Device does not connect error 507

Similar Questions

• BlackBerry Smartphones Blackberry 8520 wiped and does not show error 507

  Hi, I recently wiped my blackberry 8520 OS with BBSAK and started to install another OS, in the process, the USB cable somehow has been disconnected and installation has failed. Now the phone just to start, turn on for about 3 seconds shows nothing and then turns off. It does not show same error 507. Help, please

  Hello and welcome to the community!

  You may need to use these tips:

  • KB10144 How to force detect the BlackBerry smartphone using the Application Loader
  • KB27956 How to recover a BlackBerry smartphone from any State
  • http://CrackBerry.com/BlackBerry-101-lecture-12-how-reload-operating-system-nuked-BlackBerry

  Good luck and let us know!

• Devices does not connect wireless. Validation of identity?

  I have a Wireless-g router broadband model # WRT54GS2, the source of the internet is a Sprint card mobile broadband px-500 that plugs into my laptop.  The router and connection worked very well until someone hit the hard reset on the router button.  I have configured the router using the provided installation cd.  After the reset button has been affected, I tried to use the cd to resolve the connection problem but, I can't use the cd because it repeat 301 error: internal error.  Is there something I can do to set up the router again and get the connection going manually?  I can connect to the wireless using a laptop but it says validation of identity, and the connection will not work.  How can I fix this?!  THX!

  -Also, I know how to get on the web based Setup by putting my ip address in the browser but, I don't know how to fix my connection problem.

  With the computer connected wireless to your router, open the web interface at http://192.168.1.1/ the default password is "admin". Now, perform the following steps:

  1. change the address LAN IP of 192.168.1.1 to 192.168.0.254 WRT.
  2. on the same page, disable the DHCP server.
  3. save the settings. You will lose the connection.

  4. connect one of the LAN ports numbered from the WRT to the ethernet port on your computer with the card Strip. Do not use the internet port of the WRT!

  That should do it. Now all your other computers can connect to the internet through the computer with the card Strip.

  Remember that from now on, you need to configure the WRT on http://192.168.0.254/ also don't forget to secure the router, either change the default password on the Administration and a separate SSID page and enable security wireless WPA2 with a password hard.

• Just got rid of the virus Security essentials 2010 and now none of my network devices does not work error code 39

  Hey

  Just got rid of SE 2010 from my pc and now none of the network on my pc devices work continues to come up with the error code 39 and .dll is not found I tried re-installing the drivers and still no change please help also I can't uninstall it from the device or the other.

  XP forums:

  http://social.answers.Microsoft.com/forums/en-us/category/WindowsXP

  Link above is for XP Forums.

  There is a list of the different Forums XP to the link above to help you.

  You get the help you need there.

  Here is the Vista Forums.

  See you soon

  Mick Murphy - Microsoft partner

• Time Capsule - devices do not connect

  I have a Time Capsule router. I had problems with the devices does not connect to the internet. Restart the previous device will connect then another will not. I have ~ 20 devices on my wireless network. I replaced my DSL modem but the problem persists.

  Any time that you change your network hardware, it's always a good idea to perform a complete recycling of your network equipment power. Check out the following Tip of an airport users for more details on how to do it. Please post back your results.

• Motorola Milestone does not connect to the corporate network after updating to Froyo...

  I've updated my Milestone that is the version of Froyo UNITED Arab Emirates yesterday after a long delay, was really excited all night until I've discovered two problems with my wifi.

  The device does not connect to the corporate network, as my office uses EAP 802.1 x and there is no place to enter proxy where my friends using samsung galaxy s (Froyo 2.2) connect to the network and navigate using the wifi settings advanced to enter the proxy in their device.

  Any help? Please, I beg you.

  Hey Ronald, I've updated by upper about the update saying that UNITED Arab Emirates and EGYPT got last week. Don't know if the Saudi version has achieved, you have the Saudi Version or is it the same in the UNITED Arab Emirates. If his UNITED Arab Emirates you can do it via the PC using Software updater by Motorola...

• There is an error with my computer, it does not connect with my router. It works with my usb 3g modem, but not with my router. My router works with other devices.

  There is an error with my computer, it does not connect with my router. It works with my usb 3g modem, but not with my router. My router works with other devices.
  I tried to connect my xbox to my computer to xbox live via the 3g router, but I was unable to. According to me, there is something wrong with the network card, since neither the wifi (wlan?) nor the lan connection seem to work.
  I harnessed connected my iPod, Xbox 360 and Nintendo DS for her, but not my computer. Please help me, what wrong with my computer?

  original title: problem with the map?

  Hi GustavTak,

  1. you have made no changes to the computer before the broadcast took place?
  2. do you get an error message?

  Try the steps from the following link:

  Windows wireless and wired network connection problems
  http://Windows.Microsoft.com/en-us/Windows/help/wired-and-wireless-network-connection-problems-in-Windows

  Additional information:
  Network connection problems
  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-network-connection-problems

  Set up a wireless router
  http://Windows.Microsoft.com/en-us/Windows-Vista/set-up-a-wireless-router

• Error: This device does not work properly because Windows cannot load the...

  I get this error message "this device does not work properly because Windows cannot load the drivers required for this device. (Code 31) "via a wired connection. And that's the Microsoft 6to4 adapt #7 and the same card but the #4 one.  Are these drivers or another file that I could use DL?

  Hi JasonBedgood,

  1. Once you get the error message?
  2. did you of recent changes on the computer?

  This error occurs if the required driver is not installed or the driver is damaged.

  I suggest that you update the driver for the device and check.

  How can I update the driver for network card on the computer

  1. click on Start, click Control Panel, and then double-click System.
  2. click the tab hardware , and then click Device Manager.
  NOTE: If you are prompted for an administrator password or for confirmation, type the password, or click continue.
  3. click on network adapters to expand.
  4. under network adapters, double-click the entry for Microsoft 6to4and then click driver .
  5. click on Update driver software.
  6. follow the Wizard update software driver to update the driver for NICs .

  Updated a hardware driver that is not working properly
  http://Windows.Microsoft.com/en-us/Windows-Vista/update-a-driver-for-hardware-that-isn ' t-work correctly

  If the device driver update did not help then check the link below for one of the thread with the question and try the steps mentioned by Lionel Chen on January 9, 2008
  http://social.technet.Microsoft.com/forums/en-us/itprovistahardware/thread/3a503cdb-e61c-44BC-97c4-0b38b0e5f929/

  I hope this helps!

  Halima S - Microsoft technical support.
  Visit our Microsoft answers feedback Forum and let us know what you think.

• How to solve 'error display driver - video playback device does not support playback of protected content?

  This message started on my installation of windows 7 media center with the installation of tuner Cable Digital ati a few months.  I had the computer in my office with no monitor for a while and watched TV through my xbox on my samsung ln52b610.  so I decided to connect to the PC directly to the tv and now get this message saying 'error display driver - video playback device does not support playback of protected content'.  the strange thing is that if I go full screen, then new Media Center, here again, it seems to go away (most of the time).  my video card is a 8500gt nvidia with hdmi output and I tried the latest driver from them and still no worky.

  Take a look at the support links that can help solve your problem.

  http://answers.Microsoft.com/en-us/Windows/Forum/Windows_7-TV/protected-content-error-after-a-few-seconds-of/da074c94-e741-E011-9767-d8d385dcbb12

  http://social.technet.Microsoft.com/forums/BG-BG/w7itpromedia/thread/3eea4165-8e37-42b7-A396-62663cc516a7

  If no go, Greenbutton forum would be place to post the question: http://thegreenbutton.com/forums/

• Series USB drivers does not start error: "this device cannot start. (Code 10) »

  Hello

  I have a usb_dev_serial.inf of TI and a catalogue of security usb_dev_serial_amd64 and a folder containing the amd64
  the DLLs below.  When I used the Add Hardware Wizard to load the .inf, properties of the pilot were "this device cannot start. (Code 10)"
  Does anyone have a suggestion?
  Thank you
  Larry

  Hi Larry,

  Thanks for posting in the Microsoft Community Forum. According the description, I understand that the USB device does not work, rest assured that we will do our best to help you with this problem.

  Answering the question that helps us provide the best solution:

  1. it worked before?
  2 have had any changes made to the computer before the question?

  The Code 10 error applies mainly to the problems of hardware driver and devices or compatibility problems between the drivers of equipment and additional software that is installed in Windows. Therefore, we recommend that solve you these problems with emphasis on device drivers, configuration of device problems and hardware compatibility issues.

  Try the following and see if it helps.

  Method 1:

  Description of errors related to the 10 Code that generates the Device Manager in Windows on computers:

  http://support.Microsoft.com/kb/943104

  Method 2:

  Install the latest driver for USB and check if that helps.

  To do;

  a. click Start, type devmgmt.msc in the start search menu.

  b. right-click on the USB device and click on Update driver software.

  Updated a hardware driver that is not working properly:

  http://Windows.Microsoft.com/en-us/Windows7/update-a-driver-for-hardware-that-isn ' t-work correctly

  Method 3:

  Try connecting to another USB port and check if it helps.

  Hope this information helps. If you have any other questions feel free to respond and we would be happy to help.

• Error: Your device is not connected to the Internet.

  Hello

  I have a dash HID - B70 model and until last week it works fine. I used about 2 weeks ago and have had on energy saving mode after that. I tried to use it again a couple of days, and when I typed on the screen the unit remained in power save screen and showed a yellow above the clock error message: "your device is not connected to the Internet. Press to reconnect. "I hit this button and the unit tried to reconnect, but will still end up back in the same error message and the screen.
  I tried to push the reset button on the device, but I still see the same black screen and the clock with the error message once it restarts. I unplugged my wireless router and managed to get the device to show me the other wireless networks, then I plugged the router back in and reconnected (device showed that the connection was successful), but then he went immediately to the error screen.
  I can't the unit to go to the home menu at all, no matter what button I push, if unfortunately I can't even reset to factory settings to avoid the problem.

  Any advice on how to fix this? I do know not why it happened because I didn't have the routers or wireless providers, nor have I added all devices on my home network.

  Thanks in advance for your help.

  
  

• Pavilion G6 does not connect to the cellular device

  I have a Pavilion G6 with Windows 7 OS, which is used as a mobile data terminal. I am trying to use my iPhone Verizon 5 c to connect to a hotspot. All my other HP laptops connect to this phone without problem, but the G6 does not connect to the internet via the phone with cable, wifi or bluetooth. The G6 recognizes the phone and shows it in "unspecified devices." I tried everything to get it to connect without success.

  Hey RC800,.

  Thanks for the info.

  I forgot to ask before, can you tell me the exact model specifications what do you use? For more information on the search for your model and product numbers, click here: How can I find my model number or product number?

  If the laptop connects to other devices, we can say that the material is very good. If he does not see the iPhone theres only a few things you can try. The adapter in your laptop is probably 802.11 g capable which is the minimum requirement for the hotspot iPhone, so we can exclude.

  Please, try the following:

  Turn off the power to the adapter:
  1. open Device Manager. (Win Key + R > type devmgmt.msc > OK)
  2. expand the network adapters.
  3. right click on the Ethernet adapter / wireless, and then click Properties.
  4. click on the power management tab.
  5 remove the check mark next to allow the computer to turn off this device to save power.
  6. click on OK.
  7 test cycle.
  
  Reset the TCP/IP settings on your PC:
  1. go to your start screen/menu and type CMD.
  2. right-click on the command prompt icon and select run as administrator.
  3. in the window that opens type "netsh int ip reset resetlog.txt" without the quotes and press ENTER.
  4 restart your PC and test.
  
  It can also help to reset the winsock catalog:
  1. go to your start screen/menu and type CMD.
  2. right-click on the command prompt icon and select run as administrator.
  3. in the window that opens type "netsh winsock reset" without the quotes, and then press ENTER.
  4 restart your PC and test.
  
  Reinstall the NIC drivers:
  1. download the drivers from here , but do not run them again.
  2. go to your Start menu/screen and type Device Manager.
  3. expand network adapters.
  4. right click on the wireless adapter and choose uninstall.
  5 install the drivers downloaded in step 1.
  6. restart your PC and test.
  
  Test another iPhone connection:
  Explicit. This will tell us if it's only an incompatibility with a phone or any iPhone hotspot. Try a hotspot Android will help narrow things down as well.

  Let me know if this helps.

• I get an error code, ""this device does not work properly because Windows cannot load the drivers required for this device. " (Code 31) "on the computer.

  My drive hard seagate is not recognized on my laptop, I can see it in the legacy of the laptop but has an exclamation deside it, there a message when I tried to solve the problems, error was not fixed, the device status is "this device does not work properly because Windows cannot load the drivers required for this device. (Code 31) »

  Is anyone know how can I access my hard drive again?

  Thank you

  Hello

  You has made changes to the system before the error appearing?  Cancel the changes.

  (1) in Device Manager > right click on the driver, and then select uninstall

  Reboot and Windows will reload the driver

  (2) remove the upper & lower filters that cause errors in Code 31

  http://pcsupport.about.com/od/driverssupport/HT/UpperFilters-LowerFilters.htm

  Access the manufacturer's Web site and search for updated driver

• Laptop does not connect to the internet. error cannot display Web page

  Original title: laptop does not connect to the internet. How can I fix it?

  I'm trying to get my laptop to connect to internet, but it will not. It keeps telling me that it cannot display the Web page. The wireless connection is the link and he sees the laptop, but it's like he goes. How can I fix it? Help!

  Hello

  1. Have you tried using anythird party web browser to connect to Internet?
  2. You use Internet Explorer to surf the Internet?

  If you receive error message cannot display Web page in Internet Explorer, then you can check the link below to fix the problem.

  "Internet Explorer cannot display the webpage" error when you view a Web site in Internet Explorer

  http://support.Microsoft.com/kb/956196

  Note:

  Reset the Internet Explorer settings can reset security settings or privacy settings that you have added to the list of Trusted Sites. Reset the Internet Explorer settings can also reset parental control settings. We recommend that you note these sites before you use the reset Internet Explorer settings

• All of a sudden, my dell inspiron 6000 does not connect to the internet and has an error message to see article 871122.

  New error message to see article 871122

  All of a sudden, my dell inspiron 6000 does not connect to the internet and has an error message to see article 871122. That's happened? I used it last night to check my email, and then I deleted some photos on the disk hard and this morning it will not connect. I don't really understand what happened to him because it was off last night.

  Hello

  1. you are using a wireless connection?

  If you are using a wireless connection, I suggest you to update the latest drivers for the network adapter and check if it helps:
  http://support.Microsoft.com/kb/283658

  Also check this link for troubleshooting steps:
  http://support.Microsoft.com/kb/314095

  It will be useful.