', that is, just as an entry-level switch. Yes, I want all the tags VLAN through seamlessly.

  Let me explain more clearly. If

  • With MAC1 PC1 is connected to switch port 1 (port 1) in short, PC2 with MAC2 is connected to port 2.
  • PC1 sends a packet with vlanid = 30 ethernet VLAN tag,.

  I want the ethernet packet must be SENT to port 2 without modification, i.e. 2 PC will receive the package with exactly the same byte packets that PC1 sends.

  Currently, I want to configure all ports from the switch to act like this, but how to do this? Can someone tell me the more concise CLI commands to achieve? Alternatively, it is possible via the web interface?

  I must again complain the poor manual, which talks about this concept and this notion over and over again (both of ambiguous statements that the author of manual does not), BUT doesn't explain them not at the level of the content of the packages, so I'm totally at a loss.

  I tried the web interface. Simply together port 1 and 2 for access mode or general mode does not work.

  Please help me. Thank you in advance.

  Thank you, Josh, you begin to point me in the right direction.

  Now, I know just affecting a Trunk port, or general mode is NOT sufficient.  I have to give what kind of package VLAN (i.e. what VLAN ID) are allowed to pass through.

  To do this assignment, I have to take 2 steps. say first of all, the database "vlan" to recognize a VLAN ID in the world, then say that some specific port is allowed to pass through with this VLAN ID specific packages.

  Thus, in order to pass packets VLAN with VLAN ID 18-25 no modified (marked packets in packages marked on) g7 to the g8 to port port, I have to do:

  Console # config
  Console (config) # vlan database
  Console(config-VLAN) # vlan 18-25
  Console(config-VLAN) # exit

  Console (config) # interface ethernet g7
  Console # switchport general mode
  Console # switchport General allowed vlan add the tag of 18-25

  and again for the g8. And if I want to 48 ports to act like that, I have to write this kind of order 48 times right? All the shortcuts?

  Some useful links for me: http://hasanmansur.com/2012/10/14/powerconnect-switchport-modes/

• PC6224 Configuration of VLAN

  Hello

  I am desirous of VLAN my iSCSI data in two separate VLANS and think I understand what to do. I would like to just anyone for the validation test it before I go live and eventually get things horribly wrong.

  

  All i15 labeled ports must be configured as switchport access vlan 15
  All i16 labeled ports must be configured as switchport access vlan 16
  Four XG ports must be configured as vlan allowed switchport General add 15.16 tag.

  So far I think I have it but I'm not sure on how to get the traffic untagged crossing ports XG.
  It will do it automatically, or should I set switchport General pvid 1 for these ports, so all untagged traffic goes to the network vlan by default?

  I need to set the VLAN on LAG3 or will it not serious because the ports are marked? Or do I not have to label the ports if the OFFSET is the tag? Or I have to mark the two?

  Thanks for the help,

  Jim.

  Put a PVID on a LAG sets going what traffic VLAN not identified.

• ISA550W with multi SSID (each having separate DHCP and VLAN tag)?

  ISA550W can do the following (in order):

  (1) first group interfaces physical and Wi - Fi SSID (s) set

  (2) then assign with DHCP (ip or subnet)

  (3) then add a tag VLAN interfaces and SSID (s) wireless

  (4) repeat 1 to 3 for the remainging and SSID (s) wireless interfaces to create the following diagram:

  

  (1) I believe that could transform these ports in ports of junction. That said, I'll normally in the ports themselves through networking, change them to the Trunk ports and add the appropriate VLAN. Please keep in mind that as a general rule which present you to a Trunk port is another switch. Then you EF the VLAN appropriate to each switch coelio that attach a device such as a workstation. There are some devices that do not support be connected to a Trunk port, like the OnPlus of Cisco device however.

  (2) think SSID that only access ports. Because you could never connect a device that would support Trunking wireless, you can apply only 1 VLAN by SSID wireless-> basic settings.

  (3) because the SSID cannot be interconnection. See #2 above for configuring the VLANS on SSID.

  Sent by Cisco Support technique iPhone App

• Configuration of VLAN Switch SF302 - 08 p

  I have the following Setup using two switches PoE SF302 - 08 p:

  1st floor

  =========

  SWITCH1 # <------->private network

  <------->public network

  2nd floor

  =========

  Switch #2 <------->private network

  ... public network (visible, but devices can't connect)

  I tried to do the config in the identical to the #1 switch #2 switch, but something still does not work.

  This is probably a configuration issue VLAN, or what?

  Thank you.

  Ken Watkins

  Hi Ken, the interfaces between switches must both vlan of the port.

  example of

  VLAN 1

  VLAN 2

  port 1 connects to port 1 of the second switch

  config t

  interface gi01

  switchport mode trunk

  switchport trunk allowed vlan add 2

  The ports between switches must be vlan unidentified native, all other VLAN Tag. In my example, 1u, 2 t.

  -Tom
  Please mark replied messages useful

• VLAN tagging on VIC 1225

  Hi community

  We are currently developing a standalone Server, installed c240 with a vic1225 (connected to a pair of vpc 5500 nexus).

  We have bare metal windows 2008 R2 os installed and active nic teaming ((802.3ad) with the enictool.)

  Now we want to Setup vlan tag NICs in windows, but there is no way to do...

  This is usually possible in windows 2008 Server?

  THX in advance for advice.

  Hello

  ENIC pilot for W2K8 does not support feature of 1 q VLAN dot.

  With W2K12, the grouping of the characteristic marking windows native driver.

  Alternative options are

  (1) implement adapter FEX

  (2) If you plan to run Hyper-V on the host, it can mark the VLAN.

  (3) implement individual vNIC for each VIRTUAL LAN and configure the host of active transmission load balancing / active. In addition, configure links on the individual switch ports allowing to the VLAN needed and have them not as a port-channel / vPC

  I recommend you to upgrade the firmware and drivers to the latest version to eliminate known issues.

  Padma

• Configure the vlan with SG 300 - 10 p and 520 SA

  Hi all

  Forgive my ignorance, but I need help with the basic configuration.

  For a small office, I bought an appliance of security SA520 (for future VPN with another remote desktop) and a switch of SG 300 - 10 p to connect 3 PCs and 3 IP PHONE. The SA 520 is the router. I have to configure 2 VLANS on the switch:

  VLAN2: DATA (for PC)

  VLAN3: VOICE (for IP PHONE)

  VLAN1: BY DEFAULT.

  How can I configure simply all ports?

  I would like to configure ports 1-4 on 5 to 8 ports and VLAN2, VLAN3 and G10 port is reserved for the SA520 router.

  I want to split VOICE and DATA network.

  I think I need to create a trunk on G10 to SA520...

  Can someone help me?

  Hi Julien,

  OK sounds like you use it vlan by default for network management and the vlan 2 for vlan3 for voice and data.

  I use a calculator for this, my SA520 is ready at the present time.

  Step 1   On the SA520 add vlan 2 and vlan 3 and label them voice and data respectively.

  

  Step 2. Allows you to use the switch port 4 on the SA520 as a port to shared resources to the SG-300.

  (my intent is to use vlan1 not tagged vlan tagged 2 and vlan tagged 3 on the uplink of the switch and the SA500.)

  To do this, I have to say the SA520 port 4 of the switch will be in trunking and not access mode.

  

  You will need to check the membership of vlan 2 and vlan 3 on switch port 4.

  Step 3.  Now add a few IPS to VLAN2 and VLAN3

  Step 4.  Create DHCP scopes if that is what is needed on the SA520

  

  So now I hope that we have the SA520 with the associated IPS VLAN1, VLAN2 and VLAN3

  We also have the switch port 4 as a network interface

  We are vlan1 reproducing unidentified and vlan2 tag and tag to the SG-300 switch vlan3.

  We do the opposite on the SG-300 switch.

  If you use G10 as the uplink to the SA520 you'll notice of default port 10 must already be in trunk mode.

  Switch ports G10 should be marked for vlan 2 and labelled for vlan3.  It will be, default Gi10 untagged for vlan1.

  Make sure you keep ports switch is correctly set up.

  Best regards, Dave

• What configuration of VLAN requires a switch connectivity defined as an access port?

  What configuration of VLAN requires a switch connectivity defined as an access port?

  By external switch tagging

• With the help of VLANS and VLAN Tagging is not working / no connection

  Hello

  I m trying to configure a VLAN between some virtual machines on ESX host 3.

  I want to do this way:

  http://KB.VMware.com/selfservice/microsites/search.do?language=en_US & cmd = displayKC & externalId = 1004074

  I got 1 dedicated NETWORK adapter to each ESX host that is connected to a dvSwitch in which I configured a portgroup

  with VLAN ID 2121. I have configured each virtual machine to use this network.

  When I put the virtual machines on a single host, they are able to communicate.

  When they are placed on different hosts they are (if the VIRTUAL LAN is enabled on portgroup) not able to communicate.

  So I m assuming it must be a problem in the config NIC on the ESX host or switch.

  I m using a HP2910AL on which I activated mode trunk for each port that is connected to a NETWORK card with

  the dvSwitch/Portgroup I try to use for the vlan. In the hp switch, I have a default VLAN with ID 1 where

  the Ports are marked not signposted. I install a second VLAN on the switch with ID 2121 in which I scored

  This tag ports.

  Is there something else to do - perhaps side ESX host?

  I tried changing the settings as "forged transmission-> allow ' on portgroup and I found other things

  in the web, but always without success.

  Kind regards

  Patrick

  Were you referred to this guide? :

  http://CDN.ProCurve.com/training/manuals/2910-ATG-Feb09-2-VLAN.PDF

  "show vlan ports" would be my next check to make sure that you have connected to your ESXi host 3 ports in the vlan 2121.

  As Duncan has said if you have a VLAN ID on the portgroup in the vSwitch and you have the port on the pSwitch as trunk not acess and VLAN ID is allowed on the trunk port pSwitch you should be ok.  Just to clarify the trunk is 802. 1 q No 802.3ad.

  The reverse is not VLAN ID on the portgroup vSwitch, use coelio on pSwitch with VLAN ID.  Limited pSwitch port to a VLAN, this may be ok for you?

• VLAN Tagging (VST) and VLAN native on the same vswitch

  I'm trying to figure out if its possible to put running the VLAN tagging for a vswitch if our virtual machines are currently in the vlan 1 (vlan native) on our cisco switches. I don't know why it's set up this way, but change is not an option at this time.

  Ultimately what I'm trying to accomplish is setting up a group of servers that differ on one VLAN, but under the same vswitch. I'm assuming that VST is what I need, but I don't know if I can simply specify how vlan 1 as the vlan 1 is not marked on cisco switches and my understanding is that VST requires to carry a label.

  Your help is greatly appreciated.

  NuRD.

  With the vSwitch connected to a trunk on the physical switch port, create the port groups and you need only configure the ID then VLAN for the port groups that do not use of VLAN native. See for example http://kb.vmware.com/kb/1004074

  André

• Several Vlan tagging to vswitch

  Hi I have abt 20 vm in an ESX 4.0 each with different vlan and all the virtual machine cannot see each other what would be a better approach for this configuration. create a virtual switch for each computer virtual but with different vlan tagging assign each? (virtual switch 20 sense) or use pvlan a better option for this I only got 2 physical cables connected to this esx carrying all the traffic 20 vlan. Or any other recommendation?

  Thanks for any info

  sounds odd humm maybe these articles can help you:

  http://communities.VMware.com/docs/doc-4861

  http://KB.VMware.com/selfservice/microsites/search.do?language=en_US&cmd=displayKC&externalID=1004887

  Alex

• Issue of configuration of VLAN

  We have ESX Server 3.5.0 110181 and VIC version 2.5.0. Each of our ESX host has 4 NICs for use in our LANs, 2 more for each Port of the Console of Service VMKernel Port. Physical network adapters to connect to a stack of 5500 Nortel ethernet Routing switches.

  I am trying configure 4 NICs in each ESX host to be able to view the two VLANS separated. I am trying to configure these VLANS on the Nortel switches. The problem is I'm new on the VLAN and can't do network cards in the ESX host to always see the two VLANS. Right now I have an ESX host with two network cards that see both VLAN and two network cards who don't see a VLAN. I'm pulling my hair out trying to figure out what I did wrong.

  First and I realize maybe this isn't the best place to ask this question, but in the Nortel VLAN config, there are four choices of marking and I have not been able to understand that it is appropriate to use for the ESX host. The choices are; Removes all brand, removes the brand only PVID, Tag all or only Tag PVID.  Can someone help me with this?

  Also should I do at VIC or on the ESX host to see systematically the VLAN? The NICs appear to periodically just drag one of VLAN, generally the VLAN the DMZ.

  Any help much appreciated. This VLAN is new to me and I could not find very clear or basic info. on the configuration of VLANS.

  Thank you.

  Hi danzbassman, the best would be to put each of the 4 corresponding ports on your Nortel 'Tag All' or "UNTAG PVID." switch only

  If you use 'UNTAG PVID Only' on the switch, this means that all executives EXCEPT those on the VLAN "primary" assigned to the port should have tags on them. Then, on the side of ESX vSwitch, you want to create your virtual machine with the many groups entered the VLAN ID field for each VLAN "secondary" on the ports of Nortel and the VLAN ID field blank for the VLAN "primary". For example, suppose that your four NICs (attributed to vSwitch1) were connected to ports 1, 2, 3 and 4 on the side of Nortel and you had three VLANS, 100, 200, and 300, with VLAN 100 defined as the PVID on each of the four ports. If you want your virtual machines to be able to properly access to all three of these VLANs, to put in place three groups of virtual computer on vSwitch1 ports, one with the VLAN ID set to nothing (for VLAN 100 traffic, because it is not marked), one with the VLAN ID value of 200 and another with the VLAN ID value 300.

  If you use 'Tag All', then you would follow the same procedure, except your first port group (one for traffic VLAN 100) should also have its VLAN ID set to 100.

  Please, help me by awarding points for a 'useful' or 'proper' response if you think it is useful!

  -Amit

• Need help setting up a configuration of VLAN special using WRVS4400N

  Hi guys,.

   

  I need your help on how to implement a configuration of VLAN somehow non-standard.

  The situation is the following:

  The customer wants a WLAN set up for the company and the other for guests. Now, wouldn't that be not so difficult if we'd be using the internal internet connection. But the WRVS4400N will be used to implement wireless LANs / VLAN only.

  The company uses the DHCP protocol on both of their subnets, provided by a Watchguard Firebox XTM510.

  

  Now, what we would do is set up the back door #1 for the connection to the subnet of the client and the #2 for the connection to the optional subnet for the guests. The first problem is that we were not able to configure DHCP forwards to the VLAN2. It works very well on the 1st but the 2nd doesn't allow that either ENabled or disabled, grayed out DHCP.

  To work around the problem that he would be allowed to set up DHCP WRVS4400N providing in itself for the subnet invited, but try that didn't work at all.

  Is it possible? Thanks in advance!

  Best,

  Ralph.

  
  

• RVS4000 Configuration of VLAN

  I am trying to set up a couple of VLAN on the RVS4000.  The router allows me to enter the VLAN ID without problem, but it doesn't seem to be a screen to set up the network and DHCP component for the new configuration of VLAN.  I saved the configuration of the router and printed.  There are several VIRTUAL networks in the configuration with the IP addresses starting with 192.168.2.0/24 and increasing unit (192.168.3.0, 192.168.4.0, etc.).   These networks VLAN contains the DHCP configuration also.  How can I change these addresses.  Is it possible that you can not change them and take what's there and use it?   When I configured a VLAN with ID 30, is to tie the knots got an address in the 192.168.2.0 subnet, which is not what I wanted.  The manual is no help.  He said almost nothing about the configuration of VLANS.  Is there another source for more information on the configuration of the RVS4000 with VLAN?

  Also, I downloaded and installed the new firmware for the router.

  Any help is appreciated.

  Tony

  Forget it.  I thought about it.  It is on the configuration page and you will need to use the drop-down list for the VLAN configured.