Connection printer square with Hotspot and Airport Extreme

Similar Questions

• What should I wear to the front with ATT and Airport Extreme?

  I have AT & T Uverse with an Airport Extreme.

  EI is implemented as a bridge, because it wouldn't work otherwise.

  I went into the game/NAT on the router/modem ATT layout and tried to activate some ports to forward.  Then I check the port and find that it is always closed.

  Someone here would be able to offer assistance with problems?

  I do this to try to send large files to a friend VIA files torrent based, although it does not seem to allow me to seed.

  Before ATT I got time warner and my own modem and router combo, and it works wonderfully in this configuration, so I can only the assertion that the issue is somewhere in the new place from the material.

  Now, if I try to download a standard torrent, I have no problem, but try to make my own with the trackers who have worked before, there is no dice.

  Thanks in advance for any help.

  ATT system is the NVG599 of ARRIS

• Connection printer 3050 has to new airport extreme router

  I just upgraded my router to the extreme of Apple Air Port and cannot figure out how to connect the printer to the router.  I do not have the CD that came with the printer and can't find where to download the HP software.  The printer is recognized on computers (Mac OS 10.9.2) goal will not display because it is "not connected" to the network.   Before, I just used the WPS option on the printer and pushed the button on the router.  Since this is not an option more, I keep looking, but does not know where to put the PIN either.  Help, please!

  Thank you!!

  Thanks for the reply.  I called Apple support and they walked me through the steps of adding a printer WPS to extreme Air Port (Airport basestations Menu utility (top), then select Add a WPS printer and then have it search for printer or enter the PIN).  He missed by looking at the menu at the top of the AirPort Utility where the Menu Option of base station is... But I can't believe how it was difficult to try to find a solution to the HP Web site for that!  Looks like it would be a simple soultion to the list.

• Cat left on Xbox 1 with Cox and Airport Extreme

  Hi all

  I can't use the group chat.  He said "the only way to get my router to work with Cox had to define the link local IPv6 and to have a self assigned IP."  My NAN is set to OPEN, so it's not the problem.  I get this error code:

  0 x 89231806

  Configuration of the network block you chat away

  I opened the recommended ports and still does not work.  My router is set to DHCP and NAT. Can someone please?  Beyond frustrated!  Does anyone else have this problem?

  Thank you

  Heather

  Hello

  Your Question is beyond the scope of this community...

  I suggest that repost you in the Xbox Forums.

  "Xbox a Preview program FAQ.

  http://support.Xbox.com/en-us/Xbox-one/system/Xbox-update-preview-FAQ

  'Home'

  http://forums.Xbox.com/

  "Xbox forums.

  http://forums.Xbox.com/xbox_forums/general_discussion/f/3817.aspx

  _________________________________________________

  "Xbox Forums directory.

  http://www.Xbox.com/en-us/forums

  General

  • Home/FAQ/Forum policy

  • Community general discussion

  Material & Discussion Services

  • Equipment & Services

  Xbox support
  Agent hours: M - F 09:00-17:00 PT

  • Xbox 360 support

  • Xbox 1 support

  • Xbox on supported mobile devices

  • Xbox on Windows support

  • Networking of hardware information

  • Material information TV

  Law enforcement forums

  • Xbox 360 account Suspensions & Console bans

  • Account Xbox one & measures Console application

  • Announcement
    PLEASE READ. Introducing changes of case review & forum

  Technical support of Xbox Live rewards
  Xbox Live rewards Squad hours: M - F 09:00-17: 00 PST

  • Xbox Live rewards program announcements

  • Xbox Live rewards Questions

  See you soon.

• Can I use old time capsule for storage only with a new airport extreme (standard want latest HQ)?

  I have a time Capsule elders (802.11n). I would like to know if I can still use this time Capsule only as a network storage device, if I decide to build my network with a new Airport Extreme (802.11ac). If I can do that, how would I set up the network to continue automatic backups with a router to update?

  To do what you want, the new AirPort Extreme 802.11ac would be installed as the "main" network router The time Capsule would be connected to the AirPort Extreme, using a wired Ethernet cable connection, and the time Capsule should be configured to run in bridge with the service Mode Wireless off.

  Any Mac you want to save in the time Capsule would need to have Time Machine preferences on each Mac adjusted to ensure that the time Capsule has been set as the target for backup.

  If you decide to add the AirPort Extreme, post back for more information at this time, if you need installation instructions step by step.

• connect the hard disk drive to airport extreme

  I have Airport Extreme running.

  I have connected a HARD drive to the Airport Extreme, but do not see the device of the HARD drive in the Finder

  How to map iTunes to play music files devices HARD drive to play music?

  The drive must be formatted in FAT16, FAT32 or Mac OS extended (journaled) and may need its own supply. If these criteria are met, use the connection to the server command in the Finder Go menu to access.

  (141910)

• Printing problems with XP and Lexmark-documents are just stuck in the print queue

  Original title: printing problems with XP and Lexmark

  Until yesterday, I was able to print OK using Windows XP and a Lexmark Printer series 3500-4500 with wireless capabilities.  Reported network test wireless (on printer) and report indicates that there are no reported problem, also did the diagnostic test and which shows no problem either.  I can't print and documents are just stuck in the print queue - please can someone help, it drives me crazy because it's probably a very simple solution.

  I guess you do not have all of the error messages.

  It is possible that comes to mind that your printer has received a new IP address of your router (this could easily happen if you have several computers and other devices that connect to your wireless network).

  Find the IP address of the printer of his network diagnostic page.
  Click Start > printers and faxes, right-click the printer and select Properties
  Select the Ports tab, then click on the button "Configure Port" (be careful NOT to click anywhere in the list of ports)
  Make sure that the IP address in 'Port settings' is identical to that shown on the diagnosis of your network printer page.

  To avoid this problem in the future, you must configure the printer to have a static IP address.  See your printer User Guide for instructions.

  Choose an appropriate subnet address (i.e., has the first 3 groups of numbers the same as the other addresses in your network) but who is not in the range of addresses assigned by the DHCP server on your router.  See the User Guide of your router for more details.

• Asslam o aliakum. I have a problem with itunes 12.3.2 it is not downloaded the 10 windows and when I connect m iphone with itunes and want to update to 9.2 says please download itunes new version for ios 9.2... help me with this... How to solve this probl

  Asslam o aliakum. I have a problem with itunes 12.3.2 it is not downloaded the 10 windows and when I connect m iphone with itunes and want to update to 9.2 says please download itunes new version for ios 9.2... help me with this... How to solve this problem.

  Greetings Dani56777,

  Thank you for using communities Support from Apple!

  I understand that you run Windows 10 and you must update iTunes to the latest version so that your iPhone will be recognized when connected. I do not know if you receive an error when you try to update iTunes or not.

  If you need information on how to update iTunes, please follow the instructions in the following link.

  Download the latest version of iTunes for Windows - Apple Support

  If you receive an error or alert, you can consider removing iTunes and all of its associated components and then reinstalling fresh iTunes on your computer. That would give you the latest version of iTunes. If you need execute this process, please follow the steps described in the following article.

  Remove iTunes Control Panel and its associated components

  Use the control panel to uninstall iTunes and software components in the following order:

  1. iTunes
  2. Apple Software Update
  3. Apple Mobile Device Support
  4. Hello
  5. Apple Application Support 32-bit
  6. Apple Application Support 64-bit

  On some systems, iTunes can install two versions of the Apple Application Support. What is expected. If both are present, do not forget to uninstall both versions.

  Do these elements in a different order, uninstall or uninstall only some of them. This could have unintended effects. After you uninstall a component, you may be asked to restart your computer. Wait to restart your computer until you finish remove all components.

  Remove and reinstall iTunes and software for Windows 7 and later versions - Apple Support components

  Have a great day!

• Connectivity with AT & T-Motorola 3360 and Airport Extreme problems

  Bought a new extreme-Airport (7.7.3) to replace my old AE after 9 years of service.  The installation procedure, but could not get the airport to connect with my modem (Motorola 3360).  Called at & T and they crossed put me the modem in Bridge mode and which seemed to work.  But only temporarily (about 5 hours).  Restart the modem and the airport was not working.  Troubleshooting I tried to plug my MacBook directly into the modem, but even the computer couldn't get an internet connection.  Another call to AT & T and they reconfigure the modem to their end.  After 90 minutes and try everything they could, they have finally admitted defeat and told me that they could not solve the problem.

  However, after a fairly exhaustive search of this forum, seems to be two issues that many people is with Airport extreme.  One is that the modem (in this case a Motorola 3360) is perhaps not fully compatible with the airport.  The AT & T support person was not aware of this until I asked about it, so she did a quick search and was rather surprised to see that there is a lot of people having problems with the Motorola Modem.  She told me that they use no more Motorola modems but ship the 6200 of Netgear.  "All know issues?", I asked.  She sought and, to his surprise, even once, there was.

  So, first question.  Does anyone know a modem that is compatible with the airport or use one that they had to limit problems with?

  The second question prevailing seems to be with the IPv6 protocol.  Anyone know if there are problems with the AT & T IPv6 protocol and the most extreme airport?  I did not disable IPv6 yet to see if that helps.  I thought I'd ask here first.  Couldn't find anything on the AT & T site.

  When I return from the road (great place to go to get away from technology) I will make a new round of full power of all the components and try Setup again from scratch.

  Any ideas or suggestions would be greatly appreciated.  Miss all know profanity.

  Thank you.

  Any other relevant information: 6.3.1 the utility Airport, Airport Extreme 7.7.3, MacBook Pro running 10.8.4, modem Motorola 3360, AT & T high speed DSL, shoe size 11-1/2 wide.

  When you have configured the 3360 as a 'bridge', this would mean that the AirPort Extreme should then be put in place to provide the PPPoE connection service. The airports are not known for their reliability in this type of installation... no matter the type of modem that you can select, so I drop this method as a connection option.

  If you want to keep the 3360... and you have time to experiment... then you can set the 3360 to its original default settings and configure the router from the airport most convenient to connect using DHCP in router Mode of DHCP and NAT.  That will produce what is called a message Double NAT, but maybe it's not of concern on a simple home network, and Apple provides you with the option 'Ignore' the Double NAT, so the airport will display a green light instead a light orange blinking slow.

  You need to try this configuration for a few days to see if the Double NAT will be a problem or not, because it is not possible to predict the effect of a Double NAT on a network... you have to test a few days see how things behave.  If this configuration works well, for you, then you can leave it as what.

  Please note that I do not recommend this type of installation, just suggesting it as an option this work could , if you want to keep the 3360.

  How Double NAT affect IPv6, I can't tell, since I did not use att for several years, and I'm not familiar with their implementation. On wired, IPv6 works fine on the airport with Comcast and Time Warner.  We can provide these parameters for you if want, but have no idea how well... (or if)... they will work with ATT.

  If the installation of Double NAT does not work, your best option would be to go there and get a modem/router or gateway to ATT device and then set up the most convenient airport in Bridge Mode works correctly with the modem/router ATT.  You will turn on the routing of ATT function in this type of installation, but the airport can also produce a signal from the wireless network that you can use.  The modem/router ATT will also provide a wireless signal that you could use for guests, or disable the feature, if you do not need two wireless networks.

  This may also be the best option if you want to configure IPv6 as IPv6 of ATT service must be compatible with the modems/routers and gateways.

• Internet connection with XP Pro SP3 and Airport Extreme - possible only Internet with no secruity, WEP - "status is always acquiring network address.

  IMac seen the router and connected flawlessly, Sony Vaio however under secruity always gives me "absorbing the network address", I was looking around and heard xp pro sp3 has problems with wpa2 so I changed the settings for wep on apple Airport extreme and it STILL does not work. If I have no secruity that it picks up the signal from the internet and everything is fine. I tried to update the drivers for the wireless LAN card already, any input would be great

  SOLVED... apparently xp pro sp3 has problems with wpa2, it refuses to connect. I went to settings on extreme airport secruity but wep was not an option, I had to click on OPTION on my MAC keyboard, then click the settings secruity and wep is there, so I removed all the "preferred networks" and restarted the process 'learning' on the vaio and everything's fine. Thanks for all the help, I can get some rest tonight

• Internet connection with Windows XP, SP3 and Airport Extreme - the status is always "absorbing network address.

  My Airport Extreme connected my IMac immediately, but I am not able to connect on the side PC. Airport utility does not 'no matter what Airport wireless devices". When you check the status of the internet connection with PC tools, the correct network is indicated and shows an excellent signal strength. The status is: "absorbing the network address. However, nothing happens.

  Under 'Repair the wireless network connection', it shows, "Windows is taking the following steps: your IP address renewal" even once, nothing happens.

  Under hardware I show Atheros Wireless Network Adapter and the mention: "this device works correctly.

  Yet, no network connection. Any help will be greatly appreciated.

  Hello

  Keep the changes and open the wireless. For example, to disable security in the router (turn on when to managed to connect).

  You can also try the wireless in a friends house, or an Internet café to get a frame of reference for this behavior elsewhere.

  -------------------

  Wi - Fi in general.

  These steps and tell us where is the breaking point.

  Check the Device Manager for the wireless card valid entry.

  http://www.ezlan.NET/Win7/net_dm.jpg

  If there is no valid entry, remove any entry from fake and re - install the drivers for the wireless card.

  Check network connections to make sure that you have a network icon/entry wireless connection, and that the properties of the icon (right-click on the icon) are correctly configured with the TCP/IPv4 protocol in the properties of network connections.

  http://www.ezlan.NET/Win7/net_connection_tcp.jpg

  ------------------

  The wireless card drivers much also install utility wireless of the seller.

  Make sure that if there are teas from Wireless Utility of seller does not work with the native Windows wireless utility (Service WLAN).

  ----------------

  Make sure you firewall No. preventing / blocks wireless components to join the network.

  Some 3rd party software firewall continue to block the same aspects it traffic Local, they are turned Off (disabled).

  If possible set up the firewall correctly, otherwise totally uninstall and get rid of its remaining processes that permit the own local network traffic flow.

  If the 3rd party software is uninstalled, or disables, make sure Windows native firewall is active .

  party like Hello and NetMagic 3rd network managers can block local traffic too.

  ---------------------------

  Stack TCP/IP work should look like.

  Right-click on the wireless network connection card, select status, details and see if she got an IP address and the rest of the settings.

  http://www.ezlan.NET/Win7/status-NIC.jpg

  Description is the data of the card making.

  The physical address is MAC of the card number.

  The xx must be a number between 0 and 255 (all xx even number).

  YY should be between 0 and 255

  ZZ should be between 0 and 255 (zz all the same number.)

  The date of the lease must be valid at the present time.

  * Note 1. IP that starts with 169.xxx.xxx.xxx isn't valid functional IP.

  * Note 2. There could be an IPv6 entries too. However, they are not functional for Internet or LAN traffic. They are necessary for Win 7 homegroup special configuration.

  ---------------------------------------------------

  A message in the small window that says connected wireless doesn't means that you are really a valid functional connection.

  Above everything is OK, you must be able to connect to the router.

  Connection to the router means that you can enter the IP of the router base in an address bar in one go, being able to connect and configure the router menus see.

  If it doesn't connect to the router, journal newspaper from any computer that can connect to the router wirelessly with a wire, disable wireless security, make sure that the wireless SSID broadcast is enabled and try to connect with no. wireless security.

  Enable security wireless after you eat to make a functional connection.

  Jack - Microsoft MVP, Windows networking. WWW.EZLAN.NET

• HP C4780 and Airport Extreme: says "device not connected" when installing wireless

  Hello.  I appreciate any help with this problem.  I searched but I've not found anything exactly similar.  I have a MacBook Pro under OSX 10.5.8 and an Airport Extreme.  I am trying to set up a HP C4780 printer using the HP installation software.  The printer is connected to the Mac via a USB cable for Setup, and all the steps of the Setup routine recognized the printer.  Until... when I get to the part "network wireless configuration" of the process, Setup HP sees my network (802.11n, the type of encryption WPA_PSK) and asks for my password.  After I entered the pw, it runs for about 20 seconds and gives me the following message: "device not connected.  To configure the network settings for the device selected, please temporarily connect via USB. The device can be disconnected from the USB once the network settings are transferred. »

  My printer is well connected by USB, however.  By reading some similar positions, I tried the following: limit the wireless to channell 11, by clicking on the button "allow this network be extended" and disconnect the printer before the launch of wireless setup.  I also tried several bottles of beer, but which only degrades the connection between the keyboard and the seat.  No luck so far.  Any help would be appreciated.  Thank you.

  C4700 series has a bug in the firmware where it crashes when meeting a SSID of 6 characters.

  Change your SSID to 10 or 12 characters until a firmware fix is published.

  If this does not work, drink more beer.

• IPv6 and AirPort Extreme Gen 5 connection drops

  My ISP is over native IPv6 but the AirPort Extreme (AE) abandons the connection every 30 minutes or more.

  I've tried different settings IPv6 and the only one that gave stable results is to:

  -Block all the incoming IPv6

  -Allow teredo and IPSec tunnels

  -IPv6 tunnel fashion game

  If IPv6 is set to native, airport utility shows the Internet connection disabled. So far with the tunnel mode, it seems to work. IPv6 - test.com results show 6to4 good feature as well.

  Someone else had problems with the products of the AE and IPv6 settings?

  He would have nothing to do with IPv6, but the problem was triggered by the latter.

  This modem do you have? Brand and model please.

  And who is your Internet provider because your Setup sounds weird... it should not be necessary to the IPv6 block.

• Can I connect a wireless modem to my Airport Extreme base station via ethernet and then connect this Ethernet modem to my TV to pinterest?

  Hello

  I want to connect my TV to my Airport Extreme via ethernet, so I can run Netflix. Can I just the branch? Can or, if it does not reach, I use an old router as a bridge linking to the Airport via an ethernet cable and connect the router to the TV?

  Thank you

  Lisa

  I want to connect my TV to my Airport Extreme via ethernet, so I can run Netflix. Can I just the branch?

  Yes.

  Can or, if it does not reach, I use an old router as a bridge linking to the Airport via an ethernet cable and connect the router to the TV?

  Yes. It is also possible, but only by using an Ethernet switch instead of a router would be a better solution. The important thing is the total distance of Ethernet between the extreme and the TV. Ethernet is limited to 100 m (328 ft)

• Problem with SlingTV through Airport Extreme?

  I have a Motorola SB6141 cable modem, internet of Time Warner and an Apple Airport Extreme Base Station (later) for my setup. While SlingTV is not a great service, it was $ 20 a month and gave me what I need and has been much better than that Time Warner was in charge me for the same channels.

  Despite the problems of freezing SlingTVs or what not, for a while it worked. But one day a few months back it just stopped working. When you open the app, it either does not open or just turns and turns to be forgotten and never access the content. But if I try on my phone (Verizon LTE), or another network outside my apartment with the iPad or computer laptop, it works. So at home, I tried to go directly from the cable modem and right in the Apple TV (previously an Xbox) and when I do that it works. So really what it boils down to, is my Apple Airport Extreme Base Station router. If I'm either directly connected to the Airport Extreme Base Station (Apple TV ethernet to the router), it will not work, or if I use WiFi via the Apple Airport Extreme Base Station it will not work. But directly to the modem cable or on any network outside of my home, the service works.

  So in short, something about setting up Apple isn't allowing the Sling TV app to open or work on any device. I even did a rest of the plant and installing my Apple router once again, and the same problem persists.

  FYI - I use Netflix, Amazon Prime, Hulu and all the Apple TV, TV shows, rental movies and content without ever having a problem with opening or streaming. This only happens with SlingTV when you try to access content on any device (iPad, Apple TV, Xbox One, iPhone, Macbook Air) via WiFi or Ethernet via Apple Airport Extreme.

  I tried to provide all the little details that I could. If someone could please provide a solution I would really really appreciate it! Thank you.

  Well first of all try to port forwarding. Slingbox I guess would use a similar to SlingTV montage... Unfortunately when I google for it I see just people having so many questions like you... no rigging, no answer they give up.

  http://PortForward.com/English/routers/port_forwarding/Apple/AirPortExtreme/Slin gBox.htm

  It is the old airport of model, but the idea is correct.

  If you still have questions... There is a major problem... port 5001 is used by the airport for its installation...

  If I run a scan of port of network utility, that you will find that it is already used.

  Port scan started...

  Host port scan: 192.168.2.201

  Open TCP Port: 5001 commplex-link

  Open TCP Port: 5009 winfs

  Port scan has completed...

  My recommendation is to replace the airport as your main router... Something good market like the C5 TP-Link or the WR1043ND which is less than $50US. These routers use UPNP is missing on the airport. Continue to use the airport for your customers to apple as WAP and switch.

  BTW: this is no bad thing because you also have a known problematic modem... SB6121 and SB6141 have major problems... do a quick search and you can find a lot of posts about this.

  TWC has also now use IPv6... that can ruin.

  See the instructions for installation (same as comcast for TWC).

  http://mydeviceinfo.Xfinity.com/download.php?file_id=35