Connect the monitor to the laptop with displayport/DVI

Similar Questions

• When I try to connect with my wireless laptop will connect only to Local access. If I connect the laptop to the router with the ethernet cable, it works very well.

  VIsta - Local access only

  HI -.
  I recently moved.   I use the same router from my old apartment and I had no problem connection in the past.   Since I moved I have a new Time Warner modem (Cisco) and the modem works fine.

  The router also works very well I'm able to connect with my iPhone and IPad without any problem.

  But when I try to connect with my wireless laptop, it will only connect to Local access.    If I connect the laptop to the router with the ethernet cable, it works very well.

  It's a Dell Studio 15 with Vista.

  The computer is able to connect to wifi to other places without any problem, but for some reason that I can't connect home.   I tried to reset the modem and the router several times, but that did not help.   I tried the option repair & diagnose several times but it doesn't work.

  I tried to look for other solutions online and tried to disable IPv6, and while it helped some and I was able to connect wireless, the computer ran so slowly that it didn't seem like a good solution.

  This has been very frustrating.   Thanks in advance for any help or suggestion.
  Staci

  Hello Staciusa,

  Have you tried to change the wireless channel that your router is running at? There may be interference that could prevent the internet connection:

  Take a look at step 6 in this article that give more details about it:

  http://www.Microsoft.com/athome/Setup/wirelesstips.aspx

  If you need assistance to change the settings of the specific router, you will need to contact your router manufacturer or your internet service provider.

• My date and time settings are set in Egypt and whenever updates of the laptop with microsoft server time, it increases of 1 h.

  My date and time settings are set in Egypt and whenever updates of the laptop with microsoft server time, it increases of 1 h.
  Recently in Egypt, changes of daylight has been cancelled and I guess that's the cause of the problem!
  Any ideas?

  If time was recently cancelled, you can go to your control panel:
  Panel-> data and time-zone (tab) >
  and uncheck the "automatically adjust clock for daylight saving time.

  Otherwise, you probably need to adjust your zone settings on your computer using Microsoft time zone Editor.

  TZEdit: <> http://download.microsoft.com/download/5/8/a/58a208b7-7dc7-4bc7-8357-28e29cdac52f/tzedit.exe >

  HTH,
  JW

• I just bought a PC C50 toshiba laptop with windows 10. I would like to ask if someone can tell me if it is easy to remove the Windows OS 10 and restart the laptop with my windows disc 7.

  * Original title: delete windows 10

  Hi, I just bought a PC C50 toshiba laptop with windows 10. Is not not a geek, I would like to ask if someone can tell me

  If it is easy to remove 10 OS and restarting the laptop with my windows disc windows 7, the reason why I want to do is

  because I have aready have a desk top running 7, but it is to the top at the moment and could use the laptop backup

  You must ask your win-10 computer make this question

  They would have made drivers for this machine for win - 7

  If not then no.

  Your only option is to return it and ask for a unit that has win 7 drivers.

• A box appears whenever I start the laptop with the word CyHidWin to the top.

  Original title: CyHidWin

  A box appears whenever I start the laptop with the word CyHidWin to the top.  I don't know what it is.  I can't cut, max, delete or move.  It covers my icons... no one knows what it is and how to get rid of?  I got this laptop for 7 months and most of the time that this box comes up.

  original title: CyHidWin Popups on every reboot.

  Hello

  -Were there any changes made to the computer before the show?

  -What is the brand and model of your computer?

  I would suggest trying the following steps and check if it helps.

  Method 1:

  To help resolve the error message, you can start Windows Vista or Windows 7 by using a minimal set of drivers and startup programs. This type of boot is known as a "clean boot". A clean boot helps eliminate software conflicts.

  How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7

  http://support.Microsoft.com/kb/929135

  Please note: After troubleshooting, be sure to start your computer in normal mode by following step 7.

  Method 2:

  I suggest you run Microsoft Safety Scanner to make sure that your computer is virus-free.

  http://www.Microsoft.com/security/scanner/en-us/default.aspx

  Safety Scanner WARNING: There could be a loss of data while performing an analysis using the Microsoft safety scanner to eliminate viruses as appropriate.

  Hope this information is useful.

• Can I install Acrobat 9 Standard on the laptop with Windows 10 operating systems?

  Can I install Acrobat 9 Standard on the laptop with Windows 10 operating systems?

  Hi derrickt92250579 ,

  Acrobat 9 is not compatible with windows 10.

  You can check this link to check the system requirements: Adobe Acrobat required configuration

  Let us know if you need additional assistance.

  Concerning

  Sarojini

• How to connect the Ombudsman with several bpel process

  Hi Please someone tell me how to connect the Ombudsman with several processes bpel in soa 11g

  And here

  http://eoracleapps.blogspot.com/2009/11/how-to-call-synchronous-BPEL-process.html

• Connect two monitors to my laptop HP

  I have a laptop dv7 HP Envy.

  Windows 8.1

  Inter Core i 7-3630QM [email protected] GHz

  16 GB of Ram

  64 bit

  1 TB HD

  Intel HD Graphics

  NVIDIA GeForce GT 635 m

  2 monitors:

  HP w2207h W? : 1 - HDMI. 1 VGA & 1-USBin.

  2 - Out USB

  Monitor 27 '' LCD HNC

  HDMI 1

  HDMI 2

  VGA

  I would like to connect two monitors to this laptop. The laptop has: 1-HDMI; 1 VGA.

  This seems to be a slam dunk, it's not. They put the VGA and HDMI so close together that I can't connect both at the same time. It's as if they force the VGA or HDMI. I am a general contractor and need two monitors if possible. I look at work photos on an all in utiizing a drawing program to produce plans of work on another.  There are 1/4 "between the VGA and HDMI imput plugs I would have been Golden, but they did not. Can anyone suggest a way to get these two monitors plugged and upward and running.

  Thank you

  Perrys6

  Ahhhhhh.  Hey all what works.  I had not thought that.

• I have a problem with the connection of the laptop with the LCD.

  I'm trying to connect my laptop with a cable adapter VGA - HDMI to a LCD to watch my PC to TV programs but I don't get the window to duplicate the monitor and apply the correct resolution.  How can I solve this?

  Don't forget to press the FN key and screen switch on your laptop to an external monitor/tv/projector keyboard.

• My sister has problems on his laptop, how can I connect to the laptop with my labtop to help him with his computer problems? Thank you.

  My sister has problems on his laptop, how can I connect to laptop with my labtop to help her with her computer problems when I live several States away? Please help me if you know how to do this thank you.

  Suggest you use Team Viewer, free version.
  It is used here every day for several hours.

  Please see the links below for more details...
  http://www.TeamViewer.com/en/index.aspx
  http://www.TeamViewer.com/en/products/remotecontrol.aspx
  http://www.TeamViewer.com/en/help/cat15-remote-control.aspx

• Printer LaserJet 4100: Should which cable I for Laserjet 4100 connected to the laptop with USB port

  I have the HP Laserjet 4100 printer. I bought a new laptop with USB ports.  What type of printer cable I need to connect the printer to my laptop? Is there some kind of printer cable adapter, or something else that will do the trick?

  I have the same question about my HP Laserjet 1100 printer.

  Thanks in advance for your assistance expected.

  If I remember correctly, the 1100 uses a cable "C", alias MicroCentronics.  Have never seen an adapter for that one.  On the 4100, you can get a USB to parallel adapter.  They are pretty cheap and available at most CESS (Consumer Electronics Super Store) as Best Buy.  Staples and OfficeMax/Office Depot should also wear.  Online is cheaper if you have time to wait.

  The thing with these USB converters is often must 'install' the cable first.  In other words, connect it to the laptop, then wait so he could install, then connect the printer.  Depending on your operating system and if you have correct updates that can be almost instantaneous, and you may not even see it pop on the screen.

  Best idea is that since these are obviously not portable machines, connect them to your router via a network card.  I had the 1100 years and used a cheap 170 X.  I know most recent are available which are faster.

  For the 4100, see if you can retrieve a Jet Direct 620 unit on eBay.  Probably less than $50 and sometimes even as little as $25.  Stay away from the 600, 510 or 615 cards.  Low or as the 600, they can leave your network open to hackers.  No need to get Gigabit cards as they will be well above what the 4100 can handle.

  Now, two of these old devices, processing power and memory can be a problem.  Never try to print documents online.  Save them on your laptop, and then print.  You will probably get communication errors if you print directly from IE or FireFox.

  If the 1100 does not die, not even worth fixing.  Put into a Fuser is a nightmare.  The 4100 will probably work for another 20 years if you keep to clean and replace the rolls before they cause jams.

• Printer on Windows 7 PC, unable to connect with the laptop with Vista

  I have a Lexmark 2600 Series printer on a Windows 7 32-bit computer.  I am not able to connect to the printer with Vista laptop for my wife.  I can share files and see the printer.  I try to connect and I get "Windows cannot connect to the printer. Impossible operation completed (error 0x000003eb). "I tried to install locally and change the path without success.  Any help would be much appreciated.

  Hi Zyfot,

  First of all, I would say that you add the printer on the vista computer and check.

  1. open Printers by clicking the Start button, clicking Control Panel, hardware and soundand then click Printers.
  2. click on Add a printer.
  3. in the Add Printer Wizard, select Add a network, wireless or Bluetooth printer.
  4. in the list of available printers, select the one you want to use, and then click Next. If your computer is connected to a network, only printers listed in Active Directory for your domain are displayed in the list.
  5. If prompted, install the printer driver on your computer. If you are prompted for an administrator password or a confirmation, type the password or provide confirmation.
  6. follow the steps in the wizard and then click Finish.

  Install a printer on a home network
  http://Windows.Microsoft.com/en-us/Windows-Vista/install-a-printer-on-a-home-network

  Network printer problems
  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-network-printer-problems

  Also, make sure that the print spooler service is running on the windows vista computer.

  A print spooler is the service that temporarily stores the disk printing hard or in memory until the printer is ready to print.
  You must be logged on as administrator to perform these steps.

  1. open Administrative Tools by clicking the Start button, then Control Panel. In the search box, type Administrative Tools, and then click Administrative Tools.
  2. double-click on Services. If you are prompted for an administrator password or a confirmation, type the password or provide confirmation.
  3. right click on the print spooler service, and then click Properties.
  4. under the tab general , next to Startup type, make sure that Automatic is selected.
  5. If the service is not already running, under Service status, click Startand then click OK. If you are prompted for an administrator password or a confirmation, type the password or provide confirmation.

  I hope this helps!

  Halima S - Microsoft technical support.
  Visit our Microsoft answers feedback Forum and let us know what you think.

• Connect the TV (with sound) and monitor for Optiplex 390

  Here is my system info:

  OptiPlex 390 small footprint

  Windows 7 64 bit

  Intel Chipset H61

  Intel HD 2000 (with HDMI and VGA) graphics card

  Map of AMD Radeon 6350 512 MB video (with 2 DVI splitter)

  I need to connect 1) HD TV with the sound via HDMI and 2) monitor via VGA to this system (no sound).  I did a lot of research on the Internet but can't find a definitive answer if my system will support both views.  Can anyone confirm if one of the three options below does not work, or any other ideas?

  Option 1: remove AMD card, connect the HDMI TV, connect the VGA monitor.  I've seen conflicting information if the HDMI and VGA ports can be connected at the same time.

  Option 2: Connect TV: dispatcher--> DVI HDMI adapter DVI-->--> TV, monitor connect a HDMI cable: dispatcher DVI DVI VGA adapter--> monitor-->.  It should work, but if someone can confirm if the AMD Radeon 6350 supports audio through DVI to TV?

  3rd possibility: buy another video with HDMI and VGA card.  I'd rather not spend more money... I have six systems to connect!

  Thank you in advance for your help!

  Hi Ozone72,

  Intel HD Graphics 2000 which was shipped with OptiPlex 390 supports two independent screens. Which means that you can connect TV for VGA and HDMI monitor, so that AMD card must be removed from the computer.

  Please try it and return back if it worked.

• How to connect the laptop screen to two different TVs?

  I try to show what is on my laptop two two different TVs at the same time. I already have the hdmi cable connected, but I can't seem to find a way to show my monitor on both screens at the same time. I can get it to show on one or the other. Any suggestions?

  Thank you
   
  Original title: connection screen of the laptop to two screens

  Hi GabrielGomezYZ,

  Thanks for posting your question in the Microsoft Community Forums.

  You have a problem with the display of the content on the laptop on more than one TV. It can be difficult when something that is important to you does not work as expected. It's pretty simple and we're here to help you solve the problem. We work as a team and get this sorted out.

  Method-

  I would have you look at the article-

  Setting up dual monitor: two screens are better than one

  http://www.Microsoft.com/athome/organization/twomonitors.aspx#fBid=DT7eyPCoaLh

  In addition, you can check the items of reference-

  Work and play better with multiple monitors

  http://Windows.Microsoft.com/en-in/Windows7/work-and-play-better-with-multiple-monitors

  HDTV: Frequently asked questions

  http://Windows.Microsoft.com/en-us/Windows7/HDTV-frequently-asked-questions

  We know if you need help. We will be happy to help you. We at Microsoft, strive for excellence and provide our customers with the best support.

  Thank you.

• Satellite 2450: How do I start the laptop with the lid closed (LCD).

  I have connected the switch of power with cables and stretched it out and it works fine.

  My question is how can I start the computer with the lid closed? Is there a switch that allows the computer to know when the lid is closed or not? Can I remove this? where is this switch?

  This option can be disabled threw the bios of the computer and how?

  Any help apreciated

  Well, you should be able to boot up your laptop in this way, but how to market? The power button on my laptop is under the cover.

  And Yes, there is a kind of switch, which leave the phone know that the door is closed, but it's only important in Windows, it does not close or go on stand-by.

  To avoid this, just set power options to do nothing on a closed lid.