Creating team to implement the dual ethernet LAN port?

Similar Questions

• NX7K VDC: port of groups in the module Ethernet 48 ports 1 G / 10G F2?

  Have two or three questions about the allocation of ports on the Ethernet 1 module G / 10G F2 to VCC. Thanks for any help.

  (1) the most recent is F2 1 G / 10 G 48-port Ethernet module has groups of ports such as 10 G 32 ports older Ethernet module? If Yes, where can I get information on the mapping between the ports and port groups?

  (2) the module of 10 G of 32 has old ports of ports dedicated or shared because of its bandwidth of 80 G to the fabrid of switching mode. Is each port of the latest F2 10G module at the rate of 10G line or the same as the older 32 ports module? I want to make sure that the ports of 10G for link peer vPC are online.

  Thanks again

  Sent by Cisco Support technique iPad App

• Interface issues Netgear Smartswitch to the Cisco 881 LAN port

  Hi, we have 100 routers Cisco 881 in our network and they work all fine for the Linksys, 3Com, switches etc.  The problem we encountered is interfacing to switches from Netgear.  Netgear switches use automatic detection on their ports and it doesn't seem to be compatible with auto MDIX detection on the LAN Cisco 881 4 serial ports on the router 881 hub.  Someone has encountered this problem before?  A cross over cable solve the problem?  Since both executed MDIX autosensing they never synch - so probably a cross on would not make much.  I see this with all Netgear smartswitches.  If you put a small switch between the Netgear switch and router Cisco 881 everything works well except to pass traffic to port 9000.  Any ideas would be appreciated.

  See you soon,.

  Len

  Hello

  There should be no problem using crossover cable. You can try disabling autoMDI/MDIX (not auto mdix) on the cisco device and keep a straight cable but if it fails, use a crossover cable.

  Concerning

  Alain

  Remember messages useful rate.

• Computer laptop 15-ac132ds: need the windows 7 built-in 10/100 BASE - T Ethernet LAN drivers

  I'm trying to reformat the laptop from a friend. Everything works fine including wifi with the exception of the ethernet lan driver. I can't find anywhere. The laptop is a refurbished 15-AC132DS. I downgraded from windows 10 for windows 7 ultimate and switched to legacy BIOS. Ethernet is not detected in the Device Manager and under display adapter settings only wifi.  I can't find the drivers anywhere! Help, please!

  Hello

  Please try:

  http://h20564.www2.HP.com/hpsc/SWD/public/detail?swItemId=ob_126558_1

  Kind regards.

• Equium A100-147 - where to find the ethernet LAN driver

  Hi all

  I have problems to find the dirver for my ethernet controller...
  I went to the toshiba Web site and on the LAN driver is not finished, he does that with any application to uninstall, doesn't have to install, missing problably...
  I could find on the web...

  I managed to install the wirelles, so I can use the net over there... but I want to install the LAN as well...

  Anyone know where I can find driver (ethernet LAN) Equium A100-147? *

  Thank you very much...

  Hello!

  Have you tried to update the BIOS?
  Check the Toshiba site for a newer version of the BIOS:
  http://EU.computers.Toshiba-Europe.com-online decision-making supported Downloads & => Download drivers

  Good bye

• HPPavilion for computer laptop 15-ab516TX: cable Ethernet stuck in the LAN port

  Hello

  Ethernet cable is stuck in my laptop's LAN port.

  He won't get out if I pull/push it.

  I plugged in for the first time in my brand new laptop and don't want to brake it.

  Please help and solutions.

  Should I take my laptop to hp service center.

  Will you please answer soon because I can't travel with hangging cable.

  Help!

  Solved!
  Use a screwdriver and slowly 2 x take the cable into the port of the back of the laptop.
  In this way...
  Safe also take the cable without damaging the laptop components.

• set up a branch to the main ethernet using Airport Extreme network

  Could someone help me with this network configuration please?

  I rent an office and we have an ethernet cable coming into our building to the main network (a fiber broadband building next door). The ethernet line give you IP addresses and internet link.

  I would like to set up our own network in our building-

  1 / would put an Airport Extreme there is the ethernet cable and then plug the cable into the WAN port

  2 / I would implement the EA to distribute IP addresses, but using a different pool - so if the main building uses 192.168.1.1 to 192.168.1.256, I would be created my AE to use 10.1.1.1 to 10.1.1.256

  3 / I would then run an ethernet cable between the port LAN on EI to my Netgear 24 port switch.

  4 / I would connect all our other airport extreme and express again our Ethernet switch and put them all to 'bridge mode '. The switch ethernet cables may be connected to the WAN ports on these airports.

  Anyone see any problem here? We would just to have control over our own IP addresses and be able to restart our Airport Extreme, if we must, do not rely on the building next door to the distribution of intellectual property. I know still need to answer on them for the internet connection, but that's fine.

  Thank you!

  It should work. It would be the basis of a network of mobile type.

  A word of caution. With the exception of the "main" AirPort Extreme that performs as a router, connect the other base stations using their respective ports of LAN. We found some inconsistencies when a base station is in bridge mode and the connection is their WAN port.

• The LAN on an Express port still works as a LAN port when in mode "extend the Wi - Fi network"?

  Assuming that the current versions of all units in the airport:

  If you have an extreme as your primary access point, and you have an Express "extend a Wi - Fi network" mode, the LAN on the Express port still works as a LAN port?

  Yes. You can connect any Ethernet device to that port.

• Re: Satellite Pro L670-103 - not able to connect to the internet using LAN

  Hello

  I am unable to get my L670-103, in the case of Windows 7 Pro (x 64), to connect to the internet via the ethernet jack.

  I tried running the troubleshooter in windows and reinstall the driver ethernet with no luck.
  The computer used to work fine with the same network (I have no control on the network itself, as I'm on a University campus), and my other, much more old laptop (with XP), connects with no bother.

  I'm sure the question is focused on software that - I tried to go online on the same socket after booting from an Ubuntu live CD, and it worked fine.

  What can I do about it?

  Hello

  Can you confirm that the LAN driver was installed successfully?
  What is card LAN recognized correctly in Device Manager?

• Satellite U500 - 1 FC and ethernet LAN speed

  Hello

  I just can't get over 100 Mbps when I am connected to my gigabit router. My other laptop (a HP TX2-1150EF) connects correctly when you use the same cable.
  Properties of Realtek PCIe FE Family Controller speed give me only 10/100/auto negotiate. Tested other realtek drivers with no luck.
  I wonder if U500 - 1FC (PSU9BU) have the gigabit ethernet controller.

  Is this normal?

  Hello

  The card Realtek LAN of the Satellite U500 - 1FC supports 10/100 Mbit, only so that you can use Gbit connection. Sorry but in this case it limitation material s and 100 Mbps is the maximum.

• Satellite P100-113 not the installer for the networking ethernet

  The phone was bought in England, but is used in the USA, model PSPA3E. It runs Windows XP Home Edition sp2. We have Internet high speed brought to our House and I am trying to get the laptop connected to the Internet via an ethernet connection. There is an ethernet port on the back of the laptop, but when I plug the ethernet cable it's a green light (right) and a yellow light (left). When I go into "Device Manager" are 2 network cards that are displayed (a 1394 network adapter and an Intel PRO/Wireless 3945ABG Network Connection). I don't want to use the wireless (which works), I want to use the ethernet. Under "Other devices", there is a yellow question mark and a yellow exclamation mark next to 'Ethernet controller'.

  1. is there an Ethernet on this laptop? I can't under 'Network adapters' then perhaps it is on the motherboard?

  2. I went to the web site of Toshiba UK support and downloaded latest drivers from the LAN 2. I just need to install the most recent a (lan - 20081201075406.zip)?

  Any help would be appreciated.

  Thank you.
  Ted

  Hello!

  1. Yes, the laptop has a LAN port. It is on the motherboard. With this port, you can connect to a router or internet network.

  2. you should only download and install the new driver and Yes, the lan - 20081201075406.zip file is good.

  Good bye

• Ethernet LAN NB200 port is not detected

  Hello world

  I think I have either disabled or deleted the ethernet LAN on my NB200 to remove it from the system tray. (I can use WiFi integrated for networking and access to the internet or an external Bluetooth adapter with my Telstra Next G phone as a modem.)

  Now, I want to activate and use the ethernet port, so I can connect to an old - ish computer using a crossover cable to copy a bunch of files, however I can not the LAN ethernet works again. I tried several times to add hardware and uninstall/reinstall the driver (downloaded from this site), reboot, & etc. without success.

  Any tips or suggestions? Has anyone seen a similar problem before?

  Thank you very much!

  Kind regards
  Daniel

  If she is there, she is disabled? If yes then you can activate it. Right-click on it and select enable from the list.

• My Satellite M100 has Ethernet LAN card?

  Hi guys, im just new here. Can I just ask how will I know if I have an ethernet LAN card? Please do help...

  en thank you kick the guy

  Hi dude

  What do you think of the thing on this forum? Do you something we are clairvoyant! ???
  How is - that someone should provide any info or help without any details on the laptop you! ??? What model of laptop do you have?

  But a tip: check the back side of the laptop. There must be a network (RJ45) port

• Driver Ethernet LAN required - laptop Compaq presario V3777TU for Windows XP

  I removed vista and installed windows XP in my compaq presario V3777TU , but I could not find the suitable driver for Ethernet LAN. Now my system doesnot detect LAN. Card Ethernet in my system is integrated 10/100BASE-T Ethernet LAN.

  Corinne

  You have Marvell Yukon Ethernet:

  FTP://ftp.HP.com/pub/SoftPaq/sp37501-38000/sp37792.exe

  Message edited by CherylG on 03/01/2009 18:55

• Need drivers for the controller ethernet and network on Tecra M2

  I formatted and reinstalled Xp Pro SP2 on my Tecra m2.
  I installed and found all other drivers, but can't seem to find the correct drivers for the network and ethernet devices controllers.

  I downloaded a few different drivers that are compliant with the Tecra M2 but still have yellow question marks.
  If someone could help it would be much appreciated
  Thank you

  Hello

  I guess you need a Wlan card and LAN driver card.
  I a little surprised at your comment, because the WLan and LAN drivers are available on the page of the Toshiba m driver.

  There are 2 Intel Lan and 4 Wlan drivers for different wireless cards. You must choose the right! ;)
  Check the bottom of the unit. There must be a label with a few s Lan and Wlan card information.
  Select the correct drivers and install it.