Connection or cRIO-9073 (soft error)

Similar Questions

• cRIO deployment problem error:-1967357951

  Hello

  When I connect to my cRIO-9073 an error message appear that he could not find any libraries.

  When I ignore it and continue I can't load my VI on the host PC and target in real time.

  I think I installed all the necessary software on the cRIO.

  A description of the problem can be found in the attached PDF file.
  The labview program can be found in attachment.

  Best regards

  Jasper

  Hello, Jasper.

  I've seen this problem before in combination with a problem of memory (availible) on the controller. I see that you have many installed on the controller for cRIO. The cRIO-9073 is around already for a couple of years and is limited in terms of memory avaiable by comparing our new controllers. I noticed you use LabVIEW 2013, which has a larger footprint versions of LabVIEW that where around when the cRIO-9073 saw the light of day. I recommend to format the controller and only install the bare minimum that your application needs for the controller and try again. In this way, we can check if this arrizes cause a memory issue or something else.

  Kind regards

• cRIO-9073 disconnects

  I connected a cRIO-9073 to my computer and connected to my LabVIEW project. I downloaded the software to it and configure it to scan mode. It is, whenever I connect to it in LabVIEW, it disconnects after only 3 minutes exactly. I did nothing at all with it, to make it work, no program or whatever it is. Y at - it software it is absent, is there some configuration details, I am missing or is this possible?

  Martin

  I found the solution to the problem.

  When I format it and install the software on the cRIO-9073 from a computer win Win 7 (64 bit) the communication problem is present. When I install the same software on a computer with Win - XP (32 bit), the problem disappeared. The problem is reproducible.

  Martin

• Unable to create a file with "nidll_vxworks" in Matlab for use with the LabVIEW SIT 2010 and a cRio 9073, error sh.exe

  I am trying to compile an OUTPUT for my Simulink model file by using "nidll_vxworks" and execute it using the Simulation Interface Toolkit for a cRIO 9073. I am able to compile the DLL file by using "nidll" and managed to run the simulation using my PC as a host.

  I have already downloaded the files "gccdist" and "vxworks61gccdist" and copied in "c:" when I build the model in Sumulink I get the following error at the end of the process (at the same time windows tells me that "sh.exe" has stopped working). If it's important, I'm on Windows 7 64-bit, but using Matlab 2009 b 32bits and LabView 2010 32-bit. ANY HELP WILL BE APPRECIATED. "QofV" is the name of my Simulink model and I changed to parts of "XXX" in the path of the file.

  6.1 CCG is only supported on Windows XP.  It is almost indicated in the readme_sit_vxworks.txt found in C:\SimulationInterfaceToolkit\xxxx\VxWorks (where xxxx is the version of the DIS).  It is said:

  * Known issues
  
  ---------------------------
  
  -WindRiver GNU Toolchain 6.3 and 6.1 do not work on Windows Vista.

  To be more explicit, it should be "Vista and later.

  Carl L

  National Instruments

• Deploy the shared target rt variable fails (crio-9073)

  I use a cRIO 9073 with LabVIEW 8.6. I have some variable published to my PC network I want the cRIO host read. However when I try to deploy the variables on the cRIO, I get the following error:

  Initializing...
  Calculating dependencies...
  The checking for conflicts. This may take some time...
  Prepare the items for download. This may take some time...
  Variables variables.lvlib\\129.186.159.84\robot robot deployment deployment has failed (error:-2147220721, (Hex 0x8004030F) the configuration database cannot be opened, perhaps because of corruption.) Note: the steps that you did which led to this error and contact technical support).
  Completed with errors of deployment

  I tried to reinstall the software on the cRIO, which includes the network Variable 1.5.0 engine and tried hosting variables on the cRIO. I still get this error.

  Everyone knows about this problem? What should I do to use variables shared on the 9073?

  I tried stubborn MAX, who did not work. Then I reformatted the cRIO and the problem is solved.

• two flashes on cRIO-9073

  On my new cRIO-9073, the led blinks twice, after that I have (re) software installed on it. The manual says that in this case «the chassis has detected an error in its software to [...]» Reinstall the software on the chassis. I reinstalled three times, each time with success ("congratulations... ("etc. etc.). Originally, there was NEITHER-RIO 3.2 installed on it, but it does not work with my project (I use Labview 8.6), so I had to reinstall OR RIO 3.0 and now I think that there is a compatibility issue beetwen the new cRIO-9073 and Labview RT 8.6 (NOR-RIO 3.0)

  What can I do now?

  Thank you

  
  

• Deployment complete with static Variables cRio-9074 network errors, pc with executable file

  Hello.

  I am building an application runs on a machine without LabVIEW development system and connect via the network shared a cRIO Varibles (RT FIFO). I can successfully create an installer and EXE for PC and a RTEXE for the cRio. When I run on my development computer, the application is able to communicate using variables shared without a problem.

  But, when I install my application on another computer and connect the cRIO, I get the following error when you deploy shared variables when the application starts:

  Initializing...

  Calculating dependencies...

  The checking for conflicts. This operation can take a long time.

  Preparation itesm by download. This operation can take a long time.

  Deployment 169.254.84.198

  Deployment VariableLib.lvlib\\169.254.84.198\VariablesLib (:-2147467259,)

  LabVIEW: Unspecified error (Hex 0 x 800004005).).

  Completed with errors of deployment

  I created an exception in the Windows Firewall configuration. I have included the library of VariableLib on the EXE of RT, outside and inside the exe file to c:\.

  I am downloading the SP1 for LabVIEW and Module RT and decided to reinstall all the software on my cRio.

  Any help will be appreciated.

  Hello Luis.

  Thank you very much for your help. The Variable engine OR has been and should be included in the intallation.

  I was able to get the application running. I installed the System Manager distributed on the PC without LabVIEW to control if the library has been get deployed. Using what I found that another device on the network use the same IP address as the cRio and so the IP address has been lying to the deployment, but the device has returned an error. I just changed the IP address on the cRio and I was good to go. I have not reproduced on both devices such as network shared Variables suggests on some positions, nor I needed to modify the ALIAS files on devices.

  Best regards and thanks again for your time.

• cRIO-9073 only with Labview 8.6? Data record?

  I don't know if you have a special forum for the cRIOS. If so, tell me

  A guys at work told me, he bought a cRIO 9073 two years because he wanted to save the data on vehicles on a USB key.

  He has never had time to work with this thing, after all, and today he asked me, if I can try to get this to work. I had never seen one of those from before, but as far I see this device is no usb port and using the ethernetport to connect to a WLAN-bridge will not work, because when you drive around in the car, you will leave the fast enough network - so I guess the only way to do it might be loggin data in internal memory (128 MB). Is this fair?

  The other problem is, we only have a single license for Labview 8.2 here (the rest is 7.1 )-are there a chance that I can write a Labview program for the cRIO with whom? It is stated in the specifications minimum labview version: 8.6 necessary .

  I can work around that somehow?

  Yes, you need save data on the Flash drive internal, then copy it off the power when you can plug it into a network.

  Write code for the cRIO, you need real-time tools box and perhaps also the FPGA Toolbox.

  If the documentation indicates that you need 8.6 to target the cRIO, then it is you need.  Where did you see that?  I know that 8.5 could target former cRIO controllers, but it is quite possible that 8.6 was the first version with support for this model.

• Why always show that "there is a connection to the Apple store error."? It has been a month I am facing such a problem. How can I fix? Hope you have a solution to this...

  Why always show that "there is a connection to the Apple store error."? It has been a month I am facing such a problem. How can I fix? Hope you have a solution to this...

  I don't know if this is the problem, but it is something that must be correct establish a secure connection:

  Open Date and time preferences system, Date & time tab. Make sure that it is set to automatically set the time.

  Alternatively, make sure that your date/time is correctly set to the second.

  Another thing to try is to restart your modem and router.

• CRIO-9073 is compatible with LabVIEW 8.5.1?

  I just got a cRIO-9073 and a cRIO-9074.

  When I set up, both of them appear correctly in MAX.

  When I add them to a project LabVIEW, the cRIO-9073 does not show the target FPGA. The cRIO-9074 shows.

  I'm using LabVIEW 8.5.1, is compatible with the cRIO-9073?

  Thanks for any help.

  Michel

  Hi Michel!

  According to this link, the interface FPGA and Scan of the cRIO 9073 are only supported in LV 8.6 using the NOR-RIO 3.0 driver.

  The link where you can check the compatibility is:

  FTP://FTP.NI.com/pub/DevZone/tut/crio_software_versions.htm

  Good day!

  Oswald Branford

• FPGA read/write does not not in cRIO-9073

  Hello.

  I'm stuck with a problem in the use of the FPGA Read/Write control please suggest a solution.

  I use cRIO 9073 and I'm trying to place an order ON / OFF of GUI-> RT-> FPGA host. I use a shared variable of the network to transmit the control GUI form to host RT and I use read/write control to FPGA. I also put a Boolean flag in the FPGA VI to control if the control is transferred to the FPGA.

  When I toggle the button in the GUI, I see the same change in the host of RT (shown as 16 probe in attachment 1). However the FPGA indicator (indicated as probe 19) remains the default false state. The FPGA VI is on attachment 2.

  Thank you

  Guilhem

  Your FPGA only reads the control once before entering the loop.  If you want to read control permanently, you must put it inside the loop.

• connection intermittent cRIO (with MAX, etc.)

  Our cRIO connects to our fine PC when it is initialized at first - and you can view it fine in MAX, Manager of distributed system and its web interface. But after all 3-5 minutes it always loses connection. It remains disconnected, and only restart the cRIO restores the connection but only for another 3-5 minutes. Only MAX restart does not help. We can ping the cRIO ok when 'disconnected' - which, to me, implies that it is a problem of higher level software.

  We had this particular cRIO work fine before.

  Thanks for your suggestions... While not in a rush to do this, I really want to understand why the connection is intermittent

  Here are some details:

  • MAX version 5.0.0f1
  • LV2011 DS2
  • cRIO is a 9022 (no screws running on it to the commissioning, CPU minimum load - idle = 97%)
  • computer development is a Vista Home Premium 32 bit
  • connected together using the brand-new Cat5E cable
  • TCP/IP settings on the laptop - Static IP, IP 192.168.2.4 address, mask 255.255.255.0
  • TCP/IP settings on cRIO - Static IP, the IP 192.168.2.1, mask 255.255.255.0 (gateway and DNS are blank or 0.0.0.0)
  • cRIO set to use for the link speed autonegotiation (no option to change this) and detection of packets = "interrupt".
  • PC value link autonegotiation speed, but has no effect on the problem, if it is set on a fixed, low speed for example. Half-Duplex 10 Mbps
  • PC Firewall is configured to allow the port 3580, and actually disable the firewall altogether change the problem

  Had the chance to try again with my intermittent connection to cRIO, and here's what I found:

  • Connection through a switch, rather than directly with crossover cable - made no difference, still kept disconnecting after 3-4 minutes
  • With no other network on my laptop other than the LAN - no difference development
  • cRIO with APP No. dip switch select IT - no difference
  • cRIO with game of dip-switch SAFE MODE - this time it is remained connected, but this mode is not very useful as a solution

  Then I was reinstalling the software cRIO as suggested - it did not complete the first time, but second attempt was beautiful and connection is now very stable (and has not abandoned in the last 30 minutes).

  Here are the instructions to reinstall (just in case useful for others):

  1. In the measurement and Automation Explorer (MAX), access remote systems | cRIO | Software
  2. Click on the "Add/Remove software", and an installation wizard will appear
  3. With currently installed version of the selected software - "then click to reinstall the software currently installed.
  4. Follow the rest of the instructions, and it should take about 4-5 minutes

  Thanks for your help

  Andy

• cRIO-9073 OR DAQmx compatibility

  It seems that the cRIO-9073 is not compatible with NOR-DAQmx.  That is a true statement or get something broken in the installation?  The I intend to use the modules are compatible with NOR-DAQmx, but I can't communicate with them using NOR-DAQmx.  I use LV 2009, MAX 4.6.2 OR-DAQ 9.0 and 3.3 OR RIO.  Suggestions appreciated.

  Thanks in advance.

  RunningDog

  Hello

  The cRIO-9073 isn't a DAQ card, it is a real time based with a reconfigurable FPGA system. In summary: you may not use NOR-DAQmx to program your cRIO system. Please read another post I wrote about how to get started with a cRIO system.

• Why do I get the compile time extremely long with FIFO on the cRIO-9073?

  I use a cRIO-9073 to develop a data acquisition system.

  When I try to use a FIFO to pass data to the host the FPGA, I get extremely long to compile (hours!).

  Currently, I use that a single analog input of a module 9205 in my loop FPGA.

  Y at - it an explanation for that?

  Thanks for any help you can provide.

  Michel

  Paul,

  Thanks for your reply.

  I finally found the problem: the size of FIFO, I requested in the properties of the FIFO was too large to 32K items (for the type of data the FIFO U32) 4 times. He was filling the FPGA, 128 KB of RAM completely, leaving no room for manoeuvre for the compiler for the remaining logic. So bad, there was no warning for that!

  By reducing the size of my FIFO at 4K, the compile time came in 5-10 minutes instead of hours!

  Michel Lanthier

• cRIO-9073 not appearing is not in devices and Labview 2009 targets

  In MAX, I show the following: a cRIO-9073 with NOR-RIO 3.0.0 installed. My system software has NEITHER-RIO 3.0. In LabView 2009, when I try and add the cRIO to my project in LabView 2009 in New-> targets and devices, I don't have a list in time real CompactRIO and my cRIO does not appear. I tried to add manually with its IP address, but it does not work either. I've updated the cRIO to LabView real-time 9.0 software.

  Is there other software that I need to update on the cRIO so that it is visible in LabView 2009? Do I need a new version of NOR-RIO?

  Thanks for any help.

  Todd

  I upgraded from NEITHER RIO NOR-RIO 3.2.1 3.0 and LabView 2009 seems happy.

  See you soon,.

  Todd