convert a light 1602i to stand alone?

Similar Questions

• A stand-alone 1252 can be converted to AP light?

  I received incorrectly an AP 1252 (AIR-AP1252AS-E-K9 model number) and hope to convert to a light AP. But in the documentation for this device is missing in the list of devices that can be converted.

  I am also unable to find a tool to upgrade for this model.

  Is it possible to convert this device?

  Someone on the forum used the last upgrade tool and siad, he was able to convert the LWAPP 1252. You can try it, otherwise here are the steps of another Member on the conversion of these ap:

  Here is a method to perform the conversion.

  * Method 1: (Mode key) *.

  1. install an external tool of TFTP for example tftpd32 from http://tftpd32.jounin.net/ tool

  2. assignment of IP address in the range of 10.0.0.2 -.254 (Ex: 10.0.0.3) to the TFTP (your laptop or pc).

  3. download the IOS lwapp image on the tftp root directory. Use http://www.cisco.com or

  http://tools.cisco.com/support/downloads/go/IPCheck.x?defAdv=N&sftAdv=N&image=c1250-rcvk9w8-tar.124-10b.JA3&filepath=/swc/esd/02/crypto/3DES/281235915/guest&filename=c1250-rcvk9w8-tar.124-10b.JA3&advUrl=null&isk=Y&defInd=N&mdfid=281235915&sftType=Autonomous%20To%20Lightweight%20Mode%20Upgrade%20Image&optPlat=&relVer=12.4 (10B) JA3 & starts = 271159 & treeMdfId = 278875243 & tree_name = wireless

  4 rename c1250-rcvk9w8 - tar.124 - 10B .JA3 c1250-rcvk9w8 - tar.default

  5. make sure that you set the IP address on the IVB of the AP interface if it is not set. Set it in the 10.0.0.x range default is 10.0.0.1.

  6. connect the Ethernet port on the AP to your server TFTP (laptop)

  7 press and hold the mode button and power off of the AP.

  8 power back the AP while constantly maintaining the button mode for 20-30

  seconds.

  * Method 2: (Archive command) *.

  1. install an external tool of TFTP for example tftpd32 from http://tftpd32.jounin.net/ tool

  2. assignment of IP address in the range of 10.0.0.2 -.254 (Ex: 10.0.0.3) to the TFTP (your laptop or pc).

  3. download the IOS lwapp image on the tftp root directory. Use http://www.cisco.com or

  http://tools.cisco.com/support/downloads/go/IPCheck.x?defAdv=N&sftAdv=N&image=c1250-rcvk9w8-tar.124-10b.JA3&filepath=/swc/esd/02/crypto/3DES/281235915/guest&filename=c1250-rcvk9w8-tar.124-10b.JA3&advUrl=null&isk=Y&defInd=N&mdfid=281235915&sftType=Autonomous%20To%20Lightweight%20Mode%20Upgrade%20Image&optPlat=&relVer=12.4 (10B) JA3 & starts = 271159 & treeMdfId = 278875243 & tree_name = wireless

  4. make sure that you set the IP address on the IVB of the AP interface if it is not set. Set it in the 10.0.0.x range default is 10.0.0.1.

  5. connect the Ethernet port on the AP to your server TFTP (laptop)

  6. at the point of access, type archive download-sw / overwrite/force-reload tftp: / //c1250-rcvk9w8-tar.124-10b.JA3

  ****************************************************************************************************************************************

  The other direction (lwapp to stand alone)

  http://www.Cisco.com/en/us/docs/wireless/access_point/conversion/LWAPP/upgrade/guide/lwapnote.html#wp161272

  ****************************************************************************************************************************************

  If you must manually 'Prime' the LWAPP:

  Ap #lwapp AP ip address

  AP #lwapp ap ip default-gateway

  Ap #lwapp AP controller ip address

  Hostname ap AP #lwapp

  (optional)

• Conversion of Cisco Aironet 1130AG light in stand-alone mode

  Hello

  I just bought AIR-LAP1131AG. Unfortunately, I want stand-alone and not lightweight fashion.

  Yes, is there a procedure to convert to "AIR-AP1131AG?

  Thank you.

  Hello Michael,

  Yes, please follow this procedure for TFTP Re-imaging

  / * Style definitions * / table. MsoNormalTable {mso-style-name: "Table Normal" "; mso-knew-rowband-size: 0; mso-knew-colband-size: 0; mso-style - noshow:yes; mso-style-priority: 99; mso-style-parent:" ";" mso-padding-alt: 0 to 5.4pt 0 to 5.4pt; mso-para-margin: 0; mso-para-margin-bottom: .0001pt; mso-pagination: widow-orphan; do-size: 10.0pt; do-family: "Times New Roman", "serif" ;} "}

  1) Go to your Computer and from the tool menu -> folder options ->uncheck the hide extensions for known file types option. 

  2) Download the IOS image ( you can get this ios image from cisco.com) on your desktop.

  3) Rename the image into c1130-k9w7-tar.default

  4) Give your computer Ethernet an address in the range 10.0.0.2 till

  10.0.0.30

  5) Run the tftp server on your computer.

      - Make sure that the directory of your tftp server is the desktop.

      - Specify the AP address on the tftp server if needed.

  6) Connect the AP to the computer with Ethernet cable.

  7) Remove the power from the AP.

  8) Press and hold Mode button on the AP, and insert the power jacket in the AP.

  9) Keep pressing on the Mode button for (20-30 seconds) until you see RED Led.

  10) Wait until the image installed and all led lights return to green 

  doesn't make sure that no firewall or antivrus is running on your computer.

  I hope this helps.

  Kind regards

  Talal

  =============

  Please note the answers that will help you

• Coverting 2602 light to stand alone (for the site survey)

  Hello

  I have a conversion problem 2602 light on its own.  It will not start to standalone IOS.  The following is what I did.

  AP: value 10.0.0.1 IP_ADDR

  AP: the value of 255.255.255.0 subnet mask

  AP: tftp_init

  AP: ether_init

  AP: flash_init

  AP: tar - suchftp://10.0.0.5/ap3g2-k9w7-tar.152-2.JA.tar flash t:

  extraction begins

  After the extraction process.

  AP: set BOOT flash;/ap3g2-k9w7-tar.152-2.JA

  AP: start

  Please see attached figure of the AP.

  Thnaks

  If you have another image in flash you must remove it and try again to load the stand-alone image

  When you remove the capwap image file, you must delete each file inside this folder, and then delete

  empty the folder as a result using the rmdir command.

  -----------------------------------------------------------------------------------------------------

  Please don't forget to rate correct answers

• Question: With the new stand-alone converter how do you do a cold P2V? (booting from CD)

  With the new stand-alone converter how do you do a cold P2V? (booting from CD)

  Well, I see that cold Conversions are more supported.

• RedHat 5 video failure using stand-alone converter

  I'm running a 64-bit Redhat Enterprise Server and P2V trying it.

  Converter using Stand Alone Client 4.01. Build 161434

  Server ESXi Version 4.1.0

  She will run and do not reach 1% with the "FAILED: methodfault.summary" error.

  On the server, it registered the fault as:

  Warning message on RedHat: insufficient video RAM. The maximum resolution of the virtual

  machine will be limited to 1176 x 885. To use the configured maximum resolution of 2560 x 1600,

  increase the amount of video memory allocated to this virtual machine by setting svga.vramSize = "16384000"

  in the virtual machine configuration file. WARNING 11/29/2012 14:30:08 RedHat root

  When this does not work it will remove the virutal machine and there is no file settings to update.

  Any ideas how to make this work?

  Thank you!

  If you have a Windows machine, you can try to use the converter 5.0.1.

• TMac new user: I installed lighthouse to my Admin profile and see no light in my user profile.  It's a new stand-alone Mac computer.  How do I enter other profiles on this PC (Mac) Headlight?

  TMac new user: I installed lighthouse to my Admin profile and see no light in my user profile.  It's a new stand-alone Mac computer.  How do I enter other profiles on this PC (Mac) Headlight?

  Thanks Ned,.

  This is new for me. The name is LightRoom.

  I found the solution: install in each profile using the same numbers of activation.  Seems OK now.  Thanks again.

• Blue screen after with VM stand-alone converter P2V conversion

  Hello

  I started to implement VMware in my company.

  I installed standard Vspahere 5 withouth any problem and made all configurations.

  For the moment I want to convert the physical server, the virtual machine and for this I have download VMware-converter stand alone.

  I fist he installed on a Windows 2008 server that I want to convert.

  The conversion was adopted without any error message but in the end the virtual machine cannot start normally.

  I have a blue screen with thos messages:

  "Launch Startup Repair tool" or "start windows normally".

  I converted to the other servers, but I don't know how to proceed with this error message.

  Please could someone help?

  Thank you

  Above all this happen, after the virtual machine is converted the selected SCSI adapter would be logical bus, because of which the VM throw a blue error screen.

  change the logic of the bus at LSI logic (windows 2 k 3, 2 k 8, vista)

  How to change see below KB:

  http://KB.VMware.com/kb/1002149

  Please allow points for correct/good answers by clicking on the tabs

• VM Converter Standalone can convert a vm running on a standalone ESX 2.5.5 server directly to a stand-alone server ESX 4.1?

  Based on documents - VMConverter http://www.VMware.com/PDF/convsa_43_guide.PDF

  Destinations and source pages 22-26 - supported

  VM Converter Standalone 4.3 v can convert a vm running on a standalone ESX 2.5.5 server directly to a stand-alone server ESX 4.1? It appears that it can in the guide. Is this correct?

  VM Converter Standalone cannot convert a power off vm on an ESX 2.5.5 standalone server directly to the ESX Server 4.1 by guide unless the 2.5.5 ESX Server is managed by vCenter 2.5. Is this correct?

  Please confirm. There is some contention about this topic with their peers.

  All points will be awarded.

  Thank you.

  According to the documentation you can hot covert one ESX 2.5.X, if you manage the ESX with Virtual Center 2.5 or higher server.

• Change IOS on AP 1131AG light to stand alone

  Hi experts,

  can anyone advice if the ap 1131ag IOS can be changed to stand alone? can you give me a link where I could get a standalone IOS and how? Thank you!

  Follow these steps to return mode LWAPP stand-alone mode by loading a version of Cisco IOS using a TFTP server:

  Step 1 the IP address of the computer on which the server software runs TFTP should range from 10.0.0.2 to 10.0.0.30.

  Step 2 make sure the PC contains the file access point (for example, c1200-k9w7 - tar.122 - 15.JA.tar for a 1200 Series access point) in the TFTP server folder and the TFTP server is activated.

  Step 3 set the timeout on the TFTP server in 30 seconds.

  Step 4 on the PC where, the TFTP server perform the following steps:

  a. disable the firewall, such as Windows, ZoneAlarm firewall firewall software, McAffee firewall or other.

  b. ensure that all Windows are visible. In Windows Explorer, click Tools > Folder Options > view. Deselect hide them extensions of known file types check box.

  Step 5, rename the access point image file in the folder of the server TFTP c1200-k9w7 - tar.default for a series of 1200 access point, c1130-k9w7 - tar.default for a series of 1130 access point, c1240-k9w7 - tar.default for a 1240 series access point and c1250-k9w7 - tar.default for a 1250 series access point.

  Step 6 connect the PC to the access point using an Ethernet category 5 cable (CAT5).

  Step 7 disconnect the power to the access point.

  Step 8 push the MODE button and hold the button while you reconnect power to the access point.

  Step 9 hold the MODE button until the status LED turns red (approximately 20 to 30 seconds), then release.

  Step 10 wait until restarting access point, as indicated by the LEDs become green followed the status LED flashes green.

  Step 11 after the access point reboots, reconfigure using the GUI or the CLI.

• Can I convert my license creative cloud in a stand-alone license for Lightroom?

  Hello

  After a few months, I realized that I have one license per month. I really want to buy a stand-alone license and have my own software. What can I do? Thank you

  Hi clap

  CC of Lightroom is based subscription product that comes with Photoshop in photography Package(or any other plan)

  It can not be changed for a stand-alone product

  A product independent 6 Lightroom is available Separately.See products

  Let us know if this helps

  Concerning

  ~ Assani

• Mode conversion controller in stand-alone mode in cisco 1702

  I have cisco AP 1702 and in controller mode. I don't have the controller so want to convert in stand-alone mode. I went through various items for this and found this interesting way to do.

  Run this command to convert:

  # swarm - Standalone mode
  # reload

  I found this on this link: http://community.arubanetworks.com/t5/Controller-less-WLANs/How-to-conve...

  Similarly, going through the longer process, I downloaded this for the standalone mode: https://software.cisco.com/download/release.html?mdfid=286281141&flowid=...

  and for stand-alone mode, I have this one: https://software.cisco.com/download/release.html?mdfid=286281141&flowid=...

  Here are the files I'm looking for?

  Help, please.

  This original link can cause a headache for an Aruba AP which is different.

  Try this method:

  https://ripplesinharmony.WordPress.com/2013/01/28/downgrading-a-Cisco-lightweight-AP-to-autonomous-mode/

  The software of the first link you posted (https://software.cisco.com/download/release.html?mdfid=286281141&flowid=71622&softwareid=284180979&release=15.3.3-JC1&relind=AVAILABLE&rellifecycle=ED&reltype=latest) will work for the standalone mode (stand-alone).

  This second link is light which means the controller-based and you don't want that for this scenario.

  See you soon,.

  Ric

• I have a (AIR-LAP1131AG-A-K9), I can set it up as a stand-alone?

  I have a lightweight access point (AIR-LAP1131AG-A-K9). I would like to use it as a stand-alone gateway (AIR-AP1131AG-A-K9). Is this possible? There are configuration changes that need to happen to make this happen? Do I need to use different operating system?

  Thank you

  Siva

  Plug the AP directly on your PC not the router.

  The best way to proceed is to comfort in the AP and make sure that the

  AP can reach the laptop via a switch or a crossover cable

  fixing directly from the laptop and the AP.

  With your cable from the console, you will be able to see if you pressed on the

  button for 20 seconds.

  By using a TFTP server to revert to a previous version

  Follow these steps to return standalone by LWAPP mode

  Download a version of Cisco IOS using a TFTP server:

  Step 1 in the IP address of the computer on which your TFTP server

  software should be from 10.0.0.2 to 10.0.0.30.

  Step 2 make sure that the PC contains the image point (for example file

  as c1200-k9w7 - tar.122 - 15.JA.tar for series 1200 point access) in the

  The TFTP server folder and the TFTP server is activated. Monitor of the

  TFTP program to see the code for transfer to the AP.

  Step 3 Rename the access point image file in the TFTP server folder

  C1200-k9w7 - tar.default for series 1200 point access,

  C1130-k9w7 - tar.default for a series of 1130 access point, and

  C1240-k9w7 - tar.default for 1240 series access point.

  Step 4 connect the PC AP with a category 5 (CAT5)

  Ethernet cable. This must be a crossover cable if connected

  to the AP. Or ethernet cable is normal if the AP and laptop are connected

  to a switch.

  Step 5 disconnect the power to the access point.

  Step 6 push the MODE button and hold the button while you reconnect power to the access

  point.

  Step 7 press and hold the MODE button until the status light turns red

  (about 20-30 seconds), then release.

  Step 8 wait that access point restarts, as attested by all lights

  Green followed the status light blinks green.

  Step 9 after the access point reboots, reconfigure using the graphical interface or

  the CLI.

  If the image is not download from Server/tftp on your computer, you may need to delete the previous image of tar on the access point of the console:

  Simply hold the mode button until the light is red.

  Then, by using the console port, make sure that the guest is AP: and do a show «»

  "Flash:" on the device and make sure that there is no image that begins

  "c1130-rcvk9w8-tar..." ». If there is an image that starts with who then

  Delete it with "delete flash:

• Connect a mounting rack system UCS stand-alone server

  Hello

  I read somewhere on the dcoumentation this server from Cisco to stand alone as c210, c250 can be attached to the UCS Interconnect fabric. Can some expert cisco shed some light in there?

  I think I know,

  I'll have to plug the UCS FI External rack mount FEX and Cisco servers connecting to the FEX. Can someone clarify?

  What are the system requirements for the configuration above to UCS?

  I configured ports UCS FI as server ports and connect them to an external FEX with Twinaxial cable. But the ports are the link down. Cable Twinaxial is supported? I have to do additional configuration that we do when you plug a Nexus 5000 on a FEX?

  Any help would be apprciated.

  Thank you.

  The connection to a server in a stand-alone rack details are covered in this doc

  https://supportforums.Cisco.com/docs/doc-15034

  Dave

• convert image light AP1131AG-A-K9

  Hello

  How to convert an AP1131AG-A-K9 AP image which is supported by a 5508 controller?

  Thank you.

  Download a recovery image (for example c1130-rcvk9w8 - tar.124 - 10B .JDA .tar) for this model of Cisco AP & then upload it to your stand-alone gateway by using a TFTP server with command below.

  AP5475.d0f5.2EE7 # Archives/force-reload download-sw / overwrite tftp://x.x.x.x/c1130-rcvk9w8 - tar.124 - 10B .JDA .tar
  

  Here is an example of post how to do this coversion

  Once that your AP is ready to sign up for a controller.

  HTH

  Rasika

  Pls note all useful responses *.