Ethernet LAN NB200 port is not detected

Similar Questions

• Since the L7680 installation my usb ports are not detected...

  It seems that something in the registry has been changed.  My Western Digital Passport (mass storage device) is not detected is not my SanDisk Micro (2G).  Western Digital will work in the USB from the printer, but don't the SanDisk.  I've lost the use of all of my USB ports on my computer processor and montor.  They used to work before installation.  I uninstalled and reinstalled, I check startup items in MSCONFIG.

  I read on the Microsoft support page which the hkey_local_machine\system\currentControlSet\Control...

  should be set to activate, but I do not have this folder in XP.

  Western Digital does not know what is happening, or not SanDisk.  HP really gave me the run around way to uninstall and reinstall, but I didn't get an answer that solves the problem.

  It seems to me that since it was drivers from HP which caused my other unit to pass unnoticed, HP should be able to tell me how to solve this problem.  I do too much research for a new product.  I know I'm very frustrated, and since this is a new printer I still have time to take it for something that's going to work.  I had a Dell that has worked well, I wanted to just an upgrade.  I guess I could have updated by Dell.

  Just about the evacuation, someone has an idea what the fix is for my USB not detected ports that have been replaced by the reader on this printer?

  I added a new HP printer to my set all my ports no longer works. None of my flash drives or removable hard disks worked. I tried everything and then read "ports must be updated". My computer is older than three years and the ports of origin are 1.1 and are of most new USB 2.0 devices. Long story short, I went to microcenter and bought new ports ($11.00) and add them to my computer. All ports are now functional.

• USB port can not detect my new camera

  My usb port won't detect a device I have ever connect to the port, when I plug the new device, windows cannot install the driver... always failed... help me please...

  Hello

  1. What is the brand and model of the USB device you are trying to connect?

  2. What is the brand and model of the computer?

  I suggest that you try the procedure described in the article mentioned below.

  What to do when a device is not installed correctly
  http://Windows.Microsoft.com/en-CA/Windows7/what-to-do-when-a-device-isn ' t-installed-correctly

  Tips for solving common driver problems

  http://Windows.Microsoft.com/en-CA/Windows/tips-fixing-common-driver-problems#tips-fixing-common-driver-problems=Windows-7

  Hope this solves the problem. If the problem persists, you can write to us and we will be happy to help you further.

• HDMI port is not detected on my Satellite L755-1NX

  Hello

  I have a problem with the conector HDMI to my new laptop, I have bougth 2 weeks ago.
  The laptop detects no HDMI port. When I conect the laptop to a TV or monitor on a different pc, any of these detects anything.

  I tried to update a lot of drivers, old and new drivers Nvidia display drivers Intel... And I also do the 4 recovery DVDs, to restore the laptop to factory settings.

  All this without any solution. When I press Fn + F5, only there is the option of the LCD screen.

  I intend to use the guarantee to repair the laptop, because I think it's a hardware problem.

  What should I do?

  Thank you!

  Hello

  I think you should use the recovery discs that you made in the past.
  Retrieve the computer laptop back to factory settings and check if the HDMI would work again.

  And of course: it is possible that your HDMI cable is not correct.

• Latitude E6430 Port Replicator not detect digital displays during startup

  Hello

  I have two new Dell E6430, both have the same problem. When the laptop is connected, the lid closed and under tension, no monitor active. Only when I power off, then open the lid of the laptop and power on I see the start of the cycle on the laptop screen, it happen then to the monitors. I use the new Duplicator with two digital outputs. When I use the older model with a digital and an analog Port Replicator, the laptop will start to analog and then when the windows screen appears, returns to digital monitor (as it should). As the nvidia driver will not load without the intel first, I loaded all the windows updates and drivers for vidoe intel and nvidia. I also loaded chipset, system utilities and verified bios is updated.

  Someone has experienced this problem or have any ideas that I might be missing?

  1. disable Optima in BIOS

  2. go on Nvidia.com site under drivers and have it detect your video card.

  3. install the Nvidia driver using custom settings, choose clean install. (This will reboot twice during the installation) After the second restart a monitor will start.

  4. change the settings of your video card to drive both monitors.

  at this point to change your power to the 'status quo' setting when the laptop lid is closed. Close the lid and restart.

• USB ports do not detection devices

  Hello

  My USB ports are sensors not when I their connection. I hear the noise, which indicates a device has been connected, but when my laptop is trying to install the driver, it gives me an error Code 39.

  I see an icon in Device Manager yellow triangle-shaped when a device has been plugged in. I tried to uninstall and reinstall my driver and running fixit (said mass storage device USB has a driver problem and can't fix), but no luck.

  I'm running Windows 7 Home Basic Edition and tried to insert a USB Hard Seagate Drive, Kingston and a Sandisk USB key (they all work fine on other computers).

  Help, please!

  Hello Marilou,

  Thank you for your response.

  What is the brand and model of your laptop?

  I appreciate your efforts to resolve the issue.

  I also appreciate the fact that you ran Microsoft fixit.

  However, due to USB devices, I suggest you to try the following methods and check if it helps.

  Method 1:
  Uninstall and reinstall the USB controllers and check. Please follow these steps:

  a. press Windows + R keys, type devmgmt.msc in the run window and press ENTER.
  (b) in Device Manager, expand 'USB Bus controllers'.
  c. a device under "In Bus USB controllers" right click and click on Uninstall.
  d. perform the same step for other devices. Once completed, restart the computer.

  All USB controllers will reinstall automatically.

  If this does not help, use method 2.

  Method 2:
  Turn off the "selective suspend" feature of the USB hub driver and check the issue. Please follow these steps:

  a. press Windows + R keys, type regedit into the run window and press ENTER.
  b. look for, and then click the following key in the registry:

  HKEY_LOCAL_MACHINE\System\CurrentControlSet\Services\USB

  (c) in the "Edit" menu, point to 'New' and then click 'DWORD'.
  d. Type "DisableSelectiveSuspend" and press ENTER.
  e. in the "Edit" menu, click on 'change'.
  f. type '1', and then click ok.

  Note: This setting affects all USB host controller drivers in the system.

  For Windows update number, I suggest you try using the steps described in this article and check.
  Reference:
  Error 0 x 80070005 in Windows Update when you try to install updates
  http://Support2.Microsoft.com/kb/968003

  Important notes:
  Serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base:
  http://Windows.Microsoft.com/en-us/Windows/back-up-registry

  The data files that are infected must be cleaned only by removing the file completely, which means that there is a risk of data loss.

  I hope this information helps.

  Thank you

• USB port does not detect the USB storage

  Hello

  My company gave me a Lenovo ThinkPad L420 and whenever I connect the USB external storage, I am not able to see it on my computer but I can see the unit on Control Panel devices and printers. Please let me know how activate or activate?

  Thank you

  Sayed Toufiq.

  You can google for it!

  http://pcsupport.about.com/od/Windows7/HT/change-drive-letters-Windows-7.htm

• USB 2 not detected mass storage devices

  Windows XP SP3 USB - 2 ports do not detect mass storage devices (reported as unknown device).  Same device is detected and works OK on the USB-1 ports.  Function USB - 2 ports for printers and mass storage OK no (no brightness, without removable hard disks).  Have tried all the simple fixes found on support.microsoft.com.  No success yet.

  Hi Lostcauseracing,
   
  Follow the steps in these articles and check if it helps in fixing the issue:
   
  How to troubleshoot unknown devices listed in Device Manager in Windows XP
   
  Advanced troubleshooting tips for General USB for Windows XP problems

• My new airport does not detect my existing WiFi network, I can connect only via the LAN.

  Bought a new airport 1 TB TimeCapsule and I wanted to add to my existing via a WLAN network. It does not detect it and I can connect only via the LAN. What I am doing wrong?

  Unfortunately, unable to connect to a 3rd time Capsule part wireless using a Wi - Fi.

  You need to connect to the time Capsule to your existing modem/router using a wired Ethernet cable connection, permanent... like the Time Capsule Setup Guide illustrates.

  

  If you really don't want the time Capsule to connect using the wireless... she can do... If it gets a signal to another Apple wireless router. So if you were ready to add another Apple... as an AirPort Extreme router... and connect it to your existing Ethernet cable router/modem and configure AirPort Extreme to broadcast a wireless signal... .then.. .the Time Capsule would be able to connect in this way, assuming that he is where he can receive a good quality of AirPort Extreme wireless signal.

• NB200-12N - USB port does not work

  Hello

  I updgrade my OS from windows 7 starter edition to now a windows 7 home basic 32-bit usb port does not work is the (only) in the left near card reader sd and lan.
  Can you please hellp me to install it? I have download the drivers from Toshiba for my NB200
  But does not work.

  Thank you

  Paulo

  If everything is OK and right drivers all USB ports should work. You cannot install the drivers for each port separately and force one of them to work properly. On this machine, all three ports are the same USB2.0 ports.

  Try reinstalling the chipset utility.

  By the way: two other ports work well, right?

• LAN/WAN ports not supposed to be Gigabit? Capped at 250Mbps, NOT because of the ISP LAN devices.

  Hi all

  Have a bit of a problem here. I have Internet Fiber-to-the-home (FTTH) with Bell Canada and have their Fibe Gigabit service which is 940/120 speeds up and down, respectively. I was able to bypass his combo modem/router using a switch connected to the optical network terminal (HAVE) where the fiber cable enters the House (which serves mainly my base modem) and using custom settings of VLAN and DNS in ports specific for my fiber IPTV service Bell and receivers work together through my router.

  So, I have a few routers that I tried this with to try to solve my problem. My Asus RT-AC5300 and others have no problem with having me my subscribed speed - certainly through devices connected to gigabit LAN and also via WiFi on compatible devices. But I'm not concerned about WiFi - it is specifically wired ethernet devices that are the cause. I use CAT5e and CAT6 cables only because he is a Gigabit connection. The issue I have with my Time Capsule (3 to, latest model AC) is that, literally, speeds for gigabit wired devices will not exceed 250Mbps downstream. Download speeds can hit 125Mbps without problem. Why is this? Is there something my Time Capsule prevents leave the LAN ports operating at gigabit full transfer speed? It is not only a device - I have multiple gigabit devices I tested, on all three of the TC ports, and none of them exceed 250Mbps. Yet when I connect them to another router gigabit, such as the Asus I've described but also others, they have no problem hitting 900 + Mbps downstream on the exact same network configuration and Setup at home.

  Thanks for any ideas, comments or suggestions. Y at - it a setting I have accidentally enabled that is the cause? I had much rather use the TC of the most convenient airport for my network I was planning on getting multiple Airport extreme to position around the House to cover literally home WiFi and LAN bridges through the simple installation of these devices, but I do if I can't use my fiber subscribed speed.

  OR maybe I have a defective unit. Thanks again for the help!

  See you soon

  The issue I have with my Time Capsule (3 to, latest model AC) is that, literally, speeds for gigabit wired devices will not exceed 250Mbps downstream. Download speeds can hit 125Mbps without problem. Why is this?

  Apple AirPort routers have been designed to work with the cable standard and DSL connections.  The fiber is the new ball game, and Apple knows yet how to play the game, let alone to understand the rules.

  Most of the problems associated with connections to high speed on airports is a result of the decision of Apple to eliminate any kind of manual settings to manually adjust the speed of the WAN port on the router... and are based rather on an "Auto" setting.  Automatic adjustment seems to work pretty well on the fiber up to approximately 100 Mbps connections, but the WAN port is struggling to negotiate with high-speed connections when it is connected directly to the fiber. LAN ports can also be affected.

  Some users have reported that insert a Gigabit switch between the connection of the fiber and the Time Capsule or AirPort Extreme has helped with speeds. The theory here is that the switch can negotiate with the fiber connection much better than the WAN port on the Apple device.  If you have a handy Gigabit Ethernet switch, that it could not hurt to try this "Workaround".  Other users report no benefit when they try it.

  Yet when I connect them to another router gigabit, such as the Asus I've described but also others, they have no problem hitting 900 + Mbps downstream on the exact same network configuration and Setup at home.

  The time Capsule is not directly connected to the fiber connection, so it OK to talk and negotiate with what he sees as a 'normal' a conventional router connection.

  Don't forget also that the 802.11ac products were designed before 2013. Current products have not changed since their introduction in June 2013.

  The bottom line... Apple needs to decide whether it wants to be an actor, or leave the routing other players company established. Such what, Apple is far behind the curve... my opinion.

  While it might not hurt to take the time Capsule to an Apple Store to check over the machine, you might want to ensure that they have in fact a fiber connection high speed to test.

• HP m8120n no Ethernet in the Device Manager and not detected

  Hey all:

  I have a desktop HP Pavilion Media Center m8120n (product sheet here) and I recently did an installion of installation clean factory, Windows 7 Pro 64 bit with a DVD retail of Windows. I managed to get the drivers for almost everything, but there are some persistent problems.

  The most serious of them is Ethernet. I can't find drivers ethernet for this machine, even after the update of Windows running several times, no hardware drivers have been found. The ethernet controller/port is not still appear in Device Manager at all!

  I tried to use the driver for this calculation pager on the HP support site, but there is no mention of all the Ethernet/LAN drivers at all.

  I read that sometimes it is important to update the chipset first driver in order to get the job of ethernet. Since HP provides no chipset driver, I decided to try updating the chipset 8120n with theutility to update Intel drivers Intel's Support page.  I have updated to version 9.4.0.1017, once the Web page has scanned my system. However, even after the update the chipset and Windows restarts, I have still no Ethernet at all.

  Depending on the product specifications page, under the section network, the computer uses a controller Ethernet Intel 82566DC. However, after trying to install the driver for the Intel 82566DC since the Intel, the installer website told me that no network controller Intel were present on the system.

  What is really worrying, is that not only does the Device Manager does not even see an Ethernet controller, but the Intel drivers update utility didn't recognize it under the section "Wired" after that the latter had analyzed my computer. Ethernet controller also does not appear under system information.

  I'm starting to wonder if it is a hardware issue and not a driver problem at all! The Ethernet port may be damaged or does not work for Windows do not install the drivers, or even recognize it.

  Does anyone have advice or steps I could take to rule the hardware problem and find a driver that works for my installation of Windows 7 on this computer?

  "Violence is the last refuge of the incompetent." -Issac Asimov, from its roman Foundation.

  Good new! It worked! It was really the BIOS that was causing the problem.

  On the Advanced Settings tab, there is an entry called Onboard LAN off, just like the desktop I have to work!

  After booting, Windows installed the drivers for it right away, and now I get to enjoy this sweet Gigabit speed on my network!

  I'm so happy that it was not a hardware problem, and that it was a simple change to the configuration of the BIOS.

  Thanks for all your help!

  I'm as resolved marker.

• Creating team to implement the dual ethernet LAN port?

  My new card mother ASRock Z87 Extreme9/ac features dual Ethernet LAN which is supposed to improve my internet connection.  This procedure requires my double Ethernet ports to be "associated".  I would be grateful if someone can tell me how to do this.  Unfortuantely, guide the user to ASRock is rather rare and Tweak Town forum, that they hold a candle to the contributors here.  Thank you.

  Hello

  You can consult the following Microsoft article and check if it helps.

  http://TechNet.Microsoft.com/en-us/library/hh831648.aspx

  
  Note: There is also good place for Windows 8.

• My Ethernet port is not running iMac mid 2011. Pls help me.

  Hi, I have an iMac 21.5 "mid-2011. My Ethernet port is not working. Is this a software problem? Pls help me.

  Try resetting the SMC reset management system (SCM) controller on your Mac - Apple Support

  Try another ethernet cable.

  He still does not? A report with the information more wrote an effective communities of Apple Support question

• Peripheral storage but not with ethernet connection USB port work

  I usually connect my Mac Book Pro with ethernet using the USB port. It was working fine, but since a few weeks, it has stopped working. But the normal usb storage devices only works very well in this port. So, I tried to connect the ethernet to another USB port near the seizure of power, which seems to work very well. So, that means that the other USB port does not work properly. How can I fix? I use Mac Book Pro with the Version OS X El Capitan 10.11.4

  Try resetting the SMC reset management system (SCM) controller on your Mac - Apple Support

  Shouldn't use you a crush on Ethernet card instead of a USB adapter to Ethernet?